meson: adjust our documentation to mention meson instead of autoconf

Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Neal Gompa <ngompa13@gmail.com>

CONTRIBUTING.rst

@@ -12,13 +12,12 @@ your git clone run:
 
 ::
 
-   $ mkdir build && cd build
+   $ meson build
-   $ ../autogen.sh
+   $ ninja -C build
-   $ make
 
 You'll find the freshly-built document in ``docs/contribute.html``.
 
-If ``configure`` fails because of missing dependencies, you can set
+If ``meson setup`` fails because of missing dependencies, you can set
 up your system by calling
 
 ::
@@ -39,7 +38,7 @@ to run
 
 ::
 
-   $ sudo dnf install gcc make libtool autoconf automake rpm-build
+   $ sudo dnf install gcc make ninja-build rpm-build
 
 You might still be missing some dependencies if your distribution is
 shipping an old libvirt version, but that will get you much closer to

docs/advanced-tests.rst

@@ -6,8 +6,7 @@ The basic requirement before submitting changes to libvirt is that
 
 ::
 
-  $ make check
+  $ ninja test
-  $ make syntax-check
 
 succeed after each commit.
 
@@ -17,7 +16,7 @@ by running
 
 ::
 
-  $ make -C tests valgrind
+  $ meson test --setup valgrind
 
 `Valgrind <http://valgrind.org/>`__ is a test that checks for
 memory management issues, such as leaks or use of uninitialized
@@ -27,13 +26,13 @@ Some tests are skipped by default in a development environment,
 based on the time they take in comparison to the likelihood
 that those tests will turn up problems during incremental
 builds. These tests default to being run when building from a
-tarball or with the configure option --enable-expensive-tests;
+tarball or with the configure option -Dexpensive_tests=enabled;
 you can also force a one-time toggle of these tests by setting
 VIR_TEST_EXPENSIVE to 0 or 1 at make time, as in:
 
 ::
 
-  $ make check VIR_TEST_EXPENSIVE=1
+  $ VIR_TEST_EXPENSIVE=1 ninja test
 
 If you encounter any failing tests, the VIR_TEST_DEBUG
 environment variable may provide extra information to debug the
@@ -42,8 +41,8 @@ amounts of information:
 
 ::
 
-  $ VIR_TEST_DEBUG=1 make check    (or)
+  $ VIR_TEST_DEBUG=1 ninja test    (or)
-  $ VIR_TEST_DEBUG=2 make check
+  $ VIR_TEST_DEBUG=2 ninja test
 
 When debugging failures during development, it is possible to
 focus in on just the failing subtests by using VIR_TEST_RANGE.

docs/best-practices.rst

@@ -25,9 +25,8 @@ with minimal back-and-forth.
    self-contained if possible, with an explanation of each patch
    and an explanation of how the sequence of patches fits
    together. Moreover, please keep in mind that it's required to
-   be able to compile cleanly (**including**
+   be able to compile cleanly (**including** ``ninja test``) after
-   ``make check`` and ``make syntax-check``) after each
+   each patch. A feature does not have to work until the end of a
-   patch. A feature does not have to work until the end of a
    series, but intermediate patches must compile and not cause
    test-suite failures (this is to preserve the usefulness of
    ``git bisect``, among other things).

docs/committer-guidelines.rst

@@ -12,8 +12,8 @@ objection on the list it should be good to go. If the patch
 touches a part of the code where you're not the main maintainer,
 or where you do not have a very clear idea of how things work,
 it's better to wait for a more authoritative feedback though.
-Before committing, please also rebuild locally, run 'make check
+Before committing, please also rebuild locally, run 'ninja test',
-syntax-check', and make sure you don't raise errors.
+and make sure you don't raise errors.
 
 An exception to 'review and approval on the list first' is fixing
 failures to build:
@@ -21,11 +21,10 @@ failures to build:
 -  if a recently committed patch breaks compilation on a platform
    or for a given driver, then it's fine to commit a minimal fix
    directly without getting the review feedback first
--  if make check or make syntax-check breaks, if there is an
+-  if ninja test breaks, if there is an obvious fix, it's fine to
-   obvious fix, it's fine to commit immediately. The patch should
+   commit immediately. The patch should still be sent to the list
-   still be sent to the list (or tell what the fix was if
+   (or tell what the fix was if trivial), and 'ninja test' should
-   trivial), and 'make check syntax-check' should pass too, before
+   pass too, before committing anything
-   committing anything
 -  fixes for documentation and code comments can be managed in the
    same way, but still make sure they get reviewed if non-trivial.
 -  (ir)regular pulls from other repositories or automated updates,

docs/compiling.html.in

@@ -9,28 +9,26 @@
     <h2><a id="compiling">Compiling a release tarball</a></h2>
 
     <p>
-      libvirt uses the standard configure/make/install steps and mandates
+      libvirt uses the standard setup/build/install steps and mandates
       that the build directory is different that the source directory:
     </p>
 
     <pre>
 $ xz -c libvirt-x.x.x.tar.xz | tar xvf -
 $ cd libvirt-x.x.x
-$ mkdir build &amp;&amp; cd build
+$ meson build</pre>
-$ ../configure</pre>
 
     <p>
-      The <i>configure</i> script can be given options to change its default
+      The <i>meson</i> script can be given options to change its default
       behaviour.
     </p>
 
     <p>
-      To get the complete list of the options it can take, pass it the
+      To get the complete list of the options run the following command:
-      <i>--help</i> option like this:
     </p>
 
     <pre>
-$ ../configure <i>--help</i></pre>
+$ meson configure</pre>
 
     <p>
       When you have determined which options you want to use (if any),
@@ -38,7 +36,7 @@ $ ../configure <i>--help</i></pre>
     </p>
 
     <p>
-      Note the use of <b>sudo</b> with the <i>make install</i> command
+      Note the use of <b>sudo</b> with the <i>ninja install</i> command
       below.  Using sudo is only required when installing to a location your
       user does not have write access to.  Installing to a system location
       is a good example of this.
@@ -46,14 +44,14 @@ $ ../configure <i>--help</i></pre>
 
     <p>
       If you are installing to a location that your user <i>does</i> have write
-      access to, then you can instead run the <i>make install</i> command
+      access to, then you can instead run the <i>ninja install</i> command
       without putting <b>sudo</b> before it.
     </p>
 
     <pre>
-$ ../configure <i>[possible options]</i>
+$ meson build <i>[possible options]</i>
-$ make
+$ ninja -C build
-$ <b>sudo</b> <i>make install</i></pre>
+$ <b>sudo</b> <i>ninja -C build install</i></pre>
 
     <p>
       At this point you <b>may</b> have to run ldconfig or a similar utility
@@ -63,12 +61,10 @@ $ <b>sudo</b> <i>make install</i></pre>
     <h2><a id="building">Building from a GIT checkout</a></h2>
 
     <p>
-      The libvirt build process uses GNU autotools, so after obtaining a
+      The libvirt build process uses Meson build system. By default when
-      checkout it is necessary to generate the configure script and Makefile.in
+      the <code>meson</code> is run from within a GIT checkout, it
-      templates using the <code>autogen.sh</code> command. By default when
-      the <code>configure</code> script is run from within a GIT checkout, it
       will turn on -Werror for builds. This can be disabled with
-      --disable-werror, but this is not recommended.
+      --werror=false, but this is not recommended.
     </p>
 
     <p>To build &amp; install libvirt to your home
@@ -76,10 +72,9 @@ $ <b>sudo</b> <i>make install</i></pre>
     </p>
 
     <pre>
-$ mkdir build &amp;&amp; cd build
+$ meson build --prefix=$HOME/usr
-$ ../autogen.sh --prefix=$HOME/usr
+$ ninja -C build
-$ make
+$ <b>sudo</b> ninja -C build install</pre>
-$ <b>sudo</b> make install</pre>
 
     <p>
       Be aware though, that binaries built with a custom prefix will not
@@ -89,9 +84,8 @@ $ <b>sudo</b> make install</pre>
     </p>
 
     <pre>
-$ mkdir build &amp;&amp; cd build
+$ meson build -Dsystem=true
-$ ../autogen.sh --system
+$ ninja -C build
-$ make
     </pre>
 
     <p>

docs/hacking.rst

@@ -30,8 +30,7 @@ changes. That is:
 
 ::
 
-  $ make check
+  $ ninja test
-  $ make syntax-check
 
 These tests help making sure that your changes don't introduce
 regressions in libvirt, as well as validating that any new code

docs/strategy.html.in

@@ -22,13 +22,12 @@
         in the C language.</dd>
       <dt>Python</dt>
       <dd>Various supporting build/test scripts are written in Python, with
-        compatibility for Python 2 and 3.</dd>
+        compatibility for Python 3.</dd>
       <dt>Perl</dt>
       <dd>Various supporting build/test scripts are written in Perl. It is
         also used for many syntax-check inline rules</dd>
       <dt>Shell</dt>
-      <dd><code>configure</code>, generated by autoconf, is a shell script.
+      <dd>Shell is used for some simple build/test scripts. At runtime
-        Shell is also used for some simple build/test scripts. At runtime
         libvirt avoids shell except when using SSH tunnels to a remote
         host</dd>
       <dt>XSLT</dt>
@@ -38,14 +37,10 @@
       <dt>HTML</dt>
       <dd>The website documentation is all written in plain HTML. Some HTML
         is also auto-generated for API documentation</dd>
-      <dt>M4</dt>
+      <dt>Meson</dt>
-      <dd>The autoconf <code>configure</code> script uses a large number of
+      <dd>The core build system uses the new Meson build system</dd>
-        M4 macros to generate its content</dd>
       <dt>make</dt>
-      <dd>The core build system uses the traditional GNU make recipes</dd>
+      <dd>The syntax-check uses make recipes</dd>
-      <dt>automake</dt>
-      <dd>The make recipes use automake's language extensions which are
-        then turned into regular make rules</dd>
       <dt>awk/sed</dt>
       <dd>A number of the syntax-check inline rules involve use of awk/sed
         scripts</dd>
@@ -58,8 +53,8 @@
       The wide range of languages used present a knowledge burden for
       developers involved in libvirt, especially when there are multiple
       languages all used in the same problem spaces. This is most notable
-      in the build system which uses a combination of shell, M4, make,
+      in the build system which uses a combination of Meson, shell, awk,
-      automake, awk, sed, Perl and Python, with debugging requiring
+      sed, Perl and Python, with debugging requiring
       understanding of the interactions between many languages. The
       popularity of Perl has declined, while Python has become
       more popular. This directly influences the amount and quality of
@@ -119,14 +114,6 @@
       code.
     </p>
 
-    <p>
-      The Meson build system is written in Python 3. This directly informs the
-      choice of Python 3 as the language for all supporting build scripts,
-      re-inforcing the other benefits of Python over Perl, Shell, M4,
-      automake, etc. There is no intention to support Python 2 given Meson's
-      requirement for Python 3.
-    </p>
-
     <p>
       Using the RST format for documentation allows for the use of XSLT to be
       eliminated from the build process. RST and the Sphinx toolkit are widely

docs/windows.html.in

@@ -180,16 +180,14 @@
     </p>
 
 <pre>
-mkdir build &amp;&amp; cd build
+meson build \
-../configure \
+  -Dsasl=disabled \
-  --without-sasl \
+  -Dpolkit=disabled \
-  --without-polkit \
+  -Ddriver_libxl=disabled \
-  --without-python \
+  -Ddriver_qemu=disabled \
-  --without-libxl \
+  -Ddriver_lxc=disabled \
-  --without-qemu \
+  -Ddriver_openvz=disabled \
-  --without-lxc \
+  -Ddriver_libvirtd=disabled
-  --without-openvz \
-  --without-libvirtd
 </pre>
 
   </body>