Adds a new interface type using UDP sockets, this seems only applicable
to QEMU but have edited tree-wide to support the new interface type.
The interface type required the addition of a "localaddr" (local
address), this then maps into the following xml and qemu call.
<interface type='udp'>
<mac address='52:54:00:5c:67:56'/>
<source address='127.0.0.1' port='11112'>
<local address='127.0.0.1' port='22222'/>
</source>
<model type='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</interface>
QEMU call:
-net socket,udp=127.0.0.1:11112,localaddr=127.0.0.1:22222
Notice the xml "local" entry becomes the "localaddr" for the qemu call.
reference:
http://lists.gnu.org/archive/html/qemu-devel/2011-11/msg00629.html
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This is backed by the qemu device ioh3420.
chassis and port from the <target> subelement are used to store/set the
respective qemu device options for the ioh3420. Currently, chassis is
set to be the index of the controller, and port is set to
"(slot << 3) + function" (per suggestion from Alex Williamson).
If a pci address had a function number out of range, the error message
would be:
Insufficient specification for PCI address
which is logged by virDevicePCIAddressParseXML() after
virDevicePCIAddressIsValid returns a failure.
This patch enhances virDevicePCIAddressIsValid() to optionally report
the error itself (since it is the place that decides which part of the
address is "invalid"), and uses that feature when calling from
virDevicePCIAddressParseXML(), so that the error will be more useful,
e.g.:
Invalid PCI address function=0x8, must be <= 7
Previously, virDevicePCIAddressIsValid didn't check for the
theoretical limits of domain or bus, only for slot or function. While
adding log messages, we also correct that ommission. (The RNG for PCI
addresses already enforces this limit, which by the way means that we
can't add any negative tests for this - as far as I know our
domainschematest has no provisions for passing XML that is supposed to
fail).
Note that virDevicePCIAddressIsValid() can only check against the
absolute maximum attribute values for *any* possible PCI controller,
not for the actual maximums of the specific controller that this
device is attaching to; fortunately there is later more specific
validation for guest-side PCI addresses when building the set of
assigned PCI addresses. For host-side PCI addresses (e.g. for
<hostdev> and for network device pools), we rely on the error that
will be logged when it is found that the device doesn't actually
exist.
This resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=1004596
PowerPC pseries based VMs do not support a floppy disk controller.
This prohibits libvirt from creating qemu command with floppy device.
Signed-off-by: Kothapally Madhu Pavan <kmp@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1180486
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This reverts commit 7b401c3bda.
Until libvirt is able to differentiate whether heads='1' is just a
leftover from previous libvirt or whether that's added by user on
purpose and also whether the domain was started with the support for
qxl's max_outputs, we cannot incorporate this patch into the tree
due to compatibility reasons.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Allows to specify maximum number of head to QXL driver.
Actually can be a compatiblity problem as heads in the XML configuration
was set by default to '1'.
Signed-off-by: Frediano Ziglio <fziglio@redhat.com>
This patch adds a test for the qemu command line generation.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Jason J. Herne <jjherne@us.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1142631
Commit id 'e0e290552' added a check to determine if the same bus
had the same target value. It seems that's not quite good enough
as the check should check the target name value regardless of bus type.
Also added a DO_TEST_DIFFERENT to exhibit the issue
If user passes an invalid address for shared memory device to qemu,
neither libvirt nor qemu will report an error, but qemu will auto assign
a pci address to the shared memory device.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Since QEMU commit ea96bc6 [1]:
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
the floppy controller is no longer implicit.
Specify it explicitly on the command line if the machine type version
is 2.4 or later.
Note that libvirt's floppy drives do not result in QEMU implying the
controller, because libvirt uses if=none instead of if=floppy.
https://bugzilla.redhat.com/show_bug.cgi?id=1227880
[1] http://git.qemu.org/?p=qemu.git;a=commitdiff;h=ea96bc6
The code which generates paths for UNIX socket blindly used target name
without checking if it was set. Thus for the following device XML
<channel type='unix'>
<source mode='bind'/>
<target type='virtio'/>
</channel>
we would generate "/var/lib/libvirt/qemu/channel/target/NAME.(null)"
path which works but is not really correct. Let's not use the
".target_name" suffix at all if target name is not set.
https://bugzilla.redhat.com/show_bug.cgi?id=1226854
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1201143
The formatdomain.html description for <disk> device 'lun' indicates that
it must be either a type 'block' or type 'network' with protocol 'iscsi';
however, we did not make that check until domain startup.
This caused issues for virt-manager which had an unexpected failure at
run time rather config time.
This patch adds a check in post part disk device checking for the specific
and supported lun types as well as adjusting the test failure to be for
parse config rather than run time.
Make sure we only assign the default spicevmc channel name to spicevmc
virtio channels. Caused by commits 3269ee65 and 1133ee2b, which moved
the assignment from XML parsing code to QEMU but failed to keep the
logic.
https://bugzilla.redhat.com/show_bug.cgi?id=1179680
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
So far the argument has not much meaning and was practically ignored.
This is not good since when doing memory hotplug, the size of desired
hugepage backing is passed in that argument. Taking closer look at the
tests I'm fixing reveals the bug. For instance, while the following is
in the test:
<memory model='dimm'>
<source>
<nodemask>1-3</nodemask>
<pagesize unit='KiB'>4096</pagesize>
</source>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
<address type='dimm' slot='0' base='0x100000000'/>
</memory>
the generated commandline corresponding to this XML was:
-object memory-backend-ram,id=memdimm0,size=536870912,\
host-nodes=1-3,policy=bind
Have you noticed? Yes, memory-backend-ram! Nothing can be further away
from the right answer. The hugepage backing is requested in the XML
and we happily ignore it. This is just not right. It's
memory-backend-file which should have been used:
-object memory-backend-file,id=memdimm0,prealloc=yes,\
mem-path=/dev/hugepages4M/libvirt/qemu,size=536870912,\
host-nodes=1-3,policy=bind
The problem is, that @pagesize passed to qemuBuildMemoryBackendStr
(where this part of commandline is built) was ignored. The hugepage to
back memory was searched only and only by NUMA nodes pinning. This
works only for regular guest NUMA nodes.
Then, I'm changing the hugepages size in the test XMLs too. This is
simply because in the test suite we create dummy mount points just for
2M and 1G hugepages. And in the test 4M was requested. I'm sticking to
2M, but 1G should just work too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1196644
This function constructs the backend (host facing) part of the
memory device. At the beginning, the configured hugepages are
searched to find the best match for given guest NUMA node.
Configured hugepages can have a @nodeset attribute to specify on
which guest NUMA nodes should be the hugepages backing used.
There is, however, one 'corner case'. Users may just tell 'use
hugepages to back all the nodes'. In other words:
<memoryBacking>
<hugepages/>
</memoryBacking>
<cpu>
<numa>
<cell id='0' cpus='0-1' memory='1024000' unit='KiB'/>
</numa>
</cpu>
Our code fails in this case. Well, since there's no @nodeset (nor
any <page/> child element to <hugepages/>) we fail to lookup the
default hugepage size to use.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The privileged flag will not change while the configuration might
change. Make the 'privileged' flag member of the driver again and mark
it immutable. Should that ever change add an accessor that will group
reads of the state.
This patch adds the support of queues attribute of the driver element
for vhost-user interface type. Example:
<interface type='vhostuser'>
<mac address='52:54:00:ee:96:6d'/>
<source type='unix' path='/tmp/vhost2.sock' mode='client'/>
<model type='virtio'/>
<driver queues='4'/>
</interface>
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1207692
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
qemu 2.3.0 added the -cpu host,aarch64=off option, which allows using
qemu-system-aarch64 KVM to run armv7l VMs.
Add a capabilities check for it, wire it up in qemu_command, and test
the command line generation.
The guest firmware provides the same functionality as the pvpanic
device, and the relevant element should always be present in the
domain XML to reflect this fact, so add it after parsing the
definition if it wasn't there already.
The guest firmware provides the same functionality as the pvpanic
device, which is not available in QEMU on pSeries, so the domain
XML should be allowed to contain the <panic> element.
On the other hand, unlike the pvpanic device, the guest firmware
can't be configured, so report an error if an address has been
provided in the XML.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182388
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Implementation is pretty straight-forward. Of course, not all qemus
out there supports the device, so new capability is introduced and
checked prior each use of the device.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Test the support for enabling/disabling CPACF protected key management
operations for a guest.
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Back in 2013, commit 877bc089 added in some tests that made sure no
error was generated on a domain definition that had an automatically
added usb controller if that domain didn't have a PCI bus to attach
the usb controller to. This was done because, at that time, libvirt
was automatically adding a usb controller to *any* domain definition
that didn't have one. Along with permitting the controller, two
s390-specific tests were added to ensure this behavior was maintained
- one with <controller type='usb' model='none'/> and another (called
"s390-piix-controllers") that had both usb and ide controllers, but
nothing attached to them.
Then in February of this year, commit 09ab9dcc eliminated the annoying
auto-adding of a usb device for s390 and s390x machines, stating:
"Since s390 does not support usb the default creation of a usb
controller for a domain should not occur."
Although, as verified here, the s390 doesn't support usb, and usb
controllers aren't currently added to s390 domain definitions
automatically, there are likely still some domain definitions in the
wild that have a usb controller (which was added *by libvirt*, not by
the user), so we will keep the tests verifying that behavior for
now. But this patch changes the names of the tests to reflect that
they don't actually contain a valid s390 config; this way future
developers won't propagate the incorrect idea that an s390 virtual
machine can have a USB (or IDE) bus.
In the case of the IDE controller, though, libvirt has never
automatically added an IDE controller unless a user added an IDE disk
(which itself would have caused an error), and we specifically *do*
want to begin generating an error when someone tries to add an IDE
controller to a domain that can't support one. For that reason, while
renaming the sz390-piix-controllers patch, this patch removes the
<controller type='ide'...> from it (otherwise the upcoming patch would
break make check)
My commit 747761a79 (v1.2.15 only) dropped this bit of logic when filling
in a default arch in the XML:
- /* First try to find one matching host arch */
- for (i = 0; i < caps->nguests; i++) {
- if (caps->guests[i]->ostype == ostype) {
- for (j = 0; j < caps->guests[i]->arch.ndomains; j++) {
- if (caps->guests[i]->arch.domains[j]->type == domain &&
- caps->guests[i]->arch.id == caps->host.arch)
- return caps->guests[i]->arch.id;
- }
- }
- }
That attempt to match host.arch is important, otherwise we end up
defaulting to i686 on x86_64 host for KVM, which is not intended.
Duplicate it in the centralized CapsLookup function.
Additionally add some testcases that would have caught this.
https://bugzilla.redhat.com/show_bug.cgi?id=1219191
My commit 7b9de914 added some aarch64 CPU test cases. I wanted to test
two different code paths but inadvertently added two of the same test
cases.
The second code path (using <cpu><model>host</model</cpu>) isn't easily
exercised via the qemu tests anyways, I'll need to look elsewhere.
Regardless, remove the redundant tests for now
The only version that's supported in QEMU is version 2, currently.
Fortunately, it is enabled by aarch64 automatically, so there's
nothing for us that needs to be put onto command line.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Add 'thread_id' to the virDomainIOThreadIDDef as a means to store the
'thread_id' as returned from the live qemu monitor data.
Remove the iothreadpids list from _qemuDomainObjPrivate and replace with
the new iothreadids 'thread_id' element.
Rather than use the default numbering scheme of 1..number of iothreads
defined for the domain, use the iothreadid's list for the iothread_id
Since iothreadids list keeps track of the iothread_id's, these are
now used in place of the many places where a for loop would "know"
that the ID was "+ 1" from the array element.
The new tests ensure usage of the <iothreadid> values for an exact number
of iothreads and the usage of a smaller number of <iothreadid> values than
iothreads that exist (and usage of the default numbering scheme).
- Make sure aarch64 host-passthrough works correctly
- Make sure libvirt doesn't choke on cpu model=host, which is what
virt-install/virt-manager were incorrectly specifying up until recently.
This needs to specified in way too many places for a simple validation
check. The ostype/arch/virttype validation checks later in
DomainDefParseXML should catch most of the cases that this was covering.
According to docs, using 'lun' as a value for device attribute is only valid
with disk types 'block' and 'network'. However current RNG schema also allows
a combination type='file' device='lun' which results in a successfull
xml validation, but fails at qemuBuildCommandLine.
Besides fixing the RNG schema, this patch also adds a qemuxml2argvtest
for this case.
https://bugzilla.redhat.com/show_bug.cgi?id=1210669
On IRC, Hydrar pointed a problem where 'virsh edit' failed on
his domain created through an ISCSI pool managed by virt-manager,
all because the XML included a block device with colons in the
name.
* docs/schemas/basictypes.rng (absFilePath): Add colon as safe.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.xml: New file.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.args: Likewise.
* tests/qemuxml2argvtest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Starting a qemu VM with a memory module that has the base address
specified results in the following error:
error: internal error: early end of file from monitor: possible problem:
2015-03-26T03:45:52.338891Z qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,
id=dimm0,slot=0,base=4294967296: Property '.base' not found
The correct property name for the base address is 'addr'.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
QEMU 2.3 adds these new models to cover Haswell and Broadwell CPUs with
updated microcode. Luckily, they also reverted former the machine type
specific changes to existing models. And since these changes were never
released, we don't need to hack around them in libvirt.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add support to start qemu instance with 'pc-dimm' device. Thanks to the
refactors we are able to reuse the existing function to determine the
parameters.
To enable memory hotplug the maximum memory size and slot count need to
be specified. As qemu supports now other units than mebibytes when
specifying memory, use the new interface in this case.
