Commits 905629f4 and 1716e7a6 have added support for specifying
an IPv4 range and a port range to be used by NAT:
<forward mode='nat'>
<nat>
<address start='10.20.30.40' end='10.20.30.44'/>
<port start='60000' end='65432'/>
</nat>
</forward>
https://bugzilla.redhat.com/show_bug.cgi?id=1004364
This patch adds functionality to allow libvirt to configure the
'native-tagged' and 'native-untagged' modes on openvswitch networks.
Signed-off-by: Laine Stump <laine@redhat.com>
This is however supported only on domain interfaces with
type='network'. Moreover, target network needs to have at least
inbound QoS set. This is required by hierarchical traffic shaping.
From now on, the required attribute for <inbound/> is either 'average'
(old) or 'floor' (new). This new attribute can be used just for
interfaces type of network (<interface type='network'/>) currently.
The following config elements now support a <vlan> subelements:
within a domain: <interface>, and the <actual> subelement of <interface>
within a network: the toplevel, as well as any <portgroup>
Each vlan element must have one or more <tag id='n'/> subelements. If
there is more than one tag, it is assumed that vlan trunking is being
requested. If trunking is required with only a single tag, the
attribute "trunk='yes'" should be added to the toplevel <vlan>
element.
Some examples:
<interface type='hostdev'/>
<vlan>
<tag id='42'/>
</vlan>
<mac address='52:54:00:12:34:56'/>
...
</interface>
<network>
<name>vlan-net</name>
<vlan trunk='yes'>
<tag id='30'/>
</vlan>
<virtualport type='openvswitch'/>
</network>
<interface type='network'/>
<source network='vlan-net'/>
...
</interface>
<network>
<name>trunk-vlan</name>
<vlan>
<tag id='42'/>
<tag id='43'/>
</vlan>
...
</network>
<network>
<name>multi</name>
...
<portgroup name='production'/>
<vlan>
<tag id='42'/>
</vlan>
</portgroup>
<portgroup name='test'/>
<vlan>
<tag id='666'/>
</vlan>
</portgroup>
</network>
<interface type='network'/>
<source network='multi' portgroup='test'/>
...
</interface>
IMPORTANT NOTE: As of this patch there is no backend support for the
vlan element for *any* network device type. When support is added in
later patches, it will only be for those select network types that
support setting up a vlan on the host side, without the guest's
involvement. (For example, it will be possible to configure a vlan for
a guest connected to an openvswitch bridge, but it won't be possible
to do that for one that is connected to a standard Linux host bridge.)
Until now, all attributes in a <virtualport> parameter list that were
acceptable for a particular type, were also required. There were no
optional attributes.
One of the aims of supporting <virtualport> in libvirt's virtual
networks and portgroups is to allow specifying the group-wide
parameters in the network's virtualport, and merge that with the
interface's virtualport, which will have the instance-specific info
(i.e. the interfaceid or instanceid).
Additionally, the guest's interface XML shouldn't need to know what
type of network connection will be used prior to runtime - it could be
openvswitch, 802.1Qbh, 802.1Qbg, or none of the above - but should
still be able to specify instance-specific info just in case it turns
out to be applicable.
Finally, up to now, the parser for virtualport has always generated a
random instanceid/interfaceid when appropriate, making it impossible
to leave it blank (which is what's required for virtualports within a
network/portprofile definition).
This patch modifies the parser and formatter of the <virtualport>
element in the following ways:
* because most of the attributes in a virNetDevVPortProfile are fixed
size binary data with no reserved values, there is no way to embed a
"this value wasn't specified" sentinel into the existing data. To
solve this problem, the new *_specified fields in the
virNetDevVPortProfile object that were added in a previous patch of
this series are now set when the corresponding attribute is present
during the parse.
* allow parsing/formatting a <virtualport> that has no type set. In
this case, all fields are settable, but all are also optional.
* add a GENERATE_MISSING_DEFAULTS flag to the parser - if this flag is
set and an instanceid/interfaceid is expected but not provided, a
random one will be generated. This was previously the default
behavior, but is now done only for virtualports inside an
<interface> definition, not for those in <network> or <portgroup>.
* add a REQUIRE_ALL_ATTRIBUTES flag to the parser - if this flag is
set the parser will call the new
virNetDevVPortProfileCheckComplete() functions at the end of the
parser to check for any missing attributes (based on type), and
return failure if anything is missing. This used to be default
behavior. Now it is only used for the virtualport defined inside an
interface's <actual> element (by the time you've figured out the
contents of <actual>, you should have all the necessary data to fill
in the entire virtualport)
* add a REQUIRE_TYPE flag to the parser - if this flag is set, the
parser will return an error if the virtualport has no type
attribute. This also was previously the default behavior, but isn't
needed in the case of the virtualport for a type='network' interface
(i.e. the exact type isn't yet known), or the virtualport of a
portgroup (i.e. the portgroup just has modifiers for the network's
virtualport, which *does* require a type) - in those cases, the
check will be done at domain startup, once the final virtualport is
assembled (this is handled in the next patch).
Hi,
this is the fifth version of my SRV record for DNSMasq patch rebased
for the current codebase to the bridge driver and libvirt XML file to
include support for the SRV records in the DNS. The syntax is based on
DNSMasq man page and tests for both xml2xml and xml2argv were added as
well. There are some things written a better way in comparison with
version 4, mainly there's no hack in tests/networkxml2argvtest.c and
also the xPath context is changed to use a simpler query using the
virXPathInt() function relative to the current node.
Also, the patch is also fixing the networkxml2argv test to pass both
checks, i.e. both unit tests and also syntax check.
Please review,
Michal
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Define new 'bandwidth' element with possible child element 'inbound'
and 'outbound' addressing incoming and outgoing traffic respectively:
<bandwidth>
<inbound average='1000' peak='2000' burst='5120'/>
<outbound average='500'/>
</bandwidth>
Leaving any element out means not to shape traffic in that
direction.
The units for average and peak (rate) are in kilobytes per second,
for burst (size) are just in kilobytes.
This element can be inserted into domain's 'interface' and
'network'.
virtPortProfiles are currently only used in the domain XML, but will
soon also be used in the network XML. To prepare for that change, this
patch moves the structure definition into util/network.h and the parse
and format functions into util/network.c (I decided that this was a
better choice than macvtap.h/c for something that needed to always be
available on all platforms).
