To allow devices to be hot(un-)plugged it is neccessary to ensure
they all have a unique device aliases. This fixes the hotplug
methods to assign device aliases before invoking the monitor
commands which need them
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Expose methods
for assigning device aliases for disks, host devices and
controllers
* src/qemu/qemu_driver.c: Assign device aliases when hotplugging
all types of device
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-address-device.args:
Update for changed hostdev naming scheme
The current way of assigning names to the host network backend and
NIC device in QEMU was over complicated, by varying naming scheme
based on the NIC model and backend type. This simplifies the naming
to simply be 'net0' and 'hostnet0', allowing code to easily determine
the host network name and vlan based off the primary device alias
name 'net0'. This in turn allows removal of alot of QEMU specific
code from the XML parser, and makes it easier to assign new unique
names for NICs that are hotplugged
* src/conf/domain_conf.c, src/conf/domain_conf.h: Remove hostnet_name
and vlan fields from virNetworkDefPtr
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h, src/qemu/qemu_driver.c:
Use a single network alias naming scheme regardless of NIC type
or backend type. Determine VLANs from the alias name.
* tests/qemuxml2argvdata/qemuxml2argv-net-eth-names.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args: Update
for new simpler naming scheme
The QEMU 0.12.x tree has the -netdev command line argument, but not
corresponding monitor command. We can't enable the former, without
the latter since it will break hotplug/unplug.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Disable -netdev usage
until 0.13 at earliest
* tests/qemuxml2argvtest.c: Add test for -netdev syntax
* tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-netdev.xml: Test
data files for -netdev syntax
The current QEMU code allocates PCI addresses incrementally starting
at 4. This is not satisfactory because the user may have given some
addresses in their XML config, which need to be skipped over when
allocating addresses to remaining devices.
It is thus neccessary to maintain a list of already allocated PCI
addresses and then only allocate ones that remain unused. This is
also required for domain device hotplug to work properly later.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Add APIs for creating
list of existing PCI addresses, and allocating new addresses.
Refactor address assignment to use this code
* src/qemu/qemu_driver.c: Pull PCI address assignment up into the
qemuStartVMDaemon() method, as a prelude to moving it into the
'define' method. Update list of allocated addresses when connecting
to a running VM at daemon startup.
* tests/qemuxml2argvtest.c, tests/qemuargv2xmltest.c,
tests/qemuxml2xmltest.c: Remove USB product test since all
passthrough is done based on address
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.args,
tests/qemuxml2argvdata/qemuxml2argv-hostdev-usb-product.xml: Kil
unused data files
The test expected all environment variables copied in qemudBuildCommandLine
to have known values. So all of them have to be either set to a known value
or be unset. SDL_VIDEODRIVER and QEMU_AUDIO_DRV are not handled at all but
should be handled. Unset both, otherwise the test will fail if they are set
in the testing environment.
* src/qemu/qemu_conf.c: add a comment about copied environment variables
and qemuxml2argvtest
* tests/qemuxml2argvtest.c: unset SDL_VIDEODRIVER and QEMU_AUDIO_DRV
The RNG now supports IPv6 and bonds attached to bridges, along with
some other minor tweaks. All test files from netcf have been copied to
the test directory and added to the xml2xml and schema tests (and they
all pass, of course ;-)
QEMU's command line equivalent for the following domain XML fragment
<vcpus>2</vcpus>
<cpu ...>
...
<topology sockets='1' cores='2', threads='1'/>
</cpu>
is
-smp 2,sockets=1,cores=2,threads=1
This syntax was introduced in QEMU-0.12.
Version 2 changes:
- -smp argument build split into a separate function
- always add ",sockets=S,cores=C,threads=T" to -smp if qemu supports it
- use qemuParseCommandLineKeywords for command line parsing
Version 3 changes:
- ADD_ARG_LIT => ADD_ARG and line reordering in qemudBuildCommandLine
- rebased
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Replace
-balloon virtio
With
-device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3
This allows it to get correct assigned PCI address as declared in
previous patch
* src/qemu/qemu_conf.c: Convert Virtio ballon to -device and
give it an explicit PCI address
* tests/qemuxml2argvdata/qemuxml2argv-*args: Add in virtio balloon
where appropriate
Instead of relying on QEMU to assign PCI addresses and then querying
them with 'info pci', manually assign all PCI addresses before starting
the guest. These addresses are not stable across reboots. That will
come in a later patch
NB, the PIIX3 (IDE, FDC, ISA-Bridge) will always have slot 1 and
VGA will always have slot 2. We declare the Virtio Balloon gets
slot 3, and then all remaining slots are for configured devices.
* src/qemu/qemu_conf.c: If -device is supported, then assign all PCI
addresses when building the command line
* src/qemu/qemu_driver.c: Don't query monitor for PCI addresses if
they have already been assigned
* tests/qemuxml2argvdata/qemuxml2argv-hostdev-pci-address-device.args,
tests/qemuxml2argvdata/qemuxml2argv-net-virtio-device.args,
tests/qemuxml2argvdata/qemuxml2argv-sound-device.args,
tests/qemuxml2argvdata/qemuxml2argv-watchdog-device.args: Update
to include PCI slot/bus information
QEMU always configures a VGA card. If no video card is included in
the libvirt XML, it is neccessary to explicitly turn off the default
using -vga none
* src/qemu/qemu_conf.c: Pass -vga none if no video card is configured
* tests/qemuargv2xmltest.c, tests/qemuxml2argvtest.c: Test for
handling -vga none.
* tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.args,
tests/qemuxml2argvdata/qemuxml2argv-nographics-vga.xml: Test
data files
Not all QEMU builds default to SDL graphics for their display.
Newer QEMU now has an explicit -sdl flag, which we can use to
explicitly request SDL intead of relying on the default. This
protects libvirt against unexpected changes in graphics default
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Probe for -sdl
flag and use it if it is found
* tests/qemuhelptest.c: Add SDL flag to tests
The old syntax was
-chardev SOMECONFIG
-nic user,guestfwd=tcp:IP:PORT-chardev:CHARDEV
The new syntax is
-chardev SOMECONFIG
-netdev user,guestfwd=tcp:IP:PORT,chardev=ID,id=user-ID
The old syntax was
-usbdevice host:PRODUCT:VENDOR
Or
-usbdevice host:BUS.DEV
The new syntax is
-device usb-host,product=PRODUCT,vendor=VENDOR
Or
-device usb-host,hostbus=BUS,hostaddr=DEV
The previous syntax was severely limited in its options
-usbdevice disk:/home/berrange/output.img
The new syntax is the same as for other disk types
-drive file=/home/berrange/output.img,if=none,id=usb-1,index=1
-device usb-storage,drive=usb-1
Again, the index= arg is wrong here, and will be removed in a
later merge
The current syntax uses a pair of args
-net nic,macaddr=52:54:00:56:6c:55,vlan=3,model=pcnet,name=pcnet.0
-net user,vlan=3,name=user.0
The new syntax does not need the vlan craziness anymore, and
so has a simplified pair of args
-netdev user,id=user.0
-device pcnet,netdev=user.0,id=pcnet.0,mac=52:54:00:56:6c:55,addr=<PCI SLOT>
The current syntax for audio devices is a horrible multiplexed
arg
-soundhw sb16,pcspk,ac97
The new syntax is
-device sb16,id=sound0
or
-device AC97,id=sound1,addr=<PCI SLOT>
NB, pcspk still uses the old -soundhw syntax
The current character device syntax uses either
-serial tty,path=/dev/ttyS2
Or
-chardev tty,id=serial0,path=/dev/ttyS2 -serial chardev:serial0
With the new -device support, we now prefer
-chardev file,id=serial0,path=/tmp/serial.log -device isa-serial,chardev=serial0
This patch changes the existing -chardev syntax to use this new
scheme, and fallbacks to the old plain -serial syntax for old
QEMU.
The monitor device changes to
-chardev socket,id=monitor,path=/tmp/test-monitor,server,nowait -mon chardev=monitor
In addition, this patch adds --nodefaults, which kills off the
default serial, parallel, vga and nic devices. THis avoids the
need for us to explicitly turn each off
Probe for the new -device flag and if available set the -nodefaults
flag, instead of using -net none, -serial none or -parallel none.
Other device types will be converted to use -device in later patches.
The -nodefaults flag will help avoid unwelcome surprises from future
QEMU releases
* src/qemu/qemu_conf.c: Probe for -device. Add -nodefaults flag.
Remove -net none, -serial none or -parallel none
* src/qemu/qemu_conf.h: Define QEMU_CMD_FLAG_DEVICE
* tests/qemuhelpdata/qemu-0.12.1: New data file for 0.12.1 QEMU
* tests/qemuhelptest.c: Test feature extraction from 0.12.1 QEMU
Existing applications using libvirt are not aware of the disk
controller concept. Thus, after parsing the <disk> definitions
in the XML, it is neccessary to create <controller> elements
to satisfy all requested disks, as per their defined drive
addresses
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/libvirt_private.syms: Add virDomainDefAddDiskControllers()
method for populating disk controllers, and call it after
parsing disk definitions.
* src/qemu/qemu_conf.c: Call virDomainDefAddDiskControllers()
when doing ARGV -> XML conversion
* tests/qemuxml2argvdata/qemuxml2argv*.xml: Add disk controller
data to all data files which don't have it already
It is perfectly acceptable to have multiple sound devices of
same type in guest configuration. If the underlying hypervisor
does not like this, it is its job to complain, not the XML
parser's
* src/conf/domain_conf.c: Remove hack which deleted duplicated
sound device models.
* tests/xml2sexprdata/xml2sexpr-fv-sound.xml: Remove duplicate
models
The latter is not officially "wrong", but *is* terribly anachronistic.
I think automake documentation or comments call that syntax obsolescent.
* cfg.mk (_makefile_at_at_check_exceptions): Exempt @SCHEMADIR@
and @SYSCONFDIR@ uses -- there are no Makefile variables for those.
* docs/Makefile.am: Use $(INSTALL), not @INSTALL@.
* examples/dominfo/Makefile.am: Similar.
* examples/domsuspend/Makefile.am: Similar.
* proxy/Makefile.am: Similar.
* python/Makefile.am: Similar.
* python/tests/Makefile.am: Similar.
* src/Makefile.am: Similar.
* tests/Makefile.am: Similar.
* src/conf/domain_conf.c: add defaults for the video device
* src/esx/esx_vmx.[ch]: add VNC support to the VMX handling
* tests/vmx2xmltest.c, tests/xml2vmxtest.c: add tests for the VNC support
The current code for using -drive simply sets the -drive 'index'
parameter. QEMU internally converts this to bus/unit depending
on the type of drive. This does not give us precise control over
the bus/unit assignment though. This change switches over to make
libvirt explicitly calculate the bus/unit number.
In addition bus/unit/index are actually irrelevant for VirtIO
disks, since each virtio disk is a separate PCI device. No disk
controller is involved.
Doing the conversion to bus/unit in libvirt allows us to correctly
attach SCSI controllers when required.
* src/qemu/qemu_conf.c: Specify bus/unit instead of index for
disks
* tests/qemuxml2argvdata/qemuxml2argv-disk*.args: Switch over from
using index=NNNN, to bus=NN, unit=NN for SCSI/IDE/Floppy disks
When parsing the <disk> element specification, if no <address>
is provided for the disk, then automatically assign one based on
the <target dev='sdXX'/> device name. This provides for backwards
compatability with existing applications using libvirt, while also
allowing new apps to have complete fine grained control.
* src/conf/domain_conf.h, src/conf/domain_conf.c,
src/libvirt_private.syms: Add virDomainDiskDefAssignAddress()
for assigning a controller/bus/unit address based on disk target
* src/qemu/qemu_conf.c: Call virDomainDiskDefAssignAddress() after
generating XML from ARGV
* tests/qemuxml2argvdata/*.xml: Add in drive address information
to all XML files
Only print out '.' for each test case, full test output can be
re-enabled with VIR_TEST_VERBOSE=1, or VIR_TEST_DEBUG=XXXX
Sample output now looks like
TEST: statstest
........................................ 40
................................... 75 OK
PASS: statstest
TEST: qparamtest
................................ 32 OK
PASS: qparamtest
TEST:
............ 12 OK
The MAC addresses with 00:50:56 prefix are split into several ranges:
00:50:56:00:00:00 - 00:50:56:3f:ff:ff 'static' range (manually assigned)
00:50:56:80:00:00 - 00:50:56:bf:ff:ff 'vpx' range (assigned by a VI Client)
Erroneously the 'vpx' range was assumed to be larger and to occupy the
remaining addresses of the 00:50:56 prefix that are not part of the 'static'
range.
00:50:56 was used as prefix for generated MAC addresses, this is not possible
anymore, because there are gaps in the allowed ranges. Therefore, change the
prefix to 00:0c:29 which is the prefix for auto generated MAC addresses anyway.
Allow arbitrary MAC addresses to be used and set the checkMACAddress VMX option
to false in case the MAC address doesn't fall into any predefined range.
* docs/drvesx.html.in: update website accordingly
* src/esx/esx_driver.c: set the auto generation prefix to 00:0c:29
* src/esx/esx_vmx.c: fix MAC address range handling and allow arbitrary MAC
addresses
* tests/vmx2xml*, tests/xml2vmx*: add some basic MAC address range tests
The behavior for the qemu balloon device has changed. Formerly, a virtio
balloon device was provided by default. Now, '-balloon virtio' must be
specified on the command line to enable it. This patch causes libvirt to
add '-balloon virtio' to the command line whenever the -balloon option is
available.
* src/qemu/qemu_conf.c src/qemu/qemu_conf.h: check for the new flag and
add "-baloon vitio" to qemu command when needed
* tests/qemuhelptest.c: add the new flag for detection
tests/virt-aa-helper-test and examples/apparmor are not included in
official tarballs, but should be. Attached is a patch to fix that
which works when apparmor is and is not available.
Change -monitor, -serial and -parallel output to use -chardev if it is
available.
* src/qemu/qemu_conf.c: Update qemudBuildCommandLine to use -chardev where
available.
* tests/qemuxml2argvtest.c tests/qemuxml2argvdata/: Add -chardev equivalents
for all current serial and parallel tests.
Initial support for the new QEMU monitor protocol using JSON
as the data encoding format instead of plain text
* po/POTFILES.in: Add src/qemu/qemu_monitor_json.c
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h: Hack to turn on QMP
mode. Replace with a version number check on >= 0.12 later
* src/qemu/qemu_monitor.c: Delegate to json monitor if enabled
* src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h: Add
impl of QMP protocol
* src/Makefile.am: Add src/qemu/qemu_monitor_json.{c,h}
esxVMX_IndexToDiskName handles indices up to 701. This limit comes
from a mapping gap in virDiskNameToIndex:
sdzy -> 700
sdzz -> 701
sdaaa -> 728
sdaab -> 729
This line in virDiskNameToIndex causes this gap:
idx = (idx + i) * 26;
Fixing it by altering this line to:
idx = (idx + (i < 1 ? 0 : 1)) * 26;
Also add a new version of virIndexToDiskName that handles the inverse
mapping for arbitrary indices.
* src/esx/esx_vmx.[ch]: remove esxVMX_IndexToDiskName
* src/util/util.[ch]: add virIndexToDiskName and fix mapping gap
* tests/esxutilstest.c: update test to verify that the gap is fixed
Introduce a new type="dir" mode for <disks> that allows use of
QEMU's virtual FAT block device driver. eg
<disk type='dir' device='floppy'>
<source dir='/tmp/test'/>
<target dev='fda' bus='fdc'/>
<readonly/>
</disk>
gets turned into
-drive file=fat:floppy:/tmp/test,if=floppy,index=0
Only read-only disks are supported with virtual FAT mode
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add type="dir"
* docs/schemas/domain.rng: Document new disk type
* src/xen/xend_internal.c, src/xen/xm_internal.c: Raise error for
unsupported disk types
* tests/qemuxml2argvdata/qemuxml2argv-disk-cdrom-empty.args: Fix
empty disk file handling
* tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-disk-drive-fat.xml,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.args,
tests/qemuxml2argvdata/qemuxml2argv-floppy-drive-fat.xml
tests/qemuxml2argvtest.c: Test QEMU vitual FAT driver
* src/qemu/qemu_conf.c: Support generating fat:/some/dir type
disk args
* src/security/security_selinux.c: Temporarily skip labelling
of directory based disks
Recent qemu releases require command option '-enable-qemu' in order
for the kvm functionality be activated. Libvirt needs to pass this flag
to qemu when starting a domain. Note that without the option,
even if both the kernel and qemu support KVM, KVM will not be activated
and VMs will be very slow.
* src/qemu/qemu_conf.h src/qemu/qemu_conf.c: parse the extra command
line option from help and add it when running kvm
* tests/qemuhelptest.c: this modified the flags output for qemu-0.10.5
and qemu-kvm-0.11.0-rc2 regression tests
VMware uses two MAC address prefixes: 00:0c:29 and 00:50:56. The 00:0c:29
prefix is used for ESX server generated addresses. The 00:50:56 prefix is
split into two parts. MAC addresses above 00:50:56:3f:ff:ff are generated
by a vCenter. The rest of the 00:50:56 prefix can be assigned manually.
Any MAC address within the 00:0c:29 and 00:50:56 prefix can be specified
in a domain XML config and the driver will handle the details internally.
* src/esx/esx_vmx.c: fix MAC address formatting
* tests/xml2vmxdata/*: update test files accordingly
* src/security/virt-aa-helper.c: get_definition() now calls the new
caps_mockup() function which will parse the XML for os.type,
os.type.arch and then sets the wordsize. These attributes are needed
only to get a valid virCapsPtr for virDomainDefParseString(). The -H
and -b options are now removed from virt-aa-helper (they weren't used
yet anyway).
* tests/virt-aa-helper-test: extend and fixes tests, chmod'ed 755
allows the following to be specified in a domain:
<channel type='pipe'>
<source path='/tmp/guestfwd'/>
<target type='guestfwd' address='10.0.2.1' port='4600'/>
</channel>
* proxy/Makefile.am: add network.c as dep of domain_conf.c
* docs/schemas/domain.rng src/conf/domain_conf.[ch]: extend the domain
schemas and the parsing/serialization side for the new construct
QEmu support will add the following on the qemu command line:
-chardev pipe,id=channel0,path=/tmp/guestfwd
-net user,guestfwd=tcp:10.0.2.1:4600-chardev:channel0
* src/qemu/qemu_conf.c: Add argument output for channel
* tests/qemuxml2(argv|xml)test.c: Add test for <channel> domain syntax
- Don't duplicate SystemError
- Use proper error code in domain_conf
- Fix a broken error call in qemu_conf
- Don't use VIR_ERR_ERROR in security driver (isn't a valid code in this case)
