This commit is safe precisely because there has been no release
for any of the enum values being deleted (they were added post-0.9.1).
After the 0.9.2 release, we can then take advantage of
virDomainModificationImpact in more places.
* include/libvirt/libvirt.h.in (virDomainModificationImpact): New
enum.
(virDomainSchedParameterFlags, virMemoryParamFlags): Delete, since
these were never released, and the new enum works fine here.
* src/libvirt.c (virDomainGetMemoryParameters)
(virDomainSetMemoryParameters)
(virDomainGetSchedulerParametersFlags)
(virDomainSetSchedulerParametersFlags): Update documentation.
* src/qemu/qemu_driver.c (qemuDomainSetMemoryParameters)
(qemuDomainGetMemoryParameters, qemuSetSchedulerParametersFlags)
(qemuSetSchedulerParameters, qemuGetSchedulerParametersFlags)
(qemuGetSchedulerParameters): Adjust clients.
* tools/virsh.c (cmdSchedinfo, cmdMemtune): Likewise.
Based on ideas by Daniel Veillard and Hu Tao.
Detected by Coverity. This leaked a cpumap on every iteration
of the loop. Leak introduced in commit 1cc4d02 (v0.9.0).
* src/qemu/qemu_process.c (qemuProcessSetVcpuAffinites): Plug
leak, and hoist allocation outside loop.
In v3 migration, once migration is completed, the VM needs
to be left in a paused state until after Finish3 has been
executed on the target. Only then will the VM be killed
off. When using non-JSON QEMU monitor though, we don't
receive any 'STOP' event from QEMU, so we need to manually
set our state offline & thus release lock manager leases.
It doesn't hurt to run this on the JSON case too, just in
case the event gets lost somehow
* src/qemu/qemu_migration.c: Explicitly set VM state to
paused when migration completes
The change 18c2a59206 caused
some regressions in behaviour of virDomainBlockStats
and virDomainBlockInfo in the QEMU driver.
The virDomainBlockInfo API stopped working for inactive
guests if querying a block device.
The virDomainBlockStats API did not promptly report
an error if the guest was not running in some cases.
* src/qemu/qemu_driver.c: Fix inactive guest handling
in BlockStats/Info APIs
The qemuAuditDisk calls in disk hotunplug operations were being
passed 'ret >= 0', but the code which sets ret to 0 was not yet
executed, and the error path had already jumped to the 'cleanup'
label. This meant hotunplug failures were never audited, and
hotunplug success was audited as a failure
* src/qemu/qemu_hotplug.c: Fix auditing of hotunplug
Commit 4454a9efc7 introduced bad
behaviour on the VIR_EVENT_HANDLE_ERROR condition. This condition
is only hit when an invalid FD is used in poll() (typically due
to a double-close bug). The QEMU monitor code was treating this
condition as non-fatal, and thus libvirt would poll() in a fast
loop forever burning 100% CPU. VIR_EVENT_HANDLE_ERROR must be
handled in the same way as VIR_EVENT_HANDLE_HANGUP, killing the
QEMU instance.
* src/qemu/qemu_monitor.c: Treat VIR_EVENT_HANDLE_ERROR as EOF
* src/conf/domain_conf.c, src/conf/domain_conf.h: APIs for
inserting/finding/removing virDomainLeaseDefPtr instances
* src/qemu/qemu_driver.c: Wire up hotplug/unplug for leases
* src/qemu/qemu_hotplug.h, src/qemu/qemu_hotplug.c: Support
for hotplug and unplug of leases
Some lock managers associate state with leases, allowing a process
to temporarily release its leases, and re-acquire them later, safe
in the knowledge that no other process has acquired + released the
leases in between.
This is already used between suspend/resume operations, and must
also be used across migration. This passes the lockstate in the
migration cookie. If the lock manager uses lockstate, then it
becomes compulsory to use the migration v3 protocol to get the
cookie support.
* src/qemu/qemu_driver.c: Validate that migration v2 protocol is
not used if lock manager needs state transfer
* src/qemu/qemu_migration.c: Transfer lock state in migration
cookie XML
The QEMU integrates with the lock manager instructure in a number
of key places
* During startup, a lock is acquired in between the fork & exec
* During startup, the libvirtd process acquires a lock before
setting file labelling
* During shutdown, the libvirtd process acquires a lock
before restoring file labelling
* During hotplug, unplug & media change the libvirtd process
holds a lock while setting/restoring labels
The main content lock is only ever held by the QEMU child process,
or libvirtd during VM shutdown. The rest of the operations only
require libvirtd to hold the metadata locks, relying on the active
QEMU still holding the content lock.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h,
src/qemu/libvirtd_qemu.aug, src/qemu/test_libvirtd_qemu.aug:
Add config parameter for configuring lock managers
* src/qemu/qemu_driver.c: Add calls to the lock manager
Update the qemuDomainMigrateBegin method so that it accepts
an optional incoming XML document. This will be validated
for ABI compatibility against the current domain config,
and if this check passes, will be passed back out for use
by the qemuDomainMigratePrepare method on the target
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h,
src/qemu/qemu_migration.c: Allow custom XML to be passed
Currently the QEMU monitor I/O handler code uses errno values
to report errors. This results in a sub-optimal error messages
on certain conditions, in particular when parsing JSON strings
malformed data simply results in 'EINVAL'.
This changes the code to use the standard libvirt error reporting
APIs. The virError is stored against the qemuMonitorPtr struct,
and when a monitor API is run, any existing stored error is copied
into that thread's error local
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_text.c: Use
virError APIs for all monitor I/O handling code
Currently whenever there is any failure with parsing the monitor,
this is treated in the same was as end-of-file (ie QEMU quit).
The domain is terminated, if not already dead.
With this change, failures in parsing the monitor stream do not
result in the death of QEMU. The guest continues running unchanged,
but all further use of the monitor will be disabled.
The VMM_FAILURE event will be emitted, and the mgmt application
can decide when to kill/restart the guest to re-gain control
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h: Run a
different callback for monitor EOF vs error conditions.
* src/qemu/qemu_process.c: Emit VMM_FAILURE event when monitor
fails
* src/qemu/qemu_driver.c (qemuGetSchedulerParameters): Move
guts...
(qemuGetSchedulerParametersFlags): ...to new callback, and honor
flags more accurately.
This patch allows to modify interfaces of domain(qemu)
* src/conf/domain_conf.c src/conf/domain_conf.h src/libvirt_private.syms:
(virDomainNetInsert) : Insert a network device to domain definition.
(virDomainNetIndexByMac) : Returns an index of net device in array.
(virDomainNetRemoveByMac): Remove a NIC of passed MAC address.
* src/qemu/qemu_driver.c
(qemuDomainAttachDeviceConfig): add codes for NIC.
(qemuDomainDetachDeviceConfig): add codes for NIC.
Originally most of libvirt domain-specific calls were blocking
during a migration.
A new mechanism to allow specific calls (blkstat/blkinfo) to be
executed in such condition has been implemented.
In the long term it'd be desirable to get a more general
solution to mark further APIs as migration safe, without needing
special case code.
* src/qemu/qemu_migration.c: add some additional job signal
flags for doing blkstat/blkinfo during a migration
* src/qemu/qemu_domain.c: add a condition variable that can be
used to efficiently wait for the migration code to clear the
signal flag
* src/qemu/qemu_driver.c: execute blkstat/blkinfo using the
job signal flags during migration
When modifying the disk devices of a live domain and the domain
configuration, the function qemuDomainAttachDeviceConfig
first sets dev->data->disk to NULL. Later qemuDomainAttachDeviceLive
accesses dev->data.disk and causes a segfault.
* src/qemu/qemu_driver.c: fix qemuDomainModifyDeviceFlags() accordingly
http://lists.gnu.org/archive/html/qemu-devel/2011-05/threads.html#02162
Currently, qemu silently clips any JSON integer in the range
0x8000000000000000 - 0xffffffffffffffff (all numbers in this range
will be clipped to 0x7fffffffffffffff == LLONG_MAX).
To avoid this, pass these as signed 64 bit integers in the QMP
request.
The current virDomainMigrateFinish3 method signature attempts to
distinguish two types of errors, by allowing return with ret== 0,
but ddomain == NULL, to indicate a failure to start the guest.
This is flawed, because when ret == 0, there is no way for the
virErrorPtr details to be sent back to the client.
Change the signature of virDomainMigrateFinish3 so it simply
returns a virDomainPtr, in the same way as virDomainMigrateFinish2
The disk locking code will protect against the only possible
failure mode this doesn't account for (loosing conenctivity to
libvirtd after Finish3 starts the CPUs, but before the client
sees the reply for Finish3).
* src/driver.h, src/libvirt.c, src/libvirt_internal.h: Change
virDomainMigrateFinish3 to return a virDomainPtr instead of int
* src/remote/remote_driver.c, src/remote/remote_protocol.x,
daemon/remote.c, src/qemu/qemu_driver.c, src/qemu/qemu_migration.c:
Update for API change
When doing migration, if an error occurs in Perform, it must not
be overwritten during Finish/Confirm steps. If an error occurs
in Finish, it must not be overwritten in Confirm.
Previous commit a9d12c2444 added
code to qemudDomainMigrateFinish2 to preserve the error. This
is not the right place, because it is not applicable in non-p2p
migration. The src/libvirt.c virDomainMigrateV2/3 methods need
code to preserve errors for non-p2p migration, while the
doPeer2PeerMigrate2 and doPeer2PeerMigrate3 methods contain
code to preverse errors for p2p migration.
Remove the bogus error preservation from qemudDomainMigrateFinish2
and qemudDomainMigrateFinish3.
Fix virDomainMigrateV3 and doPeer2PeerMigrate3 so that they
preserve any error hit during the Finish3 step, before invoking
Confirm3.
Finally if qemuMigrationFinish fails to resume the CPUs, it must
preserve the error before tearing down the VM, so that VM cleanup
doesn't overwrite it.
* src/libvirt.c: Preserve error before invoking Confirm3
* src/qemu/qemu_driver.c: Remove bogus error preservation
code in qemudDomainMigrateFinish2/qemudDomainMigrateFinish3
* src/qemu/qemu_migration.c: Preserve error before invoking Confirm3
and after resume fails in qemuMigrationFinish.
* src/libvirt.c: Add further debug lines in helper APIs for
migration
* src/qemu/qemu_migration.c: Add debug lines for all internal
migration API parameters
Even when failing to start CPUs, the finish method was returning
a success result. Fix this so that the QEMU process is killed
off when finish fails under v3 protocol. Also rename the
killOnFinish boolean to 'v3proto' to make it clearer that this
is a tunable based on the migration protocol version
* src/qemu/qemu_driver.c: Update for API change
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Kill
VM in qemuMigrationFinish if failing to start CPUs
The SPICE seamless migration process requires data to be passed
back from the target host, to the source host via a cookie.
The cookie includes the target host's hostname, but this was not
stored, merely validated. This patch explicitly records the
remote hostname after parsing the cookie, and uses it when
initiating the SPICE migration
* qemu/qemu_migration.c: Fix SPICE seamless migration hostname
Before running perform in peer-2-peer migration, the current
guest state must be recorded, so that non-live migration can
currently unpause a running guest on completion.
* src/qemu/qemu_migration.c: Move check for offline guest
to fix non-live migration
The virDomainMigratePerform3 currently has a single URI parameter
whose meaning varies. It is either
- A QEMU migration URI (normal migration)
- A libvirtd connection URI (peer2peer migration)
Unfortunately when using peer2peer migration, without also
using tunnelled migration, it is possible that both URIs are
required.
This adds a second URI parameter to the virDomainMigratePerform3
method, to cope with this scenario. Each parameter how has a fixed
meaning.
NB, there is no way to actually take advantage of this yet,
since virDomainMigrate/virDomainMigrateToURI do not have any
way to provide the 2 separate URIs
* daemon/remote.c, src/remote/remote_driver.c,
src/remote/remote_protocol.x, src/remote_protocol-structs: Add
the second URI parameter to perform3 message
* src/driver.h, src/libvirt.c, src/libvirt_internal.h: Add
the second URI parameter to Perform3 method
* src/libvirt_internal.h, src/qemu/qemu_migration.c,
src/qemu/qemu_migration.h: Update to handle URIs correctly
This extends the v3 migration protocol such that the
virDomainMigrateBegin3 and virDomainMigratePerform3
methods accept an application supplied XML config for
the target VM.
If the 'xmlin' parameter is NULL, then Begin3 uses the
current guest XML as normal. A driver implementing the
Begin3 method should either reject all non-NULL 'xmlin'
parameters, or strictly validate that the app supplied
XML does not change guest ABI.
The Perform3 method also needed the xmlin parameter to
cope with the Peer2Peer migration sequence.
NB it is not yet possible to use this capability since
neither of the public virDomainMigrate/virDomainMigrateToURI
methods have a way to pass in XML.
* daemon/remote.c, src/remote/remote_driver.c,
src/remote/remote_protocol.x, src/remote_protocol-structs:
Add 'remote_string xmlin' parameter to begin3/perform3
RPC messages
* src/libvirt.c, src/driver.h, src/libvirt_internal.h: Add
'const char *xmlin' parameter to Begin3/Perform3 methods
* src/qemu/qemu_driver.c, src/qemu/qemu_migration.c,
src/qemu/qemu_migration.h: Pass xmlin parameter around
migration methods
Saving domain to previously created file changes also its ownership.
This is certainly not what users want if some conditions are met:
it is a regular, local file and dynamic_ownership is off.
NB: the enum that uses the string vnet-host (now changed to vhost-net)
is used in XML, but fortunately that hasn't been in an official
release yet, so it can still be fixed.
Since -vnc uses ':' to separate the address from the port, raw
IPv6 addresses need to be escaped like [addr]:port
* src/qemu/qemu_command.c: Escape raw IPv6 addresses with []
* tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.xml: Tweak
to test Ipv6 escaping
* docs/schemas/domain.rng: Allow Ipv6 addresses, or hostnames
in <graphics> listen attributes
The qemuMigrationConfirm method shouldn't deal with final VM
cleanup, since it can be called from the peer2peer migration,
which expects to still use the 'vm' object afterwards.
Push the cleanup code out of qemuMigrationConfirm, into its
caller, qemuDomainMigrateConfirm3
* src/qemu/qemu_driver.c: Add VM cleanup code to
qemuDomainMigrateConfirm3
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Remove
job handling cleanup from qemuMigrationConfirm
To allow new mandatory migration cookie data to be introduced,
add support for checking supported feature flags when parsing
migration cookie.
* src/qemu/qemu_migration.c: Feature flag checking in migration
cookie parsing
This adds a streaming-video=filter|all|off attribute. It is used to change
the behavior of video stream detection in spice, the default is filter (the
default for libvirt is not to specify it - the actual default is defined in
libspice-server.so).
Usage:
<graphics type='spice' autoport='yes'>
<streaming mode='off'/>
</graphics>
Tested with the above and with tests/qemuxml2argvtest.
Signed-off-by: Alon Levy <alevy@redhat.com>
This was discussed in:
https://www.redhat.com/archives/libvir-list/2011-May/msg01370.html
The capabilities code only sets the flag to allow use of vhost-net if
kvm is detected (set if the help string contains "(qemu-kvm-" or
"(kvm-"), but actually vhost-net is available in some qemu builds that
don't have kvm in their name, so just checking for ",vhost=" is enough.
Otherwise qemu is unable to write to it, with the error:
libvir: QEMU error : internal error unable to execute QEMU command 'memsave': Could not open '/var/cache/libvirt/qemu/qemu.mem.RRNvLv'
The v2 migration protocol had a limit on cookie length that was
too small to be useful for QEMU. Avoid generating cookies with
v2 protocol, so that old libvirtd can still reliably migrate a
guest to new libvirtd uses v2 protocol.
* src/qemu/qemu_driver.c: Avoid migration cookies with v2
migration
When generating a cookie for a guest with no data, the
QEMU_MIGRATION_COOKIE_GRAPHICS flag was set even if no
graphics data was added. Avoid setting the flag unless
it was needed, also add a safety check for mig->graphics
being non-NULL
* src/qemu/qemu_migration.c: Avoid cookie crash for guest
with no graphics
Improve invalid argument checks in the size query case. The drivers already
relied on this unchecked behavior.
Relax the implementation of virDomainGet(Memory|Blkio)MemoryParameters
in the drivers and allow to pass more memory than necessary for all
parameters.
params and nparams are essential and cannot be NULL. Check this in
libvirt.c and remove redundant checks from the drivers (e.g. xend).
Instead of enforcing that nparams must point to exact same value as
returned by virDomainGetSchedulerType relax this to a lower bound
check. This is what some drivers (e.g. xen hypervisor and esx)
already did. Other drivers (e.g. xend) didn't check nparams at all
and assumed that there is enough space in params.
Unify the behavior in all drivers to a lower bound check and update
nparams to the number of valid values in params on success.
By running the doTunnelSendAll code in a separate thread, the
main thread can do qemuMigrationWaitForCompletion as with
normal migration. This in turn ensures that job signals work
correctly and that progress monitoring can be done
* src/qemu/qemu_migration.c: Run tunnelled migration in
separate thread
Cancelling the QEMU migration may cause QEMU to flush pending
data on the migration socket. This may in turn block QEMU if
nothing reads from the other end of the socket. Closing the
socket before cancelling QEMU migration avoids this possible
deadlock.
* src/qemu/qemu_migration.c: Close sockets before cancelling
migration on failure
The 'nbytes' variable was not re-initialized to the
buffer size on each iteration of the tunnelled migration
loop. While saferead() will ensure a full read, except
on EOF, it is clearer to use the real buffer size
* src/qemu/qemu_migration.c: Always read full buffer of data
The qemuMigrationWaitForCompletion method contains a loop which
repeatedly queries QEMU to check migration progress, and also
processes job signals (pause, setspeed, setbandwidth, cancel).
The tunnelled migration loop does not currently support this
functionality, but should. Refactor the code to allow it to
be used with tunnelled migration.
Implement the v3 migration protocol, which has two extra
steps, 'begin' on the source host and 'confirm' on the
source host. All other methods also gain both input and
output cookies to allow bi-directional data passing at
all stages.
The QEMU peer2peer migration method gains another impl
to provide the v3 migration. This finally allows migration
cookies to work with tunnelled migration, which is required
for Spice seamless migration & the lock manager transfer
* src/qemu/qemu_driver.c: Wire up migrate v3 APIs
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Add
begin & confirm methods, and peer2peer impl of v3
Merge the doNonTunnelMigrate2 and doTunnelMigrate2 methods
into one doPeer2PeerMigrate2 method, since they are substantially
the same. With the introduction of v3 migration, this will be
even more important, to avoid massive code duplication.
* src/qemu/qemu_migration.c: Merge tunnel & non-tunnel migration
To facilitate the introduction of the v3 migration protocol,
the doTunnelMigrate method is refactored into two pieces. One
piece is intended to mirror the flow of virDomainMigrateVersion2,
while the other is the helper for setting up sockets and processing
the data.
Previously socket setup would be done before the 'prepare' step,
so errors could be dealt with immediately, avoiding need to shut
off the destination QEMU. In the new split, socket setup is done
after the 'prepare' step. This is not a serious problem, since
the control flow already requires calling 'finish' to tear down
the destination QEMU upon several errors.
* src/qemu/qemu_migration.c:
Use the graphics information from the QEMU migration cookie to
issue a 'client_migrate_info' monitor command to QEMU. This causes
the SPICE client to automatically reconnect to the target host
when migration completes
* src/qemu/qemu_migration.c: Set data for SPICE client relocation
before starting migration on src
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
new qemuMonitorGraphicsRelocate() command
Extend the QEMU migration cookie structure to allow information
about the destination host graphics setup to be passed by to
the source host. This will enable seamless migration of any
connected graphics clients
* src/qemu/qemu_migration.c: Add graphics info to migration
cookies
* daemon/libvirtd.c: Always initialize gnutls to enable
x509 cert parsing in QEMU
The migration protocol has support for a 'cookie' parameter which
is an opaque array of bytes as far as libvirt is concerned. Drivers
may use this for passing around arbitrary extra data they might
need during migration. The QEMU driver needs to do a few things:
- Pass hostname/uuid to allow strict protection against localhost
migration attempts
- Pass SPICE/VNC server port from the target back to the source to
allow seamless relocation of client sessions
- Pass lock driver state from source to destination
This patch introduces the basic glue for handling cookies
but only includes the host/guest UUID & name.
* src/libvirt_private.syms: Export virXMLParseStrHelper
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Parsing
and formatting of migration cookies
* src/qemu/qemu_driver.c: Pass in cookie parameters where possible
* src/remote/remote_protocol.h, src/remote/remote_protocol.x: Change
cookie max length to 16384 bytes
The qemuMigrationPrepareTunnel method should not unlock the
qemu driver, since that is the caller's job.
* src/qemu/qemu_migration.c: Fix qemuMigrationPrepareTunnel
unlocking of QEMU driver
Change all the driver struct initializers to use the
C99 style, leaving out unused fields. This will make
it possible to add new APIs without changing every
driver. eg change:
qemudDomainResume, /* domainResume */
qemudDomainShutdown, /* domainShutdown */
NULL, /* domainReboot */
qemudDomainDestroy, /* domainDestroy */
to
.domainResume = qemudDomainResume,
.domainShutdown = qemudDomainShutdown,
.domainDestroy = qemudDomainDestroy,
And get rid of any existing C99 style initializersr which
set NULL, eg change
.listPools = vboxStorageListPools,
.numOfDefinedPools = NULL,
.listDefinedPools = NULL,
.findPoolSources = NULL,
.poolLookupByName = vboxStoragePoolLookupByName,
to
.listPools = vboxStorageListPools,
.poolLookupByName = vboxStoragePoolLookupByName,
Fix some driver names:
s/virDrvCPUCompare/virDrvCompareCPU/
s/virDrvCPUBaseline/virDrvBaselineCPU/
s/virDrvQemuDomainMonitorCommand/virDrvDomainQemuMonitorCommand/
s/virDrvSecretNumOfSecrets/virDrvNumOfSecrets/
s/virDrvSecretListSecrets/virDrvListSecrets/
And some driver struct field names:
s/getFreeMemory/nodeGetFreeMemory/
Only in drivers which use virDomainObj, drivers that query hypervisor
for domain status need to be updated separately in case their hypervisor
supports this functionality.
The reason is also saved into domain state XML so if a domain is not
running (i.e., no state XML exists) the reason will be lost by libvirtd
restart. I think this is an acceptable limitation.
This is needed if we want to transfer a temporary file. If the
transfer is done with iohelper, we might run into a race condition,
where we unlink() file before iohelper is executed.
* src/fdstream.c, src/fdstream.h,
src/util/iohelper.c: Add new option
* src/lxc/lxc_driver.c, src/qemu/qemu_driver.c,
src/storage/storage_driver.c, src/uml/uml_driver.c,
src/xen/xen_driver.c: Expand existing function calls
We were 31/73 on whether to translate; since less than 50% translated
and since VIR_INFO is less than VIR_WARN which also doesn't translate,
this makes sense.
* cfg.mk (sc_prohibit_gettext_markup): Add VIR_INFO, since it
falls between WARN and DEBUG.
* daemon/libvirtd.c (qemudDispatchSignalEvent, remoteCheckAccess)
(qemudDispatchServer): Adjust offenders.
* daemon/remote.c (remoteDispatchAuthPolkit): Likewise.
* src/network/bridge_driver.c (networkReloadIptablesRules)
(networkStartNetworkDaemon, networkShutdownNetworkDaemon)
(networkCreate, networkDefine, networkUndefine): Likewise.
* src/qemu/qemu_driver.c (qemudDomainDefine)
(qemudDomainUndefine): Likewise.
* src/storage/storage_driver.c (storagePoolCreate)
(storagePoolDefine, storagePoolUndefine, storagePoolStart)
(storagePoolDestroy, storagePoolDelete, storageVolumeCreateXML)
(storageVolumeCreateXMLFrom, storageVolumeDelete): Likewise.
* src/util/bridge.c (brProbeVnetHdr): Likewise.
* po/POTFILES.in: Drop src/util/bridge.c.
These VIR_XXXX0 APIs make us confused, use the non-0-suffix APIs instead.
How do these coversions works? The magic is using the gcc extension of ##.
When __VA_ARGS__ is empty, "##" will swallow the "," in "fmt," to
avoid compile error.
example: origin after CPP
high_level_api("%d", a_int) low_level_api("%d", a_int)
high_level_api("a string") low_level_api("a string")
About 400 conversions.
8 special conversions:
VIR_XXXX0("") -> VIR_XXXX("msg") (avoid empty format) 2 conversions
VIR_XXXX0(string_literal_with_%) -> VIR_XXXX(%->%%) 0 conversions
VIR_XXXX0(non_string_literal) -> VIR_XXXX("%s", non_string_literal)
(for security) 6 conversions
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
No syntactic effect; this merely silences some clang warnings.
* src/libxl/libxl_driver.c (libxlDomainSetVcpusFlags): Drop
redundant ret=0 statement.
* src/qemu/qemu_monitor_text.c (qemuMonitorTextDriveDel):
Likewise.
Introduce a virProcessKill function that can be safely called
even when the job mutex is held. This allows virDomainDestroy
to kill any VM even if it is asleep in a monitor job. The PID
will die and the thread asleep on the monitor will then wake
up releasing the job mutex.
* src/qemu/qemu_driver.c: Kill process before using qemuProcessStop
to ensure job is released
* src/qemu/qemu_process.c: Add virProcessKill for killing off
QEMU processes
This matches the public API and helps to get rid of some special
case code in the remote generator.
Rename driver API functions and XDR protocol structs.
No functional change included outside of the remote generator.
As well as taint warnings going to the main libvirt log,
add taint warnings to the per-domain logfile
Domain id=3 is tainted: high-privileges
Domain id=3 is tainted: disk-probing
Domain id=3 is tainted: shell-scripts
Domain id=3 is tainted: custom-monitor
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Enhance
qemuDomainTaint to also log to the domain logfile
* src/qemu/qemu_driver.c: Pass -1 for logFD to taint methods to
auto-append to logfile
* src/qemu/qemu_process.c: Pass open logFD at startup for taint
methods
The qemuDomainAppendLog method allows writing a formatted string
to the end of the domain logfile, optionally opening it if needed.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainAppendLog
Move the qemuProcessLogReadFD and qemuProcessLogFD methods
into qemu_domain.c, renaming them to qemuDomainCreateLog
and qemuDomainOpenLog.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainCreateLog and qemuDomainOpenLog.
* src/qemu/qemu_process.c: Remove qemuProcessLogFD
and qemuProcessLogReadFD
Wire up logging of VM tainting to the QEMU driver
- If running QEMU as root user/group or without capabilities
being cleared
- If passing custom QEMU command line args
- If issuing custom QEMU monitor commands
- If using a network interface config with an associated
shell script
- If using a disk config relying on format probing
The warnings, per-VM appear in the main libvirtd logs
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: high-privileges
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: disk-probing
The taint flags are reset when the VM is stopped.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Helper APIs
for logging taint warnings
* src/qemu/qemu_driver.c: Log tainting with custom QEMU monitor
commands and disk/net hotplug with unsupported configs
* src/qemu/qemu_process.c: Log tainting at startup based on
unsupported configs
We already have virAsprintf, so picking a similar name helps for
seeing a similar purpose. Furthermore, the prefix V before printf
generally implies 'va_list', even though this variant was '...', and
the old name got in the way of adding a new va_list version.
global rename performed with:
$ git grep -l virBufferVSprintf \
| xargs -L1 sed -i 's/virBufferVSprintf/virBufferAsprintf/g'
then revert the changes in ChangeLog-old.
The qemuMigrationToFile method was accidentally annotated for
the 'compressor' parameter to be non-null, instead of the
'path' parameter. Thus GCC with -O2, unhelpfully deleted the
entire 'if (compressor == NULL)' block of code during
optimization. Thus NULL was passed to virCommandNew() with
predictably bad results.
* src/qemu/qemu_migration.h: Fix non-null annotation to be
against path instead of compressor
To cope with the QEMU binary being changed while a VM is running,
it is neccessary to persist the original qemu capabilities at the
time the VM is booted.
* src/qemu/qemu_capabilities.c, src/qemu/qemu_capabilities.h: Add
an enum for a string rep of every capability
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Support for
storing capabilities in the domain status XML
* src/qemu/qemu_process.c: Populate & free QEMU capabilities at
domain startup
Clang warned about a dead assignment. In the process, I noticed
that we are only using the function for a bool value. I audited
all other callers in qemu_{migration,cgroup,driver,hotplug), and
all were making the call in a bool context.
Also, do bounds checking on the argument.
* src/qemu/qemu_cgroup.c (qemuSetupCgroup): Delete dead
assignment.
(qemuCgroupControllerActive): Change return type to bool.
* src/qemu/qemu_cgroup.h (qemuCgroupControllerActive): Likewise.
Clang 2.8 wasn't quite able to follow that persistentDef was
assigned earlier if (flags & VIR_DOMAIN_MEM_CONFIG) is true.
Silence this false positive, to make clang analysis easier to use.
* src/qemu/qemu_driver.c (qemudDomainSetMemoryFlags): Add an
annotation to silence clang's claim of a NULL dereference.
This code has had problems historically. As originally
written, in commit 6bcf2501 (Jun 08), it could call unlink
on a random string, nuking an unrelated file.
Then commit 182a80b9 (Sep 09), the code was rewritten to
allocate tmp, with both a use-after-free bug and a chance to
call unlink(NULL).
Commit e206946 (Mar 11) fixed the use-after-free, but not the
NULL dereference. Thanks to clang for catching this!
* src/qemu/qemu_driver.c (qemudDomainMemoryPeek): Don't call
unlink on NULL.
This commit fixes
qemu/qemu_driver.c: In function 'qemuDomainModifyDeviceFlags':
qemu/qemu_driver.c:4041:8: warning: 'ret' may be used uninitialized in this
function [-Wuninitialized]
qemu/qemu_driver.c:4013:9: note: 'ret' was declared here
The variable is set to -1 so that the error paths are taken when the code
to set it didn't get a chance to run. Without initializing it, we could
return some an undefined value from this function.
While I was at it, I made a trivial whitespace change in the same function
to improve readability.
Support update of disks by MODIFY_CONFIG
This patch includes changes for qemu's disk to support
virDomainUpdateDeviceFlags() with VIR_DOMAIN_DEVICE_MODIFY_CONFIG.
This patch adds support for CDROM/foppy disk types.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
* src/qemu/qemu_driver.c
(qemuDomainUpdateDeviceConfig): support cdrom/floppy.
Support changes of disks by MODIFY_CONFIG for qemu.
This patch includes patches for qemu's disk to support
virDomainAt(De)tachDeviceFlags with VIR_DOMAIN_DEVICE_MODIFY_CONFIG.
Other devices can be added incrementally.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
* /src/conf/domain_conf.c
(virDomainDiskIndexByName): returns array index of disk in vmdef.
(virDomainDiskRemoveByName): removes a disk which has the name in vmdef.
* src/qemu/qemu_driver.c
(qemuDomainAttachDeviceConfig): add support for Disks.
(qemuDomainDetachDeviceConfig): add support for Disks.
This patch adds functions for modify domain's persistent definition.
To do error recovery in easy way, we use a copy of vmdef and update it.
The whole sequence will be:
make a copy of domain definition.
if (flags & MODIFY_CONFIG)
update copied domain definition
if (flags & MODIF_LIVE)
do hotplug.
if (no error)
save copied one to the file and update cached definition.
else
discard copied definition.
This patch is mixuture of Eric Blake's work and mine.
From: Eric Blake <eblake@redhat.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
(virDomainObjCopyPersistentDef): make a copy of persistent vm definition
(qemuDomainAttach/Detach/UpdateDeviceConfig) : callbacks. now empty
(qemuDomainModifyDeviceFlags): add support for MODIFY_CONFIG and MODIFY_CURRENT
Steps to reproduce this bug:
1. # cat net.xml # 00:03.0 has been used
<interface type='network'>
<mac address='52:54:00:04:72:f3'/>
<source network='default'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/>
</interface>
2. # virsh attach-device vm1 net.xml
error: Failed to attach device from net.xml
error: internal error unable to reserve PCI address 0:0:3
3. # virsh attach-device vm1 net.xml
error: Failed to attach device from net.xml
error: internal error unable to execute QEMU command 'device_add': Device 'rtl8139' could not be initialized
The reason of this bug is that: we can not reserve PCI address 0:0:3 because it has
been used, but we release PCI address when we reserve it failed.
This patch strips reusable part of qemuDomainUpdateDeviceFlags()
and consolidate it to qemuDomainModifyDeviceFlags().
No functional changes.
* src/qemu/qemu_driver.c
(qemuDomainChangeDiskMediaLive) : pulled out code for updating disks.
(qemuDomainUpdateDeviceLive) : core of UpdateDevice, extracted from
UpdateDeviceFlags()
(qemuDomainModifyDeviceFlags): add support for updating device in live domain.
(qemuDomainUpdateDeviceFlags): reworked as a wrapper function of
qemuDomainModifyDeviceFlags()
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
clean up At(De)tachDeviceFlags() for consolidation.
qemuDomainAttachDeviceFlags()/qemuDomainDetachFlags()/
qemuDomainUpdateDeviceFlags() has similar logics and copied codes.
This patch series tries to unify them to use shared code when it can.
At first, clean up At(De)tachDeviceFlags() and devide it into functions.
By this, this patch pulls out shared components between functions.
Based on patch series by Eric Blake, I added some modification as
switch-case with QEMU_DEVICE_ATTACH, QEMU_DEVICE_DETACH, QEMU_DEVICE_UPDATE
* src/qemu/qemu_driver.c
(qemuDomainAt(De)tachDeviceFlags) : pulled out to qemuDomainModifyDeviceFlags()
(qemuDomainModifyDeviceFlags) : implements generic code for modifying domain.
(qemuDomainAt(De)tachDeviceFlagsLive) : code for at(de)taching devices to
domain in line. no changes in logic from old code.
(qemuDomainAt(De)tachDeviceDiskLive) : for at(de)taching Disks.
(qemuDomainAt(De)tachDeviceControllerLive) : for at(de)taching Controllers
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Centralize device modification in the more flexible APIs, to allow future
honoring of additional flags. Explicitly reject the
VIR_DOMAIN_DEVICE_MODIFY_FORCE flag on attach/detach.
Based on Eric Blake<eblake@redhat.com>'s work.
* src/qemu/qemu_driver.c
(qemudDomainAttachDevice)(qemudDomainAttachDeviceFlags): Swap bodies,rename...
(qemudDomainDetachDevice, qemudDomainDetachDeviceFlags): Likewise.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
The two ends of the pipe used for feeding QEMU tunnelled
migration data were interchanged, so QEMU got given the
"write" end instead of the "read" end.
The qemuMigrationPrepareTunnel method was also immediately
closing the "write" end of the pipe, so the stream failed
to actually write anything.
* src/qemu/qemu_migration.c: Swap tunnelled migration
pipe FDs & don't close pipe given to stream
