The device xml parser code does not set "model" while parsing the
following XML:
<interface type='hostdev'>
<source>
<address type='pci' domain='0x0002' bus='0x01' slot='0x00' function='0x2'/>
</source>
</interface>
The net->model can be NULL and therefore must be compared using
STREQ_NULLABLE instead of plain STREQ.
Fixes: ac47e4a622 (qemu: replace "def->nets[i]" with "net" and "def->sounds[i]" with "sound")
Fixes: c7fc151eec (qemu: assign virtio devices to PCIe slot when appropriate)
Signed-off-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Removing redundant sections of the code
Signed-off-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
libvirt wrongly assumes that VF netdev has to have the
netdev assigned to PF. There is no such requirement in SRIOV standard.
This patch change the virNetDevSwitchdevFeature() function to deal
with SRIOV devices which does not have netdev on PF. Also corrects
one comment about PF netdev assumption.
One example of such devices is ThunderX VNIC.
By applying this change, VF device is used for virNetlinkCommand() as
it is the only netdev assigned to VNIC.
Signed-off-by: Radoslaw Biernacki <radoslaw.biernacki@linaro.org>
Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This adds the virt-aa-helper support for gl enabled graphics devices to
generate rules for the needed rendernode paths.
Example in domain xml:
<graphics type='spice'>
<gl enable='yes' rendernode='/dev/dri/bar'/>
</graphics>
results in:
"/dev/dri/bar" rw,
Special cases are:
- multiple devices with rendernodes -> all are added
- non explicit rendernodes -> follow recently added virHostGetDRMRenderNode
- rendernode without opengl (in egl-headless for example) -> still add
the node
Fixes: https://bugs.launchpad.net/ubuntu/+source/libvirt/+bug/1757085
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Acked-by: Jamie Strandboge <jamie@canonical.com>
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Add a capability check to qemuDomainDefValidate and refuse to start
a domain with VNC graphics if the TLS secret was set in qemu.conf
and it's not supported.
Note that qemuDomainSecretGraphicsPrepare does not generate any
secret data if the capability is not present and qemuBuildTLSx509BackendProps
is not called at all.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Use the password stored in the secret driver under
the uuid specified by the vnc_tls_x509_secret_uuid
option in qemu.conf.
https://bugzilla.redhat.com/show_bug.cgi?id=1602418
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Add an option that lets the user specify the secret
that unlocks the server TLS key.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Be generic instead of trying to enumerate all the involved
device types.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Instead of hardcoding the TLS creds alias in
qemuBuildGraphicsVNCCommandLine, store it
in the domain private data.
Given that we only support one VNC graphics
and thus have only one alias per-domain,
this is overengineered, but it will allow us
to prepare the secret upfront when we start
supporting encrypted server TLS keys.
Note that the alias is not formatted anywhere
since we won't need to access it after domain
startup.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
A helper function for allocating the virDomainGraphicsDef structure.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
The %{extra_release} field was previously populated by data from the old
autobuild.sh file but is no longer used.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The next release of QEMU is going to be 4.0.0. A bit early, but
this adds capabilities data for x86_64 from current qemu git
15bede554162dda822cd762c689edb6fa32b6e3b
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
PolicyKit authentication rules have switched to a JavaScript based
format quite some time ago. See:
http://davidz25.blogspot.com/2012/06/authorization-rules-in-polkit.html
While backwards compat for the old .pkla format is still available, it
makes sense to point people first at the new format.
The SSHPolicyKitSetup wiki page seems pretty stale, so remove the
reference to it.
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Switch the function to use VIR_AUTOFREE and VIR_AUTOPTR macros
to get rid of the cleanup section.
Requested-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Switch the function to use VIR_AUTOFREE and VIR_AUTOPTR macros
to get rid of the cleanup section.
Requested-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Switch the function to use VIR_AUTOFREE and VIR_AUTOPTR macros
to get rid of the cleanup section.
Requested-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Switch the function to use VIR_AUTOFREE and VIR_AUTOPTR macros
to get rid of the cleanup section.
Requested-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
If a -drive has no image, using image properties makes qemu whine that
they should not be used.
This patch stops formating cache/readonly/... for empty drives
for the pre-blockdev syntax. Unfortunately those parameters can't be
added later when inserting media, but on the other hand qemu will start
with an empty drive.
Since we already were able to start a VM with such config previously due
to qemu ignoring them I've opted just to skip formatting them.
Additionally with -blockdev support it will work as expected as the
image properties will be formatted when adding the image itself which is
not possible without it.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1651457
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Upcomming change will influence CDROM with cache mode so add a test
case.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Ceph in upstream and Fedora has dropped support for building on host
architectures which are 32-bit.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
When commit 361c8dc17 added support for hotplugging the i6300esb
watchdog device (first in libvirt-3.9.0), it accidentally contstructed
the commandline for the device_add command before allocating a PCI
address for the device. With no PCI address specified in the command,
the watchdog would simply be placed at the lowest unused PCI slot.
On a 440fx guest, this doesn't cause a problem, because libvirt's PCI
address allocation algorithm would most likely give the same address
anyway (usually a slot on pci-root), so nobody noticed the omission of
address from the command.
But on a Q35 guest, the lowest unused PCI slot is on pcie-root, which
doesn't support hotplug; libvirt knows enough to assign a PCI address
that is on a pcie-to-pci-bridge (because its slots *do* support
hotplug), but qemu doesn't, so if there is no PCI address in the
command, qemu just tries to plug the new device into pcie-root, and
fails because it doesn't support hotplug, e.g.:
error: Failed to attach device from watchdog.xml
error: internal error: unable to execute QEMU command 'device_add':
Bus 'pcie.0' does not support hotplugging
The solution is simply to build the command string after assigning a
PCI address, not before.
Resolves: https://bugzilla.redhat.com/1666559
Signed-off-by: Laine Stump <laine@laine.org>
Reviewed-by: John Ferlan <jferlan@redhat.com>
If code in the @actualType switch needs to have/know which PCI
Address is being used, then we must assign it earlier. In particular
a vhost-user device needs to call qemuDomainSupportsNicdev which
requires an address to be defined.
Signed-off-by: Wang Yechao <wang.yechao255@zte.com.cn>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
This is the only patch that mixes various augeas entry
groups in one function.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
Split out parts of the config parsing code to make
the parent function easier to read.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: John Ferlan <jferlan@redhat.com>
if virNetClientNew finishes with error before sock is set
to client object then sock does not get unrefed. This is
unexpected by function clients like virNetClientNewUNIX.
Let's make sure sock gets unrefed on any error path.
Next some clients like virNetClientNewLibSSH2 try to unref
sock on virNetClientNew errors. This is not correct even
before this patch because in some cases virNetClientNew
unrefed sock on error path by itself. Let's give up
sock managment to virNetClientNew entirely.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Currently the job name corresponds to the disk the job belongs to. For
jobs which will not correspond to disks we'll need to track the name
separately.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Now that the data is per-job, we don't really need to bother with
finishing the synchronous job handling if the job is already terminated.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Rather than storing the presence of the blockjob in a flag we can bind
together the lifecycle of the job with the lifecycle of the object which
is tracking the data for it.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
