The 'nodeset' variable was never initialized, causing a later
VIR_FREE(nodeset) to free uninitialized memory.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Intend to reduce the redundant code,use virNumaSetupMemoryPolicy
to replace virLXCControllerSetupNUMAPolicy and
qemuProcessInitNumaMemoryPolicy.
This patch also moves the numa related codes to the
file virnuma.c and virnuma.h
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Allow lxc using the advisory nodeset from querying numad,
this means if user doesn't specify the numa nodes that
the lxc domain should assign to, libvirt will automatically
bind the lxc domain to the advisory nodeset which queried from
numad.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
The LXC controller is closing loop devices as soon as the
container has started. This is fine if the loop device
was setup as a mounted filesystem, but if we're just passing
through the loop device as a disk, nothing else is keeping
it open. Thus we must keep the loop device FDs open for as
long the libvirt_lxc process is running.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the LXC controller creates the cgroup, configures the
resources and adds the task all in one go. This is not sufficiently
flexible for the forthcoming NBD integration. We need to make sure
the NBD process gets into the right cgroup immediately, but we can
not have limits (in particular the device ACL) applied at the point
where we start qemu-nbd. So create a virLXCCgroupCreate method
which creates the cgroup and adds the current task to be called
early, and leave virLXCCgroupSetup to only do resource config.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The naming used in the RPC protocols for the LXC monitor and
lock daemon confused the script used to generate systemtap
helper functions. Rename the LXC monitor protocol symbols to
reduce confusion. Adapt the gensystemtap.pl script to cope
with the LXC monitor / lock daemon naming conversions.
This has no functional impact on RPC wire protocol, since
names are only used in the C layer
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The virCaps structure gathered a ton of irrelevant data over time that.
The original reason is that it was propagated to the XML parser
functions.
This patch aims to create a new data structure virDomainXMLConf that
will contain immutable data that are used by the XML parser. This will
allow two things we need:
1) Get rid of the stuff from virCaps
2) Allow us to add callbacks to check and add driver specific stuff
after domain XML is parsed.
This first attempt removes pointers to private data allocation functions
to this new structure and update all callers and function that require
them.
When setting up disks with loop devices for LXC, one of the
switch cases was missing a 'break' causing it to fallthrough
to an error condition.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
By using a loopback device, disks backed by plain files can
be made available to LXC containers. We make no attempt to
auto-detect format if <driver type="raw"/> is not set,
instead we unconditionally treat that as meaning raw. This
is to avoid the security issues inherent with format
auto-detection
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently we rely on a VIR_ERROR message being logged by the
virRaiseError function to report LXC startup errors. This gives
the right message, but is rather ugly and can be truncated
if lots of log messages are written. Change the LXC controller
to explicitly print any virErrorPtr message to stderr. Then
change the driver to skip over anything that looks like a log
message.
The result is that this
error: Failed to start domain busy
error: internal error guest failed to start: 2013-03-04 19:46:42.846+0000: 1734: info : libvirt version: 1.0.2
2013-03-04 19:46:42.846+0000: 1734: error : virFileLoopDeviceAssociate:600 : Unable to open /root/disk.raw: No such file or directory
changes to
error: Failed to start domain busy
error: internal error guest failed to start: Unable to open /root/disk.raw: No such file or directory
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
To enable locking to be introduced to the security manager
objects later, turn virSecurityManager into a virObjectLockable
class
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
To enable virCapabilities instances to be reference counted,
turn it into a virObject. All cases of virCapabilitiesFree
turn into virObjectUnref
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
To avoid confusion between the LXC driver <-> controller
monitor RPC protocol and the libvirt-lxc.so <-> libvirtd public
RPC protocol, rename the former to lxc_monitor_protocol.x
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The code for setting up a private /dev/pts for the containers
is also responsible for making the LXC controller have a
private mount namespace. Unfortunately the /dev/pts code is
not run if launching a container without a custom root. This
causes the LXC FUSE mount to leak into the host FS.
Convert the host capabilities and domain config structs to
use the virArch datatype. Update the parsers and all drivers
to take account of datatype change
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
this patch addes fuse support for libvirt lxc.
we can use fuse filesystem to generate sysinfo dynamically,
So we can isolate /proc/meminfo,cpuinfo and so on through
fuse filesystem.
we mount fuse filesystem for every container.
the mount name is libvirt,mount point is
localstatedir/run/libvirt/lxc/containername.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
When no security driver is specified libvirt_lxc segfaults as a debug
message tries to access security labels for the container that are not
present.
This problem was introduced in commit 6c3cf57d6c.
Early jumps to the cleanup label caused a crash of the libvirt_lxc
container helper as the cleanup section called
virLXCControllerDeleteInterfaces(ctrl) without checking the ctrl argument
for NULL. The argument was de-referenced soon after.
$ /usr/libexec/libvirt_lxc
/usr/libexec/libvirt_lxc: missing --name argument for configuration
Segmentation fault
The virLXCControllerClientCloseHook method was mistakenly
assuming that the private data associated with the network
client was the virLXCControllerPtr. In fact it was just a
dummy int, so we were derefencing a bogus struct. The
frequent result of this was that we would never quit, because
we tried to arm a non-existant timer.
Fix the code by removing the dummy private data and just
using the virLXCControllerPtr instance as private data
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Currently the LXC driver logs audit messages when a container
is started or stopped. These audit messages, however, contain
the PID of the libvirt_lxc supervisor process. To enable
sysadmins to correlate with audit messages generated by
processes /inside/ the container, we need to include the
container init process PID.
We can't do this in the main 'start' audit message, since
the init PID is not available at that point. Instead we output
a completely new audit record, that lists both PIDs.
type=VIRT_CONTROL msg=audit(1353433750.071:363): pid=20180 uid=0 auid=501 ses=3 subj=unconfined_u:unconfined_r:unconfined_t:s0-s0:c0.c1023 msg='virt=lxc op=init vm="busy" uuid=dda7b947-0846-1759-2873-0f375df7d7eb vm-pid=20371 init-pid=20372 exe="/home/berrange/src/virt/libvirt/daemon/.libs/lt-libvirtd" hostname=? addr=? terminal=pts/6 res=success'
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The LXC controller code currently directly invokes the
libvirt main loop code. The problem is that this misses
the cleanup of virNetServerClient connections that
virNetServerRun takes care of.
The result is that when libvirtd is stopped, the
libvirt_lxc controller process gets stuck in a I/O loop.
When libvirtd is then started again, it fails to connect
to the controller and thus kills off the entire domain.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Add two new APIs virNetServerClientNewPostExecRestart and
virNetServerClientPreExecRestart which allow a virNetServerClientPtr
object to be created from a JSON object and saved to a
JSON object, for the purpose of re-exec'ing a process.
This includes serialization of the connected socket associated
with the client
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Many parts of virDomainDefPtr were using 'int' variables as
array length counts. Replace all these with size_t and update
various format strings & API signatures to adapt
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Continue consolidation of process functions by moving some
helpers out of command.{c,h} into virprocess.{c,h}
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
https://www.gnu.org/licenses/gpl-howto.html recommends that
the 'If not, see <url>.' phrase be a separate sentence.
* tests/securityselinuxhelper.c: Remove doubled line.
* tests/securityselinuxtest.c: Likewise.
* globally: s/; If/. If/
This patch updates the structures that store information about each
domain and each hypervisor to support multiple security labels and
drivers. It also updates all the remaining code to use the new fields.
Signed-off-by: Marcelo Cerri <mhcerri@linux.vnet.ibm.com>
Currently there is a hook function that is invoked when a
new client connection comes in, which allows an app to
setup private data. This setup will make it difficult to
serialize client state during process re-exec(). Change to
a model where the app registers a callback when creating
the virNetServerPtr instance, which is used to allocate
the client private data immediately during virNetClientPtr
construction.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
All callers used the same initialization seed (well, the new
viratomictest forgot to look at getpid()); so we might as well
make this value automatic. And while it may feel like we are
giving up functionality, I documented how to get it back in the
unlikely case that you actually need to debug with a fixed
pseudo-random sequence. I left that crippled by default, so
that a stray environment variable doesn't cause a lack of
randomness to become a security issue.
* src/util/virrandom.c (virRandomInitialize): Rename...
(virRandomOnceInit): ...and make static, with one-shot call.
Document how to do fixed-seed debugging.
* src/util/virrandom.h (virRandomInitialize): Drop prototype.
* src/libvirt_private.syms (virrandom.h): Don't export it.
* src/libvirt.c (virInitialize): Adjust caller.
* src/lxc/lxc_controller.c (main): Likewise.
* src/security/virt-aa-helper.c (main): Likewise.
* src/util/iohelper.c (main): Likewise.
* tests/seclabeltest.c (main): Likewise.
* tests/testutils.c (virtTestMain): Likewise.
* tests/viratomictest.c (mymain): Likewise.
The reboot() syscall is allowed by new kernels for LXC containers.
The LXC controller can detect whether a reboot was requested
(instead of a normal shutdown) by looking at the "init" process
exit status. If a reboot was triggered, the exit status will
record SIGHUP as the kill reason.
The LXC controller has cleared all its capabilities, and the
veth network devices will no longer exist at this time. Thus
it cannot restart the container init process itself. Instead
it emits an event which is picked up by the LXC driver in
libvirtd. This will then re-create the container, using the
same configuration as it was previously running with (ie it
will not activate 'newDef').
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This defines a new RPC protocol to be used between the LXC
controller and the libvirtd LXC driver. There is only a
single RPC message defined thus far, an asynchronous "EXIT"
event that is emitted just before the LXC controller process
exits. This provides the LXC driver with details about how
the container shutdown - normally, or abnormally (crashed),
thus allowing the driver to emit better libvirt events.
Emitting the event in the LXC controller requires a few
little tricks with the RPC service. Simply calling the
virNetServiceClientSendMessage does not work, since this
merely queues the message for asynchronous processing.
In addition the main event loop is no longer running at
the point the event is emitted, so no I/O is processed.
Thus after invoking virNetServiceClientSendMessage it is
necessary to mark the client as being in "delayed close"
mode. Then the event loop is run again, until the client
completes its close - this happens only after the queued
message has been fully transmitted. The final complexity
is that it is not safe to run virNetServerQuit() from the
client close callback, since that is invoked from a
context where the server is locked. Thus a zero-second
timer is used to trigger shutdown of the event loop,
causing the controller to finally exit.
* src/Makefile.am: Add rules for generating RPC protocol
files and dispatch methods
* src/lxc/lxc_controller.c: Emit an RPC event immediately
before exiting
* src/lxc/lxc_domain.h: Record the shutdown reason
given by the controller
* src/lxc/lxc_monitor.c, src/lxc/lxc_monitor.h: Register
RPC program and event handler. Add callback to let
driver receive EXIT event.
* src/lxc/lxc_process.c: Use monitor exit event to decide
what kind of domain event to emit
* src/lxc/lxc_protocol.x: Define wire protocol for LXC
controller monitor.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>