Curently security labels can be of type 'dynamic' or 'static'.
If no security label is given, then 'dynamic' is assumed. The
current code takes advantage of this default, and avoids even
saving <seclabel> elements with type='dynamic' to disk. This
means if you temporarily change security driver, the guests
can all still start.
With the introduction of sVirt to LXC though, there needs to be
a new default of 'none' to allow unconfined LXC containers.
This patch introduces two new security label types
- default: the host configuration decides whether to run the
guest with type 'none' or 'dynamic' at guest start
- none: the guest will run unconfined by security policy
The 'none' label type will obviously be undesirable for some
deployments, so a new qemu.conf option allows a host admin to
mandate confined guests. It is also possible to turn off default
confinement
security_default_confined = 1|0 (default == 1)
security_require_confined = 1|0 (default == 0)
* src/conf/domain_conf.c, src/conf/domain_conf.h: Add new
seclabel types
* src/security/security_manager.c, src/security/security_manager.h:
Set default sec label types
* src/security/security_selinux.c: Handle 'none' seclabel type
* src/qemu/qemu.conf, src/qemu/qemu_conf.c, src/qemu/qemu_conf.h,
src/qemu/libvirtd_qemu.aug: New security config options
* src/qemu/qemu_driver.c: Tell security driver about default
config
The storage pools page contains details about the capabilities of the
various pool types, but not an overview of how they are intended to be
used. This patch adds some explanation of what pools and volumes can
be used for and why an administrator might want to use them.
libvirt supports 4 different versions of the user-land XenD daemon. When
queried the daemon just returns its generation number, which is hard to
match to the version of the Xen tools.
Replace the magic generation numbers by named enum definitions to
improve code readability.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Qemu is adding the ability to do a partial rebase. That is, given:
base <- intermediate <- current
virDomainBlockPull will produce:
current
but qemu now has the ability to leave base in the chain, to produce:
base <- current
Note that current qemu can only do a forward merge, and only with
the current image as the destination, which is fully described by
this API without flags. But in the future, it may be possible to
enhance this API for additional scenarios by using flags:
Merging the current image back into a previous image (that is,
undoing a live snapshot), could be done by passing base as the
destination and flags with a bit requesting a backward merge.
Merging any other part of the image chain, whether forwards (the
backing image contents are pulled into the newer file) or backwards
(the deltas recorded in the newer file are merged back into the
backing file), could also be done by passing a new flag that says
that base should be treated as an XML snippet rather than an
absolute path name, where the XML could then supply the additional
instructions of which part of the image chain is being merged into
any other part.
* include/libvirt/libvirt.h.in (virDomainBlockRebase): New
declaration.
* src/libvirt.c (virDomainBlockRebase): Implement it.
* src/libvirt_public.syms (LIBVIRT_0.9.10): Export it.
* src/driver.h (virDrvDomainBlockRebase): New driver callback.
* src/rpc/gendispatch.pl (long_legacy): Add exemption.
* docs/apibuild.py (long_legacy_functions): Likewise.
This patch adds a new element <title> to the domain XML. This attribute
can hold a short title defined by the user to ease the identification of
domains. The title may not contain newlines and should be reasonably short.
*docs/formatdomain.html.in
*docs/schemas/domaincommon.rng
- add schema grammar for the new element and documentation
*src/conf/domain_conf.c
*src/conf/domain_conf.h
- add field to hold the new attribute
- add code to parse and create XML with the new attribute
Commit 8a09ee410 tickles a bug in libxml2-2.7.6 on RHEL 6.2,
where libxml2 treats the pattern [^\n] as excluding literal
backslash and n, instead of the intended newline, thus failing
to validate any domain name containing 'n'.
* docs/schemas/domaincommon.rng: Use literal newline instead.
The original doc entry for rawio didn't mention the values it could
have, the default, or the fact that setting it to "yes" for one disk
effectively set it to "yes" for all disks in the domain.
This patch adds a new attribute "rawio" to the "disk" element
of domain XML. Valid values of "rawio" attribute are "yes"
and "no".
rawio='yes' indicates the disk is desirous of CAP_SYS_RAWIO.
If you specify the following XML:
<disk type='block' device='lun' rawio='yes'>
...
</disk>
the domain will be granted CAP_SYS_RAWIO.
(of course, the domain have to be executed with root privilege)
NOTE:
- "rawio" attribute is only valid when device='lun'
- At the moment, any other disks you won't use rawio can use rawio.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
This patch addresses: https://bugzilla.redhat.com/show_bug.cgi?id=781562
Along with the "rombar" option that controls whether or not a boot rom
is made visible to the guest, qemu also has a "romfile" option that
allows specifying a binary file to present as the ROM BIOS of any
emulated or passthrough PCI device. This patch adds support for
specifying romfile to both passthrough PCI devices, and emulated
network devices that attach to the guest's PCI bus (just about
everything other than ne2k_isa).
One example of the usefulness of this option is described in the
bugzilla report: 82576 sriov network adapters don't provide a ROM BIOS
for the cards virtual functions (VF), but an image of such a ROM is
available, and with this ROM visible to the guest, it can PXE boot.
In libvirt's xml, the new option is configured like this:
<hostdev>
...
<rom file='/etc/fake/boot.bin'/>
...
</hostdev
(similarly for <interface>).
When support for the rombar option was added, it was only added for
PCI passthrough devices, configured with <hostdev>. The same option is
available for any network device that is attached to the guest's PCI
bus. This patch allows setting rombar for any PCI network device type.
After adding cases to test this to qemuxml2argv-hostdev-pci-rombar.*,
I decided to rename those files (to qemuxml2argv-pci-rom.*) to more
accurately reflect the additional tests, and also noticed that up to
now we've only been performing a domainschematest for that case, so I
added the "pci-rom" test to both qemuxml2argv and qemuxml2xml (and in
the process found some bugs whose fixes I squashed into previous
commits of this series).
Add kvmclock timer to documentation, schema and parsers. Keep the
platform timer first since it is kind of special, and alphabetize
the others when possible (i.e. when it does not change the ABI).
Reviewed-by: Jiri Denemark <jdenemar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The domain schema enforced restrictions on the domain name string that
the code doesn't. This patch relaxes the check, leaving the restrictions
on the driver or hypervisor. The only invalid character is a newline.
It's better to group all the metadata together. This is a
cosmetic output change; since the RNG allows interleave, it
doesn't matter where the user stuck it on input, and an XPath
query will find the same information when parsing the output.
* src/conf/domain_conf.c (virDomainDefFormatInternal): Output
metadata earlier.
* docs/formatdomain.html.in: Update documentation.
* tests/domainsnapshotxml2xmlout/metadata.xml: Update test.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-metadata.xml: Likewise.
Applications can now insert custom nodes and hierarchies into domain
configuration XML. Although currently not enforced, applications are
required to use their own namespaces on every custom node they insert,
with only one top-level element per namespace.
There is now a standard QEMU guest agent that can be installed
and given a virtio serial channel
<channel type='unix'>
<source mode='bind' path='/var/lib/libvirt/qemu/f16x86_64.agent'/>
<target type='virtio' name='org.qemu.guest_agent.0'/>
</channel>
The protocol that runs over the guest agent is JSON based and
very similar to the JSON monitor. We can't use exactly the same
code because there are some odd differences in the way messages
and errors are structured. The qemu_agent.c file is based on
a combination and simplification of qemu_monitor.c and
qemu_monitor_json.c
* src/qemu/qemu_agent.c, src/qemu/qemu_agent.h: Support for
talking to the agent for shutdown
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add thread
helpers for talking to the agent
* src/qemu/qemu_process.c: Connect to agent whenever starting
a guest
* src/qemu/qemu_monitor_json.c: Make variable static
This introduces new attribute wrpolicy with only supported
value as immediate. This will be an optional
attribute with no defaults. This helps specify whether
to skip the host page cache.
When wrpolicy is specified, meaning when wrpolicy=immediate
a writeback is explicitly initiated for the dirty pages in
the host page cache as part of the guest file write operation.
Usage:
<filesystem type='mount' accessmode='passthrough'>
<driver type='path' wrpolicy='immediate'/>
<source dir='/export/to/guest'/>
<target dir='mount_tag'/>
</filesystem>
Currently this only works with type='mount' for the QEMU/KVM driver.
Signed-off-by: Deepak C Shetty <deepakcs@linux.vnet.ibm.com>
The mode can be either of "custom" (default), "host-model",
"host-passthrough". The semantics of each mode is described in the
following examples:
- guest CPU is a default model with specified topology:
<cpu>
<topology sockets='1' cores='2' threads='1'/>
</cpu>
- guest CPU matches selected model:
<cpu mode='custom' match='exact'>
<model>core2duo</model>
</cpu>
- guest CPU should be a copy of host CPU as advertised by capabilities
XML (this is a short cut for manually copying host CPU specification
from capabilities to domain XML):
<cpu mode='host-model'/>
In case a hypervisor does not support the exact host model, libvirt
automatically falls back to a closest supported CPU model and
removes/adds features to match host. This behavior can be disabled by
<cpu mode='host-model'>
<model fallback='forbid'/>
</cpu>
- the same as previous returned by virDomainGetXMLDesc with
VIR_DOMAIN_XML_UPDATE_CPU flag:
<cpu mode='host-model' match='exact'>
<model fallback='allow'>Penryn</model> --+
<vendor>Intel</vendor> |
<topology sockets='2' cores='4' threads='1'/> + copied from
<feature policy='require' name='dca'/> | capabilities XML
<feature policy='require' name='xtpr'/> |
... --+
</cpu>
- guest CPU should be exactly the same as host CPU even in the aspects
libvirt doesn't model (such domain cannot be migrated unless both
hosts contain exactly the same CPUs):
<cpu mode='host-passthrough'/>
- the same as previous returned by virDomainGetXMLDesc with
VIR_DOMAIN_XML_UPDATE_CPU flag:
<cpu mode='host-passthrough' match='minimal'>
<model>Penryn</model> --+ copied from caps
<vendor>Intel</vendor> | XML but doesn't
<topology sockets='2' cores='4' threads='1'/> | describe all
<feature policy='require' name='dca'/> | aspects of the
<feature policy='require' name='xtpr'/> | actual guest CPU
... --+
</cpu>
In case a hypervisor doesn't support the exact CPU model requested by a
domain XML, we automatically fallback to a closest CPU model the
hypervisor supports (and make sure we add/remove any additional features
if needed). This patch adds 'fallback' attribute to model element, which
can be used to disable this automatic fallback.
We support <interface> of type "mcast", "server", and "client",
but the RNG schema for them are missed. Attribute "address" is
optional for "server" type. And these 3 types support
<mac address='MAC'/>, too.
Though <alias> is ignored when defining a domain, it can cause
failure if one validates (e.g. virt-xml-validate) the XML dumped
from a running domain. This patch expose it in domain RNG schema
for all the devices which support it.
The "unit" attribute of a drive address is optional in the code, so should
also be in the XML schema.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
KVM will be able to use a PCI SCSI controller even on POWER. Let
the user specify the vSCSI controller by other means than a default.
After this patch, the QEMU driver will actually look at the model
and reject anything but auto, lsilogic and ibmvscsi.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new introduced optional attribute "copy_on_read</code> controls
whether to copy read backing file into the image file. The value can
be either "on" or "off". Copy-on-read avoids accessing the same backing
file sectors repeatedly and is useful when the backing file is over a
slow network. By default copy-on-read is off.
This patch adds documentation about the new 'ways' that users can
access the contents of variables in filters:
- access via index: $TEST[2]
- access via iterators $TEST[@1]
This patch introduces the capability to use a different iterator per
variable.
The currently supported notation of variables in a filtering rule like
<rule action='accept' direction='out'>
<tcp srcipaddr='$A' srcportstart='$B'/>
</rule>
processes the two lists 'A' and 'B' in parallel. This means that A and B
must have the same number of 'N' elements and that 'N' rules will be
instantiated (assuming all tuples from A and B are unique).
In this patch we now introduce the assignment of variables to different
iterators. Therefore a rule like
<rule action='accept' direction='out'>
<tcp srcipaddr='$A[@1]' srcportstart='$B[@2]'/>
</rule>
will now create every combination of elements in A with elements in B since
A has been assigned to an iterator with Id '1' and B has been assigned to an
iterator with Id '2', thus processing their value independently.
The first rule has an equivalent notation of
<rule action='accept' direction='out'>
<tcp srcipaddr='$A[@0]' srcportstart='$B[@0]'/>
</rule>
In the past, generic SCSI commands issued from a guest to a virtio
disk were always passed through to the underlying disk by qemu, and
the kernel would also pass them on.
As a result of CVE-2011-4127 (see:
http://seclists.org/oss-sec/2011/q4/536), qemu now honors its
scsi=on|off device option for virtio-blk-pci (which enables/disables
passthrough of generic SCSI commands), and the kernel will only allow
the commands for physical devices (not for partitions or logical
volumes). The default behavior of qemu is still to allow sending
generic SCSI commands to physical disks that are presented to a guest
as virtio-blk-pci devices, but libvirt prefers to disable those
commands in the standard virtio block devices, enabling it only when
specifically requested (hopefully indicating that the requester
understands what they're asking for). For this purpose, a new libvirt
disk device type (device='lun') has been created.
device='lun' is identical to the default device='disk', except that:
1) It is only allowed if bus='virtio', type='block', and the qemu
version is "new enough" to support it ("new enough" == qemu 0.11 or
better), otherwise the domain will fail to start and a
CONFIG_UNSUPPORTED error will be logged).
2) The option "scsi=on" will be added to the -device arg to allow
SG_IO commands (if device !='lun', "scsi=off" will be added to the
-device arg so that SG_IO commands are specifically forbidden).
Guests which continue to use disk device='disk' (the default) will no
longer be able to use SG_IO commands on the disk; those that have
their disk device changed to device='lun' will still be able to use SG_IO
commands.
*docs/formatdomain.html.in - document the new device attribute value.
*docs/schemas/domaincommon.rng - allow it in the RNG
*tests/* - update the args of several existing tests to add scsi=off, and
add one new test that will test scsi=on.
*src/conf/domain_conf.c - update domain XML parser and formatter
*src/qemu/qemu_(command|driver|hotplug).c - treat
VIR_DOMAIN_DISK_DEVICE_LUN *almost* identically to
VIR_DOMAIN_DISK_DEVICE_DISK, except as indicated above.
Note that no support for this new device value was added to any
hypervisor drivers other than qemu, because it's unclear what it might
mean (if anything) to those drivers.
Hi,
this is the fifth version of my SRV record for DNSMasq patch rebased
for the current codebase to the bridge driver and libvirt XML file to
include support for the SRV records in the DNS. The syntax is based on
DNSMasq man page and tests for both xml2xml and xml2argv were added as
well. There are some things written a better way in comparison with
version 4, mainly there's no hack in tests/networkxml2argvtest.c and
also the xPath context is changed to use a simpler query using the
virXPathInt() function relative to the current node.
Also, the patch is also fixing the networkxml2argv test to pass both
checks, i.e. both unit tests and also syntax check.
Please review,
Michal
Signed-off-by: Michal Novotny <minovotn@redhat.com>
When doing security relabeling, there are cases where a per-file
override might be appropriate. For example, with a static label
and relabeling, it might be appropriate to skip relabeling on a
particular disk, where the backing file lives on NFS that lacks
the ability to track labeling. Or with dynamic labeling, it might
be appropriate to use a custom (non-dynamic) label for a disk
specifically intended to be shared across domains.
The new XML resembles the top-level <seclabel>, but with fewer
options (basically relabel='no', or <label>text</label>):
<domain ...>
...
<devices>
<disk type='file' device='disk'>
<source file='/path/to/image1'>
<seclabel relabel='no'/> <!-- override for just this disk -->
</source>
...
</disk>
<disk type='file' device='disk'>
<source file='/path/to/image1'>
<seclabel relabel='yes'> <!-- override for just this disk -->
<label>system_u:object_r:shared_content_t:s0</label>
</seclabel>
</source>
...
</disk>
...
</devices>
<seclabel type='dynamic' model='selinux'>
<baselabel>text</baselabel> <!-- used for all devices without override -->
</seclabel>
</domain>
This patch only introduces the XML and documentation; future patches
will actually parse and make use of it. The intent is that we can
further extend things as needed, adding a per-device <seclabel> in
more places (such as the source of a console device), and possibly
allowing a <baselabel> instead of <label> for labeling where we want
to reuse the cNNN,cNNN pair of a dynamically labeled domain but a
different base label.
First suggested by Daniel P. Berrange here:
https://www.redhat.com/archives/libvir-list/2011-December/msg00258.html
* docs/schemas/domaincommon.rng (devSeclabel): New define.
(disk): Use it.
* docs/formatdomain.html.in (elementsDisks, seclabel): Document
the new XML.
* tests/qemuxml2argvdata/qemuxml2argv-seclabel-dynamic-override.xml:
New test, to validate RNG.
The RNG for <seclabel> was too strict - if it was present, then it
had to have sub-elements, even if those didn't make sense for the
given attributes. Also, we didn't have any tests of <seclabel>
parsing or XML output.
In this patch, I added more parsing tests than output tests (since
the output populates and/or reorders fields not present in certain
inputs). Making the RNG reliable is a precursor to using <seclabel>
variants in more places in the XML in later patches.
See also:
http://berrange.com/posts/2011/09/29/two-small-improvements-to-svirt-guest-configuration-flexibility-with-kvmlibvirt/
* docs/schemas/domaincommon.rng (seclabel): Tighten rules.
* tests/qemuxml2argvtest.c (mymain): New tests.
* tests/qemuxml2xmltest.c (mymain): Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-seclabel-*.*: New files.
Commit e5a84d74 added a new attribute in the wrong location;
commit c8b9fa74 fixed the missing / at the end but not the extra
/ in the middle.
* docs/formatdomain.html.in (elementsDisks): Fix another typo.
Original patch by Bharata. Updated to use {1,16} in spaprvioReg based
on example from Eric Blake.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Improve the documentation of what forms a valid <address> element,
since these elements appear in numerous devices.
* docs/formatdomain.html.in (elementsAddress): New section.
(elementsControllers, elementsUSB, elementsNICS, elementsInput)
(elementsHub, elementsCharChannel, elementsSound): Refer to it.
In QEMU PPC64 we have a network device called "spapr-vlan". We can specify
this using the existing syntax for network devices, however libvirt
currently rejects "spapr-vlan" in virDomainNetDefParseXML() because of
the "-". Fix the code to accept "-".
* src/conf/domain_conf.c (virDomainNetDefParseXML): Allow '-' in
model name, and be more efficient.
* docs/schemas/domaincommon.rng: Limit valid model names to match code.
Based on a patch by Michael Ellerman.
ppc64 as new arch type and pseries as new machine type are
added under <os> ... </os>.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
This patch is to expose the fabric_name of fc_host class, which
might be useful for users who wants to known which fabric the
(v)HBA connects to.
The patch also adds the missed capabilities' XML schema of scsi_host,
(of course, with fabric_wwn added), and update the documents
(docs/formatnode.html.in)
Enable block I/O throttle for per-disk in XML, as the first
per-disk IO tuning parameter.
Signed-off-by: Lei Li <lilei@linux.vnet.ibm.com>
Signed-off-by: Zhi Yong Wu <wuzhy@linux.vnet.ibm.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
If we ensure that virNodeSuspendGetTargetMask always resets
*bitmask to zero upon failure, there is no need for the
powerMgmt_valid field.
* src/util/virnodesuspend.c: Ensure *bitmask is zero upon
failure
* src/conf/capabilities.c, src/conf/capabilities.h: Remove
powerMgmt_valid field
* src/qemu/qemu_capabilities.c: Remove powerMgmt_valid
The capabilities XML uses the x86 specific terms 'S3', 'S4'
and 'Hybrid-Syspend'. Switch it to use the same terminology
as the API constants and virsh options, eg 'suspend_mem'
'suspend_disk' and 'suspend_hybrid'
* docs/formatcaps.html.in, docs/schemas/capability.rng,
src/conf/capabilities.c: Rename suspend constants
This adds per-device weights to <blkiotune>. Note that the
cgroups implementation only supports weights per block device,
and not per-file within the device; hence this option must be
global to the domain definition rather than tied to individual
<devices>/<disk> entries:
<domain ...>
<blkiotune>
<device>
<path>/path/to/block</path>
<weight>1000</weight>
</device>
</blkiotune>
..
This patch also adds a parameter --device-weights to virsh command
blkiotune for setting/getting blkiotune.weight_device for any
hypervisor that supports it. All <device> entries under
<blkiotune> are concatenated into a single string attribute under
virDomain{Get,Set}BlkioParameters, named "device_weight".
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Some systems support a feature known as 'Hybrid-Suspend', apart from the
usual system-wide sleep states such as Suspend-to-RAM (S3) or Suspend-to-Disk
(S4). Add the functionality to discover this power management feature and
export it in the capabilities XML under the <power_management> tag.
virt-xml-validate fails when run on a domain XML file of type 'vbox'.
For failing test case, see https://bugzilla.redhat.com/show_bug.cgi?id=757097
This patch updates the XML schema to accept all valid hypervisor
types, as well as dropping hypervisor types that are not in use
by the current code base.
Signed-off-by: Eric Blake <eblake@redhat.com>
Add documentation for the STP filtering support. Describe the XML attributes
that are supported.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch adds support for filtering of STP (spanning tree protocol) traffic
to the parser and makes us of the ebtables support for STP filtering. This code
now enables the filtering of traffic in chains with prefix 'stp'.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
With hunks borrowed from one of David Steven's previous patches, we now
add the capability of having a 'mac' chain which is useful to filter
for multiple valid MAC addresses.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch exports KVM Host Power Management capabilities as XML so that
higher-level systems management software can make use of these features
available in the host.
The script "pm-is-supported" (from pm-utils package) is run to discover if
Suspend-to-RAM (S3) or Suspend-to-Disk (S4) is supported by the host.
If either of them are supported, then a new tag "<power_management>" is
introduced in the XML under the <host> tag.
However in case the query to check for power management features succeeded,
but the host does not support any such feature, then the XML will contain
an empty <power_management/> tag. In the event that the PM query itself
failed, the XML will not contain any "power_management" tag.
To use this, new APIs could be implemented in libvirt to exploit power
management features such as S3/S4.
Add documentation for the VLAN filtering support. Describe the XML attributes
that are supported.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch adds support for filtering of VLAN (802.1Q) traffic to the
parser and makes us of the ebtables support for VLAN filtering. This code
now enables the filtering of traffic in chains with prefix 'vlan'.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch modifies the NWFilter parameter parser to support multiple
elements with the same name and to internally build a list of items.
An example of the XML looks like this:
<parameter name='TEST' value='10.1.2.3'/>
<parameter name='TEST' value='10.2.3.4'/>
<parameter name='TEST' value='10.1.1.1'/>
The list of values is then stored in the newly introduced data type
virNWFilterVarValue.
The XML formatter is also adapted to print out all items in alphabetical
order sorted by 'name'.
This patch also fixes a bug in the XML schema on the way.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch adds several aspects of documentation about the network filtering
system:
- chains, chains' priorities and chains' default priorities
- talks about lists of elements, i.e., a variable assigned multiple values
(part of already ACK-ed series)
- already mentions the vlan, stp and mac chains added later on
(https://www.redhat.com/archives/libvir-list/2011-October/msg01238.html)
- mentions limitations of vlan filtering (when sent by VM) on Linux systems
This patch enables chains that have a known prefix in their name.
Known prefixes are: 'ipv4', 'ipv6', 'arp', 'rarp'. All prefixes
are also protocols that can be evaluated on the ebtables level.
Following the prefix they will be automatically connected to an interface's
'root' chain and jumped into following the protocol they evaluate, i.e.,
a table 'arp-xyz' will be accessed from the root table using
ebtables -t nat -A <iface root table> -p arp -j I-<ifname>-arp-xyz
thus generating a 'root' chain like this one here:
Bridge chain: libvirt-O-vnet0, entries: 5, policy: ACCEPT
-p IPv4 -j O-vnet0-ipv4
-p ARP -j O-vnet0-arp
-p 0x8035 -j O-vnet0-rarp
-p ARP -j O-vnet0-arp-xyz
-j DROP
where the chain 'arp-xyz' is accessed for filtering of ARP packets.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch extends the filter XML to support priorities of chains
in the XML. An example would be:
<filter name='allow-arpxyz' chain='arp-xyz' priority='200'>
[...]
</filter>
The permitted values for priorities are [-1000, 1000].
By setting the priority of a chain the order in which it is accessed
from the interface root chain can be influenced.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch adds XML definitions for guest NUMA specification and contains
routines to parse the same. The guest NUMA specification looks like this:
<cpu>
...
<topology sockets='2' cores='4' threads='2'/>
<numa>
<cell cpus='0-7' memory='512000'/>
<cell cpus='8-15' memory='512000'/>
</numa>
...
</cpu>
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
While Xen only has a single paravirt console, UML, and
QEMU both support multiple paravirt consoles. The LXC
driver can also be trivially made to support multiple
consoles. This patch extends the XML to allow multiple
<console> elements in the XML. It also makes the UML
and QEMU drivers support this config.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Allow
multiple <console> devices
* src/lxc/lxc_driver.c, src/xen/xen_driver.c,
src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c: Update for
internal API changes
* src/security/security_selinux.c, src/security/virt-aa-helper.c:
Only label consoles that aren't a copy of the serial device
* src/qemu/qemu_command.c, src/qemu/qemu_driver.c,
src/qemu/qemu_process.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Support multiple console devices
* tests/qemuxml2xmltest.c, tests/qemuxml2argvtest.c: Extra
tests for multiple virtio consoles. Set QEMU_CAPS_CHARDEV
for all console /channel tests
* tests/qemuxml2argvdata/qemuxml2argv-channel-virtio-auto.args,
tests/qemuxml2argvdata/qemuxml2argv-channel-virtio.args
tests/qemuxml2argvdata/qemuxml2argv-console-virtio.args: Update
for correct chardev syntax
* tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.args,
tests/qemuxml2argvdata/qemuxml2argv-console-virtio-many.xml: New
test file
Allow the datacenter and compute resource parts of the path
to be prefixed with folders. Therefore, the way the path is
parsed has changed. Before, it was split in 2 or 3 items and
the items' meanings were determined by their positions. Now
the path can have 2 or more items and the the vCenter server
is asked whether a folder, datacenter of compute resource
with the specified name exists at the current hierarchy level.
Before the datacenter and compute resource lookup automatically
traversed folders during lookup. This is logic got removed
and folders have to be specified explicitly.
The proper datacenter path including folders is now used when
accessing a datastore over HTTPS. This makes virsh dumpxml
and define work for datacenters in folders.
https://bugzilla.redhat.com/show_bug.cgi?id=732676
The types used in domaincommon.rng and secret.rng should be the same.
Move genericName to basictypes.rng, then drop redundant types now
that secret.rng uses basictypes.rng.
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Add additional fields to let you specify the how to authenticate with a disk.
The secret to use may be referenced by a usage string or a UUID, i.e.:
<auth username='myuser'>
<secret type='ceph' usage='secretname'/>
</auth>
or
<auth username='myuser'>
<secret type='ceph' uuid='0a81f5b2-8403-7b23-c8d6-21ccc2f80d6f'/>
</auth>
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.com>
Add a new secret type to store a Ceph authentication key. The name
is simply an identifier for easy human reference.
The xml looks like this:
<secret ephemeral='no' private='no'>
<uuid>0a81f5b2-8403-7b23-c8d6-21ccc2f80d6f</uuid>
<usage type='ceph'>
<name>mycluster_admin</name>
</usage>
</secret>
Signed-off-by: Sage Weil <sage@newdream.net>
Signed-off-by: Josh Durgin <josh.durgin@dreamhost.net>
Define two new RPC message types VIR_NET_CALL_WITH_FDS and
VIR_NET_REPLY_WITH_FDS. These message types are equivalent
to VIR_NET_CALL and VIR_NET_REPLY, except that between the
message header, and payload there is a 32-bit integer field
specifying how many file descriptors have been passed.
The actual file descriptors are sent/recv'd out of band.
* src/rpc/virnetmessage.c, src/rpc/virnetmessage.h,
src/libvirt_private.syms: Add support for handling
passed file descriptors
* src/rpc/virnetprotocol.x: Extend protocol for FD
passing
The 5th line of every xfig file has 'Letter ' which
annoys GITs trailing-whitespace commit hook. Hand edit
the files to remove that trailing whitespace
* docs/*.fig: Remove trailing whitespace
This adds a page documenting many aspects of migration:
- The types of migration (managed direct, p2p, unmanaged direct)
- Data transports (native, tunnelled)
- Migration URIs
- Config file handling
- Example scenarios
* libvirt.css: Rules for data tables and diagrams
* Makefile.am: Include extra png/fig files
* migration-managed-direct.fig, migration-managed-direct.png,
migration-managed-direct.png, migration-managed-p2p.png,
migration-native.fig, migration-native.png,
migration-tunnel.fig, migration-tunnel.png,
migration-unmanaged-direct.fig, migration-unmanaged-direct.png:
Diagrams of migration
* migration.html.in, sitemap.html.in: New migration doc
This attribute says what to do with cdrom (or floppy) if
the source is missing. It accepts:
- mandatory - fail if missing for any reason (the default)
- requisite - fail if missing on boot up, drop if missing on
migrate/restore/revert
- optional - drop if missing at any start attempt.
However, this patch introduces only XML part of this new
functionality.
In a recent expansion of the documentation on network forward modes, I
incorrectly stated that incoming sessions to guests on routed networks
were blocked. This is true for guests on NATed networks, but not
routed. This patch corrects that error, and adds a pointer to the
nwfilter page for those who do want to restrict incoming sessions to
hosts on routed networks.
Clarify some of the effects of managed passthrough <hostdev> devices;
with recent changes (commit d093547), a nodedev-reattach is only needed
to pair up to an explicit nodedev-dettach (but beware that older
virt-manager has a bug where it uses explicit nodedev-dettach under the
hood when using the gui to hotplug a hostdev device).
* docs/formatdomain.html.in: Mention reattach.
* tools/virsh.pod (nodedev): Mention managed mode.
This adds support for a libvirt client configuration file
either /etc/libvirt/libvirt.conf for privileged clients,
or $HOME/.libvirt/libvirt.conf for unprivileged clients.
It allows one parameter
uri_aliases = [
"hail=qemu+ssh://root@hail.cloud.example.com/system",
"sleet=qemu+ssh://root@sleet.cloud.example.com/system",
]
Any call to virConnectOpen with a non-NULL URI will first
attempt to match against the uri_aliases list. An application
can disable this by using VIR_CONNECT_NO_ALIASES
* docs/uri.html.in: Document URI aliases
* include/libvirt/libvirt.h.in: Add VIR_CONNECT_NO_ALIASES
* libvirt.spec.in, mingw32-libvirt.spec.in: Add /etc/libvirt/libvirt.conf
* src/Makefile.am: Install default config file
* src/libvirt.c: Add support for URI aliases
* src/remote/remote_driver.c: Don't try to handle URIs
with no scheme and which clearly are not paths
* src/util/conf.c: Don't raise error on virConfFree(NULL)
* src/xen/xen_driver.c: Don't raise error on URIs
with no scheme
A few people have attempted to use the new forwarding modes with older
versions of libvirt. The docs where the modes are described have
always stated the minimum required libvirt version, but the examples
at the end didn't, which I believe is what has caused the confusion.
Similarly, the section on portgroups now has a version tag added at
the beginning.
I also noticed that there was no example of defining a <dns> hostname,
so I added one, as well as making the domain name example more
recognizable (by adding ".com" to the domain).
VirtFS allows the user to choose between path/handle based fs driver.
As of now, libvirt hardcoded path based driver only. This patch provides
a solution to allow user to choose between path/handle based fs driver.
Sample:
<filesystem type='mount'>
<driver type='handle'/>
<source dir='/folder/to/share1'/>
<target dir='mount_tag1'/>
</filesystem>
<filesystem type='mount'>
<driver type='path'/>
<source dir='/folder/to/share2'/>
<target dir='mount_tag2'/>
</filesystem>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Previously libvirt's disk device XML only had a single attribute,
error_policy, to control both read and write error policy, but qemu
has separate options for controlling read and write. In one case
(enospc) a policy is allowed for write errors but not read errors.
This patch adds a separate attribute that sets only the read error
policy. If just error_policy is set, it will apply to both read and
write error policy (previous behavior), but if the new rerror_policy
attribute is set, it will override error_policy for read errors only.
Possible values for rerror_policy are "stop", "report", and "ignore"
("report" is the qemu-controlled default for rerror_policy when
error_policy isn't specified).
For consistency, the value "report" has been added to the possible
values for error_policy as well.
When booting a virtual machine with a kernel/initrd it is possible
to pass command line arguments using the <cmdline>...args...</cmdline>
element in the guest XML. These appear to the kernel / init process
in /proc/cmdline.
When booting a container we do not have a custom /proc/cmdline,
but we can easily set an environment variable for it. Ideally
we could pass individual arguments to the init process as a
regular set of 'char *argv[]' parameters, but that would involve
libvirt parsing the <cmdline> XML text. This can easily be added
later, even if we add the env variable now
* docs/drvlxc.html.in: Document env variables passed to LXC
* src/conf/domain_conf.c: Add <cmdline> to be parsed for
guests of type='exe'
* src/lxc/lxc_container.c: Set LIBVIRT_LXC_CMDLINE env var
When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
there is no option "none":
>From libvirt/src/conf/domain_conf.c
<snip>
VIR_ENUM_IMPL(virDomainTimerTickpolicy,
VIR_DOMAIN_TIMER_TICKPOLICY_LAST,
"delay",
"catchup",
"merge",
"discard");
</snip>
Replacing with delay.
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Coupled with the recent virsh nodedev-* doc patch, this should now
give a better picture of libvirt node device handling.
* docs/formatnode.html.in: Fill in page.
This patch was made in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=738095
In short, qemu's default for the rombar setting (which makes the
firmware ROM of a PCI device visible/not on the guest) was previously
0 (not visible), but they recently changed the default to 1
(visible). Unfortunately, there are some PCI devices that fail in the
guest when rombar is 1, so the setting must be exposed in libvirt to
prevent a regression in behavior (it will still require explicitly
setting <rom bar='off'/> in the guest XML).
rombar is forced on/off by adding:
<rom bar='on|off'/>
inside a <hostdev> element that defines a PCI device. It is currently
ignored for all other types of devices.
At the moment there is no clean method to determine whether or not the
rombar option is supported by QEMU - this patch uses the advice of a
QEMU developer to assume support for qemu-0.12+. There is currently a
patch in the works to put this information in the output of "qemu-kvm
-device pci-assign,?", but of course if we switch to keying off that,
we would lose support for setting rombar on all the versions of qemu
between 0.12 and whatever version gets that patch.
QEMU 0.13 introduced cache=unsafe for -drive, this patch exposes
it in the libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_UNSAFE),
as even if $prefix_CACHE_V2 is set, we can't know if unsafe
is supported.
* Improved the reliability of qemu cache type detection.
A new element is introduced to XML that allows to control
state of virtual network interfaces in hypervisors.
Live modification of the link state allows networking tools
propagate topology changes to guest OS or testing of
scenarios in complex (virtual) networks.
This patch adds elements to XML grammars and parsing and generating
code.
It is important to be able to attach USB redirected devices to a
particular controller (one that supports USB2 for instance).
Without this patch, only the default bus was used.
<redirdev bus='usb' type='spicevmc'>
<address type='usb' bus='0' port='4'/>
</redirdev>
I got confused when 'virsh domblkinfo dom disk' required the
path to a disk (which can be ambiguous, since a single file
can back multiple disks), rather than the unambiguous target
device name that I was using in disk snapshots. So, in true
developer fashion, I went for the best of both worlds - all
interfaces that operate on a disk (aka block) now accept
either the target name or the unambiguous path to the backing
file used by the disk.
* src/conf/domain_conf.h (virDomainDiskIndexByName): Add
parameter.
(virDomainDiskPathByName): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainDiskIndexByName): Also allow
searching by path, and decide whether ambiguity is okay.
(virDomainDiskPathByName): New function.
(virDomainDiskRemoveByName, virDomainSnapshotAlignDisks): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainBlockPeek)
(qemuDomainAttachDeviceConfig, qemuDomainUpdateDeviceConfig)
(qemuDomainGetBlockInfo, qemuDiskPathToAlias): Likewise.
* src/qemu/qemu_process.c (qemuProcessFindDomainDiskByPath):
Likewise.
* src/libxl/libxl_driver.c (libxlDomainAttachDeviceDiskLive)
(libxlDomainDetachDeviceDiskLive, libxlDomainAttachDeviceConfig)
(libxlDomainUpdateDeviceConfig): Likewise.
* src/uml/uml_driver.c (umlDomainBlockPeek): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainBlockPeek): Likewise.
* docs/formatsnapshot.html.in: Update documentation.
* tools/virsh.pod (domblkstat, domblkinfo): Likewise.
* docs/schemas/domaincommon.rng (diskTarget): Tighten pattern on
disk targets.
* docs/schemas/domainsnapshot.rng (disksnapshot): Update to match.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: Update test.
Adds an optional element to <domainsnapshot>, which will be used
to give user control over external snapshot filenames on input,
and specify generated filenames on output.
For now, no driver accepts this element; that will come later.
<domainsnapshot>
...
<disks>
<disk name='vda' snapshot='no'/>
<disk name='vdb' snapshot='internal'/>
<disk name='vdc' snapshot='external'>
<driver type='qcow2'/>
<source file='/path/to/new'/>
</disk>
</disks>
<domain>
...
<devices>
<disk ...>
<driver name='qemu' type='raw'/>
<target dev='vdc'/>
<source file='/path/to/old'/>
</disk>
</devices>
</domain>
</domainsnapshot>
* src/conf/domain_conf.h (_virDomainSnapshotDiskDef): New type.
(_virDomainSnapshotDef): Add new elements.
(virDomainSnapshotAlignDisks): New prototype.
* src/conf/domain_conf.c (virDomainSnapshotDiskDefClear)
(virDomainSnapshotDiskDefParseXML, disksorter)
(virDomainSnapshotAlignDisks): New functions.
(virDomainSnapshotDefParseString): Parse new fields.
(virDomainSnapshotDefFree): Clean them up.
(virDomainSnapshotDefFormat): Output them.
* src/libvirt_private.syms (domain_conf.h): Export new function.
* docs/schemas/domainsnapshot.rng (domainsnapshot, disksnapshot):
Add more xml.
* docs/formatsnapshot.html.in: Document it.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: New test.
* tests/domainsnapshotxml2xmlout/disk_snapshot.xml: Update.
In order to distinguish disk snapshots from system checkpoints, a
new state value that is only valid for snapshots is helpful.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_LAST): New placeholder.
* src/conf/domain_conf.h (virDomainSnapshotState): New enum mapping.
(VIR_DOMAIN_DISK_SNAPSHOT): New internal enum value.
* src/conf/domain_conf.c (virDomainState): Use placeholder.
(virDomainSnapshotState): Extend mapping by one for use in snapshot.
(virDomainSnapshotDefParseString, virDomainSnapshotDefFormat):
Handle new state.
(virDomainObjSetState, virDomainStateReasonToString)
(virDomainStateReasonFromString): Avoid compiler warnings.
* tools/virsh.c (vshDomainState, vshDomainStateReasonToString):
Likewise.
* src/libvirt_private.syms (domain_conf.h): Export new functions.
* docs/schemas/domainsnapshot.rng: Tighten state definition.
* docs/formatsnapshot.html.in: Document it.
* tests/domainsnapshotxml2xmlout/disk_snapshot.xml: New test.
As discussed here:
https://www.redhat.com/archives/libvir-list/2011-August/msg00361.htmlhttps://www.redhat.com/archives/libvir-list/2011-August/msg00552.html
Adds snapshot attribute and transient sub-element:
<devices>
<disk type=... snapshot='no|internal|external'>
...
<transient/>
</disk>
</devices>
* docs/schemas/domaincommon.rng (snapshot): New define.
(disk): Add snapshot and persistent attributes.
* docs/formatdomain.html.in: Document them.
* src/conf/domain_conf.h (virDomainDiskSnapshot): New enum.
(_virDomainDiskDef): New fields.
* tests/qemuxml2argvdata/qemuxml2argv-disk-transient.xml: New
test of rng, no args counterpart until qemu support is complete.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.args: New
file, snapshot attribute does not affect args.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.xml: Likewise.
* tests/qemuxml2argvtest.c (mymain): Run new test.
This patch will probably cause merge conflicts to those trying
to do backports. The end goal is simple - domaincommon.rng
should be the state of domain.rng pre-patch, with a few lines
tweaked in the header, while domain.rng post-patch is now just
a shell that includes domaincommon.rng and sets the <start>.
* docs/schemas/domain.rng: Move guts...
* docs/schemas/domaincommon.rng: ...to new file.
* docs/schemas/domainsnapshot.rng: Allow new xml.
* docs/schemas/Makefile.am (schema_DATA): Distribute new file.
* tests/domainsnapshotxml2xmlout/full_domain.xml: New test.
* libvirt.spec.in (%files client): Ship new file. Sort lines.
* mingw32-libvirt.spec.in: Likewise.
Just like VM saved state images (virsh save), snapshots MUST
track the inactive domain xml to detect any ABI incompatibilities.
The indentation is not perfect, but functionality comes before form.
Later patches will actually supply a full domain; for now, this
wires up the storage to support one, but doesn't ever generate one
in dumpxml output.
Happily, libvirt.c was already rejecting use of VIR_DOMAIN_XML_SECURE
from read-only connections, even though before this patch, there was
no information to be secured by the use of that flag.
And while we're at it, mark the libvirt snapshot metadata files
as internal-use only.
* src/libvirt.c (virDomainSnapshotGetXMLDesc): Document flag.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Add member.
(virDomainSnapshotDefParseString, virDomainSnapshotDefFormat):
Update signature.
* src/conf/domain_conf.c (virDomainSnapshotDefFree): Clean up.
(virDomainSnapshotDefParseString): Optionally parse domain.
(virDomainSnapshotDefFormat): Output full domain.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML)
(esxDomainSnapshotGetXMLDesc): Update callers.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML)
(vboxDomainSnapshotGetXMLDesc): Likewise.
* src/qemu/qemu_driver.c (qemuDomainSnapshotCreateXML)
(qemuDomainSnapshotLoad, qemuDomainSnapshotGetXMLDesc)
(qemuDomainSnapshotWriteMetadata): Likewise.
* docs/formatsnapshot.html.in: Rework doc example.
Based on a patch by Philipp Hahn.
The first two flags are essential for being able to replicate
snapshot hierarchies across multiple hosts, which will come in
handy for supervised migrations. It also allows a management app
to take a snapshot of a transient domain, save the metadata, stop
the domain, recreate a new transient domain by the same name,
redefine the snapshot, then revert to it.
This is not quite as convenient as leaving the metadata behind
after a domain is no longer around, but doing that has a few
problems: 1. the libvirt API can only delete snapshot metadata
if there is a valid domain handle to use to get to that snapshot
object - if stale data is left behind without a domain, there is
no way to request that the data be cleaned up. 2. creating a new
domain with the same name but different uuid than the older
domain where a snapshot existed cannot use the older snapshot
data; this risks confusing libvirt, and forbidding the stale
data is similar to the recent patch to forbid stale managed save.
The first two flags might be useful on hypervisors with no metadata,
but only for modifying the notion of the current snapshot;
however, I don't know how to do that for ESX or VBox.
The third flag is a convenience option, to combine a creation with
a delete metadata into one step. It is trivial for hypervisors
with no metadata.
The qemu changes will be involved enough to warrant a separate patch.
* include/libvirt/libvirt.h.in
(VIR_DOMAIN_SNAPSHOT_CREATE_REDEFINE)
(VIR_DOMAIN_SNAPSHOT_CREATE_CURRENT)
(VIR_DOMAIN_SNAPSHOT_CREATE_NO_METADATA): New flags.
* src/libvirt.c (virDomainSnapshotCreateXML): Document them, and
enforce mutual exclusion.
* src/esx/esx_driver.c (esxDomainSnapshotCreateXML): Trivial
implementation.
* src/vbox/vbox_tmpl.c (vboxDomainSnapshotCreateXML): Likewise.
* docs/formatsnapshot.html.in: Document re-creation.
So that devices can be attached to hubs. Example, to attach to first
port of a usb-hub on port 1.
<hub type='usb'>
<address type='usb' bus='0' port='1'/>
</hub>
<input type='mouse' type='usb'>
<address type='usb' bus='0' port='1.1'/>
</hub>
also add a test entry
Newer QEMU introduced cache=directsync for -drive, this patchset
is to expose it in libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_DIRECTSYNC),
As even $prefix_CACHE_V2 is set, we can't known if directsync
is supported.
Audit all changes to the qemu vm->current_snapshot, and make them
update the saved xml file for both the previous and the new
snapshot, so that there is always at most one snapshot with
<active>1</active> in the xml, and that snapshot is used as the
current snapshot even across libvirtd restarts.
This patch does not fix the case of virDomainSnapshotDelete(,CHILDREN)
where one of the children is the current snapshot; that will be later.
* src/conf/domain_conf.h (_virDomainSnapshotDef): Alter member
type and name.
* src/conf/domain_conf.c (virDomainSnapshotDefParseString)
(virDomainSnapshotDefFormat): Update clients.
* docs/schemas/domainsnapshot.rng: Tighten rng.
* src/qemu/qemu_driver.c (qemuDomainSnapshotLoad): Reload current
snapshot.
(qemuDomainSnapshotCreateXML, qemuDomainRevertToSnapshot)
(qemuDomainSnapshotDiscard): Track current snapshot.
In some versions of qemu, both virtio-blk-pci and virtio-net-pci
devices can have an event_idx setting that determines some details of
event processing. When it is enabled, it "reduces the number of
interrupts and exits for the guest". qemu will automatically enable
this feature when it is available, but there may be cases where this
new feature could actually make performance worse (NB: no such case
has been found so far).
As a safety switch in case such a situation is encountered in the
field, this patch adds a new attribute "event_idx" to the <driver>
element of both disk and interface devices. event_idx can be set to
"on" (to force event_idx on in case qemu has it disabled by default)
or "off" (for force event_idx off). In the case that event_idx support
isn't present in qemu, the attribute is ignored (this on the advice of
the qemu developer).
docs/formatdomain.html.in: document the new flag (marking it as
"don't mess with this!"
docs/schemas/domain.rng: add event_idx in appropriate places
src/conf/domain_conf.[ch]: add event_idx to parser and formatter
src/libvirt_private.syms: export
virDomainVirtioEventIdx(From|To)String
src/qemu/qemu_capabilities.[ch]: detect and report event_idx in
disk/net
src/qemu/qemu_command.c: add event_idx parameter to qemu commandline
when appropriate.
tests/qemuxml2argvdata/qemuxml2argv-event_idx.args,
tests/qemuxml2argvdata/qemuxml2argv-event_idx.xml,
tests/qemuxml2argvtest.c,
tests/qemuxml2xmltest.c: test cases for event_idx.
Currently only tabs and blanks are used for tokenizing the description,
which breaks when a term is at the end of a line or has () appended to
it.
1. Use also other white space characters such as new-lines and carriage
return for splitting.
2. Remove some common non-word characters from the token before lookup.
Signed-off-by: Philipp Hahn <hahn@univention.de>
* remote.html.in: Remove obsolete notes about internals of the
RPC protocol
* internals/rpc.html.in: Extensive docs on RPC protocol/API
* sitemap.html.in: Add new page
When the description of an entry is too long and needs multiple lines,
all other table cells of the same row are currently vertically aligned
on center. Without row borders or different background colors for
alternating rows this is hard to read.
Change the style-sheet to align the table cells of a row on top.
Signed-off-by: Philipp Hahn <hahn@univention.de>
Someone in an IRC channel or an email pointed out a few days ago that
the examples of IPv6 addresses in the libvirt documentation were not
in the officially reserved "documentation" range. This addresses their
concern.
This should have been done with the rest of the patch for virtual
switch / network device abstraction. If documents the new elements
(and new usage of existing elements) in the <network> XML to support
libvirt networks that use existing host bridges and macvtap direct
connections, as well as the new <portgroup> element.
* configure.ac docs/news.html.in libvirt.spec.in: updates for new
release
* po/*.po*: pulled translations from the transifex teams and regenerated
localizations
I went with the shorter license notice used by src/libvirt.c,
rather than spelling out the full LGPLv2+ clause into each of
these files.
* configure.ac: Declare copyright.
* all Makefile.am: Likewise.
Once it's plugged in, the <listen> element will be an optional
replacement for the "listen" attribute that graphics elements already
have. If the <listen> element is type='address', it will have an
attribute called 'address' which will contain an IP address or dns
name that the guest's display server should listen on. If, however,
type='network', the <listen> element should have an attribute called
'network' that will be set to the name of a network configuration to
get the IP address from.
* docs/schemas/domain.rng: updated to allow the <listen> element
* docs/formatdomain.html.in: document the <listen> element and its
attributes.
* src/conf/domain_conf.[hc]:
1) The domain parser, formatter, and data structure are modified to
support 0 or more <listen> subelements to each <graphics>
element. The old style "legacy" listen attribute is also still
accepted, and will be stored internally just as if it were a
separate <listen> element. On output (i.e. format), the address
attribute of the first <listen> element of type 'address' will be
duplicated in the legacy "listen" attribute of the <graphic>
element.
2) The "listenAddr" attribute has been removed from the unions in
virDomainGRaphicsDef for graphics types vnc, rdp, and spice.
This attribute is now in the <listen> subelement (aka
virDomainGraphicsListenDef)
3) Helper functions were written to provide simple access
(both Get and Set) to the listen elements and their attributes.
* src/libvirt_private.syms: export the listen helper functions
* src/qemu/qemu_command.c, src/qemu/qemu_hotplug.c,
src/qemu/qemu_migration.c, src/vbox/vbox_tmpl.c,
src/vmx/vmx.c, src/xenxs/xen_sxpr.c, src/xenxs/xen_xm.c
Modify all these files to use the listen helper functions rather
than directly referencing the (now missing) listenAddr
attribute. There can be multiple <listen> elements to a single
<graphics>, but the drivers all currently only support one, so all
replacements of direct access with a helper function indicate index
"0".
* tests/* - only 3 of these are new files added explicitly to test the
new <listen> element. All the others have been modified to reflect
the fact that any legacy "listen" attributes passed in to the domain
parse will be saved in a <listen> element (i.e. one of the
virDomainGraphicsListenDefs), and during the domain format function,
both the <listen> element as well as the legacy attributes will be
output.
Every DomainNetDef has a bandwidth, as does every portgroup.
Whenever a DomainNetDef of type NETWORK is about to be used, a call is
made to networkAllocateActualDevice(). This function chooses the "best"
bandwidth object and places it in the DomainActualNetDef.
From that point on, whenever some code needs to use the bandwidth data
for the interface, it's retrieved with virDomainNetGetActualBandwidth(),
which will always return the "best" info as determined in the
previous step.
We had a bit too many elements crammed in there. Separate it into different
headings:
- CPU Allocation (<vcpus>)
- CPU Tuning (<cputune>)
- Memory allocation (<memory> and <currentMemory>)
- Memory backing (<memoryBacking>)
- Memory tuning (<memtune>)
- Numa tuning (<numatune>)
- Block I/O tuning (<blkiotune>)
Define new 'bandwidth' element with possible child element 'inbound'
and 'outbound' addressing incoming and outgoing traffic respectively:
<bandwidth>
<inbound average='1000' peak='2000' burst='5120'/>
<outbound average='500'/>
</bandwidth>
Leaving any element out means not to shape traffic in that
direction.
The units for average and peak (rate) are in kilobytes per second,
for burst (size) are just in kilobytes.
This element can be inserted into domain's 'interface' and
'network'.
Set up the types for the block pull functions and insert them into the
virDriver structure definition. Symbols are exported in this patch to
prevent
documentation compile failures.
* include/libvirt/libvirt.h.in: new API
* src/driver.h: add the new entry to the driver structure
* python/generator.py: fix compiler errors, the actual python bindings
* are
implemented later
* src/libvirt_public.syms: export symbols
* docs/apibuild.py: Extend 'unsigned long' parameter exception to this
* API
The network XML is updated in the following ways:
1) The <forward> element can now contain a list of forward interfaces:
<forward .... >
<interface dev='eth10'/>
<interface dev='eth11'/>
<interface dev='eth12'/>
<interface dev='eth13'/>
</forward>
The first of these takes the place of the dev attribute that is
normally in <forward> - when defining a network you can specify
either one, and on output both will be present. If you specify
both on input, they must match.
2) In addition to forward modes of 'nat' and 'route', these new modes
are supported:
private, passthrough, vepa - when this network is referenced by a
domain's interface, it will have the same effect as if the
interface had been defined as type='direct', e.g.:
<interface type='direct'>
<source mode='${mode}' dev='${dev}>
...
</interface>
where ${mode} is one of the three new modes, and ${dev} is an interface
selected from the list given in <forward>.
bridge - if a <forward> dev (or multiple devs) is defined, and
forward mode is 'bridge' this is just like the modes 'private',
'passthrough', and 'vepa' above. If there is no forward dev
specified but a bridge name is given (e.g. "<bridge
name='br0'/>"), then guest interfaces using this network will use
libvirt's "host bridge" mode, equivalent to this:
<interface type='bridge'>
<source bridge='${bridge-name}'/>
...
</interface>
3) A network can have multiple <portgroup> elements, which may be
selected by the guest interface definition (by adding
"portgroup='${name}'" in the <source> element along with the
network name). Currently a portgroup can only contain a
virtportprofile, but the intent is that other configuration items
may be put there int the future (e.g. bandwidth config). When
building a guest's interface, if the <interface> XML itself has no
virtportprofile, and if the requested network has a portgroup with
a name matching the name given in the <interface> (or if one of the
network's portgroups is marked with the "default='yes'" attribute),
the virtportprofile from that portgroup will be used by the
interface.
4) A network can have a virtportprofile defined at the top level,
which will be used by a guest interface when connecting in one of
the 'direct' modes if the guest interface XML itself hasn't
specified any virtportprofile, and if there are also no matching
portgroups on the network.
the domain XML <interface> element is updated in the following ways:
1) <virtualportprofile> can be specified when source type='network'
(previously it was only valid for source type='direct')
2) A new attribute "portgroup" has been added to the <source>
element. When source type='network' (the only time portgroup is
recognized), extra configuration information will be taken from the
<portgroup> element of the given name in the network definition.
3) Each virDomainNetDef now also potentially has a
virDomainActualNetDef which is a private object (never
exported/imported via the public API, and not defined in the RNG) that
is used to maintain information about the physical device that was
actually used for a NetDef of type VIR_DOMAIN_NET_TYPE_NETWORK.
The virDomainActualNetDef will only be parsed/formatted if the
parse/format function is called with the
VIR_DOMAIN_XML_INTERNAL_ACTUAL_NET flag set (which is only needed when
saving/loading a running domain's state info to the stateDir).
virtPortProfiles are currently only used in the domain XML, but will
soon also be used in the network XML. To prepare for that change, this
patch moves the structure definition into util/network.h and the parse
and format functions into util/network.c (I decided that this was a
better choice than macvtap.h/c for something that needed to always be
available on all platforms).
Commit 8665f85 introduced a slight regression in doc generation,
since make only quits a rule on the first failed command ending
with a newline rather than a semicolon.
* docs/Makefile.am (html/index.html): Don't use xmllint unless
xsltproc succeeded.
* .gitignore: Ignore recently updated stamp file name.
The current API build scripts will continue and exit with a zero
status even if they find problems. This has been the cause of many
build problems, or hidden build errors, in the past. Change the
scripts so they always exit with a non-zero status for any problems
they do not understand. Also turn off all debug output by default
so they respect $(AM_V_GEN)
* docs/Makefile.am: Use $(AM_V_GEN) for API/HTML scripts
* docs/apibuild.py, python/generator.py: Exit with non-zero status
if problems are found. Also be silent, not outputting any debug
messages.
* src/Makefile.am: Use $(AM_V_GEN) for ESX generator
* python/Makefile.am: Tweak rule
The "libvirt supports:" section on the main page of libvirt.org
contains a list of hypervisors with links that point to the sites of
the underlying virt technologies. The entry for KVM points to
http://www.linux-kvm.org/, for example. People coming to libvirt.org
for the first time are likely to know about those sites, and they're
probably interested in how libvirt manages those technologies. This
patch points those links to the libvirt driver pages instead. It also
consolidates KVM and QEMU as there is only one libvirt driver page for
them. Finally, it adds a line about networking support.
v2: incorporate Eric's feedback adding project links to driver pages.
website: Add project links to KVM/QEMU driver page
website: Add project links to Xen driver page
website: Add project links to LXC driver page
website: Add project links to OpenVZ driver page
website: Add project links to UML driver page
website: Add project links to Virtualbox driver page
website: Add project links to ESX driver page
website: Add project links to VMware driver page
When using virCommandRunAsync and saving the pid for later, it
is useful to be able to reap that pid in the same way that it
would have been auto-reaped by virCommand if we had passed
NULL for the pid argument in the first place.
* src/util/command.c (virPidWait, virPidAbort): New functions,
created from...
(virCommandWait, virCommandAbort): ...bodies of these.
(includes): Drop duplicate <stdlib.h>. Ensure that our pid_t
assumptions hold.
(virCommandRunAsync): Improve documentation.
* src/util/command.h (virPidWait, virPidAbort): New prototypes.
* src/libvirt_private.syms: Export them.
* docs/internals/command.html.in: Document them.
Without this patch, the make rule in a VPATH build was trying to
invoke ../../docs/../../docs/todo.pl, which didn't exist.
* docs/Makefile.am (todo.html.in): Using $< already implies
$(srcdir) in GNU make VPATH situations.
Set StrictHostKeyChecking=no to auto-accept new ssh host keys if the
no_verify extra parameter was specified. This won't disable host key
checking for already known hosts. Includes a test and documentation.
Kernel cmdline args can be passed to xen pv domains even when a
bootloader is specified. The current config-to-sxpr mapping
ignores cmdline when bootloader is present.
Since the xend sub-driver is used with many xen toolstack versions,
this patch takes conservative approach of adding an else block to
existing !def->os.bootloader, and only appends sxpr if def->os.cmdline
is non-NULL.
V2: Fix existing testcase broken by this patch and add new testcases
This patch creates new <bios> element which, at this time has only the
attribute useserial='yes|no'. This attribute allow users to use
Serial Graphics Adapter and see BIOS messages from the very first moment
domain boots up. Therefore, users can choose boot medium, set PXE, etc.
This option accepts 3 values:
-keep, to keep current client connected (Spice+VNC)
-disconnect, to disconnect client (Spice)
-fail, to fail setting password if there is a client connected (Spice)
Add libvirt support for MicroBlaze architecture as a QEMU target. Based on mips/mipsel pattern.
Signed-off-by: John Williams <john.williams@petalogix.com>
No change in wording. One spacing change in a <pre>, noticed because
of odd XML formatting online; the rest is in free-flowing text to
make it easier to see nesting levels in the document.
* docs/formatdomain.html.in: Adjust spacing. Break long lines.
domain.rng, network.rng, and interface.rng already use a few of the
same types (or in some cases *should* but don't), and an upcoming code
change will have them sharing even more. To prepare for that, this
patch takes those common data type definitions and moves them into
basictypes.rng.
This may break some rule about the need to RNG files to be autonomous
or something, but I saw that storageencryption.rng is used in this
way, so I figured it must not be completely against the law...
Add a new attribute to the <seclabel> XML to allow resource
relabelling to be enabled with static label usage.
<seclabel model='selinux' type='static' relabel='yes'>
<label>system_u:system_r:svirt_t:s0:c392,c662</label>
</seclabel>
* docs/schemas/domain.rng: Add relabel attribute
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parse
the 'relabel' attribute
* src/qemu/qemu_process.c: Unconditionally clear out the
'imagelabel' attribute
* src/security/security_apparmor.c: Skip based on 'relabel'
attribute instead of label type
* src/security/security_selinux.c: Skip based on 'relabel'
attribute instead of label type and fill in <imagelabel>
attribute if relabel is enabled.
Normally the dynamic labelling mode will always use a base
label of 'svirt_t' for VMs. Introduce a <baselabel> field
in the <seclabel> XML to allow this base label to be changed
eg
<seclabel type='dynamic' model='selinux'>
<baselabel>system_u:object_r:virt_t:s0</baselabel>
</seclabel>
* docs/schemas/domain.rng: Add <baselabel>
* src/conf/domain_conf.c, src/conf/domain_conf.h: Parsing
of base label
* src/qemu/qemu_process.c: Don't reset 'model' attribute if
a base label is specified
* src/security/security_apparmor.c: Refuse to support base label
* src/security/security_selinux.c: Use 'baselabel' when generating
label, if available
Add a page which documents how to configure lock managers,
focusing on use of sanlock with the QEMU/KVM driver
* docs/locking.html.in: Docs about lock managers
* docs/sitemap.html.in: Add lock manager config to
the deployment section
The sub-elements of <ip> had been placed at the same level of
indentation as ip itself, implying that they were really elements of
<network>. Within that, sub-elements of ip/dhcp were also at that same
level. These have been double-indented.
At the same time, I realized that the documentation for the new <dns>
element had been placed right in the middle of the description of the
sub-elements of <ip>. I moved it up out of the way.
This commit introduces names definition for the DNS hosts file using
the following syntax:
<dns>
<host ip="192.168.1.1">
<name>alias1</name>
<name>alias2</name>
</host>
</dns>
Some of the improvements and fixes were done by Laine Stump so
I'm putting him into the SOB clause again ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
This commit introduces the <dns> element and <txt> record for the
virtual DNS network. The DNS TXT record can be defined using following
syntax in the network XML file:
<dns>
<txt name="example" value="example value" />
</dns>
Also, the Relax-NG scheme has been altered to allow the texts without
spaces only for the name element and some nitpicks about memory
free'ing have been fixed by Laine so therefore I'm adding Laine to the
SOB clause ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
This patch adds documentation about the 802.1Qbh related parameters
of the virtualport element for 'direct' interfaces.
Signed-off-by: David S. Wang <dwang2@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
This fixes a number of issues most of them raised by Eric Blake on the
generated documentation output:
- parsing of "long long int" and similar
- add parsing of unions within a struct
- remove spurious " * " fron comments on structure fields and enums
- fix concatenation of base type and name in arrays
- extend XSLT to cope with union in structs
* docs/apibuild.py: fix and extend API extraction tool
* docs/newapi.xsl: extend the stylesheets to cope with union in
public structures
For virtio disks and interfaces, qemu allows users to enable or disable
ioeventfd feature. This means, qemu can execute domain code, while
another thread waits for I/O event. Basically, in some cases it is win,
in some loss. This feature is available via 'ioeventfd' attribute in disk
and interface <driver> element. It accepts 'on' and 'off'. Leaving this
attribute out defaults to hypervisor decision.
From a security pov copy and paste between the guest and the client is not
always desirable. So we need to be able to enable/disable this. The best place
to do this from an administration pov is on the hypervisor, so the qemu cmdline
is getting a spice disable-copy-paste option, see bug 693645. Example qemu
invocation:
qemu -spice port=5932,disable-ticketing,disable-copy-paste
https://bugzilla.redhat.com/show_bug.cgi?id=693661
For backwards compatibility, if no <video> is set but there is a
<graphics> tag, then we add a default <video> according to the
guest type. Add docs to tell the user about this to not make
them confused. Especially if they remove the video (such as via
"virsh edit"), it will be surprised for them to see the video
element is still in domain XML.
Partial revert of commit c3c30d4de9.
* docs/Makefile.am (internals/%.html.tmp): Restore MKDIR_P; it is
needed for intermediate file after all.
Reported by Daniel P. Berrange.
A lock manager may operate in various modes. The direct mode of
operation is to obtain locks based on the resources associated
with devices in the XML. The indirect mode is where the app
creating the domain provides explicit leases for each resource
that needs to be locked. This XML extension allows for listing
resources in the XML
<devices>
...
<lease>
<lockspace>somearea</lockspace>
<key>thequickbrownfoxjumpsoverthelazydog</key>
<target path='/some/lease/path' offset='23432'/>
</lease>
...
</devices>
The 'lockspace' is a unique identifier for the lockspace which
the lease is associated
The 'key' is a unique identifier for the resource associated
with the lease.
The 'target' is the file on disk where the leases are held.
* docs/schemas/domain.rng: Add lease schema
* src/conf/domain_conf.c, src/conf/domain_conf.h: parsing and
formatting for leases
* tests/qemuxml2argvdata/qemuxml2argv-lease.args,
tests/qemuxml2argvdata/qemuxml2argv-lease.xml,
tests/qemuxml2xmltest.c: Test XML handling for leases
I noticed this while building from libvirt.git on RHEL 5.6:
Generating internals/command.html.tmp
mkdir: cannot create directory `/internals': Permission denied
If I had been building as root instead, this pollutes /.
Older autoconf lacks $(builddir), but it is rigorously equal to '.'
in newer autoconf, so we could use '$(MKDIR_P) internals' instead.
However, since internals/command.html is part of the tarball, we
_already_ build it in $(srcdir), not $(builddir) during VPATH
builds, so the mkdir is wasted effort!
* docs/Makefile.am (internals/%.html.tmp): Drop unused mkdir.
This fixes this three warnings from the parser by allowing the parser
to ignore some macros in the same way as it can ignore functions.
Parsing ./../include/libvirt/libvirt.h
Misformatted macro comment for _virSchedParameter
Expecting '* _virSchedParameter:' got '* virSchedParameter:'
Misformatted macro comment for _virBlkioParameter
Expecting '* _virBlkioParameter:' got '* virBlkioParameter:'
Misformatted macro comment for _virMemoryParameter
Expecting '* _virMemoryParameter:' got '* virMemoryParameter:'
Since -vnc uses ':' to separate the address from the port, raw
IPv6 addresses need to be escaped like [addr]:port
* src/qemu/qemu_command.c: Escape raw IPv6 addresses with []
* tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.args,
tests/qemuxml2argvdata/qemuxml2argv-graphics-vnc.xml: Tweak
to test Ipv6 escaping
* docs/schemas/domain.rng: Allow Ipv6 addresses, or hostnames
in <graphics> listen attributes
This adds a streaming-video=filter|all|off attribute. It is used to change
the behavior of video stream detection in spice, the default is filter (the
default for libvirt is not to specify it - the actual default is defined in
libspice-server.so).
Usage:
<graphics type='spice' autoport='yes'>
<streaming mode='off'/>
</graphics>
Tested with the above and with tests/qemuxml2argvtest.
Signed-off-by: Alon Levy <alevy@redhat.com>
This patch enables filtering of gratuitous ARP packets using the following XML:
<rule action='accept' direction='in' priority='425'>
<arp gratuitous='true'/>
</rule>
starting with kernel 2.6.38 macvtap supports a 'passthru' mode for
attaching virtual functions of a SRIOV capable network card directly to a VM.
This patch adds the capability to configure such a device.
Signed-off-by: Dirk Herrendoerfer <d.herrendoerfer@herrendoerfer.name>
