For all the devices that support being hotplugged (disk, net, pmem, fs
and vsock) add "pci_segment" option and propagate that through to the
addition onto the PCI busses.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This currently contains only the number over PCI segments to create.
This is limited to 16 at the moment which should allow 496 user specified
PCI devices.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When using PVH for booting (which we use for all firmwares and direct
kernel boot) the Linux kernel does not configure LA57 correctly. As such
we need to limit the address space to the maximum 4-level paging address
space.
If the user knows that their guest image can take advantage of the
5-level addressing and they need it for their workload then they can
increase the physical address space appropriately.
This PR removes the TDX specific handling as the new address space limit
is below the one that that code specified.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The argument `prefault` is provided in MemoryManager, but it can
only be used by SGX and restore.
With prefault (MAP_POPULATE) been set, subsequent page faults will
decrease during running, although it will make boot slower.
This commit adds `prefault` in MemoryConfig and MemoryZoneConfig.
To resolve conflict between memory and restore, argument
`prefault` has been changed from `bool` to `Option<bool>`, when
its value is None, config from memory will be used, otherwise
argument in Option will be used.
Signed-off-by: Yu Li <liyu.yukiteru@bytedance.com>
This concept ends up being broken with multiple types on input connected
e.g. console on TTY and serial on PTY. Already the code for checking for
injecting into the serial device checks that the serial is configured.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
It is forbidden that the same memory zone belongs to more than one
NUMA node. This commit adds related validation to the `--numa`
parameter to prevent the user from specifying such configuration.
Signed-off-by: Henry Wang <Henry.Wang@arm.com>
Correct operation of user devices (vfio-user) requires shared memory so
flag this to prevent it from failing in strange ways.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This allows the user to specify devices that are running in a different
userspace process and communicated with vfio-user.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This new option allows the user to define a list of SGX EPC sections
attached to a specific NUMA node.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to uniquely identify each SGX EPC section, we introduce a
mandatory option `id` to the `--sgx-epc` parameter.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Sometimes we need balloon deflate automatically to give memory
back to guest, especially for some low priority guest processes
under memory pressure. Enable deflate_on_oom to support this.
Usage: --balloon "size=0,deflate_on_oom=on" \
Signed-off-by: Fei Li <lifei.shirley@bytedance.com>
Adding the support for an OVS vhost-user backend to connect as the
vhost-user client. This means we introduce with this patch a new
option to our `--net` parameter. This option is called 'server' in order
to ask the VMM to run as the server for the vhost-user socket.
Fixes#1745
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
error: name `FinalizeTDX` contains a capitalized acronym
--> vmm/src/vm.rs:274:5
|
274 | FinalizeTDX(hypervisor::HypervisorVmError),
| ^^^^^^^^^^^ help: consider making the acronym lowercase, except the initial letter: `FinalizeTdx`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#upper_case_acronyms
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
warning: name `LocalAPIC` contains a capitalized acronym
--> vmm/src/cpu.rs:197:8
|
197 | struct LocalAPIC {
| ^^^^^^^^^ help: consider making the acronym lowercase, except the initial letter: `LocalApic`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#upper_case_acronyms
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The help information displayed for our `--disk` option is incorrect and
incomplete, e.g. missing the `direct` and `poll_queue` field.
Signed-off-by: Bo Chen <chen.bo@intel.com>
If the function can never return an error this is now a clippy failure:
error: this function's return value is unnecessarily wrapped by `Result`
--> virtio-devices/src/watchdog.rs:215:5
|
215 | / fn set_state(&mut self, state: &WatchdogState) -> io::Result<()> {
216 | | self.common.avail_features = state.avail_features;
217 | | self.common.acked_features = state.acked_features;
218 | | // When restoring enable the watchdog if it was previously enabled. We reset the timer
... |
223 | | Ok(())
224 | | }
| |_____^
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#unnecessary_wraps
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add the ability for cloud-hypervisor to create, manage and monitor a
pty for serial and/or console I/O from a user. The reasoning for
having cloud-hypervisor create the ptys is so that clients, libvirt
for example, could exit and later re-open the pty without causing I/O
issues. If the clients were responsible for creating the pty, when
they exit the main pty fd would close and cause cloud-hypervisor to
get I/O errors on writes.
Ideally the main and subordinate pty fds would be kept in the main
vmm's Vm structure. However, because the device manager owns parsing
the configuration for the serial and console devices, the information
is instead stored in new fields under the DeviceManager structure
directly.
From there hooking up the main fd is intended to look as close to
handling stdin and stdout on the tty as possible (there is some future
work ahead for perhaps moving support for the pty into the
vmm_sys_utils crate).
The main fd is used for reading user input and writing to output of
the Vm device. The subordinate fd is used to setup raw mode and it is
kept open in order to avoid I/O errors when clients open and close the
pty device.
The ability to handle multiple inputs as part of this change is
intentional. The current code allows serial and console ptys to be
created and both be used as input. There was an implementation gap
though with the queue_input_bytes needing to be modified so the pty
handlers for serial and console could access the methods on the serial
and console structures directly. Without this change only a single
input source could be processed as the console would switch based on
its input type (this is still valid for tty and isn't otherwise
modified).
Signed-off-by: William Douglas <william.r.douglas@gmail.com>
This allows the user to use an alternative huge page size otherwise the
default size will be used.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This patch enables multi-queue support for creating virtio-net devices by
accepting multiple TAP fds, e.g. '--net fds=3:7'.
Fixes: #2164
Signed-off-by: Bo Chen <chen.bo@intel.com>
Add an "fd=" parameter to allow specifying a TAP fd to use. Currently
only one fd for one queue pair is supported.
Fixes: #2052
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add config parameter to --disk called "_disable_io_uring" (the
underscore prefix indicating it is not for public consumpion.) Use this
option to disable io_uring if it would otherwise be used.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The standalone `--balloon` parameter being fully functional at this
point, we can get rid of the balloon options from the --memory
parameter.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This introduces a new way of defining the virtio-balloon device. Instead
of going through the --memory parameter, the idea is to consider balloon
as a standalone virtio device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The watchdog device is created through the "--watchdog" parameter. At
most a single watchdog can be created per VM.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In order to let the user choose maximum address space size, this patch
introduces a new option `max_phys_bits` to the `--cpus` parameter.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This is a new clippy check introduced in 1.47 which requires the use of
the matches!() macro for simple match blocks that return a boolean.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The virtio-balloon change the memory size is asynchronous.
VirtioBalloonConfig.actual of balloon device show current balloon size.
This commit add memory_actual_size to vm.info to show memory actual size.
Signed-off-by: Hui Zhu <teawater@antfin.com>
Misspellings were identified by https://github.com/marketplace/actions/check-spelling
* Initial corrections suggested by Google Sheets
* Additional corrections by Google Chrome auto-suggest
* Some manual corrections
Signed-off-by: Josh Soref <jsoref@users.noreply.github.com>
Add the new option 'hotplugged_size' to both --memory-zone and --memory
parameters so that we can let the user specify a certain amount of
memory being plugged at boot.
This is also part of making sure we can store the virtio-mem size over a
reboot of the VM.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In anticipation for resizing support of an individual memory zone,
this commit introduces a new option 'hotplug_size' to '--memory-zone'
parameter. This defines the amount of memory that can be added through
each specific memory zone.
Because memory zone resize is tied to virtio-mem, make sure the user
selects 'virtio-mem' hotplug method, otherwise return an error.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The goal of this commit is to rename the existing NUMA option 'id' with
'guest_numa_id'. This is done without any modification to the way this
option behaves.
The reason for the rename is caused by the observation that all other
parameters with an option called 'id' expect a string to be provided.
Because in this particular case we expect a u32 representing a proximity
domain from the ACPI specification, it's better to name it with a more
explicit name.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The way to describe guest NUMA nodes has been updated through previous
commits, letting the user describe the full NUMA topology through the
--numa parameter (or NumaConfig).
That's why we can remove the deprecated and unused 'guest_numa_node'
option.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This new option provides a new way to describe the memory associated
with a NUMA node. This is the first step before we can remove the
'guest_numa_node' option from the --memory-zone parameter.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
