As my punishment for the break in 7f15ebc7 (fixed in 752596b5dd) I'm
introducing this test to make sure it won't happen again. Currently,
only test for <graphics/> is supported.
This patch adds functionality to allow libvirt to configure the
'native-tagged' and 'native-untagged' modes on openvswitch networks.
Signed-off-by: Laine Stump <laine@redhat.com>
Add <features> and <compat> elements to volume target XML.
<compat> is a string which for qcow2 represents the QEMU version
it should be compatible with. Valid values are 0.10 and 1.1.
1.1 is implicit if the <features> element is present, otherwise
qemu-img default is used. 0.10 can be specified to explicitly
create older images after the qemu-img default changes.
<features> contains optional features, so far
<lazy_refcounts/> is available, which enables caching of reference
counters, improving performance for snapshots.
Currently, a listen address for a SPICE server can be specified. Later,
when the domain is migrated, we need to relocate the graphics which
involves telling new destination to the SPICE server. However, we can't
just assume the listen address is the new location, because the listen
address can be ANYCAST (0.0.0.0 for IPv4, :: for IPv6). In which case,
we want to pass the remote hostname. But there are some troubles with
ANYCAST. In both IPv4 and IPv6 it has many ways for specifying such
address. For instance, in IPv4: 0, 0.0, 0.0.0, 0.0.0.0. The number of
variations gets bigger in IPv6 world. Hence, in order to check for
ANYCAST address sanely, we should take the provided listen address,
parse it and format back in it's full form. Which is exactly what this
patch does.
If the creation of the commandline failed, libvirt always reported "out
of memory" from the virCommandToString function rather than the proper
error that happened in virStorageBackendCreateQemuImgCmd. Error out
earlier.
With unknown good reasons, the attribute "bus" of scsi device
address is always set to 0, same for attribute "target". (See
virDomainDiskDefAssignAddress).
Though we might need to change the algorithm to honor "bus"
and "target" too, that's a different issue. The address generator
for scsi host device in this patch just follows the unknown
good reasons, only considering the "controller" and "unit".
It walks through all scsi controllers and their units, to see
if the address $controller:0:0:$unit can be used (if not used
by any disk or scsi host device yet), if found one, it sits on
it, otherwise, it creates a new controller (actually the controller
is implicitly created by someone else), and sits on
$new_controller:0:0:0 instead.
A mingw build (where the qemu driver is not built, so WITH_QEMU
is undefined) failed with:
In file included from ../../src/qemu/qemu_command.h:30:0,
from ../../tests/testutilsqemu.h:4,
from ../../tests/networkxml2xmltest.c:14:
../../src/qemu/qemu_conf.h:53:4: error: #error "Port me"
But since testutilsqemu.c is already conditional, the header
should be likewise.
* tests/testutilsqemu.h: Make content conditional.
Signed-off-by: Eric Blake <eblake@redhat.com>
We can't use GNULIB's fprintf-posix due to licensing
incompatibilities. We do already have a portable
formatting via virAsprintf() which we got from GNULIB
though. We can use to create a virFilePrintf() function.
But really gnulib could just provide a 'fprintf'
module, that depended on just its 'asprintf' module.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
It may shorten the code a bit as the following pattern:
VIR_STRNDUP(dst, src, cond ? n : strlen(src))
is used on several places among our code. However, we can
move the strlen into virStrndup and thus write just:
VIR_STRNDUP(dst, src, cond ? n : -1)
Currently, the controllers argument to virCgroupDetect acts both as
a result filter and a required controller specification, which is
a bit overloaded. If both functionalities are needed, it would be
better to have them seperated into a filter and a requirement mask.
The only situation where it is used today is to ensure that only
CPU related controllers are used for the VCPU directories. But here
we clearly do not want to enforce the existence of cpu, cpuacct and
specifically not cpuset at the same time.
This commit changes the semantics of controllers to "filter only".
Should a required mask ever be needed, more work will have to be done.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
This attribute is going to represent number of queues for
multique vhost network interface. This commit implements XML
extension part of the feature and add one test as well. For now,
we can only do xml2xml test as qemu command line generation code
is not adapted yet.
The shunloadStart function didn't check the status of virInitialize which
was flagged by Coverity. Adjust the function and shunloadtest in order
to handle the situation.
Since 0d70656afd, it starts to access the sysfs files to build
the qemu command line (by virSCSIDeviceGetSgName, which is to find
out the scsi generic device name by adpater🚌target:unit), there
is no way to work around, qemu wants to see the scsi generic device
like "/dev/sg6" anyway.
And there might be other places which need to access sysfs files
when building qemu command line in future.
Instead of increasing the arguments of qemuBuildCommandLine, this
introduces a new callback for qemuBuildCommandLine, and thus tests
can register their own callbacks for sysfs test input files accessing.
* src/qemu/qemu_command.h: (New callback struct
qemuBuildCommandLineCallbacks;
extern buildCommandLineCallbacks)
* src/qemu/qemu_command.c: (wire up the callback struct)
* src/qemu/qemu_driver.c: (Use the new syntax of qemuBuildCommandLine)
* src/qemu/qemu_hotplug.c: Likewise
* src/qemu/qemu_process.c: Likewise
* tests/testutilsqemu.[ch]: (Helper testSCSIDeviceGetSgName;
callback struct testCallbacks;)
* tests/qemuxml2argvtest.c: (Use testCallbacks)
* src/tests/qemuxmlnstest.c: (Like above)
Running make check in a VPATH configured build directory fails
in fchosttest as the test data files are searched for relative to
the current working directory.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
QEMU might support more values for "-drive discard", so using Bi-state
values (on/off) for it doesn't make sense.
"on" maps to "unmap", "off" maps to "ignore":
<...>
@var{discard} is one of "ignore" (or "off") or "unmap" (or "on") and
controls whether @dfn{discard} (also known as @dfn{trim} or @dfn{unmap})
requests are ignored or passed to the filesystem. Some machine types
may not support discard requests.
</...>
The reason for it's not exposed for such long time is that the
enums for VirtioEventIdx and CopyOnReadType have same enum values
and Correspondingstrings. This fixes the bug and adds test.
The surest way to avoid regressions is to test documented behavior :)
* tests/virstringtest.c (testStrdup): New test case.
Signed-off-by: Eric Blake <eblake@redhat.com>
If the <sysinfo> system table 'uuid' field is improperly formatted,
then qemu will fail to start the guest with the error:
virsh start dom
error: Failed to start domain dom
error: internal error process exited while connecting to monitor: Invalid SMBIOS UUID string
This was because the parsing rules were lax with respect to allowing extraneous
spaces and dashes in the provided UUID. As long as there were 32 hexavalues
that matched the UUID for the domain the string was accepted. However startup
failed because the string format wasn't correct. This patch will adjust the
string format so that when it's presented to the driver it's in the expected
format.
Added a test for uuid comparison within sysinfo.
QEMU introduced "discard" option for drive since commit a9384aff53,
<...>
@var{discard} is one of "ignore" (or "off") or "unmap" (or "on") and
controls whether @dfn{discard} (also known as @dfn{trim} or @dfn{unmap})
requests are ignored or passed to the filesystem. Some machine types
may not support discard requests.
</...>
This patch exposes the support in libvirt.
QEMU supported "discard" for "-drive" since v1.5.0-rc0:
% git tag --contains a9384aff53
contains
v1.5.0-rc0
v1.5.0-rc1
So this only detects the capability bit using virQEMUCapsProbeQMPCommandLine.
Adding a VNC WebSocket support for QEMU driver. This functionality is
in upstream qemu from commit described as v1.3.0-982-g7536ee4, so the
capability is being recognized based on QEMU version for now.
QEMU introduced command line "-mem-merge=on|off" (defaults to on) to
enable/disable the memory merge (KSM) at guest startup. This exposes
it by new XML:
<memoryBacking>
<nosharepages/>
</memoryBacking>
The XML tag is same with what we used internally for old RHEL.
Files ending in -invalid.xml are expected to violate the
XML schema check. The RBD file does not so must have a
different filename.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The QEMU command line syntax for RBD disks is
file=rbd:pool/image:opt1=val1:opt2=val2...
There is no way to escape the ':' if it appears in the
pool or image name. Thus it must be explicitly forbidden
if it occurs in the libvirt XML. People are known to
be abusing the lack of escaping in current libvirt to
pass arbitrary args to QEMU.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Clang does not like it when you pass a static variable to an
inline function
vircgroupmock.c:462:22: error: static variable 'fakesysfsdir' is
used in an inline function with external linkage [-Werror,-Wstatic-in-inline]
Just make the var non-static to avoid this
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Ever since the conversion to using only QMP for probing features
of qemu 1.2 and newer, we have been unable to detect features
that are added only by additional command line options. For
example, we'd like to know if '-machine mem-merge=on' (added
in qemu 1.5) is present. To do this, we will take advantage
of qemu 1.5's query-command-line-parameters QMP call [1].
This patch wires up the framework for probing the command results;
if the QMP command is missing, or if a particular command line
option does not output any parameters (for example, -net uses
a polymorphic parser, which showed up as no parameters as of qemu
1.5), we silently treat that command as having no results.
[1] https://lists.gnu.org/archive/html/qemu-devel/2013-04/msg05180.html
* src/qemu/qemu_monitor.h (qemuMonitorGetOptions)
(qemuMonitorSetOptions)
(qemuMonitorGetCommandLineOptionParameters): New functions.
* src/qemu/qemu_monitor_json.h
(qemuMonitorJSONGetCommandLineOptionParameters): Likewise.
* src/qemu/qemu_monitor.c (_qemuMonitor): Add cache field.
(qemuMonitorDispose): Clean it.
(qemuMonitorGetCommandLineOptionParameters): Implement new function.
* src/qemu/qemu_monitor_json.c
(qemuMonitorJSONGetCommandLineOptionParameters): Likewise.
(testQemuMonitorJSONGetCommandLineParameters): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
In an upcoming patch, I need the way to safely transfer a nested
virJSON object out of its parent container for independent use,
even after the parent is freed.
* src/util/virjson.h (virJSONValueObjectRemoveKey): New function.
(_virJSONObject, _virJSONArray): Use correct type.
* src/util/virjson.c (virJSONValueObjectRemoveKey): Implement it.
* src/libvirt_private.syms (virjson.h): Export it.
* tests/jsontest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
network: static route support for <network>
This patch adds the <route> subelement of <network> to define a static
route. the address and prefix (or netmask) attribute identify the
destination network, and the gateway attribute specifies the next hop
address (which must be directly reachable from the containing
<network>) which is to receive the packets destined for
"address/(prefix|netmask)".
These attributes are translated into an "ip route add" command that is
executed when the network is started. The command used is of the
following form:
ip route add <address>/<prefix> via <gateway> \
dev <virbr-bridge> proto static metric <metric>
Tests are done to validate that the input data are correct. For
example, for a static route ip definition, the address must be a
network address and not a host address. Additional checks are added
to ensure that the specified gateway is directly reachable via this
network (i.e. that the gateway IP address is in the same subnet as one
of the IP's defined for the network).
prefix='0' is supported for both family='ipv4' address='0.0.0.0'
netmask='0.0.0.0' or prefix='0', and for family='ipv6' address='::',
prefix=0', although care should be taken to not override a desired
system default route.
Anytime an attempt is made to define a static route which *exactly*
duplicates an existing static route (for example, address=::,
prefix=0, metric=1), the following error message will be sent to
syslog:
RTNETLINK answers: File exists
This can be overridden by decreasing the metric value for the route
that should be preferred, or increasing the metric for the route that
shouldn't be preferred (and is thus in place only in anticipation that
the preferred route may be removed in the future). Caution should be
used when manipulating route metrics, especially for a default route.
Note: The use of the command-line interface should be replaced by
direct use of libnl so that error conditions can be handled better. But,
that is being left as an exercise for another day.
Signed-off-by: Gene Czarcinski <gene@czarc.net>
Signed-off-by: Laine Stump <laine@laine.org>
