VM drivers may need to store additional private data to the status XML
so that it can be restored after libvirtd restart. Since not everything
is needed add a callback infrastructure, where VM drivers can add only
stuff they need.
Note that the private data is formatted as a <privateData> sub-element
of the <disk> or <backingStore> <source> sub-element. This is done since
storing it out of band (in the VM private data) would require a complex
matching process to allow to put the data into correct place.
Commit id '70249927b' neglected to cover this case because the test
had taken the "shortcut" to already add the <address>; however, when
the PCI address assignment code was adjusted by commit id '70249927'
the vhost-scsi (VIR_DOMAIN_HOSTDEV_SUBSYS_TYPE_SCSI_HOST) wasn't
covered thus returning a 0 for pciFlags. So I altered the tests too
to make sure it doesn't happen again.
Previously the qemuxml2xmloutdata was a softlink to the source
qemuxml2argvdata, so I unlinked and recreated the output file to
force generation of the adddress. Without the test changes, an
address generation returns:
libvirt: Domain Config error : internal error: Cannot automatically
add a new PCI bus for a device with connect flags 00
if an address was supplied in the test, a restart of libvirtd or
edit of a guest would display the following opaque message:
warning : qemuDomainCollectPCIAddress:1237 :
qemuDomainDeviceCalculatePCIConnectFlags() thinks that the device
with PCI address 0000:00:09.0 should not have a PCI address
where the address is related to the guest PCI address provided.
Commit id 'c5c96545' neglected to validate that the srcPriv was
non-NULL before dereferencing. Similar problem to what was fixed
by commit id '8056721c' but missed during multiple rebases and
code reworks.
ncpus would be -1 on error and the cleanup for loop would not be skipped
in this case.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1522706
If domain is active, but the undefine API was called without the
VIR_DOMAIN_UNDEFINE_KEEP_NVRAM flag set, the following incorrect
error message is produced:
error: Requested operation is not valid: cannot delete inactive domain with nvram
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Move the IDE controller check from command line building to
controller def validation. Also explicitly include the avoidance
check for the implicit IDE controller from qemuBuildSkipController.
Cause the IDE case for command line building to generate a
failure if called to add an IDE since that shouldn't happen
if the Validate code did the right thing.
Move the call to qemuDomainCheckCCWS390AddressSupport from
qemuBuildControllerDevStr to qemuDomainDeviceDefValidateController.
This means we will get the qemuCaps from the driver opaque
variable passed to qemuDomainDeviceDefValidate.
When reconnecting to a running domain started by old libvirt, which did
not change host-model into a custom CPU definition, we replace the CPU
definition with a specific CPU model from host capabilities. However,
that CPU model may not be supported by the running qemu process. We need
to translate the CPU model to one of the models which libvirt could have
used when starting the domain.
https://bugzilla.redhat.com/show_bug.cgi?id=1521202
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
virQEMUCapsProbeQMPCPUDefinitions is now a small wrapper which fills in
qemuCaps with CPU models fetched by virQEMUCapsFetchCPUDefinitions.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Since we are re-detecting the backing chain after pivoting to the active
block commit target (or block copy target) the disk index needs to be
reset to 0. This is necessary since we move a member of the backing
chain to disk->src but clear indexes only starting from
disk->src->backingStore. The freshly detected images have indexes
starting from 1, but since we've pivoted into an image which was
previously a backing store it would have a non-0 index.
The lookup function would then return the top of the chain for queries
like 'vda[1]' instead of the first backing store.
This problem will not be present once we keep the disk indexes stable.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1519745
Separate the logic of creating devices from their gathering.
Use this new function in qemuDomainNamespaceSetupHostdev and
qemuDomainNamespaceSetupDisk.
This patch pass event error up to the place where we can
use it. Error is passed only for sync blockjob event mode
as we can't use the error in async mode. In async mode we
just pass the event details to the client thru event API
but current blockjob event API can not carry extra parameter.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
==899== 39 bytes in 1 blocks are definitely lost in loss record 732 of 1,003
==899== at 0x4C2AEDF: malloc (vg_replace_malloc.c:299)
==899== by 0x8B68CE7: vasprintf (in /lib64/libc-2.25.so)
==899== by 0x55498D2: virVasprintfInternal (virstring.c:708)
==899== by 0x55499E7: virAsprintfInternal (virstring.c:729)
==899== by 0x2BECFFF0: qemuGetMemoryBackingBasePath (qemu_conf.c:1757)
==899== by 0x2BF23225: qemuStateInitialize (qemu_driver.c:893)
==899== by 0x563073D: virStateInitialize (libvirt.c:770)
==899== by 0x124CC4: daemonRunStateInit (libvirtd.c:834)
==899== by 0x55521CD: virThreadHelper (virthread.c:206)
==899== by 0x88D9686: start_thread (in /lib64/libpthread-2.25.so)
==899== by 0x8BEAEFE: clone (in /lib64/libc-2.25.so)
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Raw local files do not pass through the backing store detector and thus
the code did not allocate the required backing store terminator for
them. Previously the terminating element would be formatted into the XML
since the default values used for the metadata allowed that. This is a
regression since a693fdba01 which was not detected in the review.
This patch also reverts all the changes in the test files.
Until now we would skip loading of the backing chain for files which
don't support backing chains only when starting up the VM. Move the
check from qemuProcessPrepareHostStorage with some adaptations so that's
always applied.
In status XML, we do not store the QEMU version information, we only
format all the capabilities. We dropped QEMU_CAPS_PCI_MULTIBUS
in commit 5b783379 which was released in libvirt 3.2.0.
Therefore the only way of telling if the already running domain
at the time of daemon restart has been started with a QEMU that does
use 'pci.0' or not on PPC is to look at the pci-root controller's
alias. This is not an option if the domain has a user-specified alias
for the pci-root.
Instead of reintroducing the capability, assume 'pci.0' when we have
no version information. That way the only left broken use case would
be the combination of user aliases and very old QEMU.
Partially reverts commit 3a37af1e4.
https://bugzilla.redhat.com/show_bug.cgi?id=1518148
We do not fill out qemuCaps->arch when parsing status XML.
Use def->os.arch like we do for PPC.
This fixes hotplug after daemon restart for domains that use
a user alias for the implicit pci-root on x86.
https://bugzilla.redhat.com/show_bug.cgi?id=1518148
For some corner cases, virQEMUCapsHasPCIMultiBus depends on the QEMU
version, which is by design not stored in the status XML and therefore
it cannot be fixed for all existing running domains.
Prefer the controller alias read from the status XML when formatting
PCI addresses and only fall back to using virQEMUCapsHasPCIMultiBus
if the alias is a user alias.
This fixes hotplug after daemon restart for domains not using user
aliases.
Partially reverts commit 937f3195.
https://bugzilla.redhat.com/show_bug.cgi?id=1518148
Adjust function descriptions of virQEMUCapsInitCPUModelS390 and
virQEMUCapsInitCPUModel to the changes introduced with
commitID 74fc32a955.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Marc Hartmayer <mhartmay@linux.vnet.ibm.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Even though we never format the device on the QEMU command line,
as it's a platform serial device that's not user-instantiable,
we should still make sure it's available before using it.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
All serial devices shoule have an associated capability.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
We should make sure the isa-serial device is available before
formatting it on the QEMU command line.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
All serial devices shoule have an associated capability.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Now that <serial> and <console> on s390/s390x behave a bit more like the
other architectures, remove this extra differentation, and use sclp
console by default for new guests. New virtio consoles can still be
added, and it is actually needed because of the limited number of
instances for sclp and sclplm.
This reverts commit b1c88c1476, whose
reasons are not totally clear.
Signed-off-by: Pino Toscano <ptoscano@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Introduce specific a target types with two models for the console
devices (sclp and sclplm) used in s390 and s390x guests, so isa-serial
is no more used for them.
This makes <serial> usable on s390 and s390x guests, with at most only
a single sclpconsole and one sclplmconsole devices usable in a single
guest (due to limitations in QEMU, which will enforce already at
runtime).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1449265
Signed-off-by: Pino Toscano <ptoscano@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
We can finally introduce a specific target model for the pl011 device
used by mach-virt guests, which means isa-serial will no longer show
up to confuse users.
We make sure migration works in both directions by interpreting the
isa-serial target type, or the lack of target type, appropriately
when parsing the guest XML, and skipping the newly-introduced type
when formatting if for migration. We also verify that pl011 is not
used for non-mach-virt guests and add a bunch of test cases.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=151292
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
The existing implementation set the address type for all serial
devices to spapr-vio, which made it impossible to use other devices
such as usb-serial and pci-serial; moreover, some decisions were
made based on the address type rather than the device type.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1512934
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
We can finally introduce a specific target model for the spapr-vty
device used by pSeries guests, which means isa-serial will no longer
show up to confuse users.
We make sure migration works in both directions by interpreting the
isa-serial target type, or the lack of target type, appropriately
when parsing the guest XML, and skipping the newly-introduced type
when formatting if for migration. We also verify that spapr-vty is
not used for non-pSeries guests and add a bunch of test cases.
This commit is best viewed with 'git show -w'.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1511421
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Instead duplicating the capability check for each possible target
model, introduce a small helper that matches the target model with
the corresponding capability and collapse all existing checks into
a single one.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Now that we've created a distinction between target type and target
model, with the latter being the concrete device name, it's time to
switch to formatting the model instead of the type.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Target model and target type must agree for the configuration
to make sense, so check that's actually the case and error out
otherwise.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Instead of validating each target type / address type combination
separately, create a small helper to perform the matching and
collapse all existing checks into a single one.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Instead of waiting until we get to command line generation, we can
validate the target for a char device much earlier.
Move all the checks out of qemuBuildSerialChrDeviceStr() and into
the new fuction. This will later allow us to validate the target
for platform devices.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
This is the first step in getting rid of the assumption that
isa-serial is the default target type for serial devices.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Having a separate function for char device handling is better than
adding even more code to qemuDomainDeviceDefPostParse().
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Marc Hartmayer <mhartmay@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1425757
The blockdev-add code provides a mechanism to sanely provide user
and password-secret arguments for iscsi without placing them on the
command line to be viewable by a 'ps -ef' type command or needing
to create separate -iscsi devices for each disk/volume found.
So modify the iSCSI command line building to check for the presence
of the capability in order properly setup and use the domain master
secret object to encrypt the password in a secret object and alter
the parameters for the command line to utilize.
Modify the xml2argvtest to exhibit the syntax for both disk and
hostdev configurations.
Detect the capability via the query-qmp-schema for blockdev-add
to find the 'password-secret' parameter that will allow the iSCSI
code to use the master secret object to encrypt the secret for an
and only need to provide the object id of the secret on the command
line thus obsfuscating the passphrase.
Rather than picking apart the two pieces we need/want (path, hosts,
and auth)- let's allocate/use a virStorageSourcePtr for iSCSI storage.
The end result is that qemuBuildSCSIiSCSIHostdevDrvStr doesn't need
to "fake" one for the qemuBuildNetworkDriveStr call.
Libvirt prints an error on startup when it is missing host cpu model
information for any queried qemu binary. On s390 we only have host cpu model
information for kvm enabled qemu instances. So when virt type is not kvm, this
is actually not an error on s390.
This patch adds virt type as a parameter to virQEMUCapsInitCPUModelS390, and a
new return code 2 for virQEMUCapsInitCPUModel and virQEMUCapsInitCPUModelS390.
If the virt type is not kvm then we skip printing the scary error message
and return 2 because this case is actually expected behavior. The new return
code is meant to differentiate between the failure case and the case where we
simply expect the cpu model information to be unattainable.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Marc Hartmayer <mhartmay@linux.vnet.ibm.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Move the setup of the disk attribute to the disk source prepare function
which will allow proper usage with JSON props and move the fallback
(legacy) generating code into the block which is executed with legacy
options.
As a side-effect of this change we can clean up propagation of 'cfg'
into the command generator.
Also it's nice to see that the test output is the same even when the
value is generated in a different place.
The 'file.password-secret' injection should be used only if we are using
the old formatter. When formatting the source string from the JSON
properties, the property should be added there.
Also drop the comment which refers to stuff that will not be used in
libvirt since -blockdev is the way to go.
Qemu has now an internal mechanism for locking images to fix specific
cases of disk corruption. This requires libvirt to mark the image as
shared so that qemu lifts certain restrictions.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1378242
'share-rw' for the disk device configures qemu to allow concurrent
access to the backing storage.
The capability is checked in various supported disk frontend buses since
it does not make sense to partially backport it.
Creating a snapshot would introduce a possibly unsupported member for
sharing into the backing chain. Add a check to prevent that from
happening.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1511480
Disk sharing between two VMs may corrupt the images if the format driver
does not support it. Check that the user declared use of a supported
storage format when they want to share the disk.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1511480
Storage source format backing a shared device (e.g. running a cluster
filesystem) needs to support the sharing so that metadata are not
corrupted. Add a central function for checking this.
Since we already have such support for libxl all we need is qemu
driver adjustment. And a test case.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
This capability says if qemu is capable of specifying distances
between NUMA nodes on the command line. Unfortunately, there's no
real way to check this and thus we have to go with version check.
QEMU introduced this in 0f203430dd8 (and friend) which was
released in 2.10.0.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
When QEMU dies, we read its output stored in a log file and use it for
reporting a hopefully useful error. However, virReportError will trim
the message to (VIR_ERROR_MAX_LENGTH - 1) characters, which means the
end of the log (which likely contains the error message we want to
report) may get lost. We should trim the beginning of the log instead.
https://bugzilla.redhat.com/show_bug.cgi?id=1335534
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
When reading QEMU log for reporting it as an error message, we want to
skip "char device redirected to" line. However, this string is not
printed at the beginning of a line, which means STRPREFIX will never
find it.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Historically we've formatted a lot of the attributes of a disk (disk
geometry, etc) with -drive. Since we use -device now, they should be
formatted there. Extract them to a separate function for keeping
compatibility with SDcards which still use only -drive.
Start this by moving the geometry into a separate function.
When doing block commit we need to allow write for members of the
backing chain so that we can commit the data into them.
qemuDomainDiskChainElementPrepare was used for this which since commit
786d8d91b4 calls qemuDomainNamespaceSetupDisk which has very adverse
side-effects, namely it relabels the nodes to the same label it has in
the main namespace. This was messing up permissions for the commit
operation since its touching various parts of a single backing chain.
Since we are are actually not introducing new images at that point add a
flag for qemuDomainDiskChainElementPrepare which will refrain from
calling to the namespace setup function.
Calls from qemuDomainSnapshotCreateSingleDiskActive and
qemuDomainBlockCopyCommon do introduce new members all calls from
qemuDomainBlockCommit do not, so the calls are anotated accordingly.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1506072
https://bugzilla.redhat.com/show_bug.cgi?id=1434451
Just like in 9324f67a57 we need to put default sata alias
(which is hardcoded to "ide", obvious, right?) onto the command
line instead of the one provided by user.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function only queries domain @def. It doesn't change it.
Therefore it should take const pointer.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The compiler can warn us if we add a value to the
virDomainChrSerialTargetType enumeration but forget to handle
it properly in the code. Let's take advantage of that.
This commit is best viewed with 'git diff -w'.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Add a separate capability for the sclplmconsole device, and check it
specifically instead of using QEMU_CAPS_DEVICE_SCLPCONSOLE for that too.
Signed-off-by: Pino Toscano <ptoscano@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Give a better name to the capability for the sclpconsole device.
Signed-off-by: Pino Toscano <ptoscano@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Up until now we assumed the spapr-vty device would always be
present, which is not very nice. Check for its availability before
using it instead.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Starting from qemu 2.11, the `-device vmcoreinfo` will create a fw_cfg
entry for a guest to store dump details, necessary to process kernel
dump with KASLR enabled and providing additional kernel details.
In essence, it is similar to -fw_cfg name=etc/vmcoreinfo,file=X but in
this case it is not backed by a file, but collected by QEMU itself.
Since the device is a singleton and shouldn't use additional hardware
resources, it is presented as a <feature> element in the libvirt
domain XML.
The device is arm/x86 only for now (targets that support fw_cfg+dma).
Related to:
https://bugzilla.redhat.com/show_bug.cgi?id=1395248
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Truncate the output so that it is only as big as is needed to fit all
the bits, not all the units from the map. This will be needed in the
future in order to properly format bitmaps for kernel's sysfs files.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
This follows the virBitmapToData() function and, similarly to
virBitmapNewData(), we'll be able to have virBitmapNewString() later
on without name confusion.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
