The preferred syntax for boolean options is to set the value "on" or
"off". QEMU 7.1.0 will deprecate the short format we currently use.
The long format has been supported with -chardev since at least 1.5.3,
so we don't need to check for it.
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Simulate that the device is a cdrom when the path equals to /dev/cdrom
to provide testing for the 'host_cdrom' backend.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The 32-bit x86 binary is called qemu-system-i386, not
qemu-system-i686. This mistake across many test XML files was
not noticed because the mistake was also made in testutilsqemu.c
when mocking the capabilities.
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The '-realtime mlock' cmd line argument was introduced in QEMU
commit v1.5.0-rc0~190 which matches minimal QEMU version we
require. Therefore, the capability will always be present.
Apparently, nearly none of our xml2argv test cases had the
capability hence slightly bigger change under qemuxml2argvdata/.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
By default, qemu user's home dir points to '/' which shouldn't be used
at all. We therefore pass the HOME variable from the current variable
iff not running as SUID, which means that for systemd we never set it.
This patch makes sure, that for system QEMU this is always set to
libDir/<driver>, session mode is left untouched.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
For session mode, only XDG_CACHE_HOME is set, because we want to remain
integrating with services in user session, but for system mode, this
would have become reading/writing to '/' which carries the obvious issue
with permissions (also, '/' is the wrong location in 99.9% cases anyway).
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The split of ide-disk into the two separate devices was introduced by
qemu commit 1f56e32a7f4b3 released in qemu v0.15.
Note that when compared to the previous commit which made sure that no
disk related tests were touched, in this case it's not as careful.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
In commit f80eae8c2a I was too agresive in removing properties of
-drive for empty drives. It turns out that qemu actually persists the
state of 'readonly' and the throttling information even for the empty
drive.
Removing 'readonly' thus made qemu open any subsequent images added via
the 'change' command as RW which was forbidden by selinux thanks to the
restrictive sVirt label for readonly media.
Fix this by formating the property again and bump the tests and leave a
note detailing why the rest of the properties needs to be skipped.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
If a -drive has no image, using image properties makes qemu whine that
they should not be used.
This patch stops formating cache/readonly/... for empty drives
for the pre-blockdev syntax. Unfortunately those parameters can't be
added later when inserting media, but on the other hand qemu will start
with an empty drive.
Since we already were able to start a VM with such config previously due
to qemu ignoring them I've opted just to skip formatting them.
Additionally with -blockdev support it will work as expected as the
image properties will be formatted when adding the image itself which is
not possible without it.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1651457
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Upcomming change will influence CDROM with cache mode so add a test
case.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
The field was added in qemu v0.13.0-rc0-731-g1ca4d09ae0 so all supported
qemu versions now use it.
There's a LOT of test fallout as we did not use capabilities close
enough to upstream for many of our tests.
Several tests had a 'bootindex' variant. Since they'd become redundant
they are also removed here.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Implied by QEMU >= 1.2.0.
Delete this one first, because QEMU_CAPS_NODEFCONFIG is only used
when QEMU_CAPS_NO_USER_CONFIG is unsupported.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
We require QEMU >= 1.5.0, assume every QEMU supports it.
Sadly that does not let us trivially drop qemuMonitor's
priv->monJSON bool, because of qemuDomainQemuAttach.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Similarly to the previous commit, rename .args files.
The files were renamed using the following commands. From
qemuxml2argvdata:
for i in qemuxml2argv-*.args; do mv $i ${i#qemuxml2argv-}; done
and then (to fix broken symlinks) from qemuxml2argvdata and
qemuxml2xmloutdata:
for i in $(find . -xtype l); do \
ln -sf $(readlink $i | sed 's/qemuxml2argv-//') $i;
done
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
