Set the VIR_PCI_CONNECT_AGGREGATE_SLOT flag for pcie-root-ports so
that they will be assigned to all the functions on a slot.
Some qemu test case outputs had to be adjusted due to the
pcie-root-ports now being put on multiple functions.
For machinetypes with a pci-root bus (all legacy PCI), libvirt will
make a "fake" reservation for one extra slot prior to assigning
addresses to unaddressed PCI endpoint devices in the domain. This will
trigger auto-adding of a pci-bridge for the final device to be
assigned an address *if that device would have otherwise instead been
the last device on the last available pci-bridge*; thus it assures
that there will always be at least one slot left open in the domain's
bus topology for expansion (which is important both for hotplug (since
a new pci-bridge can't be added while the guest is running) as well as
for offline additions to the config (since adding a new device might
otherwise in some cases require re-addressing existing devices, which
we want to avoid)).
It's important to note that for the above case (legacy PCI), we must
check for the special case of all slots on all buses being occupied
*prior to assigning any addresses*, and avoid attempting to reserve
the extra address in that case, because there is no free address in
the existing topology, so no place to auto-add a pci-bridge for
expansion (i.e. it would always fail anyway). Since that condition can
only be reached by manual intervention, this is acceptable.
For machinetypes with pcie-root (Q35, aarch64 virt), libvirt's
methodology for automatically expanding the bus topology is different
- pcie-root-ports are plugged into slots (soon to be functions) of
pcie-root as needed, and the new endpoint devices are assigned to the
single slot in each pcie-root-port. This is done so that the devices
are, by default, hotpluggable (the slots of pcie-root don't support
hotplug, but the single slot of the pcie-root-port does). Since
pcie-root-ports can only be plugged into pcie-root, and we don't
auto-assign endpoint devices to the pcie-root slots, this means
topology expansion doesn't compete with endpoint devices for slots, so
we don't need to worry about checking for all "useful" slots being
free *prior* to assigning addresses to new endpoint devices - as a
matter of fact, if we attempt to reserve the open slots before the
used slots, it can lead to errors.
Instead this patch just reserves one slot for a "future potential"
PCIe device after doing the assignment for actual devices, but only
if the only PCI controller defined prior to starting address
assignment was pcie-root, and only if we auto-added at least one PCI
controller during address assignment. This assures two things:
1) that reserving the open slots will only be done when the domain is
initially defined, never at any time after, and
2) that if the user understands enough about PCI controllers that they
are adding them manually, that we don't mess up their plan by
adding extras - if they know enough to add one pcie-root-port, or
to manually assign addresses such that no pcie-root-ports are
needed, they know enough to add extra pcie-root-ports if they want
them (this could be called the "libguestfs clause", since
libguestfs needs to be able to create domains with as few
devices/controllers as possible).
This is set to reserve a single free port for now, but could be
increased in the future if public sentiment goes in that direction
(it's easy to increase later, but essentially impossible to decrease)
Now the a dmi-to-pci-bridge is automatically added just as it's needed
(when a pci-bridge is being added), we no longer have any need to
force-add one to every single Q35 domain.
Previously libvirt would only add pci-bridge devices automatically
when an address was requested for a device that required a legacy PCI
slot and none was available. This patch expands that support to
dmi-to-pci-bridge (which is needed in order to add a pci-bridge on a
machine with a pcie-root), and pcie-root-port (which is needed to add
a hotpluggable PCIe device). It does *not* automatically add
pcie-switch-upstream-ports or pcie-switch-downstream-ports (and
currently there are no plans for that).
Given the existing code to auto-add pci-bridge devices, automatically
adding pcie-root-ports is fairly straightforward. The
dmi-to-pci-bridge support is a bit tricky though, for a few reasons:
1) Although the only reason to add a dmi-to-pci-bridge is so that
there is a reasonable place to plug in a pci-bridge controller,
most of the time it's not the presence of a pci-bridge *in the
config* that triggers the requirement to add a dmi-to-pci-bridge.
Rather, it is the presence of a legacy-PCI device in the config,
which triggers auto-add of a pci-bridge, which triggers auto-add of
a dmi-to-pci-bridge (this is handled in
virDomainPCIAddressSetGrow() - if there's a request to add a
pci-bridge we'll check if there is a suitable bus to plug it into;
if not, we first add a dmi-to-pci-bridge).
2) Once there is already a single dmi-to-pci-bridge on the system,
there won't be a need for any more, even if it's full, as long as
there is a pci-bridge with an open slot - you can also plug
pci-bridges into existing pci-bridges. So we have to make sure we
don't add a dmi-to-pci-bridge unless there aren't any
dmi-to-pci-bridges *or* any pci-bridges.
3) Although it is strongly discouraged, it is legal for a pci-bridge
to be directly plugged into pcie-root, and we don't want to
auto-add a dmi-to-pci-bridge if there is already a pci-bridge
that's been forced directly into pcie-root.
Although libvirt will now automatically create a dmi-to-pci-bridge
when it's needed, the code still remains for now that forces a
dmi-to-pci-bridge on all domains with pcie-root (in
qemuDomainDefAddDefaultDevices()). That will be removed in a future
patch.
For now, the pcie-root-ports are added one to a slot, which is a bit
wasteful and means it will fail after 31 total PCIe devices (30 if
there are also some PCI devices), but helps keep the changeset down
for this patch. A future patch will have 8 pcie-root-ports sharing the
functions on a single slot.
