The current code uses virCgroupNew() as a single point of entry and
calls into virCgroupDetect() as well. Both have logic for several paths
which is difficult to figure out.
Extract the actually used code path from the two functions to make
it obvious what's happening in this case.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
It is only used for debug and error purposes which can be easily
replaced by @placement.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
After converting all DIR* to g_autoptr(DIR), many cleanup: labels
ended up just having "return ret", and every place that set ret would
just immediately goto cleanup. Remove the cleanup label and its
return, and just return the set value immediately, thus eliminating
the need for the return variable itself.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
All of these conversions are trivial - VIR_DIR_CLOSE() (aka
virDirClose()) is called only once on the DIR*, and it happens just
before going out of scope.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Remove 'cleanup' label and simplify remembering of the returned value
from the callback.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Rewrite using GHashTable which already has interfaces for using a number
as hash key. Glib's implementation doesn't copy the key by default, so
we need to allocate it, but overal the interface is more suited for this
case.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
virCgroupKillRecursive sneakily initializes 'ret' to 0 rather than the
usual -1. 401030499b moved an error condition but didn't actually
modify 'ret' return the proper error code.
Fixes: 401030499b
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
As preparation for g_autoptr() we need to change the function to take
only virCgroupPtr.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Jonathon Jongsma <jjongsma@redhat.com>
Both accept a NULL value gracefully and virStringFreeList
does not zero the pointer afterwards, so a straight replace
is safe.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Martin Kletzander <mkletzan@redhat.com>
The term "access control list" better describes the concept involved.
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Instead of the following pattern:
type ret;
...
ret = func();
return ret;
we can use:
return func()
directly.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Another vircgroup helper to avoid code repetition between
the LXC and QEMU driver.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
qemuSetupCgroupVcpuBW() and lxcSetVcpuBWLive() shares the
same code to set CPU CFS period and quota. This code can be
moved to a new virCgroupSetupCpuPeriodQuota() helper to
avoid code repetition.
A similar code is also executed in virLXCCgroupSetupCpuTune(),
but without the rollback on error. Use the new helper in this
function as well since the 'period' rollback, if not a
straight improvement for virLXCCgroupSetupCpuTune(), is
benign. And we end up cutting more code repetition.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The code that calls virCgroupSetCpuShares() and virCgroupGetCpuShares()
is repeated in 4 different places. Let's put it in a new
virCgroupSetupCpuShares() to avoid code repetition.
There's a reason of why we execute a Get in the same value we
just executed Set, explained in detail by commit 97814d8ab3.
Let's add a gist of the reasoning behind it as a comment in
this new function as well.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The code from qemuSetupCgroupCpusetCpus() and virLXCCgroupSetupCpusetTune()
can be centralized in a new helper called virCgroupSetupCpusetCpus().
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Previous patch moved all duplicated code that were setting
and getting BlkioDevice parameters to vircgroup.c. We can
turn them into static and spare a few symbols in
libvirt_private.syms.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The current use of the functions that set and get
BlkioDevice attributes is doing a set(), followed by
a get() of the same parameter right after. This is done
because there is no guarantee that the kernel will accept
the desired value given by the set() call, thus we need to
execute a get() right after to get the actual value.
This patch adds helpers inside vircgroup.c to execute these
operations. Next patch will use these helpers to reduce
code repetition in LXC and QEMU files.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
All our supported Linux distros now have this header.
It has never existed on FreeBSD / macOS / Mingw.
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The strchrnul function doesn't exist on Windows and rather
than attempt to implement it, it is simpler to just avoid
its usage, as any callers are easily adapted.
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
If we get a user reporting this error message being shown it's pretty
useless in terms of actually debugging it since we don't know which hash
and which key are actually subject to the error.
This patch adds a new hash table callback which formats the
user-readable version of the hash key and reports it in the new message
which will look like:
"Duplicate hash table key 'blah'"
That way we will at least have an anchor point where to start the
search.
There are two special implementations of keys which are numeric so we
add specific printer functions for them.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
This previous commit introduced a simpler free callback for
hash data with only 1 arg, the value to free:
commit 49288fac96
Author: Peter Krempa <pkrempa@redhat.com>
Date: Wed Oct 9 15:26:37 2019 +0200
util: hash: Add possibility to use simpler data free function in virHash
It missed two functions in the hash table code which need
to call the alternate data free function, virHashRemoveEntry
and virHashRemoveSet.
After the previous patch though, there is no code that
makes functional use of the 2nd key arg in the data
free function. There is merely one log message that can
be dropped.
We can thus purge the current virHashDataFree callback
entirely, and rename virHashDataFreeSimple to replace
it.
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Call first virCgroupNew on the parent group virCgroupNewPartition if
it is available on before the creation of the child group. This
ensures that the creation of a first level group on the unified
architecture, as the check at virCgroupV2ParseControllersFile as the
parent file is there.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1760233
Signed-off-by: Miguel Ángel Arruga Vivas <rosen644835@gmail.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
So the issue here is that you can end up with configuration where
you have cgroup v1 and v2 enabled at the same time and the devices
controllers is enabled for cgroup v1.
In cgroup v2 there is no devices controller, the device access is
controlled using BPF and since it is not a cgroup controller both
of them can exists at the same time and both of them are applied while
resolving access to devices.
In order to avoid configuring both BPF and cgroup v1 devices we will
use BPF if possible and otherwise fallback to cgroup v1 devices.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Introduce a new type virHashDataFreeSimple which has only a void * as
argument for cases when knowing the name of the entry when freeing the
hash entry is not required.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
ACKed-by: Eric Blake <eblake@redhat.com>
Replace all occurrences of
if (VIR_STRDUP(a, b) < 0)
/* effectively dead code */
with:
a = g_strdup(b);
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Provide some consistency over error message variable name and usage
when saving error messages across possible other errors or possibility
of resetting of the last error.
Instead of virSaveLastError paired up with virSetError and virFreeError,
we should use the newer virErrorPreserveLast and virRestoreError.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Since commit 44e7f02915
util: rewrite auto cleanup macros to use glib's equivalent
VIR_AUTOFREE is just an alias for g_autofree. Use the GLib macros
directly instead of our custom aliases.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Use G_GNUC_UNUSED from GLib instead of ATTRIBUTE_UNUSED.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
The usleep function was missing on older mingw versions, but we can rely
on it existing everywhere these days. It may only support times upto 1
second in duration though, so we'll prefer to use g_usleep instead.
The commandhelper program is not changed since that can't link to glib.
Fortunately it doesn't need to build on Windows platforms either.
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
When creating new group for cgroups v2 the we cannot check
cgroups.controllers for that cgroup because the directory is created
later. In that case we should check cgroups.subtree_control of parent
group to get list of controllers enabled for child cgroups.
In order to achieve that we will prefer the parent group if it exists,
the current group will be used only for root group.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Commit d5572f62e3 forgot to add maxthreads to the non-Linux definition
of the function, thus breaking the MinGW build.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Some VM configurations may result in a large number of threads created by
the associated qemu process which can exceed the system default limit. The
maximum number of threads allowed per process is controlled by the pids
cgroup controller and is set to 16k when creating VMs with systemd's
machined service. The maximum number of threads per process is recorded
in the pids.max file under the machine's pids controller cgroup hierarchy,
e.g.
$cgrp-mnt/pids/machine.slice/machine-qemu\\x2d1\\x2dtest.scope/pids.max
Maximum threads per process is controlled with the TasksMax property of
the systemd scope for the machine. This patch adds an option to qemu.conf
which can be used to override the maximum number of threads allowed per
qemu process. If the value of option is greater than zero, it will be set
in the TasksMax property of the machine's scope after creating the machine.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
virCgroupRemove return -1 when removing cgroup failed.
But there are retry code to remove cgroup in QemuProcessStop:
retry:
if ((ret = qemuRemoveCgroup(vm)) < 0) {
if (ret == -EBUSY && (retries++ < 5)) {
usleep(200*1000);
goto retry;
}
VIR_WARN("Failed to remove cgroup for %s",
vm->def->name);
}
The return value of qemuRemoveCgroup will never be equal to "-EBUSY",
so change the return value of virCgroupRemove if failed.
Signed-off-by: Wang Yechao <wang.yechao255@zte.com.cn>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Because of a systemd delegation policy [1] we should not write to any
cgroups files owned by systemd which in case of cgroups v2 includes
'cgroups.subtree_control'.
systemd will enable controllers automatically for us to have them
available for VM cgroups.
[1] <https://github.com/systemd/systemd/blob/master/docs/CGROUP_DELEGATION.md>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
This reverts commit 7bca1c9bdc.
As it turns out it's not a good idea on systemd hosts. The root
cgroup can have all controllers enabled but they don't have to be
enabled for sub-cgroups.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
This affects only cgroups v2 where enabled controllers are not based on
available mount points but on the list provided in cgroup.controllers
file. However, moving it will fill in placement as well, so it needs
to be freed together with mount point if we don't need that controller.
Before this patch we were assuming that all controllers available in
root cgroup where available in all other sub-cgroups which was wrong.
In order to fix it we need to move the cgroup controllers detection
after cgroup placement was prepared in order to build correct path for
cgroup.controllers file.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
In cgroups v2 we don't have to detect available controllers every single
time if we are creating a new cgroup based on parent cgroup.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
If we need to get a path of specific file and we need to check its
existence before we use it then we can reuse that path to get value
for specific device. This way we will not build the path again in
virCgroupGetValueForBlkDev.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
If we need to get a path of specific file and we need to check its
existence before we use it then we can reuse that path to get/set
values instead of calling the existing get/set value functions which
would be building the path again.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
virCgroup struct is always defined and the free function is not calling
anything that would require OS supporting cgroups.
This fixes an issue if we try to start a VM with QEMU binary that
doesn't support QXL. The start operation will fail in
qemuProcessStartValidateVideo() which will set correct error message,
but later in one of the cleanup paths we will call
qemuDomainObjPrivateDataClear() which always calls virCgroupFree()
and that will fail on OS that doesn't support cgroups and it will
set a new error which will be eventually reported to user.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
