Turns out, there are couple of bugs that prevent this feature
from being operational. Given how close to the release we are
disable the feature temporarily. Hopefully, it can be enabled
back after all the bugs are fixed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
Let's ignore the checking of interface type when we call the function
qemuARPGetInterfaces to get IP from host's arp table.
Signed-off-by: Lin Ma <lma@suse.com>
Reviewed-by: Chen Hanxiao <chenhanxiao@gmail.com>
The only place where VIR_DOMAIN_EVENT_RESUMED should be generated is the
RESUME event handler to make sure we don't generate duplicate events or
state changes. In the worse case the duplicity can revert or cover
changes done by other event handlers.
For example, after QEMU sent RESUME, BLOCK_IO_ERROR, and STOP events
we could happily mark the domain as running and report
VIR_DOMAIN_EVENT_RESUMED to registered clients.
https://bugzilla.redhat.com/show_bug.cgi?id=1612943
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Thanks to the previous commit the RESUME event handler knows what reason
should be used when changing the domain state to VIR_DOMAIN_RUNNING, but
the emitted VIR_DOMAIN_EVENT_RESUMED event still uses a generic
VIR_DOMAIN_EVENT_RESUMED_UNPAUSED detail. Luckily, the event detail can
be easily deduced from the running reason, which saves us from having to
pass one more value to the handler.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Whenever we get the RESUME event from QEMU, we change the state of the
affected domain to VIR_DOMAIN_RUNNING with VIR_DOMAIN_RUNNING_UNPAUSED
reason. This is fine if the domain is resumed unexpectedly, but when we
sent "cont" to QEMU we usually have a better reason for the state
change. The better reason is used in qemuProcessStartCPUs which also
sets the domain state to running if qemuMonitorStartCPUs reports
success. Thus we may end up with two state updates in a row, but the
final reason is correct.
This patch is a preparation for dropping the state change done in
qemuMonitorStartCPUs for which we need to pass the actual running reason
to the RESUME event handler and use it there instead of
VIR_DOMAIN_RUNNING_UNPAUSED.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
This patch replaces some rather generic VIR_DOMAIN_RUNNING_UNPAUSED
reasons when changing domain state to running with more specific ones.
All of them are done when libvirtd reconnects to an existing domain
after being restarted and sees an unfinished migration or save.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
VIR_DOMAIN_EVENT_RESUMED_FROM_SNAPSHOT was defined but not used anywhere
in our event generation code. This fixes qemuDomainRevertToSnapshot to
properly report why the domain was resumed.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Once we introduce cgroup v2 support we need to handle processes and
threads differently.
Reviewed-by: Fabiano Fidêncio <fidencio@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
In cgroup v2 we need to handle processes and threads differently,
following patch will introduce virCgroupAddThread.
Reviewed-by: Fabiano Fidêncio <fidencio@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
In a following case:
virsh start $domain
service libvirtd stop
<shutdown> the guest from within the $domain
service libvirtd start
Notice that PCI devices which have been assigned to the $domain will
still be bound to stub drivers instead rebound to host drivers.
In that case the call stack is like below:
libvirtd start
qemuProcessReconnect
qemuProcessStop (because $domain was shutdown without
libvirtd event to process that)
qemuHostdevReAttachDomainDevices
qemuHostdevReAttachPCIDevices
virHostdevReAttachPCIDevices
However, because qemuHostdevUpdateActiveDomainDevices was called
after the qemuConnectMonitor, the setup of the tracking of each
host device in the $domain on either the activePCIHostdevs list
or inactivePCIHostdev list will not occur in an orderly manner.
Therefore, virHostdevReAttachPCIDevices just neglects these host PCI
devices which are bound to stub drivers and doesn't rebind them to
host drivers.
This patch fixs that by moving qemuHostdevUpdateActiveDomainDevices before
qemuConnectMonitor during libvirtd reconnection processing.
Signed-off-by: Wu Zongyong <cordius.wu@huawei.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Use the new qemuDomainRemoveInactiveJobLocked to remove the
@obj during the virDomainObjListForEach call which holds a
lock on the domain object list.
Signed-off-by: Wang Yechao <wang.yechao255@zte.com.cn>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Create a qemuDomainRemoveInactiveJobLocked which copies
qemuDomainRemoveInactiveJob except of course calling
another new helper qemuDomainRemoveInactiveLocked.
The qemuDomainRemoveInactiveLocked is a copy of
qemuDomainRemoveInactive except that instead of calling
virDomainObjListRemove it calls virDomainObjListRemoveLocked.
Signed-off-by: Wang Yechao <wang.yechao255@zte.com.cn>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Introduce qemuDomainRemoveInactiveJobCommon to handle what will
be the common parts of the code with a new function that will
be used to call virDomainObjListRemoveLocked instead of the
unlocked variant.
Signed-off-by: Wang Yechao <wang.yechao255@zte.com.cn>
Reviewed-by: John Ferlan <jferlan@redhat.com>
It was already available in 1.5.0, so we can assume it's
present and avoid checking for it at runtime.
This commit is best viewed with 'git show -w'.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
We already prefer them in capabilities, and domcapabilities
should be consistent with that.
This commit is best viewed with 'git show -w'.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
The new implementation contains less duplicated code and
is easier to extend.
This commit is best viewed with 'git show -w'.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Now that we have reduced the number of sensible options down
to either the native QEMU binary or RHEL's qemu-kvm, we can
make virQEMUCapsInitGuest() a bit simpler.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Both Fedora's qemu-kvm and Debian's/Ubuntu's kvm are nothing
more than paper-thin wrappers around the native QEMU binary,
so we gain nothing by looking for them.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
We're only ever passing a single binary when calling this
function, so we can remove all code dealing with the
possibility of a second binary being specified.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
When the guest is native, we are currently looking at
potential KVM binaries regardless of whether or not we have
already located a QEMU binary suitable to run the guest.
This made sense back when KVM support was not part of QEMU
proper, but these days the KVM binaries are in most cases
just trivial wrapper scripts around the native QEMU binary
so it doesn't make sense to poke at them unless they're
the only binaries on the system, such as when running on
RHEL.
This will allow us to simplify both virQEMUCapsInitGuest()
and virQEMUCapsInitGuestFromBinary().
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
When running an armv7l guest on an aarch64 hosts, the
qemu-system-aarch64 binary should be our first choice instead
of qemu-system-arm since the former can take advantage of KVM
acceleration.
Move the special case to virQEMUCapsFindBinaryForArch() so
that it's handled along with all other cases rather than on
its own later on.
Doing so will also make further refactoring easier.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
virCapabilitiesAddGuestDomain() takes an optional binary
name: this is intended for cases where a certain domain
type can't use the default one registered for the guest
architecture, but has to use a special binary instead.
The current code, however, will pass 'binary' again when
'kvmbin' is not defined, which is unnecessary as 'binary'
has been registered as default earlier, and will result
in capabilities output such as
<emulator>/usr/bin/qemu-system-x86_64</emulator>
<domain type='qemu'/>
<domain type='kvm'>
<emulator>/usr/bin/qemu-system-x86_64</emulator>
</domain>
with the second <emulator> element providing no additional
information.
Change it so that, when 'kvmbin' is not defined, NULL is
passed and so the default emulator will be used instead.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
The function performing the checks, rather than its callers,
should contain comments explaining the rationale behind said
checks.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1630164
Since 2a13a0a103 we are querying the vhostuser's interface name
when building qemu command line. However, we forgot to do so on
hotplug.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
There seems to be no need to add the ignore_value wrapper or
caste with (void) to the unlink() calls, so let's just remove
them. I assume at one point in time Coverity complained. So,
let's just be consistent - those that care to check the return
status can and those that don't can just have the naked unlink.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1607202
It's essentially stated in the nwfilterBindingDelete that we
will allow the admin to shoot themselves in the foot by deleting
the nwfilter binding which then allows them to undefine the
nwfilter that is in use for the running guest...
However, by allowing this we cause a problem for libvirtd
restart reconnect processing which would then try to recreate
the missing binding attempting to use the deleted filter
resulting in an error and thus shutting the guest down.
So rather than keep adding virDomainConfNWFilterInstantiate
flags to "ignore" specific error conditions, modify the logic
to ignore, but VIR_WARN errors other than ignoreExists. This
will at least allow the guest to not shutdown for only nwfilter
binding errors that we can now perhaps recover from since we
have the binding create/delete capability.
Signed-off-by: John Ferlan <jferlan@redhat.com>
ACKed-by: Michal Privoznik <mprivozn@redhat.com>
All of the ones being removed are pulled in by internal.h. The only
exception is sanlock which expects the application to include <stdint.h>
before sanlock's headers, because sanlock prototypes use fixed width
int, but they don't include stdint.h themselves, so we have to leave
that one in place.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Acked-by: Michal Privoznik <mprivozn@redhat.com>
It doesn't really make sense for us to have stdlib.h and string.h but
not stdio.h in the internal.h header.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Acked-by: Michal Privoznik <mprivozn@redhat.com>
When restoring a domain from a compressed image, we launch an
intermediate process for decompressing the saved data. If QEMU fails to
load the data for some reason, we force close the stdin/stdout file
descriptors of the intermediate process and wait for it to die. However,
virCommandWait can report various errors which would overwrite the real
error from QEMU. Thus instead of getting something useful:
internal error: process exited while connecting to monitor:
2018-09-17T15:17:29.998910Z qemu-system-x86_64: can't apply global
Skylake-Client-x86_64-cpu.osxsave=off: Property '.osxsave' not found
we could get an irrelevant error message:
internal error: Child process (lzop -dc --ignore-warn) unexpected
fatal signal 13
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Now that we know what metadata lock manager user wishes to use we
can load it when initializing security driver. This is achieved
by adding new argument to virSecurityManagerNewDriver() and
subsequently to all functions that end up calling it.
The cfg.mk change is needed in order to allow lock_manager.h
inclusion in security driver without 'syntax-check' complaining.
This is safe thing to do as locking APIs will always exist (it's
only backend implementation that changes). However, instead of
allowing the include for all other drivers (like cpu, network,
and so on) allow it only for security driver. This will still
trigger the error if including from other drivers.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
This config option allows users to set and enable lock manager
for domain metadata. The lock manager is going to be used by
security drivers to serialize each other when changing a file
ownership or changing the SELinux label. The only supported lock
manager is 'lockd' for now.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
The file being present doesn't necessarily mean anything these
days, as it's created independently of whether the kvm module
has been loaded[1]; moreover, we're already gathering all the
information we need through QMP, so poking the filesystem at
all is entirely unnecessary.
[1] https://github.com/systemd/systemd/commit/d35d6249d5a7ed3228
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
This capability is documented as having one meaning (whether
KVM is enabled by default) but is actually assigned two other
meanings over its life: whether the query-kvm QMP command is
available at first, and later on whether KVM is usable / was
used during probing.
Since the query-kvm QMP command was available in 1.5.0, we
can avoid probing for it; additionally, we can simplify the
logic by setting the flag when it applies instead of initially
setting it and then clearing it when it doesn't.
The flag's description is also updated to reflect reality.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
A side effect of recent changes is that we would always try
to regenerate the capabilities cache for non-native QEMU
binaries based on /dev/kvm availability, which is of course
complete nonsense. Make sure that doesn't happen.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
It was already available in 1.5.0.
Moreover, we're not even formatting it on the QEMU command
line, ever: we just use it as part of some logic that decides
whether KVM support should be advertised, and as it turns out
that logic is actually buggy and dropping this capability
fixes it.
https://bugzilla.redhat.com/show_bug.cgi?id=1628469
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
Now that committing transactions using pid == -1 means that we're
not fork()-ing to run the transaction in a specific namespace, we
can utilize the transaction processing semantics in order to
start, run a or multiple commands, and then commit the
transaction without being concerned with other interactions or
transactions interrupting the processing. This will eventually
allow us to have a single place where all the paths can be
locked, followed by relabeling and unlocking again.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
In the future, the transactions are not going to be optional and
they will be run regardless of domain using namespace to collect
list of paths to be relabeled.
To make sure there won't be an API that goes behind transaction
code back update the comment that serves as decision manual
whether an API must be fully implemented or plain #define is
sufficient.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Even though the current use of the functions does not require full
implementation with transactions (none of the callers passes a path
somewhere under /dev), it doesn't hurt either. Moreover, in
future patches the paradigm is going to shift so that any API
that touches a file is required to use transactions.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Even though the current use of the function does not require full
implementation with transactions (none of the callers pass a path
somewhere under /dev), it doesn't hurt either. Moreover, in
future patches the paradigm is going to shift so that any API
that touches a file is required to use transactions.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
It is not a problem at all if the `tss` user/group does not exist, the code
fallbacks to the `root` user/group. However we report a warning for no reason
on every start-up. Fix this by checking if the user/group actually exists.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
After removing the host CPU model re-computation,
this function is no longer necessary.
This reverts commits:
commit d0498881a0
virQEMUCapsFreeHostCPUModel: Don't always free host cpuData
commit 5276ec712a
testUpdateQEMUCaps: Don't leak host cpuData
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Commit 82327038 moved a couple of checks out of the XML parser
into the domain validation; however, those checks seem to be more
useful as hypervisor specific checks rather than the more general
domain conf checks (nothing in the docs indicate a specific error).
Fortunately only QEMU was processing the memoryBacking, thus
add the changes to qemuDomainDefValidateMemory and change the
code a bit to make usage of the similar deref to def->mem and
the mem->nhugepages filter.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
We require QEMU 1.5.0 these days, so checking for versions
older than that is pointless.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The capability was introduced in QEMU 1.5.0, which is our
minimum supported QEMU version these days.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The capability was introduced in QEMU 1.3.1 and we require
QEMU 1.5.0 these days.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
