Several tests are intending to test some serial/console related
bits but aren't setting QEMU_CAPS_CHARDEV. This will soon be enabled
unconditionally so let's add it ahead of time.
* q35-virt-manager-basic: Intended to test a virt-manager q35 config,
which will include a serial/console device
* console-compat*: console/serial XML compat handling
* bios: Needs a serial device for sgabios CLI
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The capabilities used in test cases should match those used
during normal operation for the tests to make any sense.
This results in the generated command line for a few test
cases (most notably non-x86 test cases that were wrongly
assuming they could use -no-acpi) changing.
Set the VIR_PCI_CONNECT_AGGREGATE_SLOT flag for pcie-root-ports so
that they will be assigned to all the functions on a slot.
Some qemu test case outputs had to be adjusted due to the
pcie-root-ports now being put on multiple functions.
For machinetypes with a pci-root bus (all legacy PCI), libvirt will
make a "fake" reservation for one extra slot prior to assigning
addresses to unaddressed PCI endpoint devices in the domain. This will
trigger auto-adding of a pci-bridge for the final device to be
assigned an address *if that device would have otherwise instead been
the last device on the last available pci-bridge*; thus it assures
that there will always be at least one slot left open in the domain's
bus topology for expansion (which is important both for hotplug (since
a new pci-bridge can't be added while the guest is running) as well as
for offline additions to the config (since adding a new device might
otherwise in some cases require re-addressing existing devices, which
we want to avoid)).
It's important to note that for the above case (legacy PCI), we must
check for the special case of all slots on all buses being occupied
*prior to assigning any addresses*, and avoid attempting to reserve
the extra address in that case, because there is no free address in
the existing topology, so no place to auto-add a pci-bridge for
expansion (i.e. it would always fail anyway). Since that condition can
only be reached by manual intervention, this is acceptable.
For machinetypes with pcie-root (Q35, aarch64 virt), libvirt's
methodology for automatically expanding the bus topology is different
- pcie-root-ports are plugged into slots (soon to be functions) of
pcie-root as needed, and the new endpoint devices are assigned to the
single slot in each pcie-root-port. This is done so that the devices
are, by default, hotpluggable (the slots of pcie-root don't support
hotplug, but the single slot of the pcie-root-port does). Since
pcie-root-ports can only be plugged into pcie-root, and we don't
auto-assign endpoint devices to the pcie-root slots, this means
topology expansion doesn't compete with endpoint devices for slots, so
we don't need to worry about checking for all "useful" slots being
free *prior* to assigning addresses to new endpoint devices - as a
matter of fact, if we attempt to reserve the open slots before the
used slots, it can lead to errors.
Instead this patch just reserves one slot for a "future potential"
PCIe device after doing the assignment for actual devices, but only
if the only PCI controller defined prior to starting address
assignment was pcie-root, and only if we auto-added at least one PCI
controller during address assignment. This assures two things:
1) that reserving the open slots will only be done when the domain is
initially defined, never at any time after, and
2) that if the user understands enough about PCI controllers that they
are adding them manually, that we don't mess up their plan by
adding extras - if they know enough to add one pcie-root-port, or
to manually assign addresses such that no pcie-root-ports are
needed, they know enough to add extra pcie-root-ports if they want
them (this could be called the "libguestfs clause", since
libguestfs needs to be able to create domains with as few
devices/controllers as possible).
This is set to reserve a single free port for now, but could be
increased in the future if public sentiment goes in that direction
(it's easy to increase later, but essentially impossible to decrease)
Real Q35 hardware has an ICH9 chip that includes several integrated
devices at particular addresses (see the file docs/q35-chipset.cfg in
the qemu source). libvirt already attempts to put the first two sets
of ich9 USB2 controllers it finds at 00:1D.* and 00:1A.* to match the
real hardware. This patch does the same for the ich9 "HD audio"
device.
The main inspiration for this patch is that currently the *only*
device in a reasonable "workstation" type virtual machine config that
requires a legacy PCI slot is the audio device, Without this patch,
the standard Q35 machine created by virt-manager will have a
dmi-to-pci-bridge and a pci-bridge just for the sound device; with the
patch (and if you change the sound device model from the default
"ich6" to "ich9"), the machine definition constructed by virt-manager
has absolutely no legacy PCI controllers - any legacy PCI devices
(e.g. video and sound) are on pcie-root as integrated devices.
