This patch provides support for the new watchdog model "diag288".
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
This patch provides support for a new watchdog action "inject-nmi" which
allows to define an inject of a non-maskable interrupt into a guest.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
The acl.html file includes aclperms.htmlinc which is generated.
However, acl.html is generated too from acl.html.tmp. And in fact,
this is the place where the aclperms file is needed. Fix the
dependency in Makefile.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Currently the grammar uses "none" for a "valid" Disk Storage Pool
format type; however, virStoragePoolFormatDisk uses "unknown" so
virt-xml-validate will fail to validate when "unknown" is found
The type='scsi' parameter of an address element is ignored
if placed within a hostdev section, and rejected by the XML
schema used by virt-xml-validate. Remove it from the doc,
and correct a typo in the remaining address arguments.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Defining a domain with a SCSI disk attached via a hostdev
tag and a source address unit value longer than two digits
causes an error when editing the domain with virsh edit,
even if no changes are made to the domain definition.
The error suggests invalid XML, somewhere:
# virsh edit lmb_guest
error: XML document failed to validate against schema:
Unable to validate doc against /usr/local/share/libvirt/schemas/domain.rng
Extra element devices in interleave
Element domain failed to validate content
The virt-xml-validate tool fails with a similar error:
# virt-xml-validate lmb_guest.xml
Relax-NG validity error : Extra element devices in interleave
lmb_guest.xml:17: element devices: Relax-NG validity error :
Element domain failed to validate content
lmb_guest.xml fails to validate
The hostdev tag requires a source address to be specified,
which includes bus, target, and unit address attributes.
According to the SCSI Architecture Model spec (section
4.9 of SAM-2), a LUN address is 64 bits and thus could be
up to 20 decimal digits long. Unfortunately, the XML
schema limits this string to just two digits. Similarly,
the target field can be up to 32 bits in length, which
would be 10 decimal digits.
# lsscsi -xx
[0:0:19:0x4022401100000000] disk IBM 2107900 3.44 /dev/sda
# lsscsi
[0:0:19:1074872354]disk IBM 2107900 3.44 /dev/sda
# cat lmb_guest.xml
<domain type='kvm'>
<name>lmb_guest</name>
<memory unit='MiB'>1024</memory>
...trimmed...
<devices>
<controller type='scsi' model='virtio-scsi' index='0'/>
<hostdev mode='subsystem' type='scsi'>
<source>
<adapter name='scsi_host0'/>
<address bus='0' target='19' unit='1074872354'/>
</source>
</hostdev>
...trimmed...
Since the reference unit and target fields are used in
several places in the XML schema, create a separate one
specific for SCSI Logical Units that will permit the
greater length. This permits both the validation utility
and the virsh edit command to succeed when a hostdev
tag is included.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1220527
This type of information defines attributes of a system
baseboard. With one exception: board type is yet not implemented
in qemu so it's not introduced here either.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since the background for Admin API is merged upstream, we are bumping
the minor release version as discussed previously
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
No online docs are build from it since it doesn't really fit into our
document structure and new page will need to be created for it, but this
is at least a heads-up commit for easier parsing in order to build some
documentation (or python bindings) later on.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1186969
When generating the path to the dir for a CIFS/Samba driver, the code
would generate a source path for the mount using "%s:%s" while the
mount.cifs expects to see "//%s/%s". So check for the cifsfs and
format the source path appropriately.
Additionally, since there is no means to authenticate, the mount
needs a "-o guest" on the command line in order to anonymously mount
the Samba directory.
Commit id '887dd362' added support for a netfs pool format type 'cifs'
and 'gluster' in order to add rng support for Samba and glusterfs netfs
pools. Originally, the CIFS type support was added as part of commit
id '61fb6979'. Eventually commit id 'b325be12' fixed the gluster rng
definition to match expectations.
As it turns out the CIFS rng needed a similar change since the directory
path is not an absDirPath, rather just a dirPath will be required.
https://bugzilla.redhat.com/show_bug.cgi?id=1021480
Seems the property has been deprecated for qemu, although seemingly ignored.
This patch enforces from a libvirt perspective that a scsi-block 'lun'
device should not provide the 'serial' property.
https://bugzilla.redhat.com/show_bug.cgi?id=1228007
When attaching a scsi volume lun via the attach-device --config or
--persistent options, there was no translation of the source pool
like there was for the live path, thus the attempt to modify the config
would fail since not enough was known about the disk.
I see no reason to duplicate this list of architectures. This also allows
more guest architectures to be used with libvirt (like the mips64el qemu
machine I am trying to run).
Signed-off-by: James Cowgill <james410@cowgill.org.uk>
This patch adds the support of queues attribute of the driver element
for vhost-user interface type. Example:
<interface type='vhostuser'>
<mac address='52:54:00:ee:96:6d'/>
<source type='unix' path='/tmp/vhost2.sock' mode='client'/>
<model type='virtio'/>
<driver queues='4'/>
</interface>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1207692
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If a macro has a string value, the @string attribute will contain the
value. Otherwise @string attribute will be missing.
For example, the following macro definition from libvirt-domain.h:
/**
* VIR_MIGRATE_PARAM_URI:
* ...
*/
# define VIR_MIGRATE_PARAM_URI "migrate_uri"
will result in
<macro name='VIR_MIGRATE_PARAM_URI' file='libvirt-domain' string='migrate_uri'>
<info><![CDATA[...]]></info>
</macro>
https://bugzilla.redhat.com/show_bug.cgi?id=1229199
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
The network name is currently of type "deviceName" but it should be
"text" as name is defined in the network.rng.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
The guest firmware provides the same functionality as the pvpanic
device, and the relevant element should always be present in the
domain XML to reflect this fact, so add it after parsing the
definition if it wasn't there already.
The guest firmware provides the same functionality as the pvpanic
device, which is not available in QEMU on pSeries, so the domain
XML should be allowed to contain the <panic> element.
On the other hand, unlike the pvpanic device, the guest firmware
can't be configured, so report an error if an address has been
provided in the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182388
The XML parser sets a default <mode> if none is explicitly passed in.
This is then used at pool/vol creation time, and unconditionally reported
in the XML.
The problem with this approach is that it's impossible for other code
to determine if the user explicitly requested a storage mode. There
are some cases where we want to make this distinction, but we currently
can't.
Handle <mode> parsing like we handle <owner>/<group>: if no value is
passed in, set it to -1, and adjust the internal consumers to handle
it.
- Don't redocument the permissions fields for backingstore, just point to
the volume docs.
- Clarify that owner/group are inherited from the parent directory at
volume create/pool build time.
- Clarify that <permissions> fields report runtime values too
In the upstream discussion on creating a github mirror [1], it turned
out that there are some read-only mirrors of our repository. Lets
advertise them on our downloads page. But do it wisely and discourage
people in sending a pull requests on GitHub.
1: https://www.redhat.com/archives/libvir-list/2015-May/msg00775.html
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of netcf-0.2.8, netcf supports configuring multipl IPv4 addresses,
as well as simultaneously configuring dhcp and static IPv4 addresses,
on a single interface. This patch updates libvirt's interface.rng to
allow such configurations.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1223688
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Like usb-serial, the pci-serial device allows a serial device to be
attached to PCI bus. An example XML looks like this:
<serial type='dev'>
<source path='/dev/ttyS2'/>
<target type='pci-serial' port='0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</serial>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Two new domain configuration XML elements are added to enable/disable
the protected key management operations for a guest:
<domain>
...
<keywrap>
<cipher name='aes|dea' state='on|off'/>
</keywrap>
...
</domain>
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1171984https://bugzilla.redhat.com/show_bug.cgi?id=1188463
Remove the check for the source host name for iSCSI source XML processing
declaring duplicate sources when the source device path and if present the
initiator of a proposed storage pool matches an existing storage pool.
The backend iSCSI storage driver uses 'iscsiadm --mode session' to query
available iscsid target sessions. The output displayed is the IP address
and the IQN (target path) of known targets. The displayed IP address
is a resolved address based on the session --login. Additionally, iscsid
keeps track of the various ways to define the host name (IPv4 Address,
IPv6 Address, /etc/hosts, etc.) for that IQN (see output of an 'iscsiadm
--mode node'). If an incoming IQN matches and the host name provided by
libvirt is resolved to the existing IQN, then iscsid will "reuse" the
session. Although libvirt could do the same name resolution, if there
is a difference, iscsid could still declare two seemingly different sources
to be the same and not create a new session which means libvirt now has
two storage pools looking at the same source. Thus to avoid any strange
host name resolution issues, just rely on iscsid for that and do not
allow multiple pools on the same host to use the same device path (IQN).
Some platforms, like aarch64, don't have APIC but GIC. So there's
no reason to have <apic/> feature turned on. However, we are
still missing <gic/> feature. This commit introduces the feature
to XML parser and formatter, adds documentation and updates RNG
schema.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
A new feature that can be turned on or off.
The QEMU machine vmport option allows to set the VMWare IO port
emulation. This emulation is useful for absolute pointer input when the
guest has vmware input drivers, and is enabled by default for kvm.
However it is unnecessary for Spice-enabled VM, since the agent already
handles absolute pointer and multi-monitors. Furthermore, it prevents
Spice from switching to relative input since the regular ps/2 pointer
driver is replaced by the vmware driver. It is thus advised to disable
vmport when using a Spice VM. This will permit the Spice client to
switch from absolute to relative pointer, as it may be required for
certain games or applications.
The phyp driver stuffed it into a DomainDefPtr during its attachdevice
routine, but the value is never advertised via capabilities so it should
be safe to drop.
Have the phyp driver use OSTYPE_LINUX, which is what it advertises via
capabilities.
With iothreadid's allowing any 'id' value for an iothread_id, the
iothreadsched code needs a slight adjustment to allow for "any"
unsigned int value in order to create the bitmap of ids that will
have scheduler adjustments. Adjusted the doc description as well.
Remove the iothreadspin array from cputune and replace with a cpumask
to be stored in the iothreadids list.
Adjust the test output because our printing goes in order of the iothreadids
list now.
Adding a new XML element 'iothreadids' in order to allow defining
specific IOThread ID's rather than relying on the algorithm to assign
IOThread ID's starting at 1 and incrementing to iothreads count.
This will allow future patches to be able to add new IOThreads by
a specific iothread_id and of course delete any exisiting IOThread.
Each iothreadids element will have 'n' <iothread> children elements
which will have attribute "id". The "id" will allow for definition
of any "valid" (eg > 0) iothread_id value.
On input, if any <iothreadids> <iothread>'s are provided, they will
be marked so that we only print out what we read in.
On input, if no <iothreadids> are provided, the PostParse code will
self generate a list of ID's starting at 1 and going to the number
of iothreads defined for the domain (just like the current algorithm
numbering scheme). A future patch will rework the existing algorithm
to make use of the iothreadids list.
On output, only print out the <iothreadids> if they were read in.
In a lot places we use path like this:
$(srcdir)/../src/....
when in fact it can be:
$(top_srcdir)/src/
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
If this enviroment variable is set, the virTestCompareToFile helper
will overwrite the file content we are comparing against, if the
file doesn't exist or it doesn't match the expected input.
This is useful when adding new test cases, or making changes that
generate a lot of output churn.
The PortNumber data type is declared to derive from 'short'.
Unfortunately this is an signed type, so validates the range
[-32,768, 32,767] which excludes valid port numbers between
32767 and 65535.
We can't use 'unsignedShort', since we need -1 to be a valid
port number too.
This change is to use 'int' and set an explicit max boundary
instead of relying on the data types' built-in max.
One of the existing tests is changed to use a high port number
to validate the schema.
https://bugzilla.redhat.com/show_bug.cgi?id=1214664
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
According to docs, using 'lun' as a value for device attribute is only valid
with disk types 'block' and 'network'. However current RNG schema also allows
a combination type='file' device='lun' which results in a successfull
xml validation, but fails at qemuBuildCommandLine.
Besides fixing the RNG schema, this patch also adds a qemuxml2argvtest
for this case.
https://bugzilla.redhat.com/show_bug.cgi?id=1210669
