The postParse callback is the correct place to generate default values
that should be present in offline XML.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
QEMU changed the error message to:
"Tray of device 'drive-sata0-0-1' is not open"
and they may change the error massage in the future.
This updates the code to not depend on the text from the error message
but only on error itself.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
When reading in an XML definition for a SCSI target device, the name
property of struct scsi_target refers to the @target element.
Let's fix this obvious typo and also extend the XML schema to provide
validation.
Signed-off-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Until now, the libxl driver ignored any <hap> setting in domain XML
and deferred to libxl, which enables hap if not specified. While
this is a good default, it prevents disabling hap if desired.
This change allows disabling hap with <hap state='off'/>. hap is
explicitly enabled with <hap/> or <hap state='on/>. Absense of <hap>
retains current behavior of deferring default state to libxl.
hap is enabled by default in xm and xl config and usually only
specified when it is desirable to disable hap (hap = 0). Change
the xm,xl <-> xml converter to behave similarly. I.e. only
produce 'hap = 0' when <hap state='off'/> and vice versa.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Most hypervisors use Hardware Assisted Paging by default and don't
require specifying the feature in domain conf. But some hypervisors
support disabling HAP on a per-domain basis. To enable HAP by default
yet provide a knob to disable it, extend the <hap> feature with a
'state=on|off' attribute, similar to <pvspinlock> and <vmport> features.
In the absence of <hap>, the hypervisor default (on) is used. <hap>
without the state attribute would be the same as <hap state='on'/> for
backwards compatibility. And of course <hap state='off'/> disables hap.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
The function already takes two bool arguments, switching to flags makes
it a lot easier to read. Especially in case we need to add another
boolean in the future.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
In post-copy mode none of the hosts has a complete guest state and
rolling back migration is impossible. Thus aborting it would be
equivalent to destroying the domain.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When migration fails in the post-copy mode, it's impossible to just kill
the destination domain and resume the source since the source no longer
contains current guest state. Let's mark domains on both sides as
VIR_DOMAIN_PAUSED_POSTCOPY_FAILED to let the upper layer decide what to
do with them.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When destination libvirtd is restarted during migration in Finish phase
just after the point we started guest CPUs, we should not kill the
domain.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Migration enters "postcopy-active" state after QEMU switches to
post-copy and pauses guest CPUs. From libvirt's point of view this state
is similar to "completed" because we need to transfer guest execution to
the destination host.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
To use post-copy one has to start the migration with
VIR_MIGRATE_POSTCOPY flag and, while migration is in progress, call
virDomainMigrateStartPostCopy() to switch from pre-copy to post-copy.
Signed-off-by: Cristian Klein <cristiklein@gmail.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
VIR_DOMAIN_EVENT_SUSPENDED_POSTCOPY and VIR_DOMAIN_PAUSED_POSTCOPY are
used on the source host once migration enters post-copy mode (which
means the domain gets paused on the source. After the destination host
takes over the execution of the domain, its virtual CPUs are resumed and
the domain enters VIR_DOMAIN_RUNNING_POSTCOPY state and
VIR_DOMAIN_EVENT_RESUMED_POSTCOPY event is emitted.
In case migration fails during post-copy mode and none of the hosts have
complete state of the domain, both domains will remain paused with
VIR_DOMAIN_PAUSED_POSTCOPY_FAILED reason and an upper layer may decide
what to do.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
This allows setting the address in host and/or network order and makes
the naming consistent. Now you don't need to call [hn]to[nh]l()
functions as that is taken care of by these functions. Also, now
the *NetOrder take the address in network order, the other functions in
host order so the naming and usage is consistent. Some places were
having the address in network order and calling ntohl() just so the
original function can call htonl() again. This makes it nicer to read.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If a <graphics type='spice'> has no port nor tlsPort set, the generated
QEMU command line will contain -spice port=0.
This is later going to be ignored by spice-server, but it's better not
to add it at all in this situation.
As an empty -spice is not allowed, we still need to append port=0 if we
did not add any other argument.
The end goal is to avoid adding -spice port=0,addr=127.0.0.1 to QEMU command
line when no SPICE port is specified in libvirt XML.
Currently, the code relies on port=xx to always be present, so subsequent
args can be unconditionally appended with a leading ','. Since port=0
will no longer be added in a subsequent commit, we append a ',' to every
arg instead of prepending, and remove the last one before adding it to
the arg list.
It's just a combination of AddImplicitControllers, and AddConsoleCompat.
Every caller that wants ImplicitControllers also wants the ConsoleCompat
AFAICT, so lump them together. We also need it for future patches.
Judging by how the whitelist has skewed quite far from the original
error message, I think it's better to just drop these.
If someone wants to revive this check I suggest implementing it on
a per-HV driver basis with PostParse callbacks.
If we expose this information, which is one byte in every PCI config
file, we let all mgmt apps know whether the device itself is an endpoint
or not so it's easier for them to decide whether such device can be
passed through into a VM (endpoint) or not (*-bridge).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Best viewed with '-w' as this is just an adjustment for future patch to
be readable without that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The implementation is pretty straightforward. Moreover, because
of the nature of things, gethostbyname_r and gethostbyname2_r can
be implemented at the same time too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This is a missing counterpart for virSocketAddrSetIPv4Addr()
and is going to be needed later in the tests.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function is going to be used later in such context where the
argument makes no sense. Teach this function to cope with that
instead of the caller having to deal with passing some dummy
argument.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
These functions are going to be reused very shortly. So instead
of duplicating the code, lets move them into utils module.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Commit id '4f846170' added printing of a new field 'part_separator';
however, neglected to do so when there was an "freeExtent" defined
for the device (as there would be when the disk pool was started).
This patch adjusts the logic to appropriately format the device path and
if there the part_separator attribute.
Commit 'ef2ab8fd' moved just the virDomainConfNWFilterTeardown and left
the logic to save/restore the current error essentially doing nothing
in the error path for qemuBuildCommandLine. So move it to where it
was meant to be.
Although the original code would reset the filter on command creation
errors after building the network command portion and commit 'ef2ab8fd'
altered that logic, the teardown is called during qemuProcessStop from
virDomainConfVMNWFilterTeardown and that code has the save/restore
last error logic, so just allow that code to handle the teardown rather
than running it twice. The qemuProcessStop would be called in the failure
path of qemuBuildCommandLine.
We include the file in plenty of places. This is mostly due to
historical reasons. The only place that needs something from the
header file is storage_backend_fs which opens _PATH_MOUNTED. But
it gets the file included indirectly via mntent.h. At no other
place in our code we need _PATH_.*. Drop the include and
configure check then.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Missing modules is a common expected scenario for most libvirt usage on
RPM distributions like Fedora, so it doesn't really warrant logging at
WARN level. Use INFO instead
https://bugzilla.redhat.com/show_bug.cgi?id=1274849
It does not have a suffix ByName because there are no other means of
looking up the server and since the name is known, this should be the
preferred one.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Mostly it is just passing new parameter here and there. In case
of zero value we fallback to auto selecting port and thus keep
backward compatibility.
Also we need to fix places of auto selected port managment.
We should bother only when auto selected was done that is
when externally specified port is not 0.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1271183
We only wait 0.5 seconds for the session daemon to start up and present
its socket, which isn't sufficient for many users. Bump up the sleep
interval and retry amount so we wait for a total of 5.0 seconds.
Refactor series 0b231195 worked with virLogDestination type which, depending
on the compiler, might be (and probably will be) an unsigned data type.
However, virEnumFromString may return -1 in case of an error. So, when enum
happens to be unsigned, some compilers will naturally complain about foo:
'if (foo < 0)'
Each version of virtuozzo supports only one type of SCSI controller
So if we add disk on SCSI bus, we should set SCSI controller model.
We can take it from vzCapabilities structure.
Because Vz6 supports SCSI(BUSLOGIC), IDE and SATA controllers only and
Vz7 supports SCSI(VIRTIO_SCSI) and IDE only we add list of supported
controllers and scsi models to vzCapabilities structure.
When a new connection opens, we select proper capabilities values according
to Virtuozzo version and check them in XMLPostParse.
Signed-off-by: Maxim Nestratov <mnestratov@virtuozzo.com>
We should report correct disk format depending on vz version and domain type.
Since we support only one disk format for each domain type, we can take it
from vzCapabilities structure.
