When support for <interface type='ethernet'> was added in commit
9a4b705f back in 2010, it erroneously looked at <source dev='blah'/>
for a user-specified guest-side interface name. This was never
documented though. (that attribute already existed at the time in the
data.ethernet union member of virDomainNetDef, but apparently had no
practical use - it was only used as a storage place for a NetDef's
bridge name during qemuDomainXMLToNative(), but even then that was
never used for anything).
When support for similar guest-side device naming was added to the lxc
driver several years later, it was put in a new subelement <guest
dev='blah'/>.
In the intervening years, since there was no validation that
ethernet.dev was NULL in the other drivers that didn't actually use
it, innocent souls who were adding other features assuming they needed
to account for non-NULL ethernet.dev when really they didn't, so
little bits of the usual pointless cargo-cult code showed up.
This patch not only switches the openvz driver to use the documented
<guest dev='blah'/> notation for naming the guest-side device (just in
case anyone is still using the openvz driver), and logs an error if
anyone tries to set <source dev='blah'/> for a type='ethernet'
interface, it also removes the cargo-cult uses of ethernet.dev and
<source dev='blah'/>, and eliminates if from the RNG and from
virDomainNetDef.
NB: I decided on this course of action after mentioning the
inconsistency here:
https://www.redhat.com/archives/libvir-list/2016-May/msg02038.html
and getting encouragement do eliminate it in a later IRC discussion
with danpb.
There was no documentation at all for the XML part. I added at least
some. The 2.0.0 introduction date is deliberate as the parser for the
XML is broken.
The schema file was missing entries for 'mbml' and 'mbmt'.
This option allows or disallows detection of zero-writes if it is set to
"on" or "off", respectively. It can be also set to "unmap" in which
case it will try discarding that part of image based on the value of the
"discard" option.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This new listen type is currently supported only by spice graphics.
It's introduced to make it easier and clearer specify to not listen
anywhere in order to start a guest with OpenGL support.
The old way to do this was set spice graphics autoport='no' and don't
specify any ports. The new way is to use <listen type='none'/>. In
order to be able to migrate to old libvirt the migratable XML will be
generated without the listen element and with autoport='no'. Also the
old configuration will be automatically converted to the this listen
type.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Hand-entering indexes for 20 PCI controllers is not as tedious as
manually determining and entering their PCI addresses, but it's still
annoying, and the algorithm for determining the proper index is
incredibly simple (in all cases except one) - just pick the lowest
unused index.
The one exception is USB2 controllers because multiple controllers in
the same group have the same index. For these we look to see if 1) the
most recently added USB controller is also a USB2 controller, and 2)
the group *that* controller belongs to doesn't yet have a controller
of the exact model we're just now adding - if both are true, the new
controller gets the same index, but in all other cases we just assign
the lowest unused index.
With this patch in place and combined with the automatic PCI address
assignment, we can define a PCIe switch with several ports like this:
<controller type='pci' model='pcie-root-port'/>
<controller type='pci' model='pcie-switch-upstream-port'/>
<controller type='pci' model='pcie-switch-downstream-port'/>
<controller type='pci' model='pcie-switch-downstream-port'/>
<controller type='pci' model='pcie-switch-downstream-port'/>
<controller type='pci' model='pcie-switch-downstream-port'/>
<controller type='pci' model='pcie-switch-downstream-port'/>
...
These will each get a unique index, and PCI addresses that connect
them together appropriately with no pesky numbers required.
Add a new element to <domain> XML:
<os>
<acpi>
<table type="slic">/path/to/acpi/table/file</table>
</acpi>
</os>
To supply a path to a SLIC (Software Licensing) ACPI
table blob.
https://bugzilla.redhat.com/show_bug.cgi?id=1327537
Prior to this, <address type='pci'/> wasn't allowed when parsing
(domain+bus+slot+function needed to be a "valid" PCI address, meaning
that at least one of domain/bus/slot had to be non-0), the RNG
required bus to be specified, and if type was set to PCI when
formatting, domain+bus+slot+function would always be output.
This makes all the address attributes optional during parse and RNG
validation, and suppresses domain+bus+slot+function if domain+bus+slot
are all 0 (NB: if d+b+s are all 0, any value for function is
nonsensical as that will never happen in the real world, and after
the next patch we will always assign a real working address to any
empty PCI address before it is ever output to anywhere).
Note that explicitly setting all attributes to 0 is equivalent to
setting none of them, which is okay, since 0000:00:00 is reserved in
any PCI bus setup, and can't be used anyway.
We support omitting listen attribute of graphics element so we should
also support omitting address attribute of listen element. This patch
also updates libvirt to always add a listen element into domain XML
except for VNC graphics if socket attribute is specified.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Requires adding the plumbing for <device><video>
The value is <enum name='modelType'> to match the associated domain
XML of <video><model type='XXX'/>
Wire it up for qemu too
Add the ability to add an 'iothread' to the controller which will be how
virtio-scsi-pci and virtio-scsi-ccw iothreads have been implemented in qemu.
Describe the new functionality and add tests to parse/validate that the
new attribute can be added.
This adds a ports= attribute to usb controller XML, like
<controller type='usb' model='nec-xhci' ports='8'/>
This maps to:
qemu -device nec-usb-xhci,p2=8,p3=8
Meaning, 8 ports that support both usb2 and usb3 devices. Gerd
suggested to just expose them as one knob.
https://bugzilla.redhat.com/show_bug.cgi?id=1271408
If a panic device is being defined without a model in a domain
the default value is always overwritten with model ISA. An ISA
bus does not exist on S390 and therefore specifying a panic device
results in an unsupported configuration.
Since the S390 architecture inherently provides a crash detection
capability the panic device should be defined in the domain xml.
This patch adds an s390 panic device model and prevents setting a
device address on it.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
There were few things done in the nodedev code but we were lacking tests
for it. And because of that we missed that the schema was not updated
either. Fix the schema and add various test files to show the schema
is correct.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This reverts commit 690969af9c, which
added the domain config parts to support a "peer" attribute in domain
interface <ip> elements.
It's being removed temporarily for the release of libvirt 1.3.4
because the feature doesn't work, and there are concerns that it may
need to be modified in an externally visible manner which could create
backward compatibility problems.
Currently we only allow /dev/random and /dev/hwrng as host input
for <rng><backend model='random'/> device. This was added after
various upstream discussions in commit 4932ef45
However this restriction has generated quite a few complaints over
the years, so a new discussion was initiated:
http://www.redhat.com/archives/libvir-list/2016-April/msg00987.html
Several people suggested removing the restriction, and nobody really
spoke up to defend it. So this patch drops the path restriction
entirely
https://bugzilla.redhat.com/show_bug.cgi?id=1074464
This controller provides a single PCIe port on a new root. It is
similar to pci-expander-bus, intended to provide a bus that can be
associated with a guest-identifiable NUMA node, but is for
machinetypes with PCIe rather than PCI (e.g. q35-based machinetypes).
Aside from PCIe vs. PCI, the other main difference is that a
pci-expander-bus has a companion pci-bridge that is automatically
attached along with it, but pcie-expander-bus has only a single port,
and that port will only connect to a pcie-root-port, or to a
pcie-switch-upstream-port. In order for the bus to be of any use in
the guest, it must have either a pcie-root-port or a
pcie-switch-upstream-port attached (and one or more
pcie-switch-downstream-ports attached to the
pcie-switch-upstream-port).
This is a standard PCI root bus (not a bridge) that can be added to a
440fx-based domain. Although it uses a PCI slot, this is *not* how it
is connected into the PCI bus hierarchy, but is only used for
control. Each pci-expander-bus provides 32 slots (0-31) that can
accept hotplug of standard PCI devices.
The usefulness of pci-expander-bus relative to a pci-bridge is that
the NUMA node of the bus can be specified with the <node> subelement
of <target>. This gives guest-side visibility to the NUMA node of
attached devices (presuming that management apps only assign a device
to a bus that has a NUMA node number matching the node number of the
device on the host).
Each pci-expander-bus also has a "busNr" attribute. The expander-bus
itself will take the busNr specified, and all buses that are connected
to this bus (including the pci-bridge that is automatically added to
any expander bus of model "pxb" (see the next commit)) will use
busNr+1, busNr+2, etc, and the pci-root (or the expander-bus with next
lower busNr) will use bus numbers lower than busNr.
This is especially useful for "bus", since the bus of a device's pci
address is matched to the "index" of a controller to determine which
bus it will be connected to, and "index" is always specified in
decimal - being able to specify both in decimal at least makes it
easier to assure a device is being assigned to the correct bus when it
is added. For the other attributes, it is just a convenience.
(MB: the parser already allows for any of these attributes to be given
in decimal, and there are even examples floating around on the
internet that give them in decimal rather than hex (written in the
days before virsh did schema validation on all XML). This only updates
the schema to match the parser.)
nwfilter.rng defines uint16range and uint32range, but in a different
manner (it also allows a variable name as the value, rather than just
a decimal or hex number). I wanted to add uint16range to
basictypes.rng, but my desired definition was parallel to those for
uint8range and uint24range which are defined in basictypes.rng - they
*don't* allow a variable name for the value.
The simplest path to make everyone happy is to make the "plain"
versions in basictypes.rng have simpler names - "uint8", "uint16", and
"uint24". This patch renames uint8range and uint24range to uint8 and
uint24, while the next patch will add uint16.
The pcie-switch-downstream-port and pcie-root-port controllers have
only a single slot, numbered 0, and the greate majority of all guest
PCI devices are plugged into function 0 of whatever slot they're
using. The parser makes these optional, setting them to 0 when not
specified, and it's logical for the schema to also make them optional.
This patch adds new xml element, and so we can have the option of
also having perf events enabled immediately at startup.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Message-id: 1459171833-26416-6-git-send-email-qiaowei.ren@intel.com
This patch adds support for "vpindex", "runtime", "synic",
"stimer", and "vendor_id" features available in qemu 2.5+.
- When Hyper-V "vpindex" is on, guest can use MSR HV_X64_MSR_VP_INDEX
to get virtual processor ID.
- Hyper-V "runtime" enlightement feature allows to use MSR
HV_X64_MSR_VP_RUNTIME to get the time the virtual processor consumes
running guest code, as well as the time the hypervisor spends running
code on behalf of that guest.
- Hyper-V "synic" stands for Synthetic Interrupt Controller, which is
lapic extension controlled via MSRs.
- Hyper-V "stimer" switches on Hyper-V SynIC timers MSR's support.
Guest can setup and use fired by host events (SynIC interrupt and
appropriate timer expiration message) as guest clock events
- Hyper-V "reset" allows guest to reset VM.
- Hyper-V "vendor_id" exposes hypervisor vendor id to guest.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
When reading in an XML definition for a SCSI target device, the name
property of struct scsi_target refers to the @target element.
Let's fix this obvious typo and also extend the XML schema to provide
validation.
Signed-off-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Most hypervisors use Hardware Assisted Paging by default and don't
require specifying the feature in domain conf. But some hypervisors
support disabling HAP on a per-domain basis. To enable HAP by default
yet provide a knob to disable it, extend the <hap> feature with a
'state=on|off' attribute, similar to <pvspinlock> and <vmport> features.
In the absence of <hap>, the hypervisor default (on) is used. <hap>
without the state attribute would be the same as <hap state='on'/> for
backwards compatibility. And of course <hap state='off'/> disables hap.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
If we expose this information, which is one byte in every PCI config
file, we let all mgmt apps know whether the device itself is an endpoint
or not so it's easier for them to decide whether such device can be
passed through into a VM (endpoint) or not (*-bridge).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The docs claims the cache attribute of the disk <driver>
element supports 'default' as one of its permissible values,
but such configuration fails virt-xml-validate. Add 'default'
as one of the cache attribute choices in domaincommon.rng.
Extend the chardev source XML so that there is a new optional
<log/> element, which is applicable to all character device
backend types. For example, to log output of a TCP backed
serial port
<serial type='tcp'>
<source mode='connect' host='127.0.0.1' service='9999'/>
<protocol type='raw'/>
<log file='/var/log/libvirt/qemu/demo-serial0.log' append='on'/>
<target port='0'/>
</serial>
Not all hypervisors will support use of logfiles.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This parameter represents top level period cgroup
that limits whole domain enforcement period for a quota
Signed-off-by: Alexander Burluka <aburluka@virtuozzo.com>
This attribute is used to extend secondary PCI bar and expose it to the
guest as 64bit memory. It works like this: attribute vram is there to
set size of secondary PCI bar and guest sees it as 32bit memory,
attribute vram64 can extend this secondary PCI bar. If both attributes
are used, guest sees two memory bars, both address the same memory, with
the difference that the 32bit bar can address only the first part of the
whole memory.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1260749
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Add Spice graphics gl attribute. qemu 2.6 should have -spice gl=on argument to
enable opengl rendering context (patches on the ML). This is necessary to
actually enable virgl rendering.
Add a qemuxml2argv test for virtio-gpu + spice with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This change allows to use "host" as a GIC version in the domain XML.
Since we'll need to update the virGICVersion enumeration to support
new GIC versions anyway, it makes sense to be a bit more strict in
the schema as well and reject values that are not in the enumeration.
Add a new storage pool source device attribute 'part_separator=[yes|no]'
in order to allow a 'disk' storage pool using a device mapper multipath
device to not add the "p" partition separator to the generated device
name when libvirt_parthelper is run.
This will allow libvirt to find device mapper multipath devices which were
configured in /etc/multipath.conf to use 'user_friendly_names' or custom
'alias' names for the LUN.
Excessive memory balloon inflation can cause invocation of OOM-killer,
when Linux is under severe memory pressure. QEMU memballoon device
has a feature to release some memory at the last moment before some
process will be get killed by OOM-killer.
Introduce a new optional balloon device attribute 'autodeflate' to
enable or disable this feature.
Allow <name> and <uuid> anywhere under <domain>, not just at the top:
error:XML document failed to validate against schema: Unable to validate
doc against /usr/share/libvirt/schemas/domain.rng
Expecting an element name, got nothing
Invalid sequence in interleave
Element domain failed to validate content
Introduced with the first RelaxNG schema in commit c642103.
https://bugzilla.redhat.com/show_bug.cgi?id=1292131
Currently, there is no possibility for user to specify desired behaviour of
output to file - truncate or append. This patch adds an ability to explicitly
specify that user wants to preserve file's content on reopen.
Signed-off-by: Dmitry Mishin <dim@virtuozzo.com>
Using more than 4TiB of memory per NUMA node would not be possible to
express in the XML without violating the schema. Not that such boxes
would be common, but we should use a longer type at this point.
The pattern is not necessary since libvirt redefines the type already in
basictypes.rng with the same pattern.
To be used by the family of virtio input devices:
<input type='mouse' bus='virtio'/>
<input type='tablet' bus='virtio'/>
<input type='keyboard' bus='virtio'/>
https://bugzilla.redhat.com/show_bug.cgi?id=1231114
qemu 2.5 provides virtio video device. It can be used with -device
virtio-vga for primary devices, or -device virtio-gpu for non-vga
devices. However, only the primary device (VGA) is supported with this
patch.
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=1195176
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>