This removes the need to use CAP_NET_ADMIN privileges and instead the
host MAC addres is either provided by the user or alternatively it is
retrieved from the kernel.
TEST=Run cloud-hypervisor without CAP_NET_ADMIN permission and a
preconfigured tap device:
sudo ip tuntap add name tap0 mode tap
sudo ifconfig tap0 192.168.249.1 netmask 255.255.255.0 up
cargo clean
cargo build
target/debug/cloud-hypervisor --serial tty --console off --kernel ~/src/rust-hypervisor-firmware/target/target/release/hypervisor-fw --disk path=~/workloads/clear-33190-kvm.img --net tap=tap0
VM was also rebooted to check that works correctly.
Fixes: #1274
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The API has change to use generic GuestMemory trait:
pub fn get_host_address_range<M: GuestMemory>(
mem: &M,
addr: GuestAddress,
size: usize,
) -> Option<*mut u8> {
Signed-off-by: Arron Wang <arron.wang@intel.com>
If VIRTIO_RING_F_EVENT_IDX is negotiated only generate suppress
interrupts if the guest has asked us to do so.
Fixes: #788
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
In some situations it is seen that the first interrupt sent to the guest
is lost upon a restore (due to the tap worker being awake ahead of the
vPUs).
This causes problems with VIRTIO_RING_F_EVENT_IDX interrupt suppression
as the guest will not be interrupted again in order to mitigate this we
always interrupt the guest until the device itself has been signalled by
the guest.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This requires exposing the struct members and also using Option<..>
types for the main epoll fd and the memory as they are initialised later
in vhost-user-net.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Split handling of behaviour that is independent of the device itself so
that it can be reused in the vhost-user-net device.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Split out functions that work just on the TAP device and queues. Whilst
doing so also improve the error handling to return Results rather than
drop errors.
This change also addresses a bug where the TAP event suppression could
ineffectual because it was being enabled immediately after it may have
been disabled:
resume_rx -> rx_single_frame -> unregister_listener -> resume_rx ->
register_listener.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This config option provided very little value and instead we now enable
this feature (which then lets the guest control the cache mode)
unconditionally.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Correctly implement the virtio specification by setting the writeback
field on the request based on the algorithm in the spec.
TEST=Boot with hypervisor-firmware with CH in verbose mode. See info
level messages saying cache mode is writethrough in firmware (no support
for flush or WCE). Once in the Linux kernel see messages that mode is
writeback.
Fixes: #1216Fixes: #680
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
When this is set to false the write needs to be followed by a flush on
the underlying disk (leading to a fsync()).
The default behaviour is not changed with this change.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Move the method that is used to decide whether the guest should be
signalled into the Queue implementation from vm-virtio. This removes
duplicated code between vhost_user_backend and the vm-virtio block
implementation.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
The implementation of this virtio block (and vhost-user block) command
called a function that was a no-op on Linux. Use the same function as
virtio-pmem to ensure that data is not lost when the guest asks for it
to be flused to disk.
Fixes: #399
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
For both virtio-mmio and virtio-pci transport layers, we were setting
every field from the saved snapshot during a restore. This is a problem
when we don't want to override specific fields such as iommu_mapping_cb
because the saved snapshot doesn't contain the appropriate information.
That's why this commit sets only the appropriate field from the saved
snapshot during a restore.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Provide implementation for both snapshot() and restore() methods from
the Snapshottable trait, so that we can snapshot and restore a VM with
devices attached to a virtual IOMMU.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
According to the virtio spec the guest should always be interrupted when
"used" descriptors are returned from the device to the driver. However
this was not the case for the TX queue in either the virtio-net
implementation or the vhost-user-net implementation.
This would have meant that the guest could end up with a reduced TX
throughput as it would not know that the packets had been dispatched via
the VMM.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add a new "host_mac" parameter to "--net" and "--net-backend" and use
this to set the MAC address on the tap interface. If no address is given
one is randomly assigned and is stored in the config.
Support for vhost-user-net self spawning was also included.
Fixes: #1177
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
From a VirtioPciDevice perspective, there are two types of BARs, either
the virtio configuration BAR or the SHaredMemory BAR.
The SHaredMemory BAR address comes from the virtio device directly as
the memory region had been previously allocated when the virtio device
has been created. So for this BAR, there's nothing to do when restoring
a VM, since the associated virtio device is already restored with the
appropriate resources, hence the BAR will already be at the right
address.
The remaining configuration BAR is different, as we usually get its
address from the SystemAllocator. This means in case we restore a VM,
we must provide this value, bypassing the allocator. This is what this
commit takes care of, by letting the caller set the base address for the
configuration BAR prior to allocating the BARs.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This gives Cloud-Hypervisor the possibility to snapshot and restore a
VM running with virtio-pci devices attached to it.
The VirtioPciDevice snapshot contains a vector of sub-snapshots to store
and restore information related to MsixConfig, VirtioPciCommonConfig and
PciConfiguration structures, along with snapshot data related to
VirtioPciDevice itself.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This structure contains all the virtio generic information, and as part
of restoring a VM with virtio-pci devices, it is important to restore
these values to ensure the device's proper functioning.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Upon a virtio reset, the driver expects that available and used indexes
will be reset to 0. That's why we need to reset these values from the
VMM for any virtio device that might get reset.
This issue was not detected before because the Vec<Queue> maintained
through VirtioPciDevice or MmioDevice was never updated from the virtio
device thread after the device had been actived. For this reason, upon
reset, both available and used indexes were already at the value 0.
The issue arose when trying to reset a device after the VM was restored.
That's because during the restore, each queue is assigned with the right
available and used indexes before it is passed to the device through the
activate function. And that's why upon reset, each queue was still
assigned with these indexes while it should have been reset to 0.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
All our virtio devices support to be reset, but the virtio-mmio
transport layer was not implemented for it. This patch fixes this
lack of support.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
It's not possible to call UnixListener::Bind() on an existing file so
unlink the created socket when shutting down the Vsock device.
This will allow the VM to be rebooted with a vsock device.
Fixes: #1083
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
It is based off the name from the virtio device attached to this
transport layer.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
It is based off the name from the virtio device attached to this
transport layer.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This identifier is chosen from the DeviceManager so that it will manage
all identifiers across the VM, which will ensure uniqueness.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
