diff --git a/docs/manpages/virt-qemu-sev-validate.rst b/docs/manpages/virt-qemu-sev-validate.rst index 24cdbb6d92..f5f928603a 100644 --- a/docs/manpages/virt-qemu-sev-validate.rst +++ b/docs/manpages/virt-qemu-sev-validate.rst @@ -456,6 +456,122 @@ inject a disk password on success: --domain fedora34x86_64 \ --disk-password passwd.txt +COMMON MISTAKES CHECKLIST +========================= + +The complexity of configuring a guest and validating its boot measurement +means it is very likely to see the failure:: + + ERROR: Measurement does not match, VM is not trustworthy + +This error message assumes the worst, but in most cases will failure will be +a result of either mis-configuring the guest, or passing the wrong information +when trying to validate it. The following information is a guide for what +items to check in order to stand the best chance of diagnosing the problem + +* Check the VM configuration for the DH certificate and session + blob in the libvirt guest XML. + + The content for these fields should be in base64 format, which is + what ``sevctl session`` generates. Other tools may generate the files + in binary format, so ensure it has been correctly converted to base64. + +* Check the VM configuration policy value matches the session blob + + The ```` value in libvirt guest XML has to match the value + passed to the ``sevctl session`` command. If this is mismatched + then the guest will not even start, and QEMU will show an error + such as:: + + sev_launch_start: LAUNCH_START ret=1 fw_error=11 'Bad measurement' + +* Check the correct TIK/TEK keypair are passed + + The TIK/TEK keypair are uniquely tied to each DH cert and session + blob. Make sure that the TIK/TEK keypair passed to this program + the ones matched to the DH cert and session blob configured for + the libvirt guest XML. This is one of the most common mistakes. + Further ensure that the TIK and TEK files are not swapped. + +* Check the firmware binary matches the one used to boot + + The firmware binary content is part of the data covered by the + launch measurement. Ensure that the firmware binary passed to + this program matches the one used to launch the guest. The + hypervisor host will periodically get software updates which + introduce a new firmware binary version. + +* Check the kernel, initrd and cmdline match the one used to boot + + If the guest is configured to use direct kernel boot, check that + the kernel, initrd and cmdline passed to this program match the + ones used to boot the guest. In the kernel cmdline whitespace + must be preserved exactly, including any leading or trailing + spaces. + +* Check whether the kernel hash measurement is enabled + + The ``kernelHashes`` property in the libvirt guest XML controls + whether hashes of the kernel, initrd and cmdline content are + covered by the boot measurement. If enabled, then the matching + content must be passed to this program. UIf disabled, then + the content must **NOT** be passed. + +* Check that the correct measurement hash is passed + + The measurement hash includes a nonce, so it will be different + on every boot attempt. Thus when validating the measuremnt it + is important ensure the most recent measurement is used. + +* Check the correct VMSA blobs / CPU SKU values for the host are used + + The VMSA blobs provide the initial register state for the + boot CPU and any additional CPUs. One of the registers + encodes the CPU SKU (family, model, stepping) of the physical + host CPU. Make sure that the VMSA blob used for validation + is one that matches the SKU of the host the guest is booted + on. Passing the CPU SKU values directly to the tool can + reduce the likelihood of using the wrong ones. + +* Check the CPU count is correct + + When passing VMSA blobs for SEV-ES guests, the number of CPUs + present will influence the measurement result. Ensure that the + correct vCPU count is used corresponding to the guest boot + attempt. + + +Best practice is to run this tool in completely offline mode and pass +all information as explicit command line parameters. When debugging +failures, however, it can be useful to tell it to connect to libvirt +and fetch information. If connecting to a remote libvirt instance, +it will fetch any information that can be trusted, which is the basic +VM launch state data. It will also sanity check the XML configuration +to identify some common mistakes. If the ``--insecure`` flag is passed +it can extract some configuration information and use that for the +attestation process. + +If the mistake still can't be identified, then this tool can be run +on the virtualization host. In that scenario the only three command +line parameters required are for the TIK, TEK and libvirt domain +name. It should be able to automatically determine all the other +information required. If it still reports a failure, this points +very strongly to the TIK/TEK pair not maching the configured +DH certificate and session blob. + +The ``--debug`` flag will display hashes and/or hex dumps for various +pieces of information used in the attestation process. Comparing the +``--debug`` output from running on the hypervisor host, against that +obtained when running in offline mode can give further guidance to +which parameter is inconsistent. + +As mentioned earlier in this document, bear in mind that in general +any attestation answers obtained from running on the hypervisor host +should not be trusted. So if a configuration mistake is identified +it is strongly recommended to re-run the attestation in offline mode +on a trusted machine. + + EXIT STATUS ===========