Commit Graph

19 Commits

Author SHA1 Message Date
Daniel P. Berrange
27cd763500 Increase default file handle limits for daemons
Linux still defaults to a 1024 open file handle limit. This causes
scalability problems for libvirtd / virtlockd / virtlogd on large
hosts which might want > 1024 guest to be running. In fact if each
guest needs > 1 FD, we can't even get to 500 guests. This is not
good enough when we see machines with 100's of physical cores and
TBs of RAM.

In comparison to other memory requirements of libvirtd & related
daemons, the resource usage associated with open file handles
is essentially line noise. It is thus reasonable to increase the
limits unconditionally for all installs.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2017-03-16 10:48:09 +00:00
Daniel P. Berrange
aed0850e39 virtlockd: fix systemd unit file dependancies
After deploying virtlogd by default we identified a number of
mistakes in the systemd unit file. virtlockd's relationship
to libvirtd is the same as virtlogd, so we must apply the
same unit file fixes to virtlockd

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2017-02-03 16:40:08 +00:00
Andrea Bolognani
839a060890 virtlogd.socket: Tie lifecycle to libvirtd.service
We already guarantee that virtlogd.socket is enabled/disabled
along with libvirtd.service, but if libvirtd.service has just
been installed and is started before rebooting, then
virtlogd.socket will not be running and guest startup will
fail.

Add Requires=virtlogd.socket to libvirtd.service to make sure
virtlogd.socket is always started along with libvirtd.service,
and add Before=libvirtd.service to both virtlogd.socket and
virtlogd.service so that virtlogd never disappears before
libvirtd has exited.

Also add PartOf=libvirtd.service to both virtlogd.socket and
virtlogd.service, so that virtlogd can be shut down when not
needed.

Resolves: https://bugzilla.redhat.com/1372576
2016-09-06 16:05:20 +02:00
Cole Robinson
3b9100a4d2 Revert "daemon: use socket activation with systemd"
This reverts commit 1e9808d3a1.

We shouldn't advertise libvirtd.socket activation, since currently
it means VM/network/... autostart won't work as expected.

We tried to find a middle ground by installing the config file without
an [Install] section, since systemd won't allow .socket to be enabled
without one... or at least it did do that; presently on f24 it allows
activating the socket quite happily. This also caused user confusion[1]

Just remove the socket file. I've filed a new RFE to track coming up
with a solution to the autostart problem[2], we can point users at that
if there's more confusion:

[1]: https://bugzilla.redhat.com/show_bug.cgi?id=1279348
[2]: https://bugzilla.redhat.com/show_bug.cgi?id=1326136
2016-04-20 08:53:38 -04:00
Daniel P. Berrange
5cce775e92 libvirtd: enable virtlockd/virtlogd socket activation on install
When someone does 'systemctl enable libvirtd.service' we should
also enable virtlockd.socket/virtlogd.socket, so that they can
be auto-activated if libvirtd tries to access the sockets.

Without this, people have to manually enable the units themselves
via 'systemctl enable virtdlogd.socket'.

This also ensures that if distros uses  'systemctl preset' for
enabling 'libvirtd.service', then the virtdlogd.socket gets
enabled without having to wait for the distro to update their
presets file.

Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2015-12-07 17:32:49 +00:00
Martin Kletzander
3418e7815a Start daemon only after filesystems are mounted
When images are on mounted filesystems, there is no guarantee libvirtd
will start before they are mounted.  Since we want to start after both
local and remote filesystems are mounted, we need to add both local-fs
and remote-fs as targets that should precede starting libvirtd service.

Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
2015-08-26 16:27:49 +02:00
Martin Kletzander
1e9808d3a1 daemon: use socket activation with systemd
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
2014-08-22 09:12:14 +02:00
Cédric Bosdonnat
a3e4eeff52 Make sure apparmor is started before libvirtd
If apparmor security driver is enabled in either qemu or lxc
driver configuration and libvirtd starts before AppArmor, it will fail.
2014-03-04 11:07:05 +00:00
Michal Privoznik
68954fb25c virNetServerRun: Notify systemd that we're accepting clients
Systemd does not forget about the cases, where client service needs to
wait for daemon service to initialize and start accepting new clients.
Setting a dependency in client is not enough as systemd doesn't know
when the daemon has initialized itself and started accepting new
clients. However, it offers a mechanism to solve this. The daemon needs
to call a special systemd function by which the daemon tells "I'm ready
to accept new clients". This is exactly what we need with
libvirtd-guests (client) and libvirtd (daemon). So now, with this
change, libvirt-guests.service is invoked not any sooner than
libvirtd.service calls the systemd notify function.

Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
2014-02-24 10:54:48 +01:00
Guido Günther
1b9f5aa7fe Add Documentation fields to systemd service files
We point to the manpages where available and redirect to libvirt's
homepage as a last resort.
2014-01-09 09:32:55 +01:00
Mooli Tayer
6f4a0ebe8c Configuring systemd to restart libvirt on failure
This will create a respawn behaviour in case libvirt
process exits due to nonzero exit code, is terminated
by a signal, an operation times out or the configured
watchdog timeout is triggered.
see http://www.freedesktop.org/software/systemd/man/systemd.service.html
and https://bugzilla.redhat.com/show_bug.cgi?id=981974

Signed-off-by: Eric Blake <eblake@redhat.com>
2013-07-31 16:55:27 -06:00
Fritz Elfert
443ec5c8c3 libvirt does not logout of iscsi targets, causing system hang on shutdown
There's a quite old bug entry here:

https://bugzilla.redhat.com/show_bug.cgi?id=700010

I just stumbled over that very issue on F18. Doing a little bit
debugging of the shutdown sequence, it turns out that - at least on my
F18 installation - libvirtd is shutdown *after* iscsid, which makes it
impossible for libvirt to perform the logout of the iscsi session properly.

This patch simply adds another startup dependancy on iscsid.service
which in turn delays iscsid shutdown until after libvirtd has stopped.
Having that applied, the system shuts down properly again.

Signed-off-by: Eric Blake <eblake@redhat.com>
2013-03-04 06:28:57 -07:00
Eric Blake
c748037f2a systemd: require dbus service
https://bugzilla.redhat.com/show_bug.cgi?id=830201

The initscript and upstart services depend on dbus starting
before libvirtd.  When we first wrote the systemd script, we
tried to do the same, but we depended on dbus.target (which
does not exist) in comparison to network.target (which does
exist), so we removed that in commit 4c7973e.  But we still
need dbus up and running first, especially now that we want
to support shutdown inhibition via dbus (whereas we originally
needed dbus only for firewall control).

http://www.freedesktop.org/software/systemd/man/systemd.target.html
explains how a target (such as network.target) is just a collection
of common services bundled together, and why we want network.target
but dbus.service.

* daemon/libvirtd.service.in (Unit): Depend on dbus starting
first.
2012-12-05 16:13:07 +08:00
Jim Fehlig
4036aa91bf systemd: start libvirtd after network
Domains configured with autostart may fail to start if the host
network stack has not been started.  E.g. when using bridged
networking autostarting a domain can fail with

libvirtd[1403]: 2012-06-20 13:23:49.833+0000: 1485: error :
qemuAutostartDomain:177 : Failed to autostart VM 'test': Cannot get
interface MTU on 'br0': No such device
2012-07-10 08:53:40 -06:00
Daniel P. Berrange
4c7973e184 Remove more bogus systemd service dependencies
Adding syslog.target is obsolete, avahi.target does not
exist and dbus.target is also obsolete

Reported-by: Lennart Poettering <lpoetter@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2012-05-23 12:03:06 +01:00
Daniel P. Berrange
6cfc3f8f4f Remove bogus udev.target dep from libvirtd unit
There is no 'udev.target' unit in systemd (only 'udev.service')
yet libvirtd's unit file had a dep on one. There's no compelling
reason for a dep on udev, so remove it altogether.

Reported-by: Avi Kivity <avi@redhat.com>
2012-05-16 10:04:59 +01:00
Daniel P. Berrange
cb640543c8 Leave all child processes running when stopping systemd service
Currently the libvirt.service unit file for systemd does not
specify any kill mode. So systemd kills off every process
inside its cgroup. ie all dnsmasq processes, all virtual
machines. This obviously not what we want. Set KillMode=process
so that it only kills the top level process of libvirtd

* daemon/libvirtd.service.in: Add KillMode=process

Reported-By: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
2012-03-23 12:46:16 +00:00
Michal Privoznik
d7320e799f daemon: Allow overriding NOFILES ulimit for the daemon as well
One of my latest patches (d8db0f9690) created support for setting
the limit for the maximum of opened files by qemu user. However,
since libvirtd keeps one FD opened per domain (well, for qemu at least)
it will likely hit this limit on huge scenarios.
2012-02-01 16:04:30 +01:00
Daniel P. Berrange
4789fb2e4e Add support for systemd init service
This patch adds support for a systemd init service for libvirtd
and libvirt-guests. The libvirtd.service is *not* written to use
socket activation, since we want libvirtd to start on boot so it
can do guest auto-start.

The libvirt-guests.service is pretty lame, just exec'ing the
original init script for now. Ideally we would factor out the
functionality, into some shared tool.

Instead of

  ./configure --with-init-script=redhat

You can now do

  ./configure --with-init-script=systemd

Or better still:

  ./configure --with-init-script=systemd+redhat

We can also now support install of the upstart init script

* configure.ac: Add systemd, and systemd+redhat options to
  --with-init-script option
* daemon/Makefile.am: Install systemd services
* daemon/libvirtd.sysconf: Add note about unused env variable
  with systemd
* daemon/libvirtd.service.in: libvirtd systemd service unit
* libvirt.spec.in: Add scripts to installing systemd services
  and migrating from legacy init scripts
* tools/Makefile.am: Install systemd services
* tools/libvirt-guests.init.sh: Rename to tools/libvirt-guests.init.in
* tools/libvirt-guests.service.in: systemd service unit
2011-11-18 16:16:02 +00:00