In commit 45ad1adb I added a nicer message for tunings that need
cgroups when unavailable (unprivileged), but I added this check for
I/O tuning of block devices, which doesn't need cgroups, because it is
done by QEMU, so let's fix that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Fix a comment in virDomainAuditNetDevice.
Fix a typo in comment of qemuPhysIfaceConnect which is
the caller of virDomainAuditNetDevice.
Signed-off-by: Wang Rui <moon.wangrui@huawei.com>
Otherwise this beautiful error would be overwritten when
the function is called with a really high rate number:
2014-07-28 12:51:47.920+0000: 2304: error : virCommandWait:2399 :
internal error: Child process (/sbin/tc class add dev vnet0 parent 1:
classid 1:1 htb rate 4294968kbps) unexpected exit status 1: Illegal "rate"
Usage: ... qdisc add ... htb [default N] [r2q N]
default minor id of class to which unclassified packets are sent {0}
r2q DRR quantums are computed as rate in Bps/r2q {10}
debug string of 16 numbers each 0-3 {0}
... class add ... htb rate R1 [burst B1] [mpu B] [overhead O]
[prio P] [slot S] [pslot PS]
[ceil R2] [cburst B2] [mtu MTU] [quantum Q]
rate rate allocated to this class (class can still borrow)
burst max bytes burst which can be accumulated during idle period {computed}
mpu minimum packet size used in rate computations
overhead per-packet size overhead used in rate computations
linklay adapting to a linklayer e.g. atm
ceil definite upper class rate (no borrows) {rate}
cburst burst but for ceil {computed}
mtu max packet size we create rate map for {1600}
prio priority of leaf; lowe
https://bugzilla.redhat.com/show_bug.cgi?id=1043735
If PCI passthrough type is not supported, we should error out rather than
continue building the command line.
When starting a domain, the type has been already checked by
qemuPrepareHostdevPCICheckSupport() before building qemu command line,
so the problem doesn't emerge.
But when coverting a domain xml without specifying passthrough type explictly
to qemu arg, we will get a malformed command line.
the xml:
<hostdev mode='subsystem' type='pci' managed='yes'>
<source>
<address domain='0x0001' bus='0x03' slot='0x00' function='0x0'/>
</source>
<address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/>
</hostdev>
the converted command line:
-device ,host=0001:03:00.0,id=hostdev0,bus=pci.0,addr=0x5
After this patch, virsh gives an error message:
virsh domxml-to-native qemu-argv /tmp/tmp.xml
error: internal error: invalid PCI passthrough type 'default'
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Use better detection of hugetlbfs mount points. Yes, there can be
multiple mount points each serving different huge page size.
Since we already have ability to override the mount point in the
qemu.conf file, this crazy backward compatibility code is brought in.
Now we allow multiple mount points, so the "hugetlbfs_mount" option
must take an list of strings (mount points). But previously, it was
just a string, so we must accept both types now.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Commit e5f36698e3 introduces a
false-positive build failure in the sound card model handling switch.
Initialize the model to NULL although the value should never be used.
Libvirt documents that the default entropy source for the 'random'
backend of a RNG device is /dev/random. Instead of storing and
propagating NULL across our code and checking it in multiple places fill
the default in the post parse callback and use that in the other places.
Create the structures and API's to hold and manage the iSCSI host device.
This extends the 'scsi_host' definitions added in commit id '5c811dce'.
A future patch will add the XML parsing, but that code requires some
infrastructure to be in place first in order to handle the differences
between a 'scsi_host' and an 'iSCSI host' device.
Split virDomainHostdevSubsysSCSI further. In preparation for having
either SCSI or iSCSI data, create a union in virDomainHostdevSubsysSCSI
to contain just a virDomainHostdevSubsysSCSIHost to describe the
'scsi_host' host device
Currently, we only bind the whole QEMU domain to memory nodes
specified in nodemask altogether. That, however, doesn't make much
sense when one wants to control from where the memory for particular
guest nodes should be allocated. QEMU allows us to do that by
specifying 'host-nodes' parameter for the 'memory-backend-ram' object,
so let's use that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In XML format, by definition, order of fields should not matter, so
order of parsing the elements doesn't affect the end result. When
specifying guest NUMA cells, we depend only on the order of the 'cell'
elements. With this patch all older domain XMLs are parsed as before,
but with the 'id' attribute they are parsed and formatted according to
that field. This will be useful when we have tuning settings for
particular guest NUMA node.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Excerpt from the virCommandAddArgBuffer() description: "Correctly
transfers memory errors or contents from buf to cmd."
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This patch adds support for the QEMU vhost-user feature to libvirt.
vhost-user enables the communication between a QEMU virtual machine
and other userspace process using the Virtio transport protocol.
It uses a char dev (e.g. Unix socket) for the control plane,
while the data plane based on shared memory.
The XML looks like:
<interface type='vhostuser'>
<mac address='52:54:00:3b:83:1a'/>
<source type='unix' path='/tmp/vhost.sock' mode='server'/>
<model type='virtio'/>
</interface>
Signed-off-by: Michele Paolino <m.paolino@virtualopensystems.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Qemu will fallback to aio=threads when the cache mode doesn't use
O_DIRECT, even if aio=native was explictly set.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1086704
Signed-off-by: Giuseppe Scrivano <gscrivan@redhat.com>
In the future we might need to track state of individual images. Move
the readonly and shared flags to the virStorageSource struct so that we
can keep them in a per-image basis.
Replace the inline "auth" struct in virStorageSource with a pointer
to a virStorageAuthDefPtr and utilize between the domain_conf, qemu_conf,
and qemu_command sources for finding the auth data for a domain disk
Replace:
if (virBufferError(&buf)) {
virBufferFreeAndReset(&buf);
virReportOOMError();
...
}
with:
if (virBufferCheckError(&buf) < 0)
...
This should not be a functional change (unless some callers
misused the virBuffer APIs - a different error would be reported
then)
This introduces two new attributes "cmd_per_lun" and "max_sectors" same
with the names QEMU uses for virtio-scsi. An example of the XML:
<controller type='scsi' index='0' model='virtio-scsi' cmd_per_lun='50'
max_sectors='512'/>
The corresponding QEMU command line:
-device virtio-scsi-pci,id=scsi0,cmd_per_lun=50,max_sectors=512,
bus=pci.0,addr=0x3
Signed-off-by: Mike Perez <thingee@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
The IDE bus doesn't support readonly disks, so inform the user with an
error message instead of let qemu fail with a more obscure "Device
'ide-hd' could not be initialized" error message.
Closes: https://bugzilla.redhat.com/show_bug.cgi?id=1112939
Signed-off-by: Giuseppe Scrivano <gscrivan@redhat.com>
Since commit d86c876a66 we are using
guestfwd=tcp:IP:PORT,chardev=ID for guestfwd specification, however,
that has not changed in qemu, so guestfwd does not work since.
Apart from that, guestfwd is not working with older qemu that doesn't
have QEMU_CAPS_DEVICE.
Both regressions exist since late 2009 and nobody found that (until
now), so I'm only fixing the first one.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1112066
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The QEMU VNC client arg code has a long standing typo
of SASL_CONF_DIR when it should be SASL_CONF_PATH for
the env variable name.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
There are no options to parse here other than the name of the device,
and all three possible device names have the same prefix
("virtio-balloon" with "-ccw", "-pci", or "-device" appended), so the
code is fairly simple. It has been implemented such that it will be
easier to add handling for other -device entries that aren't otherwise
recognized - just add another "else if (STRPREFIX(opts, ....)" clause.
qemuParseCommandLineString() previously would always add a <memballoon
model='virtio'/> to every result (the comments erroneously say that it
is adding a <memballoon model='none'/>) This has been changed to add
model='none', and 84 test case xml's updated accordingly (so that
qemuxml2argvtest won't fail).
Now that the memballoon device is properly parsed, we can safely add a
test for properly ignoring -nodefconfig and -nodefaults. Rather than
adding an entire new test case for this (and memballoon), we just
randomly pick the clock-utc test and modify it slightly to fulfill the
purpose.
The qemu driver always adds these options to the qemu commandlines,
but the commandline parser didn't recognize them, so sending a
libvirt-generated qemu commandline to its own argvtoxml would always
result in a warning message and a qemu namespace added to the
xml. Since the options don't add any functionality to the domain, they
should just be ignored (similar to -S).
Note that we can't yet add a test for this to qemuargv2xmltest,
because we would have to add QEMU_CAPS_NODEFCONFIG and
QEMU_CAPS_DEVICE to the capabilities for any corresponding
xml2argvtest, and QEMU_CAPS_DEVICE would necessitate having support
for parsing a memballoon device in order for qemuargv2xmltest to
pass. So we wait to add a test for -nodefconfig and -nodefaults until
after adding support for parsing -device virtio-balloon-*.
As part of the work on backing chains, I'm finding that it would
be easier to directly manipulate chains of pointers (adding a
snapshot merely adjusts pointers to form the correct list) rather
than copy data from one struct to another. This patch converts
domain disk source to be a pointer.
In this patch, the pointer is ALWAYS allocated (thanks in part to
the previous patch forwarding all disk def allocation through a
common point), and all other changse are just mechanical fallout of
the new type; there should be no functional change. It is possible
that we may want to leave the pointer NULL for a cdrom with no
medium in a later patch, but as that requires a closer audit of the
source to ensure we don't fault on a null dereference, I didn't do
it here.
* src/conf/domain_conf.h (_virDomainDiskDef): Change type of src.
* src/conf/domain_conf.c: Adjust all clients.
* src/security/security_selinux.c: Likewise.
* src/qemu/qemu_domain.c: Likewise.
* src/qemu/qemu_command.c: Likewise.
* src/qemu/qemu_conf.c: Likewise.
* src/qemu/qemu_process.c: Likewise.
* src/qemu/qemu_migration.c: Likewise.
* src/qemu/qemu_driver.c: Likewise.
* src/lxc/lxc_driver.c: Likewise.
* src/lxc/lxc_controller.c: Likewise.
* tests/securityselinuxlabeltest.c: Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
A future patch wants to create disk definitions with non-zero
default contents; to avoid crashes, all callers that allocate
a disk definition should go through a common point.
I found allocation points by looking for any code that increments
ndisks, as well as any matches for ALLOC.*disk. Most places that
modified ndisks were covered by the parse from XML to domain/device
definition by initial domain creation or device hotplug; I also
hand-checked all drivers that generate a device struct on the
fly during getXMLDesc.
* src/conf/domain_conf.h (virDomainDiskDefNew): New prototype.
* src/conf/domain_conf.c (virDomainDiskDefNew): New function.
(virDomainDiskDefParseXML): Use it.
* src/parallels/parallels_driver.c (parallelsAddHddInfo):
Likewise.
* src/qemu/qemu_command.c (qemuParseCommandLine): Likewise.
* src/vbox/vbox_tmpl.c (vboxDomainGetXMLDesc): Likewise.
* src/vmx/vmx.c (virVMXParseDisk): Likewise.
* src/xenxs/xen_sxpr.c (xenParseSxprDisks, xenParseSxpr):
Likewise.
* src/xenxs/xen_xm.c (xenParseXM): Likewise.
* src/libvirt_private.syms (domain_conf.h): Export it.
Signed-off-by: Eric Blake <eblake@redhat.com>
In "src/conf/domain_conf.h" there are many enum declarations. The
cleanup in this header filer was started, but it wasn't enough and
there are many other files that has enum variables declared. So, the
commit was starting to be big. This commit finish the cleanup in this
header file and in other files that has enum variables, parameters,
or functions declared.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
In "src/conf/domain_conf.h" there are many enumerations (enum)
declarations to be converted as a typedef too. As mentioned before,
it's better to use a typedef for variable types, function types and
other usages. I think this file has most of those enum declarations
at "src/conf/". So, me and Eric Blake plan to keep the cleanups all
over the source code. This time, most of the files changed in this
commit are related to part of one file: "src/conf/domain_conf.h".
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
For a clock element as above, libvirt simply converts current system
time with localtime_r(), then starts qemu with a time string that
doesn't contain any timezone information. So, from qemu's point of
view, the -rtc string it gets for:
<clock offset='variable' basis='utc' adjustment='10800'/>
is identical to the -rtc string it gets for:
<clock offset='variable' basis='localtime' adjustment='0'/>
(assuming the host is in a timezone that is 10800 seconds ahead of
UTC, as is the case on the machine where this message is being
written).
Since the commandlines are identical, qemu will behave identically
after this point in either case.
There are two problems in the case of basis='localtime' though:
Problem 1) If the guest modifies its RTC, for example to add 20
seconds, the RTC_CHANGE event from qemu will then contain offset:20 in
both cases. But libvirt will have saved the original adjustment into
adjustment0, and will add that value onto the offset in the
event. This means that in the case of basis=;utc', it will properly
emit an event with offset:10820, but in the case of basis='localtime'
the event will contain offset:20, which is *not* the new offset of the
RTC from UTC (as the event it documented to provide).
Problem 2) If the guest is migrated to another host that is in a
different timezone, or if it is migrated or saved/restored after the
DST status has changed from what it was when the guest was originally
started, the newly restarted guest will have a different RTC (since it
will be based on the new localtime, which could have shifted by
several hours).
The solution to both of these problems is simple - rather than
maintaining the original adjustment value along with
"basis='localtime'" in the domain status, when the domain is started
we convert the adjustment offset to one relative to UTC, and set the
status to "basis='utc'". Thus, whatever the RTC offset was from UTC
when it was initially started, that offset will be maintained when
migrating across timezones and DST settings, and the RTC_CHANGE events
will automatically contain the proper offset (which should by
definition always be relative to UTC).
This fixes a problem that was implied but not openly stated in:
https://bugzilla.redhat.com/show_bug.cgi?id=964177
commit e31b5cf393 attempted to fix libvirt's
VIR_DOMAIN_EVENT_ID_RTC_CHANGE, which is documentated to always
provide the new offset of the domain's real time clock from UTC. The
problem was that, in the case that qemu is provided with an "-rtc
base=x" where x is an absolute time (rather than "utc" or
"localtime"), the offset sent by qemu's RTC_CHANGE event is *not* the
new offset from UTC, but rather is the sum of all changes to the
domain's RTC since it was started with base=x.
So, despite what was said in commit e31b5cf393, if we assume that
the original value stored in "adjustment" was the offset from UTC at
the time the domain was started, we can always determine the current
offset from UTC by simply adding the most recent (i.e. current) offset
from qemu to that original adjustment.
This patch accomplishes that by storing the initial adjustment in the
domain's status as "adjustment0". Each time a new RTC_CHANGE event is
received from qemu, we simply add adjustment0 to the value sent by
qemu, store that as the new adjustment, and forward that value on to
any event handler.
This patch (*not* e31b5cf393, which should be reverted prior to
applying this patch) fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=964177
(for the case where basis='utc'. It does not fix basis='localtime')
This reverts commit e31b5cf393.
This commit attempted to work around a bug in the offset value
reported by qemu's RTC_CHANGE event in the case that a variable base
date was given on the qemu commandline. The patch mixed up the math
involved in arriving at the corrected offset to report, and in the
process added an unnecessary private attribute to the clock
element. Since that element is private/internal and not used by anyone
else, it makes sense to simplify things by removing it.
Currently the protocol type with index 0 was NBD which made it hard to
distinguish whether the protocol type was actually assigned. Add a new
protocol type with index 0 to distinguish it explicitly.
The gluster volume name was previously stored as part of the source path
string. This is unfortunate when we want to do operations on the path as
the volume is used separately.
Parse and store the volume name separately for gluster storage volumes
and use the newly stored variable appropriately.
This partially reverts commits b279e52f7 and ea18f8b2.
It turns out our code base is full of:
if ((struct.member = virBlahFromString(str)) < 0)
goto error;
Meanwhile, the C standard says it is up to the compiler whether
an enum is signed or unsigned when all of its declared values
happen to be positive. In my testing (Fedora 20, gcc 4.8.2),
the compiler picked signed, and nothing changed. But others
testing with gcc 4.7 got compiler warnings, because it picked
the enum to be unsigned, but no unsigned value is less than 0.
Even worse:
if ((struct.member = virBlahFromString(str)) <= 0)
goto error;
is silently compiled without warning, but incorrectly treats -1
from a bad parse as a large positive number with no warning; and
without the compiler's help to find these instances, it is a
nightmare to maintain correctly. We could force signed enums
with a dummy negative declaration in each enum, or cast the
result of virBlahFromString back to int after assigning to an
enum value, or use a temporary int for collecting results from
virBlahFromString, but those actions are all uglier than what we
were trying to cure by directly using enum types for struct
values in the first place. It's better off to just live with int
members, and use 'switch ((virFoo) struct.member)' where we want
the compiler to help, than to track down all the conversions from
string to enum and ensure they don't suffer from type problems.
* src/util/virstorageencryption.h: Revert back to int declarations
with comment about enum usage.
* src/util/virstoragefile.h: Likewise.
* src/conf/domain_conf.c: Restore back to casts in switches.
* src/qemu/qemu_driver.c: Likewise.
* src/qemu/qemu_command.c: Add cast rather than revert.
Signed-off-by: Eric Blake <eblake@redhat.com>
For internal structs, we might as well be type-safe and let the
compiler help us with less typing required on our part (getting
rid of casts is always nice). In trying to use enums directly,
I noticed two problems in virstoragefile.h that can't be fixed
without more invasive refactoring: virStorageSource.format is
used as more of a union of multiple enums in storage volume
code (so it has to remain an int), and virStorageSourcePoolDef
refers to pooltype whose enum is declared in src/conf, but where
src/util can't pull in headers from src/conf.
* src/util/virstoragefile.h (virStorageNetHostDef)
(virStorageSourcePoolDef, virStorageSource): Use enums instead of
int for fields of internal types.
* src/qemu/qemu_command.c (qemuParseCommandLine): Cover all values.
* src/conf/domain_conf.c (virDomainDiskSourceParse)
(virDomainDiskSourceFormat): Simplify clients.
* src/qemu/qemu_driver.c
(qemuDomainSnapshotCreateSingleDiskActive)
(qemuDomainSnapshotPrepareDiskExternalBackingInactive)
(qemuDomainSnapshotPrepareDiskExternalOverlayActive)
(qemuDomainSnapshotPrepareDiskInternal): Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Move sharable PCI handling functions to domain_addr.[ch], and
change theirs prefix from 'qemu' to 'vir':
- virDomainPCIAddressAsString;
- virDomainPCIAddressBusSetModel;
- virDomainPCIAddressEnsureAddr;
- virDomainPCIAddressFlagsCompatible;
- virDomainPCIAddressGetNextSlot;
- virDomainPCIAddressReleaseSlot;
- virDomainPCIAddressReserveAddr;
- virDomainPCIAddressReserveNextSlot;
- virDomainPCIAddressReserveSlot;
- virDomainPCIAddressSetFree;
- virDomainPCIAddressSetGrow;
- virDomainPCIAddressSlotInUse;
- virDomainPCIAddressValidate;
The only change here is function names, the implementation itself
stays untouched.
Extract common allocation code from DomainPCIAddressSetCreate
into virDomainPCIAddressSetAlloc.
