Some kernel versions expose broken NUMA topology for some machines.
This causes the LXC/UML drivers to fail to start. QEMU driver was
already fixed for this problem
* src/lxc_conf.c: Log and ignore failure to populate NUMA info
* src/uml_conf.c: Log and ignore failure to populate NUMA info
* src/capabilities.c: Reset nnumaCell to 0 after freeing
A couple of minor fixes to phyp escape_specialcharacters. Make it
a static function (since it's only used in phyp/phyp_driver.c), and
make it take a dstlen parameter. This paves the way for removing
strncpy in the future.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Minor fix to openvzGetVPSUUID to make it take a length parameter.
This ensures that it doesn't make assumptions about the length
of the UUID buffer, and paves the way for removal of strncpy in
the future.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
As of qemu 0.10.6, qemu now honors the -S flag on incoming migration.
That means that when the migration completes, we have to issue a
'cont' command to get the VM running again. We do it unconditionally
since it won't hurt on older qemu.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Re-factor virDomainMigrate to split out the version 1 and version 2
protocols into their own functions. In reality, the two versions share
very little in common, so forcing them together in the same function was
just confusing. This will also make adding tunnelled migration easier.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
When doing a restore, we were forgetting to update the state file
for the VM. That means that if you do a save/restore, then shut
down libvirtd, then start it back up, you'll see the state of the
guest as "paused", even though it is really running. We were
just forgetting a "virDomainSaveStatus" call in the restor path.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
If the ipv6 kernel module is not loaded, then we get this when starting
a virtual network:
libvir: Network Config error :
cannot enable /proc/sys/net/ipv6/conf/virbr0/disable_ipv6:
No such file or directory
If disable_ipv6 is not present, we should just merrily continue on our
way.
* src/network_driver.c: make networkDisableIPV6() not fail if the kernel
has no ipv6 support
Allow qemu user to open kernel/initrds in this dir, but still prevent
others from listing it.
* libvirt.spec.in: set /var/lib/libvirt/boot perms to 0711
If we're running qemu unprivileged, we need to chown any supplied kernel
or initrd before spawning it.
* src/qemu_driver.c: rename qemuDomainSetDiskOwnership() to
qemuDomainSetFileOwnership(), pass it a path string instead of a disk
definition and use it for chowning the kernel/initrd in
qemuDomainSetAllDeviceOwnership()
While trying to remove uses of unsafe strncpy in the tree, I came
across a couple of usages in the ESX driver. To my eyes, the snprintf
replacements do the same thing in less code, and are also safer.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Tested-by: Mattias Bolte <matthias.bolte@googlemail.com>
* src/logging.c src/logging.h src/libvirt_private.syms:
define new functions virLogSetFromEnv and virLogParseDefaultPriority
* qemud/qemud.c src/libvirt.c tests/eventtest.c: cleanup to use the
unified functions
* qemud/qemud.c src/logging.[ch]: Similar as for general libvirt, don't
convert high priority levels to debug level. Ignore LIBVIRT_LOG_FILTERS
and LIBVIRT_LOG_OUTPUTS when they're set to the empty string, otherwise
they can override a valid setting from the config file. Send all
settings through the parser functions for validation, so that the
existence of a bad setting doesn't nullify a good setting that should
have applied -- particularly the default output. Keep the order of
precedence consistent for all variables between the environment and
the config file. Warn when an invalid log level, filter, or output
is ignored.
* src/libvirt_private.syms: export internally a few convenience functions
* src/libvirt.c src/logging.c: Don't convert high priority levels to the
debug level. Don't parse LIBVIRT_LOG_FILTERS and LIBVIRT_LOG_OUTPUTS
when they're set to the empty string. Warn when the user specifies an
invalid value (empty string remains a noop).
* po/POTFILES.in: src/logging.c now include translatable strings
* src/xm_internal.c: in case of multiple connections to the xen driver
and some clients were not using domain events, the whole /etc/xen
monitoring would break leading to disapearing domains.
* src/esx/esx_driver.c src/esx/esx_vi.[ch] src/esx/esx_vmx.[ch]:
adds version checking for GSX 2.0, allows to pass a specific port
for the connection and also add a new specific gsx scheme for
easier connections to GSX hosts
Fix up qemudDomainMigratePrepare2 to use virGetHostname instead of
gethostname. Besides the fact that virGetHostname is far more clever,
there was a latent bug in the handling that could cause a buffer overflow
on a very long hostname.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
