SGX expects the EPC region to be reported as "reserved" from the e820
table. This patch adds a new entry to the table if SGX is enabled.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The support for SGX is exposed to the guest through CPUID 0x12. KVM
passes static subleaves 0 and 1 from the host to the guest, without
needing any modification from the VMM itself.
But SGX also relies on dynamic subleaves 2 through N, used for
describing each EPC section. This is not handled by KVM, which means
the VMM is in charge of setting each subleaf starting from index 2
up to index N, depending on the number of EPC sections.
These subleaves 2 through N are not listed as part of the supported
CPUID entries from KVM. But it's important to set them as long as index
0 and 1 are present and indicate that SGX is supported.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Instead of passing the GuestMemoryMmap directly to the CpuManager upon
its creation, it's better to pass a reference to the MemoryManager. This
way we will be able to know if SGX EPC region along with one or multiple
sections are present.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The SGX EPC region must be exposed through the ACPI tables so that the
guest can detect its presence. The guest only get the full range from
ACPI, as the specific EPC sections are directly described through the
CPUID of each vCPU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on the presence of one or multiple SGX EPC sections from the VM
configuration, the MemoryManager will allocate a contiguous block of
guest address space to hold the entire EPC region. Within this EPC
region, each EPC section is memory mapped.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Introducing the new CLI option --sgx-epc along with the OpenAPI
structure SgxEpcConfig, so that a user can now enable one or multiple
SGX Enclave Page Cache sections within a contiguous region from the
guest address space.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In this commit we saved the BDF of a PCI device and set it to "devid"
in GSI routing entry, because this field is mandatory for GICv3-ITS.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
Move the definition of RawFile from virtio-devices crate into qcow
crate. All the code that consumes RawFile also already depends on the
qcow crate for image file type detection so this change breaks the
need for the qcow crate to depend on the very large virtio-devices
crate.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This commit store balloon size to MemoryConfig.
After reboot, virtio-balloon can use this size to inflate back to
the size before reboot.
Signed-off-by: Hui Zhu <teawater@antfin.com>
Remove the vmm dependency from vhost_user_block and vhost_user_net where
it was existing to use config::OptionParser. By moving the OptionParser
to its own crate at the top-level we can remove the very heavy
dependency that these vhost-user backends had.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Refactored the construction of KVM IOCTL rules for Seccomp.
Separating the rules by architecture can reduce the risk of bugs and
attacks.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
In order to move the hypervisor specific parts of the VM exit handling
path, we're defining a generic, hypervisor agnostic VM exit enum.
This is what the hypervisor's Vcpu run() call should return when the VM
exit can not be completely handled through the hypervisor specific bits.
For KVM based hypervisors, this means directly forwarding the IO related
exits back to the VMM itself. For other hypervisors that e.g. rely on the
VMM to decode and emulate instructions, this means the decoding itself
would happen in the hypervisor crate exclusively, and the rest of the VM
exit handling would be handled through the VMM device model implementation.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix test_vm unit test by using the new abstraction and dropping some
dead code.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
The code is purely for maintaining an internal counter. It is not really
tied to KVM.
No functional change.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
The _fd suffix is KVM specific. But since it now point to an hypervisor
agnostic hypervisor::Vm implementation, we should just rename it vm.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The _fd suffix is KVM specific. But since it now point to an hypervisor
agnostic hypervisor::Vm implementation, we should just rename it vm.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fd naming is quite KVM specific. Since we're now using the
hypervisor crate abstractions, we can rename those into something more
readable and meaningful.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fd naming is quite KVM specific. Since we're now using the
hypervisor crate abstractions, we can rename those into something more
readable and meaningful.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fd naming is quite KVM specific. Since we're now using the
hypervisor crate abstractions, we can rename those into something more
readable and meaningful. Like e.g. vcpu or vm.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Split the generic virtio code (queues and device type) from the
VirtioDevice trait, transport and device implementations.
This also simplifies the feature handling in vhost_user_backend as the
vm-virtio crate is no longer has any features.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
On x86 architecture, we need to save a list of MSRs as part of the vCPU
state. By providing the full list of MSRs supported by KVM, this patch
fixes the remaining snapshot/restore issues, as the vCPU is restored
with all its previous states.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Some vCPU states such as MP_STATE can be modified while retrieving
other states. For this reason, it's important to follow a specific
order that will ensure a state won't be modified after it has been
saved. Comments about ordering requirements have been copied over
from Firecracker commit 57f4c7ca14a31c5536f188cacb669d2cad32b9ca.
This patch also set the previously saved VCPU_EVENTS, as this was
missing from the restore codepath.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The logic can be shared among hypervisor implementations.
The 'static bound is used such that we don't need to deal with extra
lifetime parameter everywhere. It should be okay because we know the
entry type E doesn't contain any reference.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
This trait contains a function which produces a interrupt routing entry.
Implement that trait for KvmRoutingEntry and rewrite the update
function.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
The observation is only the route entry is hypervisor dependent.
Keep a definition of KvmMsiInterruptManager to avoid too much code
churn.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
The observation is that only the route field is hypervisor specific.
Provide a new function in blanket implementation. Also redefine
KvmRoutingEntry with RoutingEntry to avoid code churn.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
The observation is that the GSI hashmap remains untouched before getting
passed into the MSI interrupt manager. We can create that hashmap
directly in the interrupt manager's new function.
The drops one import from the interrupt module.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
This is a hash table of string to hash tables of u64s. In JSON these
hash tables are object types.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Because we don't want the guest to miss any event triggered by the
emulation of devices, it is important to resume all vCPUs before we can
resume the DeviceManager with all its associated devices.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
We need consistency between pause/resume and snapshot/restore
operations. The symmetrical behavior of pausing/snapshotting
and restoring/resuming has been introduced recently, and we must
now ensure that no matter if we're using pause/resume or
snapshot/restore features, the resulting VM should be running in
the exact same way.
That's why the vCPU state is now stored upon VM pausing. The snapshot
operation being a simple serialization of the previously saved state.
The same way, the vCPU state is now restored upon VM resuming. The
restore operation being a simple deserialization of the previously
restored state.
It's interesting to note that this patch ensures time consistency from a
guest perspective, no matter which clocksource is being used. From a
previous patch, the KVM clock was saved/restored upon VM pause/resume.
We now have the same behavior for TSC, as the TSC from the vCPUs are
saved/restored upon VM pause/resume too.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Instead of calling the resume() function from the CpuManager, which
involves more than what is needed from the shutdown codepath, and
potentially ends up with a deadlock, we replace it with a subset.
The full resume operation is reserved for a VM that has been paused.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
We want each Vcpu to store the vCPU state upon VM pausing. This is the
reason why we need to explicitly implement the Pausable trait for the
Vcpu structure.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When set_user_memory_region was moved to hypervisor crate, it was turned
into a safe function that wrapped around an unsafe call. All but one
call site had the safety statements removed. But safety statement was
not moved inside the wrapper function.
Add the safety statement back to help reasoning in the future. Also
remove that one last instance where the safety statement is not needed .
No functional change.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
That removes one more KVM-ism in VMM crate.
Note that there are more KVM specific code in those files to be split
out, but we're not at that stage yet.
No functional change.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
Collate the virtio device counters in DeviceManager for each device that
exposes any and expose it through the recently added HTTP API.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The counters are a hash of device name to hash of counter name to u64
value. Currently the API is only implemented with a stub that returns an
empty set of counters.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The structure is tightly coupled with KVM. It uses KVM specific
structures and calls. Add Kvm prefix to it.
Microsoft hypervisor will implement its own interrupt group(s) later.
No functional change intended.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
Now that the VMM uses KVM_KVMCLOCK_CTRL from the KVM API, it must be
added to the seccomp filters list.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Through the newly added API notify_guest_clock_paused(), this patch
improves the vCPU pause operation by letting the guest know that each
vCPU is being paused. This is important to avoid soft lockups detection
from the guest that could happen because the VM has been paused for more
than 20 seconds.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
It's important that on restore path, the CpuManager's vCPU gets filled
with each new vCPU that is being created. In order to cover both boot
and restore paths, the list is being filled from the common function
create_vcpu().
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that the VMM uses both KVM_GET_CLOCK and KVM_SET_CLOCK from the KVM
API, they must be added to the seccomp filters list.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to maintain correct time when doing pause/resume and
snapshot/restore operations, this patch stores the clock value
on pause, and restore it on resume. Because snapshot/restore
expects a VM to be paused before the snapshot and paused after
the restore, this covers the migration use case too.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When a request is made to increase the number of vCPUs in the VM attempt
to reuse any previously removed (and hence inactive) vCPUs before
creating new ones.
This ensures that the APIC ID is not reused for a different KVM vCPU
(which is not allowed) and that the APIC IDs are also sequential.
The two key changes to support this are:
* Clearing the "kill" bit on the old vCPU state so that it does not
immediately exit upon thread recreation.
* Using the length of the vcpus vector (the number of allocated vcpus)
rather than the number of active vCPUs (.present_vcpus()) to determine
how many should be created.
This change also introduced some new info!() debugging on the vCPU
creation/removal path to aid further development in the future.
TEST=Expanded test_cpu_hotplug test.
Fixes: #1338
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
After the vCPU has been ejected and the thread shutdown it is useful to
clear the "kill" flag so that if the vCPU is reused it does not
immediately exit upon thread recreation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
These messages are intended to be useful to support debugging related to
vCPU hotplug/unplug issues.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The same way the VM and the vCPUs are restored in a paused state, all
devices associated with the device manager must be restored in the same
paused state.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Because we need to pause the VM before it is snapshot, it should be
restored in a paused state to keep the sequence symmetrical. That's the
reason why the state machine regarding the valid VM's state transition
needed to be updated accordingly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
To follow a symmetrical model, and avoid potential race conditions, it's
important to restore a previously snapshot VM in a "paused" state.
The snapshot operation being valid only if the VM has been previously
paused.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When the hypervisor crate was introduced, a few places that handled
errors were commented out in favor of unwrap, but that's bad practice.
Restore proper error handling in those places in this patch.
We cannot use from_raw_os_error anymore because it is wrapped deep under
hypervisor crate. Create new custom errors instead.
Fixes: e4dee57e81 ("arch, pci, vmm: Initial switch to the hypervisor crate")
Signed-off-by: Wei Liu <liuwe@microsoft.com>
This commit fixes some warnings introduced in the previous
hyperviosr crate PR.Removed some unused variables from arch/aarch64
module.
Signed-off-by: Muminul Islam <muislam@microsoft.com>
Start moving the vmm, arch and pci crates to being hypervisor agnostic
by using the hypervisor trait and abstractions. This is not a complete
switch and there are still some remaining KVM dependencies.
Signed-off-by: Muminul Islam <muislam@microsoft.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are two CPUID leaves for handling CPU topology, 0xb and 0x1f. The
difference between the two is that the 0x1f leaf (Extended Topology
Leaf) supports exposing multiple die packages.
Fixes: #1284
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The extended topology leaf (0x1f) also needs to have the APIC ID (which
is the KVM cpu ID) set. This mirrors the APIC ID set on the 0xb topology
leaf
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than saving the individual parts into the CpuManager save the
full struct as it now also contains the topology data.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This allows the user to optionally specify the desired CPU topology. All
parts of the topology must be specified and the product of all parts
must match the maximum vCPUs.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Its test case calls remove unconditionally. Instead of making the test
code call remove conditionally, removing the pci_support dependency
simplifies things -- that function is just a wrapper around HashMap's
remove function anyway.
Signed-off-by: Wei Liu <liuwe@microsoft.com>
Now that PCI device hotplug returns a response, the OpenAPI definition
must reflect it, describing what is expected to be received.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to provide a more comprehensive b/d/f to the user, the
serialization of PciDeviceInfo is implemented manually to control the
formatting.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This patch completes the series by connecting the dots between the HTTP
frontend and the device manager backend.
Any request to hotplug a VFIO, disk, fs, pmem, net, or vsock device will
now return a response including the device name and the place of the
device in the PCI topology.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Pass from the device manager to the calling code the information about
the PCI device that has just been hotplugged.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to provide the device name and PCI b/d/f associated with a
freshly hotplugged device, the hotplugging functions from the device
manager return a new structure called PciDeviceInfo.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
X86 and AArch64 work in different ways to shutdown a VM.
X86 exit VMM event loop through ACPI device;
AArch64 need to exit from CPU loop of a SystemEvent.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
Screened IO bus because it is not for AArch64.
Enabled Serial, RTC and Virtio devices with MMIO transport option.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
Implemented GSI allocator and system allocator for AArch64.
Renamed some layout definitions to align more code between architectures.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
In order to workaround a Linux bug that happens when we place devices at
the end of the physical address space on recent hardware (52 bits limit)
we reduce the MMIO address space by one 4k page. This way, nothing gets
allocated in the last 4k of the address space, which is negligible given
the amount of space in the address space.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The action of "vm.delete" should not report errors on non-booted
VMs. This patch also revised the "docs/api.md" to reflect the right
'Prerequisites' of different API actions, e.g. on "vm.delete" and
"vm.boot".
Fixes: #1110
Signed-off-by: Bo Chen <chen.bo@intel.com>
This removes the need to use CAP_NET_ADMIN privileges and instead the
host MAC addres is either provided by the user or alternatively it is
retrieved from the kernel.
TEST=Run cloud-hypervisor without CAP_NET_ADMIN permission and a
preconfigured tap device:
sudo ip tuntap add name tap0 mode tap
sudo ifconfig tap0 192.168.249.1 netmask 255.255.255.0 up
cargo clean
cargo build
target/debug/cloud-hypervisor --serial tty --console off --kernel ~/src/rust-hypervisor-firmware/target/target/release/hypervisor-fw --disk path=~/workloads/clear-33190-kvm.img --net tap=tap0
VM was also rebooted to check that works correctly.
Fixes: #1274
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This allows an existing TAP interface to be used without needing
CAP_NET_ADMIN permissions on the Cloud Hypervisor binary as the ioctl to
bring up the interface is avoided.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
There is a much stronger PCI dependency from vfio_pci.rs than a VFIO one
from pci/src/vfio.rs. It seems more natural to have the PCI specific
VFIO implementation in the PCI crate rather than the other way around.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now the flow of both architectures are aligned to:
1. load kernel
2. create VCPU's
3. configure system
4. start VCPU's
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
Between X86 and AArch64, there is some difference in booting a VM:
- X86_64 can setup IOAPIC before creating any VCPU.
- AArch64 have to create VCPU's before creating GIC.
The old process is:
1. load_kernel()
load kernel binary
configure system
2. activate_vcpus()
create & start VCPU's
So we need to separate "activate_vcpus" into "create_vcpus" and
"activate_vcpus" (to start vcpus only). Setup GIC and create FDT
between the 2 steps.
The new procedure is:
1. load_kernel()
load kernel binary
(X86_64) configure system
2. create VCPU's
3. (AArch64) setup GIC
4. (AArch64) configure system
5. start VCPU's
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
Instead of responding only headers with error code, we now return
complete error responses to HTTP requests with errors (e.g. undefined
endpoints and InternalSeverError).
Fixes: #472
Signed-off-by: Bo Chen <chen.bo@intel.com>
When doing self spawning the child will attempt to set the umask() again. Let
it through the seccomp rules so long as it the safe mask again.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This commit only implements the InterruptController crate on AArch64.
The device specific part for GIC is to be added.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
IOAPIC, a X86 specific interrupt controller, is referenced by device
manager and CPU manager. To work with more architectures, a common
type for all architectures is needed.
This commit introduces trait InterruptController to provide architecture
agnostic functions. Device manager and CPU manager can use it without
caring what the underlying device is.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
This is a preparing commit to build and test CH on AArch64. All building
issues were fixed, but no functionality was introduced.
For X86, the logic of code was not changed at all.
For ARM, the architecture specific part is still empty. And we applied
some tricks to workaround lint warnings. But such code will be replaced
later by other commits with real functionality.
Signed-off-by: Michael Zhao <michael.zhao@arm.com>
This config option provided very little value and instead we now enable
this feature (which then lets the guest control the cache mode)
unconditionally.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Explicit call to 'close()' is required on file descriptors allocated
from 'epoll::create()', which is missing for the 'EpollContext' and
'VringWorker'. This patch enforces to close the file descriptors by
reusing the Drop trait of the 'File' struct.
Signed-off-by: Bo Chen <chen.bo@intel.com>
Add a new "host_mac" parameter to "--net" and "--net-backend" and use
this to set the MAC address on the tap interface. If no address is given
one is randomly assigned and is stored in the config.
Support for vhost-user-net self spawning was also included.
Fixes: #1177
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The clock_nanosleep system call needs to be whitelisted since the commit
12e00c0f45 introduced the use of a sleep()
function. Without this patch, we can see an error when the VM is paused
or killed.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Like the actions that don't take data such as "pause" or "resume" use a
common handler implementation to remove duplicated code for handling
simple endpoints like the hotplug ones.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Many of the API requests take a similar form with a single data item
(i.e. config for a device hotplug) expand the VmAction enum to handle
those actions and a single function to dispatch those API events.
For now port the existing helper functions to use this new API. In the
future the HTTP layer can create the VmAction directly avoiding the
extra layer of indirection.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than save the save a function pointer and use that instead the
underlying action. This is useful for two reasons:
1. We can ensure that we generate HttpErrors in the same way as the
other endpoints where API error variant should be determined by the
request being made not the underlying error.
2. It can be extended to handle other generic actions where the function
prototype differs slightly.
As result of this refactoring it was found that the "vm.delete" endpoint
was not connected so address that issue.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Extend the EndpointHandler trait to include automatic support for
handling PUT requests. This will allow the removal of lots of duplicated
code in the following commit from the API handling code.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The ch branch has been rebased to incorporate the latest upstream code
requiring a small change to the unit tests.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
By passing a reference of the DeviceTree to the AddressManager, we can
now update the DeviceTree whenever a PCI BAR is reprogrammed. This is
mandatory to maintain the correct resources information related to each
virtio-pci device, which will ensure correct information will be stored
upon VM snapshot.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
We want to be able to share the same DeviceTree across multiple threads,
particularly to handle the use case where PCI BAR reprogramming might
need to update the tree while from another thread a new device is being
added to the tree.
That's why this patch moves the DeviceTree instance into an Arc<Mutex<>>
so that we can later share a reference of the same mutable tree with the
AddressManager responsible for handling PCI BAR reprogramming.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
By using the vector of resources provided by the DeviceNode, the device
manager can store the information related to PCI BARs from a virtio-pci
device. Based on this, and upon VM restoration, the device manager can
restore the BARs in the expected location in the guest address space.
One thing to note is that we only need to provide the VirtioPciDevice
with the configuration BAR (BAR 0) since the SHaredMemory BAR info comes
from the virtio device directly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on the new field "pci_bdf", a virtio-pci device can be restored at
the same place on the PCI bus it was located before the VM snapshot.
This ensures consistent placement on the PCI bus, based on the stored
information related to each device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
We need a way to store the information about where a PCI device was
placed on the PCI bus before the VM was snapshotted. The way to do this
is by adding an extra field to the DeviceNode structure.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Switch to using the recently added OptionParser in the code that parses
the block backend.
Fixes: #1092
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Switch to using the recently added OptionParser in the code that parses
the network backend.
Whilst doing this also update the net-backend syntax to use "sock"
rather than socket.
Fixes: #1092
Partially fixes: #1091
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
To avoid a race condition where the signal might "miss" the KVM_RUN
ioctl() instead reapeatedly try sending a signal until the vCPU run is
interrupted (as indicated by setting a new per vCPU atomic.)
It important to also clear this atomic when coming out of a paused
state.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
To ensure that the DeviceManager threads (such as those used for virtio
devices) are cleaned up it is necessary to unpark them so that they get
cleanly terminated as part of the shutdown.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
After setting the kill signal flag for the vCPU thread release the pause
flag and unpark the threads. This ensures that that the vCPU thread will
wake up and check the kill signal flag if the VM is paused.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Rather than immediately entering the vCPU run() code check if the kill
signal is set. This allows paused VMs to be shutdown.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This module will be dedicated to DeviceNode and DeviceTree definitions
along with some dedicated unit tests.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This iterator will let the VMM enumerate the resources associated
with the DeviceManager, allowing for introspection.
Moreover, by implementing a double ended iterator, we can get the
hierarchy from the leaves to the root of the tree, which is very
helpful in the context of restoring the devices in the right order.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that the device tree fully replaced the need for a dedicated list of
migratable devices, this commit cleans up the codebase by removing it
from the DeviceManager.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This commit switches from migratable_devices to device_tree in order to
restore devices exclusively based on the device tree.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This commit adds an extra field to the DeviceNode so that the structure
can hold a Migratable device. The long term plan is to be able to remove
the dedicated table of migratable devices, but instead rely only on the
device tree.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to hide the complexity chosen for the device tree stored in
the DeviceManager, we introduce a new DeviceTree structure.
For now, this structure is a simple passthrough of a HashMap, but it can
be extended to handle some DeviceTree specific operations.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This device has a dedicated memory region in the guest address space,
which means in case of snapshot/restore, it must be restored in the
exact same location it was during the snapshot.
That's through the resources that we can describe the location of this
extra memory region, allowing the device for correct restoring.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This device has a dedicated memory region in the guest address space,
which means in case of snapshot/restore, it must be restored in the
exact same location it was during the snapshot.
That's through the resources that we can describe the location of this
extra memory region, allowing the device for correct restoring.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on the device tree, retrieve the resources associated with a
virtio-mmio device to restore it at the right location in guest address
space. Also, the IRQ number is correctly restored.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Instead of splitting the MMIO allocation and the device creation into
separate functions for virtio-mmio devices, it's is easier to move
everything into the same function as we'll be able to gather resources
in the same place for the same device.
These resources will be stored in the device tree in a follow up patch.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In case the VM is created from scratch, the devices should be created
after the DeviceManager has been created. But this should not affect the
restore codepath, as in this case the devices should be created as part
of the restore() function.
It's necessary to perform this differentiation as the restore must go
through the following steps:
- Create the DeviceManager
- Restore the DeviceManager with the right state
- Create the devices based on the restored DeviceManager's device tree
- Restore each device based on the restored DeviceManager's device tree
That's why this patch leverages the recent split of the DeviceManager's
creation to achieve what's needed.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This commit performs the split of the DeviceManager's creation into two
separate functions by moving anything related to device's creation after
the DeviceManager structure has been initialized.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Based on the device tree, we now ensure the restore can be done in the
right order, as it will respect the dependencies between nodes.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The DeviceManager itself must be snapshotted in order to store the
information regarding the devices associated with it, which effectively
means we need to store the device tree.
The mechanics to snapshot and restore the DeviceManagerState are added
to the existing snapshot() and restore() implementations.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The DeviceManager now creates a tree of devices in order to store the
resources associated with each device, but also to track dependencies
between devices.
This is a key part for proper introspection, but also to support
snapshot and restore correctly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
It's not possible to call UnixListener::Bind() on an existing file so
unlink the created socket when shutting down the Vsock device.
This will allow the VM to be rebooted with a vsock device.
Fixes: #1083
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Generate an error during validation if an attempt it made to place a
device behind an IOMMU or using a VFIO device when not using PCI.
Fixes: #751
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Let's put an underscore "_" in front of each device name to identify
when it has been set internally.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The virtio-console was not added to the list of Migratable devices,
which is fixed from this patch.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
It is based off the name from the virtio device attached to this
transport layer.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
It is based off the name from the virtio device attached to this
transport layer.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Because we know we will need every virtio device to be identified with a
unique id, we can simplify the code by making the identifier mandatory.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Even in the context of "mmio" feature, we need the next device name to
be generated as we need to identify virtio-mmio devices to support
snapshot and restore functionalities.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This will be later used to identify each device used by the VM in order
to perform introspection and snapshot/restore properly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This will be later used to identify each device used by the VM in order
to perform introspection and snapshot/restore properly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This will be later used to identify each device used by the VM in order
to perform introspection and snapshot/restore properly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This will be later used to identify each device used by the VM in order
to perform introspection and snapshot/restore properly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This will be later used to identify each device used by the VM in order
to perform introspection and snapshot/restore properly.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
If the virtio-console device is supposed to be placed behind the virtual
IOMMU, this must be explicitly propagated through the code.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
If the virtio-rng device is supposed to be placed behind the virtual
IOMMU, this must be explicitly propagated through the code.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
If the virtio-vsock device is supposed to be placed behind the virtual
IOMMU, this must be explicitly propagated through the code.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that all virtio devices are assigned with identifiers, they could
all be removed from the VM. This is not something that we want to allow
because it does not make sense for some devices. That's why based on the
device type, we remove the device or we return an error to the user.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
By giving the devices ids this effectively enables the removal of the
device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The parameters regarding the attachment to the virtio-iommu device was
not propagated correclty, and any modification to the configuration was
not stored back into it.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
It's possible to have multiple vsock devices so in preparation for
hotplug/unplug it is important to be able to have a unique identifier
for each device.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
If the current state is paused that means most of the handles got killed by pthread_kill
We need to unpark those threads to make the shutdown worked. Otherwise
The shutdown API hangs and the API is not responding afterwards. So
before the shutdown call we need to resume the VM make it succeed.
Fixes: #817
Signed-off-by: Muminul Islam <muislam@microsoft.com>
If a size is specified use it (in particular this is required if the
destination is a directory) otherwise seek in the file to get the size
of the file.
Add a new check that the size is a multiple of 2MiB otherwise the kernel
will reject it.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Check that if any device using vhost-user (net & disk with
vhost_user=true) or virtio-fs is enabled then check shared memory is
also enabled.
Fixes: #848
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The new 'shared' and 'hugepages' controls aim to replace the 'file'
option in MemoryConfig. This patch also updated all related integration
tests to use the new controls (instead of providing explicit paths to
"/dev/shm" or "/dev/hugepages").
Fixes: #1011
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Signed-off-by: Bo Chen <chen.bo@intel.com>
Replace alignment calculation of start address with functionally
equivalent version that does not assume that the block size is a power
of two.
Signed-off-by: Martin Xu <martin.xu@intel.com>
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When a virtio device is dynamically removed from the VM through the
hot-unplug mechanism, every mapping associated with it must be properly
removed.
Based on the previous patches letting a VirtioDevice expose the list of
userspace mappings associated with it, this patch can now remove all the
KVM userspace memory regions through the MemoryManager.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The same way we added a helper for creating userspace memory mappings
from the MemoryManager, this patch adds a new helper to remove some
previously added mappings.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When hot-unplugging the virtio-pmem from the VM, we don't remove the
associated userspace mapping. This patch will let us fix this in a
following patch. For now, it simply adapts the code so that the Pmem
device knows about the mapping associated with it. By knowing about it,
it can expose it to the caller through the new userspace_mappings()
function.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The hotplugged virtio devices were not added to the list of virtio
devices from the DeviceManager. This patch fixes it, as it was causing
hotplugged virtio-fs devices from not supporting memory hotplug, since
they were never getting the update as they were not part of the list of
virtio devices held by the DeviceManager.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Adds DeviceManager method `make_virtio_fs_device` which creates a single
device, and modifies `make_virtio_fs_devices` to use this method.
Implements the new `vm.add-fs route`.
Signed-off-by: Dean Sheather <dean@coder.com>
Currently unimplemented. Once implemented, this API will allow for
creating virtio-fs devices in the VM after it has booted.
Signed-off-by: Dean Sheather <dean@coder.com>
In the context of the shared memory region used by virtio-fs in order to
support DAX feature, the shared region is exposed as a dedicated PCI
BAR, and it is backed by a KVM userspace mapping.
Upon BAR remapping, the BAR is moved to a different location in the
guest address space, and the KVM mapping must be updated accordingly.
Additionally, we need the VirtioDevice to report the updated guest
address through the shared memory region returned by get_shm_regions().
That's why a new setter is added to the VirtioDevice trait, so that
after the mapping has been updated for KVM, we can tell the VirtioDevice
the new guest address the shared region is located at.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The order the elements are pushed into the list is important to restore
them in the right order. This is particularly important for MmioDevice
(or VirtioPciDevice) and their VirtioDevice counterpart.
A device must be fully ready before its associated transport layer
management can trigger its restoration, which will end up activating the
device in most cases.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
OVMF and other standard firmwares use I/O port 0x402 as a simple debug
port by writing ASCII characters to it. This is gated under a feature
that is not enabled by default.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
We now support assigning device ids for VFIO and virtio-pci devices so
this error can be generalised.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Extend the eject_device() method on DeviceManager to also support
virtio-pci devices being unplugged.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In order to support hotplugging there is a map of human readable device
id to PCI BDF map.
As the device id is part of the specific device configuration (e.g.
NetConfig) it is necessary to return the id through from the helper
functions that create the devices through to the functions that add
those devices to the bus. This necessitates changing a great deal of
function prototypes but otherwise has little impact.
Currently only if an id is supplied by the user as part of the device
configuration is it populated into this map. A later commit will
populate with an autogenerated name where none is supplied by the user.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Now that ownership of the memory regions used for the virtio-pmem and
vhost-user-fs devices have been moved into those devices it is no longer
necessary to track them inside DeviceManager.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Move the release of the managed memory region from the DeviceManager to
the vhost-user-fs device. This ensures that the memory will be freed when
the device is unplugged which will lead to it being Drop()ed.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Move the release of the managed memory region from the DeviceManager to
the virtio-pmem device. This ensures that the memory will be freed when
the device is unplugged which will lead to it being Drop()ed.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
While testing self spawned vhost-user backends, it appeared that the
backend was aborting due to a missing system call in the seccomp
filters. mremap() was the culprit and this patch simply adds it to the
whitelist.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This should make it a pointer in the Go generated code so that it will
be ommitted and thus not populated with an unhelpful default value.
Fixes: #1015
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This ensures that the field is filled with None when it is not specified
as part of the deserialisation step.
Fixes: #1015
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
We can now allow guests that specify an initramfs to boot
using the PVH boot protocol.
Signed-off-by: Alejandro Jimenez <alejandro.j.jimenez@oracle.com>
This allows the validation of this requirement for both command line
booted VMs and those booted via the API.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This allows the validation of this requirement for both command line
booted VMs and those booted via the API.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Replace the existing VmConfig::valid() check with a call into
.validate() as part of earlier config setup or boot API checks.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When performing an API boot validate the configuration. For now only
some very basic validation is performed but in subsequent commits
the validation will be extended.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The configuration comes from a variety of places (commandline, REST API
and restore) however some validation was only happening on the command
line parsing path. Therefore introduce a new ability to validate the
configuration before proceeding so that this can be used for commandline
and API boots.
For now move just the console and serial output mode validation under
the new validation API.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Making sure the OpenAPI definition is up to date with newly added
structure and parameters to support VM restoration.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that the restore path uses RestoreConfig structure, we add a new
parameter called "prefault" to it. This will give the user the ability
to populate the pages corresponding to the mapped regions backed by the
snapshotted memory files.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The goal here is to move the restore parameters into a dedicated
structure that can be reused from the entire codebase, making the
addition or removal of a parameter easier.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
When CoW can be used, the VM restoration time is reduced, but the pages
are not populated. This can lead to some slowness from the guest when
accessing these pages.
Depending on the use case, we might prefer a slower boot time for better
performances from guest runtime. The way to achieve this is to prefault
the pages in this case, using the MAP_POPULATE flag along with CoW.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This patch extends the previous behavior on the restore codepath.
Instead of copying the memory regions content from the snapshot files
into the new memory regions, the VMM will use the snapshot region files
as the backing files behind each mapped region. This is done in order to
reduce the time for the VM to be restored.
When the source VM has been initially started with a backing file, this
means it has been mapped with the MAP_SHARED flag. For this case, we
cannot use the CoW trick to speed up the VM restore path and we simply
fallback onto the copy of the memory regions content.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Whenever a MemoryManager is restored from a snapshot, the memory regions
associated with it might need to directly back the mapped memory for
increased performances. If that's the case, a list of external regions
is provided and the MemoryManager should simply ignore what's coming
from the MemoryConfig.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Now that we can choose specific mmap flags for the guest RAM, we create
a new parameter "copy_on_write" meaning that the memory mappings backed
by a file should be performed with MAP_PRIVATE instead of MAP_SHARED.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to anticipate the need for special mmap flags when memory
mapping the guest RAM, we need to switch from from_file() wrapper to
build() wrapper.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
A few KVM ioctls were missing in order to perform both snapshot and
restore while keeping seccomp enabled.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This connects the dots together, making the request from the user reach
the actual implementation for restoring the VM.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This connects the dots together, making the request from the user reach
the actual implementation for snapshotting the VM.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
The MemoryManager is somehow a special case, as its restore() function
was not implemented as part of the Snapshottable trait. Instead, and
because restoring memory regions rely both on vm.json and every memory
region snapshot file, the memory manager is restored at creation time.
This makes the restore path slightly different from CpuManager, Vcpu,
DeviceManager and Vm, but achieve the correct restoration of the
MemoryManager along with its memory regions filled with the correct
content.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is only implementing the send() function in order to store all Vm
states into a file.
This needs to be extended for live migration, by adding more transport
methods, and also the recv() function must be implemented.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
By aggregating snapshots from the CpuManager, the MemoryManager and the
DeviceManager, Vm implements the snapshot() function from the
Snapshottable trait.
And by restoring snapshots from the CpuManager, the MemoryManager and
the DeviceManager, Vm implements the restore() function from the
Snapshottable trait.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
This implements the send() function of the Transportable trait, so that
the guest memory regions can be saved into one file per region.
This will need to be extended for live migration, as it will require
other transport methods and the recv() function will need to be
implemented too.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to snapshot the content of the guest RAM, the MemoryManager
must implement the Snapshottable trait.
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Implement the Snapshottable trait for Vcpu, and then implements it for
CpuManager. Note that CpuManager goes through the Snapshottable
implementation of Vcpu for every vCPU in order to implement the
Snapshottable trait for itself.
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Anticipating the need for a slightly different function for restoring
vCPUs, this patch factorizes most of the vCPU creation, so that it can
be reused for migration purposes.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
These two new helpers will be useful to capture a vCPU state and being
able to restore it at a later time.
Signed-off-by: Cathy Zhang <cathy.zhang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In anticipation for the CpuManager to aggregate all Vcpu snapshots
together, this change makes sure the CpuManager has a handle onto
every vCPU.
Signed-off-by: Cathy Zhang <cathy.zhang@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Based on the list of Migratable devices stored by the DeviceManager, the
DeviceManager can implement the Snapshottable trait by aggregating all
devices snapshots together.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Serial and Ioapic both implement the Migratable trait, hence the
DeviceManager can store them in the list of Migratable devices.
Signed-off-by: Yi Sun <yi.y.sun@linux.intel.com>
The parse_size helper function can now be consolidated into the
ByteSized FromStr implementation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Now all parsing code makes use of the Toggle and it's FromStr support
move the helper function into the from_str() implementation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The integration tests and documentation make use of empty value strings
like "--net tap=" accept them but return None so that the default value
will be used as expected.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This simplifies the parsing of the option by using OptionParser along
with its automatic conversion behaviour.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Byte sizes are quantities ending in "K", "M", "G" and by implementing
this type with a FromStr implementation the values can be converted
using .parse().
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Before porting over to OptionParser add a unit test to validate the
current memory parsing code. This showed up a bug where the "size=" was
always required. Temporarily resolve this by assigning the string a
default value which will later be replaced when the code is refactored.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This will be used to simplify and consolidate much of the parsing code
used for command line parameters.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
