Implement the .domainGetHostname hypervisor driver API to get the
hostname of a running guest (needs VMware Tools).
Signed-off-by: Pino Toscano <ptoscano@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Neal Gompa <ngompa13@gmail.com>
The original motivation for adding virNetDevIPCheckIPv6Forwarding
(commit 00d28a78b5) was that networking routes would disappear when
ipv6 forwarding was enabled for an interface.
This is a fairly undocumented side-effect of the "accept_ra" sysctl
for an interface. 1 means the interface will accept_ra's if not
forwarding, 2 means always accept_RAs; but it is not explained that
enabling forwarding when accept_ra==1 will also clear any kernel RA
assigned routes, very likely breaking your networking.
The check to warn about this currently uses netlink to go through all
the routes and then look at the accept_ra status of the interfaces.
However, it has been noticed that this problem does not affect systems
where IPv6 RA configuration is handled in userspace, e.g. via tools
such as NetworkManager. In this case, the error message from libvirt
is spurious, and modifying the forwarding state will not affect the RA
state or disable your networking.
If you refer to the function rt6_purge_dflt_routers() in the kernel,
we can see that the routes being purged are only those with the
kernel's RTF_ADDRCONF flag set; that is, routes added by the kernel's
RA handling. Why does it do this? I think this is a Linux
implementation decision; it has always been like that and there are
some comments suggesting that it is because a router should be
statically configured, rather than accepting external configurations.
The solution implemented here is to convert the existing check into a
walk of /proc/net/ipv6_route (because RTF_ADDRCONF is apparently not
exposed in netlink) and look for routes with this flag set. We then
check the accept_ra status for the interface, and if enabling
forwarding would break things raise an error.
This should hopefully avoid "interactive" users, who are likely to be
using NetworkManager and the like, having false warnings when enabling
IPv6, but retain the error check for users relying on kernel-based
IPv6 interface auto-configuration.
Signed-off-by: Ian Wienand <iwienand@redhat.com>
Reviewed-by: Laine Stump <laine@redhat.com>
Reviewed-by: Cedric Bosdonnat <CBosdonnat@suse.com>
While we set up perf events for a shutoff domain and check the settings,
All of perf events are reported as 'disabled', unless we add --config,
This is redundant for a shutoff domain.
# virsh domstate $GUEST
shut off
# virsh perf --domain $GUEST
cmt : disabled
mbmt : disabled
mbml : disabled
......
# virsh perf --domain $GUEST --enable mbmt
mbmt : enabled
# virsh perf --domain $GUEST
cmt : disabled
mbmt : disabled
mbml : disabled
......
Use virDomainObjGetOneDefState instead of virDomainObjGetOneDef to fix
the issue. After patch, The perf event status of a shutoff domain is
reported correctly:
# virsh domstate $GUEST
shut off
# virsh perf --domain $GUEST
cmt : disabled
mbmt : disabled
mbml : disabled
......
# virsh perf --domain $GUEST --enable mbmt
mbmt : enabled
# virsh perf --domain $GUEST
cmt : disabled
mbmt : enabled
mbml : disabled
......
Signed-off-by: Lin Ma <lma@suse.de>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
It requires a guest agent configured and running in the domain's guest
OS, So check qemu agent during qemuDomainPMSuspendForDuration().
Signed-off-by: Lin Ma <lma@suse.de>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Note the use of g_clear_pointer(..., g_free) in ppc64DataClear and virCPUx86Baseline.
Signed-off-by: Tim Wiederhake <twiederh@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
When the guest agent isn't running, we still report success on a PM
suspend action even though we logged an error correctly, this is because
we poisoned the 'ret' value a few lines above.
Fixes: a663a86081
Signed-off-by: Erik Skultety <eskultet@redhat.com>
In v6.7.0-rc1~86 I've tried to fix a problem where we were not
detecting NUMA nodes properly because we misused behaviour of a
libnuma API and as it turned out the behaviour was correct for
hosts with 64 CPUs in one NUMA node. So I changed the code to use
nodemask_isset(&numa_all_nodes, ..) instead and it fixed the
problem on such hosts. However, what I did not realize is that
numa_all_nodes does not reflect all NUMA nodes visible to
userspace, it contains only those nodes that the process
(libvirtd) an allocate memory from, which can be only a subset of
all NUMA nodes. The bitmask that contains all NUMA nodes visible
to userspace and which one I should have used is: numa_nodes_ptr.
For curious ones:
4a22f22382
And as I was fixing virNumaGetNodeCPUs() I came to realize that
we already have a function that wraps the correct bitmask:
virNumaNodeIsAvailable().
Fixes: 24d7d85208
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1876956
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
This function was introduced in the 2.0.6 release which happened
in December 2010. I think it is safe to assume that all libnuma
we deal with have the function.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
virshDomainFree handles NULL pointers gracefully, so there's no need to
check the pointer before the call.
Signed-off-by: Yi Li <yili@winhong.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Since we no longer need to wait for IPv6 DAD to complete, we never
call this function.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
0f7436ca54 added code during virtual network startup to wait for DAD
(Duplicate Address Detection) to complete if there were any IPv6
addresses on the network. This wait was needed because (according to
the commit log) "created problems when [the "dummy" tap device] is set
to IFF_DOWN prior to DAD completing".
That commit in turn referenced commit db488c7917, which had added the
code to set the dummy tap device IFF_DOWN, commenting "DAD has
happened (dnsmasq waits for it)", and in its commit message pointed
out that if we just got rid of the dummy tap device this wouldn't be
needed.
Now that the dummy tap device has indeed been removed (commit
ee6c936fbb), there is no longer any need to set it IFF_DOWN, and thus
nothing requiring us to wait for DAD to complete. At any rate, with
the dummy tap device removed, leaving nothing else on the bridge when
it is first started, DAD never completes, leading to failure to start
any IPv6 network.
So, yes, this patch removes the wait for DAD completion, and IPv6
networks can once again start, and their associated dnsmasq process
starts successfully (this is the problem that the DAD wait was
originally intended to fix)
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
#useless_use_of_cat + avoid accidental substring matches.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The previous 11.3 image provided by Cirrus did not boot, but they have
now provided a working 11.4 image
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
We are currently adding -lutil and -lkvm to the linker using the
add_project_link_arguments method. On FreeBSD 11.4, this results in
build errors because the args appear too early in the command line.
We need to pass the libraries as dependencies so that they get placed
at the same point in the linker args as other dependencies.
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
* Add a period to the end of the page's introductory sentence.
* Correct a spelling error: "Evangalism"/"evangalise" -> "Evangelism"/"evangelize"
Signed-off-by: Matt Coleman <matt@datto.com>
Reviewed-by: Neal Gompa <ngompa13@gmail.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
The original author intended to write "different than".
"Different" is commonly followed by "from", "than", and "to".
Globally, "from" is the most common.
Signed-off-by: Matt Coleman <matt@datto.com>
Reviewed-by: Neal Gompa <ngompa13@gmail.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
This wires up support for using the new virt-ssh-helper binary with the ssh,
libssh and libssh2 protocols.
The new binary will be used preferentially if it is available in $PATH,
otherwise we fall back to traditional netcat.
The "proxy" URI parameter can be used to force use of netcat e.g.
qemu+ssh://host/system?proxy=netcat
or the disable fallback e.g.
qemu+ssh://host/system?proxy=native
With use of virt-ssh-helper, we can now support remote session URIs
qemu+ssh://host/session
and this will only use virt-ssh-helper, with no fallback. This also lets
the libvirtd process be auto-started, and connect directly to the
modular daemons, avoiding use of virtproxyd back-compat tunnelling.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Switch keyfile and netcat parameters, since the netcat path and
socket path are a logical pair that belong together. This patches
the other constructors.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
When accessing libvirtd over a SSH tunnel, the remote driver needs a way
to proxy the SSH input/output stream to a suitable libvirt daemon. This
is currently done by spawning netcat, pointing it to the libvirtd socket
path. This is problematic for a number of reasons:
- The socket path varies according to the --prefix chosen at build
time. The remote client is seeing the local prefix, but what we
need is the remote prefix
- The socket path varies according to remote env variables, such as
the XDG_RUNTIME_DIR location. Again we see the local XDG_RUNTIME_DIR
value, but what we need is the remote value (if any)
- The remote driver doesn't know whether it must connect to the legacy
libvirtd or the modular daemons, so must always assume legacy
libvirtd for back-compat. This means we'll always end up using the
virtproxyd daemon adding an extra hop in the RPC layer.
- We can not able to autospawn the libvirtd daemon for session mode
access
To address these problems this patch introduces the 'virtd-ssh-helper'
program which takes the URI for the remote driver as a CLI parameter.
It then figures out which daemon to connect to and its socket path,
using the same code that the remote driver client would on the remote
host's build of libvirt.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
We'll shortly want to reuse code for determining whether to connect to
the system or session daemon from places outside the remote driver
client. Pulling it out into a self contained function facilitates reuse.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
