The network XML is updated in the following ways:
1) The <forward> element can now contain a list of forward interfaces:
<forward .... >
<interface dev='eth10'/>
<interface dev='eth11'/>
<interface dev='eth12'/>
<interface dev='eth13'/>
</forward>
The first of these takes the place of the dev attribute that is
normally in <forward> - when defining a network you can specify
either one, and on output both will be present. If you specify
both on input, they must match.
2) In addition to forward modes of 'nat' and 'route', these new modes
are supported:
private, passthrough, vepa - when this network is referenced by a
domain's interface, it will have the same effect as if the
interface had been defined as type='direct', e.g.:
<interface type='direct'>
<source mode='${mode}' dev='${dev}>
...
</interface>
where ${mode} is one of the three new modes, and ${dev} is an interface
selected from the list given in <forward>.
bridge - if a <forward> dev (or multiple devs) is defined, and
forward mode is 'bridge' this is just like the modes 'private',
'passthrough', and 'vepa' above. If there is no forward dev
specified but a bridge name is given (e.g. "<bridge
name='br0'/>"), then guest interfaces using this network will use
libvirt's "host bridge" mode, equivalent to this:
<interface type='bridge'>
<source bridge='${bridge-name}'/>
...
</interface>
3) A network can have multiple <portgroup> elements, which may be
selected by the guest interface definition (by adding
"portgroup='${name}'" in the <source> element along with the
network name). Currently a portgroup can only contain a
virtportprofile, but the intent is that other configuration items
may be put there int the future (e.g. bandwidth config). When
building a guest's interface, if the <interface> XML itself has no
virtportprofile, and if the requested network has a portgroup with
a name matching the name given in the <interface> (or if one of the
network's portgroups is marked with the "default='yes'" attribute),
the virtportprofile from that portgroup will be used by the
interface.
4) A network can have a virtportprofile defined at the top level,
which will be used by a guest interface when connecting in one of
the 'direct' modes if the guest interface XML itself hasn't
specified any virtportprofile, and if there are also no matching
portgroups on the network.
This commit introduces names definition for the DNS hosts file using
the following syntax:
<dns>
<host ip="192.168.1.1">
<name>alias1</name>
<name>alias2</name>
</host>
</dns>
Some of the improvements and fixes were done by Laine Stump so
I'm putting him into the SOB clause again ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
This commit introduces the <dns> element and <txt> record for the
virtual DNS network. The DNS TXT record can be defined using following
syntax in the network XML file:
<dns>
<txt name="example" value="example value" />
</dns>
Also, the Relax-NG scheme has been altered to allow the texts without
spaces only for the name element and some nitpicks about memory
free'ing have been fixed by Laine so therefore I'm adding Laine to the
SOB clause ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
Make virtTestLoadFile allocate the buffer to read the file into.
Fix logic error in virtTestLoadFile, stop reading on the first empty line.
Use virFileReadLimFD in virtTestCaptureProgramOutput to avoid manual
buffer handling.
A few of the tests were missing basic sanity checks, while most
of them were doing copy-and-paste initialization (in fact, some
of them pasted the argc > 1 check more than once!). It's much
nicer to do things in one common place, and minimizes the size of
the next patch that fixes getcwd usage.
* tests/testutils.h (EXIT_AM_HARDFAIL): New define.
(progname, abs_srcdir): Define for all tests.
(VIRT_TEST_MAIN): Change callback signature.
* tests/testutils.c (virtTestMain): Do more common init.
* tests/commandtest.c (mymain): Simplify.
* tests/cputest.c (mymain): Likewise.
* tests/esxutilstest.c (mymain): Likewise.
* tests/eventtest.c (mymain): Likewise.
* tests/hashtest.c (mymain): Likewise.
* tests/networkxml2xmltest.c (mymain): Likewise.
* tests/nodedevxml2xmltest.c (myname): Likewise.
* tests/nodeinfotest.c (mymain): Likewise.
* tests/nwfilterxml2xmltest.c (mymain): Likewise.
* tests/qemuargv2xmltest.c (mymain): Likewise.
* tests/qemuhelptest.c (mymain): Likewise.
* tests/qemuxml2argvtest.c (mymain): Likewise.
* tests/qemuxml2xmltest.c (mymain): Likewise.
* tests/qparamtest.c (mymain): Likewise.
* tests/sexpr2xmltest.c (mymain): Likewise.
* tests/sockettest.c (mymain): Likewise.
* tests/statstest.c (mymain): Likewise.
* tests/storagepoolxml2xmltest.c (mymain): Likewise.
* tests/storagevolxml2xmltest.c (mymain): Likewise.
* tests/virbuftest.c (mymain): Likewise.
* tests/virshtest.c (mymain): Likewise.
* tests/vmx2xmltest.c (mymain): Likewise.
* tests/xencapstest.c (mymain): Likewise.
* tests/xmconfigtest.c (mymain): Likewise.
* tests/xml2sexprtest.c (mymain): Likewise.
* tests/xml2vmxtest.c (mymain): Likewise.
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in network_conf.{h,c} and update all callers to
match
This patch adds an optional attribute to the <bootp> tag, that
allows to specify a TFTP server address other than the address of
the DHCP server itself.
This can be used to forward the BOOTP settings of the host down to the
guest. This is something that configurations such as Xen's default
network achieve naturally, but must be done manually for NAT.
* docs/formatnetwork.html.in: Document new attribute.
* docs/schemas/network.rng: Add it to schema.
* src/conf/network_conf.h: Add it to struct.
* src/conf/network_conf.c: Add it to parser and pretty printer.
* src/network/bridge_driver.c: Put it in the dnsmasq command line.
* tests/networkxml2xmlin/netboot-proxy-network.xml
tests/networkxml2xmlout/netboot-proxy-network.xml
tests/networkxml2xmltest.c: add new tests
