Change device type of a virtio channel from/to spicevmc is not a user
visible change. However, spicevmc channels use different default target
name than other virtio channels. To maintain ABI stability during this
change target name must be explicitly specified (and equal) in both
configurations.
The following config elements now support a <vlan> subelements:
within a domain: <interface>, and the <actual> subelement of <interface>
within a network: the toplevel, as well as any <portgroup>
Each vlan element must have one or more <tag id='n'/> subelements. If
there is more than one tag, it is assumed that vlan trunking is being
requested. If trunking is required with only a single tag, the
attribute "trunk='yes'" should be added to the toplevel <vlan>
element.
Some examples:
<interface type='hostdev'/>
<vlan>
<tag id='42'/>
</vlan>
<mac address='52:54:00:12:34:56'/>
...
</interface>
<network>
<name>vlan-net</name>
<vlan trunk='yes'>
<tag id='30'/>
</vlan>
<virtualport type='openvswitch'/>
</network>
<interface type='network'/>
<source network='vlan-net'/>
...
</interface>
<network>
<name>trunk-vlan</name>
<vlan>
<tag id='42'/>
<tag id='43'/>
</vlan>
...
</network>
<network>
<name>multi</name>
...
<portgroup name='production'/>
<vlan>
<tag id='42'/>
</vlan>
</portgroup>
<portgroup name='test'/>
<vlan>
<tag id='666'/>
</vlan>
</portgroup>
</network>
<interface type='network'/>
<source network='multi' portgroup='test'/>
...
</interface>
IMPORTANT NOTE: As of this patch there is no backend support for the
vlan element for *any* network device type. When support is added in
later patches, it will only be for those select network types that
support setting up a vlan on the host side, without the guest's
involvement. (For example, it will be possible to configure a vlan for
a guest connected to an openvswitch bridge, but it won't be possible
to do that for one that is connected to a standard Linux host bridge.)
Each interface has a single pointer to a filterref object. That
filterref can itself point to multiple other filterrefs, but at the
toplevel there is only one.
The parser had previously just silently overwritten earlier filterrefs
when a new one was encountered, so the interface was left with
whichever was the last filterref in the xml, ignoring all the
others. This patch logs an error when it sees more than one filterref.
Until now, all attributes in a <virtualport> parameter list that were
acceptable for a particular type, were also required. There were no
optional attributes.
One of the aims of supporting <virtualport> in libvirt's virtual
networks and portgroups is to allow specifying the group-wide
parameters in the network's virtualport, and merge that with the
interface's virtualport, which will have the instance-specific info
(i.e. the interfaceid or instanceid).
Additionally, the guest's interface XML shouldn't need to know what
type of network connection will be used prior to runtime - it could be
openvswitch, 802.1Qbh, 802.1Qbg, or none of the above - but should
still be able to specify instance-specific info just in case it turns
out to be applicable.
Finally, up to now, the parser for virtualport has always generated a
random instanceid/interfaceid when appropriate, making it impossible
to leave it blank (which is what's required for virtualports within a
network/portprofile definition).
This patch modifies the parser and formatter of the <virtualport>
element in the following ways:
* because most of the attributes in a virNetDevVPortProfile are fixed
size binary data with no reserved values, there is no way to embed a
"this value wasn't specified" sentinel into the existing data. To
solve this problem, the new *_specified fields in the
virNetDevVPortProfile object that were added in a previous patch of
this series are now set when the corresponding attribute is present
during the parse.
* allow parsing/formatting a <virtualport> that has no type set. In
this case, all fields are settable, but all are also optional.
* add a GENERATE_MISSING_DEFAULTS flag to the parser - if this flag is
set and an instanceid/interfaceid is expected but not provided, a
random one will be generated. This was previously the default
behavior, but is now done only for virtualports inside an
<interface> definition, not for those in <network> or <portgroup>.
* add a REQUIRE_ALL_ATTRIBUTES flag to the parser - if this flag is
set the parser will call the new
virNetDevVPortProfileCheckComplete() functions at the end of the
parser to check for any missing attributes (based on type), and
return failure if anything is missing. This used to be default
behavior. Now it is only used for the virtualport defined inside an
interface's <actual> element (by the time you've figured out the
contents of <actual>, you should have all the necessary data to fill
in the entire virtualport)
* add a REQUIRE_TYPE flag to the parser - if this flag is set, the
parser will return an error if the virtualport has no type
attribute. This also was previously the default behavior, but isn't
needed in the case of the virtualport for a type='network' interface
(i.e. the exact type isn't yet known), or the virtualport of a
portgroup (i.e. the portgroup just has modifiers for the network's
virtualport, which *does* require a type) - in those cases, the
check will be done at domain startup, once the final virtualport is
assembled (this is handled in the next patch).
This function has several calls to increase the buffer indent by 6,
then decrease it again, then increase, then decrease. Additionally,
there were several printfs that had 6 spaces at the beginning of the
line.
virDomainActualNetDefFormat, which is called by virDomainNetDefFormat,
had similar ugliness.
This patch changes both functions to just increase the indent at the
beginning, decrease it at (well, just before*) the end, and remove all
of the occurences of 6/8 spaces at the beginning of lines.
*The indent had to be reset before the end of the function because
virDomainDeviceInfoFormat assumes a 0 indent and is called from many
other places, and I didn't want to do an overhaul of every caller of
that function. A separate patch to switch all of domain_conf.c would
be a useful exercise, but my current goal is unrelated to that, so
I'll leave it for another day.
There was an error: label that simply did "return ret", but ret was
defaulted to -1, and was never used other than setting it manually to
0 just before a non-error return. Aside from this, some of the error
return paths used "goto error" and others used "return ret".
This patch removes ret and the error: label, and makes all error
returns just consistently do "return -1".
virtPortProfile is now used by 4 different types of network devices
(NETWORK, BRIDGE, DIRECT, and HOSTDEV), and it's getting cumbersome to
replicate so much code in 4 different places just because each type
has the virtPortProfile in a slightly different place. This patch puts
a single virtPortProfile in a common place (outside the type-specific
union) in both virDomainNetDef and virDomainActualNetDef, and adjusts
the parse and format code (and the few other places where it is used)
accordingly.
Note that when a <virtualport> element is found, the parse functions
verify that the interface is of a type that supports one, otherwise an
error is generated (CONFIG_UNSUPPORTED in the case of <interface>, and
INTERNAL in the case of <actual>, since the contents of <actual> are
always generated by libvirt itself).
As the consensus in:
https://www.redhat.com/archives/libvir-list/2012-July/msg01692.html,
this patch is to destroy conf/virdomainlist.[ch], folding the
helpers into conf/domain_conf.[ch].
* src/Makefile.am:
- Various indention fixes incidentally
- Add macro DATATYPES_SOURCES (datatypes.[ch])
- Link datatypes.[ch] for libvirt_lxc
* src/conf/domain_conf.c:
- Move all the stuffs from virdomainlist.c into it
- Use virUnrefDomain and virUnrefDomainSnapshot instead of
virDomainFree and virDomainSnapshotFree, which are defined
in libvirt.c, and we don't want to link to it.
- Remove "if" before "free" the object, as virObjectUnref
is in the list "useless_free_options".
* src/conf/domain_conf.h:
- Move all the stuffs from virdomainlist.h into it
- s/LIST_FILTER/LIST_DOMAINS_FILTER/
* src/libxl/libxl_driver.c:
- s/LIST_FILTER/LIST_DOMAINS_FILTER/
- no (include "virdomainlist.h")
* src/libxl/libxl_driver.c: Likewise
* src/lxc/lxc_driver.c: Likewise
* src/openvz/openvz_driver.c: Likewise
* src/parallels/parallels_driver.c: Likewise
* src/qemu/qemu_driver.c: Likewise
* src/test/test_driver.c: Likewise
* src/uml/uml_driver.c: Likewise
* src/vbox/vbox_tmpl.c: Likewise
* src/vmware/vmware_driver.c: Likewise
* tools/virsh-domain-monitor.c: Likewise
* tools/virsh.c: Likewise
Switch virDomainObjPtr to use the virObject APIs for reference
counting. The main change is that virObjectUnref does not return
the reference count, merely a bool indicating whether the object
still has any refs left. Checking the return value is also not
mandatory.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
* src/conf/domain_conf.c:
- Add virDomainControllerFind to find controller device by type
and index.
- Add virDomainControllerRemove to remove the controller device
from maintained controler list.
* src/conf/domain_conf.h:
- Declare the two new helpers.
* src/libvirt_private.syms:
- Expose private symbols for the two new helpers.
* src/qemu/qemu_driver.c:
- Support attach/detach controller device persistently
* src/qemu/qemu_hotplug.c:
- Use the two helpers to simplify the codes.
This patch adds helpers that validate domain's device configuration.
This will be needed later on to verify devices being hot-plugged to
guests. If the guest has no USB bus, then it's not valid to plug a USB
device to that guest.
Libvirt adds a USB controller to the guest even if the user does not
specify any in the XML. This is due to back-compat reasons.
To allow disabling USB for a guest this patch adds a new USB controller
type "none" that disables USB support for the guest.
Parallels Cloud Server is a cloud-ready virtualization
solution that allows users to simultaneously run multiple virtual
machines and containers on the same physical server.
More information can be found here: http://www.parallels.com/products/pcs/
Also beta version of Parallels Cloud Server can be downloaded there.
Signed-off-by: Dmitry Guryanov <dguryanov@parallels.com>
Any time we have a string with no % passed through gettext, a
translator can inject a % to cause a stack overread. When there
is nothing to format, it's easier to ask for a string that cannot
be used as a formatter, by using a trivial "%s" format instead.
In the past, we have used --disable-nls to catch some of the
offenders, but that doesn't get run very often, and many more
uses have crept in. Syntax check to the rescue!
The syntax check can catch uses such as
virReportError(code,
_("split "
"string"));
by using a sed script to fold context lines into one pattern
space before checking for a string without %.
This patch is just mechanical insertion of %s; there are probably
several messages touched by this patch where we would be better
off giving the user more information than a fixed string.
* cfg.mk (sc_prohibit_diagnostic_without_format): New rule.
* src/datatypes.c (virUnrefConnect, virGetDomain)
(virUnrefDomain, virGetNetwork, virUnrefNetwork, virGetInterface)
(virUnrefInterface, virGetStoragePool, virUnrefStoragePool)
(virGetStorageVol, virUnrefStorageVol, virGetNodeDevice)
(virGetSecret, virUnrefSecret, virGetNWFilter, virUnrefNWFilter)
(virGetDomainSnapshot, virUnrefDomainSnapshot): Add %s wrapper.
* src/lxc/lxc_driver.c (lxcDomainSetBlkioParameters)
(lxcDomainGetBlkioParameters): Likewise.
* src/conf/domain_conf.c (virSecurityDeviceLabelDefParseXML)
(virDomainDiskDefParseXML, virDomainGraphicsDefParseXML):
Likewise.
* src/conf/network_conf.c (virNetworkDNSHostsDefParseXML)
(virNetworkDefParseXML): Likewise.
* src/conf/nwfilter_conf.c (virNWFilterIsValidChainName):
Likewise.
* src/conf/nwfilter_params.c (virNWFilterVarValueCreateSimple)
(virNWFilterVarAccessParse): Likewise.
* src/libvirt.c (virDomainSave, virDomainSaveFlags)
(virDomainRestore, virDomainRestoreFlags)
(virDomainSaveImageGetXMLDesc, virDomainSaveImageDefineXML)
(virDomainCoreDump, virDomainGetXMLDesc)
(virDomainMigrateVersion1, virDomainMigrateVersion2)
(virDomainMigrateVersion3, virDomainMigrate, virDomainMigrate2)
(virStreamSendAll, virStreamRecvAll)
(virDomainSnapshotGetXMLDesc): Likewise.
* src/nwfilter/nwfilter_dhcpsnoop.c (virNWFilterSnoopReqLeaseDel)
(virNWFilterDHCPSnoopReq): Likewise.
* src/openvz/openvz_driver.c (openvzUpdateDevice): Likewise.
* src/openvz/openvz_util.c (openvzKBPerPages): Likewise.
* src/qemu/qemu_cgroup.c (qemuSetupCgroup): Likewise.
* src/qemu/qemu_command.c (qemuBuildHubDevStr, qemuBuildChrChardevStr)
(qemuBuildCommandLine): Likewise.
* src/qemu/qemu_driver.c (qemuDomainGetPercpuStats): Likewise.
* src/qemu/qemu_hotplug.c (qemuDomainAttachNetDevice): Likewise.
* src/rpc/virnetsaslcontext.c (virNetSASLSessionGetIdentity):
Likewise.
* src/rpc/virnetsocket.c (virNetSocketNewConnectUNIX)
(virNetSocketSendFD, virNetSocketRecvFD): Likewise.
* src/storage/storage_backend_disk.c
(virStorageBackendDiskBuildPool): Likewise.
* src/storage/storage_backend_fs.c
(virStorageBackendFileSystemProbe)
(virStorageBackendFileSystemBuild): Likewise.
* src/storage/storage_backend_rbd.c
(virStorageBackendRBDOpenRADOSConn): Likewise.
* src/storage/storage_driver.c (storageVolumeResize): Likewise.
* src/test/test_driver.c (testInterfaceChangeBegin)
(testInterfaceChangeCommit, testInterfaceChangeRollback):
Likewise.
* src/vbox/vbox_tmpl.c (vboxListAllDomains): Likewise.
* src/xenxs/xen_sxpr.c (xenFormatSxprDisk, xenFormatSxpr):
Likewise.
* src/xenxs/xen_xm.c (xenXMConfigGetUUID, xenFormatXMDisk)
(xenFormatXM): Likewise.
Per the FSF address could be changed from time to time, and GNU
recommends the following now: (http://www.gnu.org/licenses/gpl-howto.html)
You should have received a copy of the GNU General Public License
along with Foobar. If not, see <http://www.gnu.org/licenses/>.
This patch removes the explicit FSF address, and uses above instead
(of course, with inserting 'Lesser' before 'General').
Except a bunch of files for security driver, all others are changed
automatically, the copyright for securify files are not complete,
that's why to do it manually:
src/security/security_selinux.h
src/security/security_driver.h
src/security/security_selinux.c
src/security/security_apparmor.h
src/security/security_apparmor.c
src/security/security_driver.c
Introduce new members in the virMacAddr 'class'
- virMacAddrSet: set virMacAddr from a virMacAddr
- virMacAddrSetRaw: setting virMacAddr from raw 6 byte MAC address buffer
- virMacAddrGetRaw: writing virMacAddr into raw 6 byte MAC address buffer
- virMacAddrCmp: comparing two virMacAddr
- virMacAddrCmpRaw: comparing a virMacAddr with a raw 6 byte MAC address buffer
then replace raw MAC addresses by replacing
- 'unsigned char *' with virMacAddrPtr
- 'unsigned char ... [VIR_MAC_BUFLEN]' with virMacAddr
and introduce usage of above functions where necessary.
The s390(x) architecture doesn't feature a PCI bus. For the purpose of
supporting virtio devices a virtual bus called virtio-s390 is used.
A new address type VIR_DOMAIN_DEVICE_ADDRESS_TYPE_VIRTIO_S390 is used to
distinguish the virtio devices on s390 from PCI-based virtio devices.
V3 Change: updated QEMU_CAPS_VIRTIO_S390 to fit upstream.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reported by Jason Helfman as a build-breaker on FreeBSD.
* src/conf/domain_conf.c (virDomainFSDefParseXML): Use POSIX
spelling.
* src/openvz/openvz_conf.c (openvzReadFSConf): Likewise.
Currently you can configure LXC to bind a host directory to
a guest directory, but not to bind a guest directory to a
guest directory. While the guest container init could do
this itself, allowing it in the libvirt XML means a stricter
SELinux policy can be written
Introduce a new syntax for filesystems to allow use of a RAM
filesystem
<filesystem type='ram'>
<source usage='10' units='MiB'/>
<target dir='/mnt'/>
</filesystem>
The usage units default to KiB to limit consumption of host memory.
* docs/formatdomain.html.in: Document new syntax
* docs/schemas/domaincommon.rng: Add new attributes
* src/conf/domain_conf.c: Parsing/formatting of RAM filesystems
* src/lxc/lxc_container.c: Mounting of RAM filesystems
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
It turns out that one-bit filtering makes it hard to select the inverse
set, so it is easier to provide filtering groups. For back-compat,
omitting all bits within a group means the group is not used for
filtering, and by definition of a group (each snapshot matches exactly
one bit within the group, and the set of bits in the group covers all
snapshots), selecting all bits also makes the group useless.
Unfortunately, virDomainSnapshotListChildren defined the bit
VIR_DOMAIN_SNAPSHOT_LIST_DESCENDANTS as an expansion rather than a
filter, so we cannot make it part of a filter group, so that bit
(and its counterpart VIR_DOMAIN_SNAPSHOT_LIST_ROOTS for
virDomainSnapshotList) remains a single control bit.
* include/libvirt/libvirt.h.in (virDomainSnapshotListFlags): Add a
couple more flags.
* src/libvirt.c (virDomainSnapshotNum)
(virDomainSnapshotNumChildren): Document them.
(virDomainSnapshotListNames, virDomainSnapshotListChildrenNames):
Likewise, and add thread-safety caveats.
* src/conf/virdomainlist.h (VIR_DOMAIN_SNAPSHOT_FILTERS_*): New
convenience macros.
* src/conf/domain_conf.c (virDomainSnapshotObjListCopyNames)
(virDomainSnapshotObjListCount): Support the new flags.
Until now, it was possible to crash libvirtd when defining domain with
channel device with missing source element.
When creating new virDomainChrDef, target.port is set to -1, but
unfortunately it is an union with addresses that virDomainChrDefFree
tries to free in case the deviceType is channel. Having the port set
to -1 is intended, however the cleanest way to get around the problems
with the crash seems to be renumbering the VIR_DOMAIN_CHR_CHANNEL_
target types to cover new NONE type (with value 0) being the default
(no target type yet).
Another case where we can do the same amount of work with fewer
lines of redundant code, which will make adding new filters easier.
* src/conf/domain_conf.c (virDomainSnapshotNameData): Adjust
struct.
(virDomainSnapshotObjListCount): Delete, now taken care of...
(virDomainSnapshotObjListCopyNames): ...here.
(virDomainSnapshotObjListGetNames): Adjust caller to handle
counting.
(virDomainSnapshotObjListNum): Simplify.
Now that domain listing is a thin wrapper around child listing,
it's easier to have a common entry point. This restores the
hashForEach optimization lost in the previous patch when there
are no snapshots being filtered out of the entire list.
* src/conf/domain_conf.h (virDomainSnapshotObjListGetNames)
(virDomainSnapshotObjListNum): Add parameter.
(virDomainSnapshotObjListGetNamesFrom)
(virDomainSnapshotObjListNumFrom): Delete.
* src/libvirt_private.syms (domain_conf.h): Drop deleted functions.
* src/conf/domain_conf.c (virDomainSnapshotObjListGetNames):
Merge, and (re)add an optimization.
* src/qemu/qemu_driver.c (qemuDomainUndefineFlags)
(qemuDomainSnapshotListNames, qemuDomainSnapshotNum)
(qemuDomainSnapshotListChildrenNames)
(qemuDomainSnapshotNumChildren): Update callers.
* src/qemu/qemu_migration.c (qemuMigrationIsAllowed): Likewise.
* src/conf/virdomainlist.c (virDomainListPopulate): Likewise.
This idea was first suggested by Daniel Veillard here:
https://www.redhat.com/archives/libvir-list/2011-October/msg00353.html
Now that I am about to add more complexity to snapshot listing, it
makes sense to avoid code duplication and special casing for domain
listing (all snapshots) vs. snapshot listing (descendants); adding
a metaroot reduces the number of code lines by having the domain
listing turn into a descendant listing of the metaroot.
Note that this has one minor pessimization - if we are going to list
ALL snapshots without filtering, then virHashForeach is more efficient
than recursing through the child relationships; restoring that minor
optimization will occur in the next patch.
* src/conf/domain_conf.h (_virDomainSnapshotObj)
(_virDomainSnapshotObjList): Repurpose some fields.
(virDomainSnapshotDropParent): Drop unused parameter.
* src/conf/domain_conf.c (virDomainSnapshotObjListGetNames)
(virDomainSnapshotObjListCount): Simplify.
(virDomainSnapshotFindByName, virDomainSnapshotSetRelations)
(virDomainSnapshotDropParent): Match new field semantics.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML)
(qemuDomainSnapshotReparentChildren, qemuDomainSnapshotDelete):
Adjust clients.
and use it for virDomainParseMemory. This allows to parse arbitrary
scaled value, not only memory related values as needed for the
filesystem limits code following later in this series.
The uhci1, uhci2, uhci3 companion controllers for ehci1 must
have a master start port set. Since this value is predictable
we should set it automatically if the app does not supply it
The virDomainDeviceInfoIsSet API was only checking if an
address or alias was set in the struct. Thus if only a
rom bar setting / filename, boot index, or USB master
value was set, they could be accidentally dropped when
formatting XML
No useful error was being reported when an invalid character device
target type is specified in the domainXML. E.g.
...
<console type="pty">
<source path="/dev/pts/2"/>
<target type="kvm" port="0"/>
</console>
...
resulted in
error: Failed to define domain from x.xml
error: An error occurred, but the cause is unknown
With this small patch, the error is more helpful
error: Failed to define domain from x.xml
error: XML error: unknown target type 'kvm' specified for character device
<vcpu> is not an optional node. The value for its 'placement'
actually always defaults to 'static' in the underlying codes.
(Even no 'cpuset' and 'placement' is specified, the domain
process will be pinned to all the available pCPUs).
Though numad will manage the memory allocation of task dynamically,
it wants management application (libvirt) to pre-set the memory
policy according to the advisory nodeset returned from querying numad,
(just like pre-bind CPU nodeset for domain process), and thus the
performance could benefit much more from it.
This patch introduces new XML tag 'placement', value 'auto' indicates
whether to set the memory policy with the advisory nodeset from numad,
and its value defaults to the value of <vcpu> placement, or 'static'
if 'nodeset' is specified. Example of the new XML tag's usage:
<numatune>
<memory placement='auto' mode='interleave'/>
</numatune>
Just like what current "numatune" does, the 'auto' numa memory policy
setting uses libnuma's API too.
If <vcpu> "placement" is "auto", and <numatune> is not specified
explicitly, a default <numatume> will be added with "placement"
set as "auto", and "mode" set as "strict".
The following XML can now fully drive numad:
1) <vcpu> placement is 'auto', no <numatune> is specified.
<vcpu placement='auto'>10</vcpu>
2) <vcpu> placement is 'auto', no 'placement' is specified for
<numatune>.
<vcpu placement='auto'>10</vcpu>
<numatune>
<memory mode='interleave'/>
</numatune>
And it's also able to control the CPU placement and memory policy
independently. e.g.
1) <vcpu> placement is 'auto', and <numatune> placement is 'static'
<vcpu placement='auto'>10</vcpu>
<numatune>
<memory mode='strict' nodeset='0-10,^7'/>
</numatune>
2) <vcpu> placement is 'static', and <numatune> placement is 'auto'
<vcpu placement='static' cpuset='0-24,^12'>10</vcpu>
<numatune>
<memory mode='interleave' placement='auto'/>
</numatume>
A follow up patch will change the XML formatting codes to always output
'placement' for <vcpu>, even it's 'static'.
qemu's behavior in this case is to change the spice server behavior to
require secure connection to any channel not otherwise specified as
being in plaintext mode. libvirt doesn't currently allow requesting this
(via plaintext-channel=<channel name>).
RHBZ: 819499
Signed-off-by: Alon Levy <alevy@redhat.com>
In order to track a block copy job across libvirtd restarts, we
need to save internal XML that tracks the name of the file
holding the mirror. Displaying this name in dumpxml might also
be useful to the user, even if we don't yet have a way to (re-)
start a domain with mirroring enabled up front. This is done
with a new <mirror> sub-element to <disk>, as in:
<disk type='file' device='disk'>
<driver name='qemu' type='raw'/>
<source file='/var/lib/libvirt/images/original.img'/>
<mirror file='/var/lib/libvirt/images/copy.img' format='qcow2' ready='yes'/>
...
</disk>
For now, the element is output-only, in live domains; it is ignored
when defining a domain or hot-plugging a disk (since those contexts
use VIR_DOMAIN_XML_INACTIVE in parsing). The 'ready' attribute appears
when libvirt knows that the job has changed from the initial pulling
phase over to the mirroring phase, although absence of the attribute
is not a sure indicator of the current phase. If we come up with a way
to make qemu start with mirroring enabled, we can relax the xml
restriction, and allow <mirror> (but not attribute 'ready') on input.
Testing active-only XML meant tweaking the testsuite slightly, but it
was worth it.
* docs/schemas/domaincommon.rng (diskspec): Add diskMirror.
* docs/formatdomain.html.in (elementsDisks): Document it.
* src/conf/domain_conf.h (_virDomainDiskDef): New members.
* src/conf/domain_conf.c (virDomainDiskDefFree): Clean them.
(virDomainDiskDefParseXML): Parse them, but only internally.
(virDomainDiskDefFormat): Output them.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: New test file.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-mirror.xml: Likewise.
* tests/qemuxml2xmltest.c (testInfo): Alter members.
(testCompareXMLToXMLHelper): Allow more test control.
(mymain): Run new test.
I almost copied-and-pasted some redundant () into my new code,
and figured a general cleanup prereq patch would be better instead.
No semantic change.
* src/conf/domain_conf.c (virDomainLeaseDefParseXML)
(virDomainDiskDefParseXML, virDomainFSDefParseXML)
(virDomainActualNetDefParseXML, virDomainNetDefParseXML)
(virDomainGraphicsDefParseXML, virDomainVideoAccelDefParseXML)
(virDomainVideoDefParseXML, virDomainHostdevFind)
(virDomainControllerInsertPreAlloced, virDomainDefParseXML)
(virDomainObjParseXML, virDomainCpuSetFormat)
(virDomainCpuSetParse, virDomainDiskDefFormat)
(virDomainActualNetDefFormat, virDomainNetDefFormat)
(virDomainTimerDefFormat, virDomainGraphicsListenDefFormat)
(virDomainDefFormatInternal, virDomainNetGetActualHostdev)
(virDomainNetGetActualBandwidth, virDomainGraphicsGetListen):
Reduce extra ().
https://bugzilla.redhat.com/show_bug.cgi?id=617711 reported that
even with my recent patched to allow <memory unit='G'>1</memory>,
people can still get away with trying <memory>1G</memory> and
silently get <memory unit='KiB'>1</memory> instead. While
virt-xml-validate catches the error, our C parser did not.
Not to mention that it's always fun to fix bugs while reducing
lines of code. :)
* src/conf/domain_conf.c (virDomainParseMemory): Check for parse error.
(virDomainDefParseXML): Avoid strtoll.
* src/conf/storage_conf.c (virStorageDefParsePerms): Likewise.
* src/util/xml.c (virXPathLongBase, virXPathULongBase)
(virXPathULongLong, virXPathLongLong): Likewise.
The below patch fixes the following memory leak.
==20624== 24 bytes in 2 blocks are definitely lost in loss record 532 of 1,867
==20624== at 0x4A05E46: malloc (vg_replace_malloc.c:195)
==20624== by 0x38EC27FC01: strdup (strdup.c:43)
==20624== by 0x4EB6BA3: virDomainChrSourceDefCopy (domain_conf.c:1122)
==20624== by 0x495D76: qemuProcessFindCharDevicePTYs (qemu_process.c:1497)
==20624== by 0x498321: qemuProcessWaitForMonitor (qemu_process.c:1258)
==20624== by 0x49B5F9: qemuProcessStart (qemu_process.c:3652)
==20624== by 0x468B5C: qemuDomainObjStart (qemu_driver.c:4753)
==20624== by 0x469171: qemuDomainStartWithFlags (qemu_driver.c:4810)
==20624== by 0x4F21735: virDomainCreate (libvirt.c:8153)
==20624== by 0x4302BF: remoteDispatchDomainCreateHelper (remote_dispatch.h:852)
==20624== by 0x4F72C14: virNetServerProgramDispatch (virnetserverprogram.c:416)
==20624== by 0x4F6D690: virNetServerHandleJob (virnetserver.c:164)
==20624== by 0x4E8F43D: virThreadPoolWorker (threadpool.c:144)
==20624== by 0x4E8EAB5: virThreadHelper (threads-pthread.c:161)
==20624== by 0x38EC606CCA: start_thread (pthread_create.c:301)
==20624== by 0x38EC2E0C2C: clone (clone.S:115)
So that a domain xml which doesn't have "placement" specified, but
"cpuset" is specified, could be parsed. And in this case, the
"placement" mode will be set as "static".
As explained in previous patch, numad will balance the affinity
dynamically, so reflecting the cpuset from numad at the first
time doesn't make much case, and may just could cause confusion.
Although it should be harmless to do:
disk = disk = def->disks[i]
some not-so-wise compilers may fool around.
Besides, such assignment is useless here.
