Require that all headers are guarded by a symbol named
LIBVIRT_$FILENAME
where $FILENAME is the uppercased filename, with all characters
outside a-z changed into '_'.
Note we do not use a leading __ because that is technically a
namespace reserved for the toolchain.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Record the index of each host-side veth device created and report
them to systemd, so they show up in machinectl status for the VM.
lxc-shell(95449419f969d649d9962566ec42af7d)
Since: Fri 2015-01-16 16:53:37 GMT; 3s ago
Leader: 28085 (sh)
Service: libvirt-lxc; class container
Iface: vnet0
Address: fe80::216:3eff:fe00:c317%124
OS: Fedora 21 (Twenty One)
Unit: machine-lxc\x2dshell.scope
└─28085 /bin/sh
Don't create the cgroups ahead of launching the container since
there is no need for the limits to apply during initial bootstrap.
Create the cgroup after the container PID is known and tell
systemd the initpid is the leader, instead of the controller
pid.
Since it is an abbreviation, USB should always be fully
capitalized or full lower case, never Usb.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Use the new virCgroupNewDetect function to determine cgroup
placement of existing running VMs. This will allow the legacy
cgroups creation APIs to be removed entirely
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Historically QEMU/LXC guests have been placed in a cgroup layout
that is
$LOCATION-OF-LIBVIRTD/libvirt/{qemu,lxc}/$VMNAME
This is bad for a number of reasons
- The cgroup hierarchy gets very deep which seriously
impacts kernel performance due to cgroups scalability
limitations.
- It is hard to setup cgroup policies which apply across
services and virtual machines, since all VMs are underneath
the libvirtd service.
To address this the default cgroup location is changed to
be
/system/$VMNAME.{lxc,qemu}.libvirt
This puts virtual machines at the same level in the hierarchy
as system services, allowing consistent policy to be setup
across all of them.
This also honours the new resource partition location from the
XML configuration, for example
<resource>
<partition>/virtualmachines/production</partitions>
</resource>
will result in the VM being placed at
/virtualmachines/production/$VMNAME.{lxc,qemu}.libvirt
NB, with the exception of the default, /system, path which
is intended to always exist, libvirt will not attempt to
auto-create the partitions in the XML. It is the responsibility
of the admin/app to configure the partitions. Later libvirt
APIs will provide a way todo this.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Instead of calling virCgroupForDomain every time we need
the virCgrouPtr instance, just do it once at Vm startup
and cache a reference to the object in virLXCDomainObjPrivatePtr
until shutdown of the VM. Removing the virCgroupPtr from
the LXC driver state also means we don't have stale mount
info, if someone mounts the cgroups filesystem after libvirtd
has been started
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the LXC controller creates the cgroup, configures the
resources and adds the task all in one go. This is not sufficiently
flexible for the forthcoming NBD integration. We need to make sure
the NBD process gets into the right cgroup immediately, but we can
not have limits (in particular the device ACL) applied at the point
where we start qemu-nbd. So create a virLXCCgroupCreate method
which creates the cgroup and adds the current task to be called
early, and leave virLXCCgroupSetup to only do resource config.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This adds support for host device passthrough with the
LXC driver. Since there is only a single kernel image,
it doesn't make sense to pass through PCI devices, but
USB devices are fine. For the latter we merely need to
make the /dev/bus/usb/NNN/MMM character device exist
in the container's /dev
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
with this patch,container's meminfo will be shown based on
containers' mem cgroup.
Right now,it's impossible to virtualize all values in meminfo,
I collect some values such as MemTotal,MemFree,Cached,Active,
Inactive,Active(anon),Inactive(anon),Active(file),Inactive(anon),
Active(file),Inactive(file),Unevictable,SwapTotal,SwapFree.
if I miss something, please let me know.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
https://www.gnu.org/licenses/gpl-howto.html recommends that
the 'If not, see <url>.' phrase be a separate sentence.
* tests/securityselinuxhelper.c: Remove doubled line.
* tests/securityselinuxtest.c: Likewise.
* globally: s/; If/. If/
Per the FSF address could be changed from time to time, and GNU
recommends the following now: (http://www.gnu.org/licenses/gpl-howto.html)
You should have received a copy of the GNU General Public License
along with Foobar. If not, see <http://www.gnu.org/licenses/>.
This patch removes the explicit FSF address, and uses above instead
(of course, with inserting 'Lesser' before 'General').
Except a bunch of files for security driver, all others are changed
automatically, the copyright for securify files are not complete,
that's why to do it manually:
src/security/security_selinux.h
src/security/security_driver.h
src/security/security_selinux.c
src/security/security_apparmor.h
src/security/security_apparmor.c
src/security/security_driver.c
Move the cgroup setup code out of the lxc_controller.c file
and into lxc_cgroup.{c,h}. This reduces the size of the
lxc_controller.c file and paves the way to invoke cgroup
setup from lxc_driver.c instead of lxc_controller.c in the
future
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
