Make MIGRATION_OUT use the new helper methods.
This also introduces new protection to migration v3 process: the
migration job is held from Begin to Confirm to avoid changes to a domain
during migration (esp. between Begin and Perform phases). This change is
automatically applied to p2p and tunneled migrations. For normal
migration, this requires support from a client. In other words, if an
old (pre 0.9.4) client starts normal migration of a domain, the domain
will not be protected against changes between Begin and Perform steps.
When an operation started by virDomainBlockPull completes (either with
success or with failure), raise an event to indicate the final status.
This API allow users to avoid polling on virDomainGetBlockJobInfo if
they would prefer to use an event mechanism.
* daemon/remote.c: Dispatch events to client
* include/libvirt/libvirt.h.in: Define event ID and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Extend API to handle the new event
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
for block_stream completion and emit a libvirt block pull event
* src/remote/remote_driver.c: Receive and dispatch events to application
* src/remote/remote_protocol.x: Wire protocol definition for the event
* src/remote_protocol-structs: structure definitions for protocol verification
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c: Watch for BLOCK_STREAM_COMPLETED event
from QEMU monitor
Set up the types for the block pull functions and insert them into the
virDriver structure definition. Symbols are exported in this patch to
prevent
documentation compile failures.
* include/libvirt/libvirt.h.in: new API
* src/driver.h: add the new entry to the driver structure
* python/generator.py: fix compiler errors, the actual python bindings
* are
implemented later
* src/libvirt_public.syms: export symbols
* docs/apibuild.py: Extend 'unsigned long' parameter exception to this
* API
Modifying the xml on either save or restore only gets you so
far - you have to remember to 'virsh dumpxml dom' just prior
to the 'virsh save' in order to have an xml file worth modifying
that won't be rejected due to abi breaks. To make this more
powerful, we need a way to grab the xml embedded within a state
file, and from there, it's not much harder to also support
modifying a state file in-place.
Also, virDomainGetXMLDesc didn't document its flags.
* include/libvirt/libvirt.h.in (virDomainSaveImageGetXMLDesc)
(virDomainSaveImageDefineXML): New prototypes.
* src/libvirt.c (virDomainSaveImageGetXMLDesc)
(virDomainSaveImageDefineXML): New API.
* src/libvirt_public.syms: Export them.
* src/driver.h (virDrvDomainSaveImageGetXMLDesc)
(virDrvDomainSaveImgeDefineXML): New driver callbacks.
VIR_ERR_INVALID_ARG implies that an argument cannot possibly
be correct, given the current state of the API.
VIR_ERR_CONFIG_UNSUPPORTED implies that a configuration is
wrong, but arguments aren't configuration.
VIR_ERR_NO_SUPPORT implies that a function is completely
unimplemented.
But in the case of a function that is partially implemented,
yet the full power of the API is not available for that
driver, none of the above messages make sense. Hence a new
error message, implying that the argument is known to comply
with the current state of the API, and that while the driver
supports aspects of the function, it does not support that
particular use of the argument.
A good use case for this is a driver that supports
virDomainSaveFlags, but not the dxml argument of that API.
It might be feasible to also use this new error for all functions
that check flags, and which accept fewer flags than what is possible
in the public API. But doing so would get complicated, since
neither libvirt.c nor the remote driver may do flag filtering,
and every other driver would have to do a two-part check, first
using virCheckFlags on all public flags (which gives
VIR_ERR_INVALID_ARG for an impossible flag), followed by a
particular mask check for VIR_ERR_ARGUMENT_UNSUPPORTED (for a
possible public flag but unsupported by this driver).
* include/libvirt/virterror.h (VIR_ERR_ARGUMENT_UNSUPPORTED): New
error.
* src/util/virterror.c (virErrorMsg): Give it a message.
Suggested by Daniel P. Berrange.
This introduces new API virDomainDestroyFlags to allow
domain destroying with flags, as the existing API virDomainDestroy
misses flags.
The set of flags is defined in virDomainDestroyFlagsValues enum,
which is currently commented, because it is empty.
Calling this API with no flags set (@flags == 0) is equivalent calling
virDomainDestroy.
In order to choose whether to use O_DIRECT when saving a domain image
to a file, we need a new flag. But virDomainSave was implemented
before our policy of all new APIs having a flag argument. Likewise
for virDomainRestore when restoring from a file.
The new flag name is chosen as CACHE_BYPASS so as not to preclude
a future solution that uses posix_fadvise once the Linux kernel has
a smarter implementation of that interface.
* include/libvirt/libvirt.h.in (virDomainCreateFlags)
(virDomainCoreDumpFlags): Add a flag.
(virDomainSaveFlags, virDomainRestoreFlags): New prototypes.
* src/libvirt.c (virDomainSaveFlags, virDomainRestoreFlags): New API.
* src/libvirt_public.syms: Export them.
* src/driver.h (virDrvDomainSaveFlags, virDrvDomainRestoreFlags):
New driver callbacks.
Add virtkey lib for usage-improvment and keycode translating.
Add 4 internal API for the aim
const char *virKeycodeSetTypeToString(int codeset);
int virKeycodeSetTypeFromString(const char *name);
int virKeycodeValueFromString(virKeycodeSet codeset, const char *keyname);
int virKeycodeValueTranslate(virKeycodeSet from_codeset,
virKeycodeSet to_offset,
int key_value);
* include/libvirt/libvirt.h.in: extend virKeycodeSet enum
* src/Makefile.am: add new virtkeycode module and rule to generate
virkeymaps.h
* src/util/virkeycode.c src/util/virkeycode.h: new module
* src/util/virkeycode-mapgen.py: python generator for virkeymaps.h
out of keymaps.csv
* src/libvirt_private.syms: extend private symbols for new module
* .gitignore: add generated virkeymaps.h
This introduces a new API virDomainUndefineFlags to control the
domain undefine process, as the existing API virDomainUndefine
doesn't support flags.
Currently only flag VIR_DOMAIN_UNDEFINE_MANAGED_SAVE is supported.
If the domain has a managed save image, including
VIR_DOMAIN_UNDEFINE_MANAGED_SAVE in @flags will also remove that
file, and omitting the flag will cause undefine process to fail.
This patch also changes the behavior of virDomainUndefine, if the
domain has a managed save image, the undefine will be refused.
This patch extends virDomainSetVcpusFlags API to support
VIR_DOMAIN_AFFECT_CURRENT flag.
Now because most APIs accept VIR_DOMAIN_AFFECT_CURRENT flags,
virDomainSetVcpusFlags API should also do.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Introduce a new API in libvirt-qemu.so
virDomainPtr virDomainQemuAttach(virConnectPtr domain,
unsigned long long pid,
unsigned int flags);
This allows libvirtd to attach to an existing, externally
launched QEMU process. This is useful for QEMU developers who
prefer to launch QEMU themselves for debugging/devel reasons,
but still want the benefit of libvirt based tools like
virt-top, virt-viewer, etc
* include/libvirt/libvirt-qemu.h: Define virDomainQemuAttach
* src/driver.h, src/libvirt-qemu.c, src/libvirt_qemu.syms:
Driver glue for virDomainQemuAttach
Most APIs use 'unsigned int flags'; but a few stragglers were using
a signed value. In particular, the vir*GetXMLDesc APIs were
split-brain, with inconsistent choice of types. Although it is
an API break to use 'int' instead of 'unsigned int', it is ABI
compatible (pre-compiled apps will have no difference in behavior),
and generally apps can be recompiled without any issue (only rare
apps that compiled with extremely high warning levels, or which
pass libvirt API around as typed function pointers, would have to
make any code changes to deal with the change).
The migrate APIs use 'unsigned long flags', which can't be changed,
due to ABI constraints.
This patch intentionally touches only the public API, to prove the
claim that most existing code (including driver callbacks and virsh)
still compiles just fine in spite of the type change.
* include/libvirt/libvirt.h.in (virConnectOpenAuth)
(virDomainCoreDump, virDomainGetXMLDesc, virNetworkGetXMLDesc)
(virNWFilterGetXMLDesc): Use unsigned int for flags.
(virDomainHasCurrentSnapshot): Use consistent spelling.
* src/libvirt.c (virConnectOpenAuth, virDomainCoreDump)
(virDomainGetXMLDesc, virNetworkGetXMLDesc)
(virNWFilterGetXMLDesc, do_open): Update accordingly.
We already have a public virDomainPinVcpu, which implies that
Pin and Vcpu are treated as separate words. Unreleased commit
e261987c introduced virDomainGetVcpupinInfo as the first public
API that used Vcpupin, although we had prior internal uses of
that spelling. For consistency, change the spelling to be two
words everywhere, regardless of whether pin comes first or last.
* daemon/remote.c: Treat vcpu and pin as separate words.
* include/libvirt/libvirt.h.in: Likewise.
* src/conf/domain_conf.c: Likewise.
* src/conf/domain_conf.h: Likewise.
* src/driver.h: Likewise.
* src/libvirt.c: Likewise.
* src/libvirt_private.syms: Likewise.
* src/libvirt_public.syms: Likewise.
* src/libxl/libxl_driver.c: Likewise.
* src/qemu/qemu_driver.c: Likewise.
* src/remote/remote_driver.c: Likewise.
* src/xen/xend_internal.c: Likewise.
* tools/virsh.c: Likewise.
* src/remote/remote_protocol.x: Likewise.
* src/remote_protocol-structs: Likewise.
Suggested by Matthias Bolte.
This patch introduces a new libvirt API (virDomainGetVcpupinInfo),
as a counterpart to virDomainPinVcpuFlags.
We can use virDomainGetVcpus API to retrieve CPU affinity information,
but can't use this API against inactive domains (at least in case of KVM),
as it lacks a flags parameter.
The usual thing is to add a new virDomainGetVcpusFlags, but that API name
is already occupied by the counterpart to virDomainGetMaxVcpus, which
has a completely different signature.
The virDomainGetVcpupinInfo is the new API to retrieve CPU affinity
information of active and inactive domains. While the usual convention
is to list an array before its length, this API violates that rule
in order to be more like virDomainGetVcpus (where maxinfo was doing
double-duty as the length of two different arrays).
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
If an application is using libvirt + KVM as a piece of its
internal infrastructure to perform a specific task, it can
be desirable to guarentee the VM dies when the virConnectPtr
disconnects from libvirtd. This ensures the app can't leak
any VMs it was using. Adding VIR_DOMAIN_START_AUTOKILL as
a flag when starting guests enables this to be done.
* include/libvirt/libvirt.h.in: All VIR_DOMAIN_START_AUTOKILL
* src/qemu/qemu_driver.c: Support automatic killing of guests
upon connection close
* tools/virsh.c: Add --autokill flag to 'start' and 'create'
commands
Since we virEventRegisterDefaultImpl is now a public API, callers need
a way to invoke the default registered Handle and Timeout functions. We
already have general functions for these internally, so promote
them to the public API.
v2:
Actually add APIs to libvirt.h
Even though rpc uses 'unsigned int' for the _len parameter that
passes the length of item<length>, the public libvirt APIs all
use 'int' and filter out lengths < 0, except for virDomainSendKey.
* include/libvirt/libvirt.h.in (virDomainSendKey): All other APIs
use int for array length.
* src/libvirt.c (virDomainSendKey): Adjust.
* src/driver.h (virDrvDomainSendKey): Likewise.
* daemon/remote_generator.pl: Likewise.
When an operation started by virDomainBlockPullAll completes (either with
success or with failure), raise an event to indicate the final status. This
allows an API user to avoid polling on virDomainBlockPullInfo if they would
prefer to use the event mechanism.
* daemon/remote.c: Dispatch events to client
* include/libvirt/libvirt.h.in: Define event ID and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Extend API to handle the new event
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
for block_stream completion and emit a libvirt block pull event
* src/remote/remote_driver.c: Receive and dispatch events to application
* src/remote/remote_protocol.x: Wire protocol definition for the event
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c: Watch for BLOCK_STREAM_COMPLETED event
from QEMU monitor
Signed-off-by: Adam Litke <agl@us.ibm.com>
Set up the types for the block pull functions and insert them into the
virDriver structure definition. Symbols are exported in this patch to prevent
documentation compile failures.
* include/libvirt/libvirt.h.in: new API
* src/driver.h: add the new entry to the driver structure
* python/generator.py: fix compiler errors, the actual python bindings are
implemented later
* src/libvirt_public.syms: export symbols
Signed-off-by: Adam Litke <agl@us.ibm.com>
Add public virDomainSendKey() and enum libvirt_keycode_set
for the @codeset.
Python version of virDomainSendKey() has not been implemented yet,
it will be done soon.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Qemu once supported following memory stats which will returned by
"query_balloon":
stat_put(dict, "actual", actual);
stat_put(dict, "mem_swapped_in", dev->stats[VIRTIO_BALLOON_S_SWAP_IN]);
stat_put(dict, "mem_swapped_out", dev->stats[VIRTIO_BALLOON_S_SWAP_OUT]);
stat_put(dict, "major_page_faults", dev->stats[VIRTIO_BALLOON_S_MAJFLT]);
stat_put(dict, "minor_page_faults", dev->stats[VIRTIO_BALLOON_S_MINFLT]);
stat_put(dict, "free_mem", dev->stats[VIRTIO_BALLOON_S_MEMFREE]);
stat_put(dict, "total_mem", dev->stats[VIRTIO_BALLOON_S_MEMTOT]);
But it later disabled all the stats except "actual" by commit
07b0403dfc2b2ac179ae5b48105096cc2d03375a.
libvirt doesn't parse "actual", so user will always see a empty result
with "virsh dommemstat $domain". Even qemu haven't disabled the stats,
we should support parsing "actual".
This patch deprecates following enums:
VIR_DOMAIN_MEM_CURRENT
VIR_DOMAIN_MEM_LIVE
VIR_DOMAIN_MEM_CONFIG
VIR_DOMAIN_VCPU_LIVE
VIR_DOMAIN_VCPU_CONFIG
VIR_DOMAIN_DEVICE_MODIFY_CURRENT
VIR_DOMAIN_DEVICE_MODIFY_LIVE
VIR_DOMAIN_DEVICE_MODIFY_CONFIG
And modify internal codes to use virDomainModificationImpact.
This commit is safe precisely because there has been no release
for any of the enum values being deleted (they were added post-0.9.1).
After the 0.9.2 release, we can then take advantage of
virDomainModificationImpact in more places.
* include/libvirt/libvirt.h.in (virDomainModificationImpact): New
enum.
(virDomainSchedParameterFlags, virMemoryParamFlags): Delete, since
these were never released, and the new enum works fine here.
* src/libvirt.c (virDomainGetMemoryParameters)
(virDomainSetMemoryParameters)
(virDomainGetSchedulerParametersFlags)
(virDomainSetSchedulerParametersFlags): Update documentation.
* src/qemu/qemu_driver.c (qemuDomainSetMemoryParameters)
(qemuDomainGetMemoryParameters, qemuSetSchedulerParametersFlags)
(qemuSetSchedulerParameters, qemuGetSchedulerParametersFlags)
(qemuGetSchedulerParameters): Adjust clients.
* tools/virsh.c (cmdSchedinfo, cmdMemtune): Likewise.
Based on ideas by Daniel Veillard and Hu Tao.
Define the basic framework lock manager plugins. The
basic plugin API for 3rd parties to implemented is
defined in
src/locking/lock_driver.h
This allows dlopen()able modules for alternative locking
schemes, however, we do not install the header. This
requires lock plugins to be in-tree allowing changing of
the lock manager plugin API in future.
The libvirt code for loading & calling into plugins
is in
src/locking/lock_manager.{c,h}
* include/libvirt/virterror.h, src/util/virterror.c: Add
VIR_FROM_LOCKING
* src/locking/lock_driver.h: API for lock driver plugins
to implement
* src/locking/lock_manager.c, src/locking/lock_manager.h:
Internal API for managing locking
* src/Makefile.am: Add locking code
This introduces a new domain
VIR_DOMAIN_EVENT_ID_CONTROL_ERROR
Which uses the existing generic callback
typedef void (*virConnectDomainEventGenericCallback)(virConnectPtr conn,
virDomainPtr dom,
void *opaque);
This event is intended to be emitted when there is a failure in
some part of the domain virtualization system. Whether the domain
continues to run/exist after the failure is an implementation
detail specific to the hypervisor.
The idea is that with some types of failure, hypervisors may
prefer to leave the domain running in a "degraded" mode of
operation. For example, if something goes wrong with the QEMU
monitor, it is possible to leave the guest OS running quite
happily. The mgmt app will simply loose the ability todo various
tasks. The mgmt app can then choose how/when to deal with the
failure that occured.
* daemon/remote.c: Dispatch of new event
* examples/domain-events/events-c/event-test.c: Demo catch
of event
* include/libvirt/libvirt.h.in: Define event ID and callback
* src/conf/domain_event.c, src/conf/domain_event.h: Internal
event handling
* src/remote/remote_driver.c: Receipt of new event from daemon
* src/remote/remote_protocol.x: Wire protocol for new event
* src/remote_protocol-structs: add new event for checks
If we can choose live or config when setting, then we need to
be able to choose which one we are querying.
Also, make the documentation clear that set must use a non-empty
subset (some of the hypervisors fail if params is NULL).
* include/libvirt/libvirt.h.in
(virDomainGetSchedulerParametersFlags): New prototype.
* src/libvirt.c (virDomainGetSchedulerParametersFlags): Implement
it.
* src/libvirt_public.syms: Export it.
* python/generator.py (skip_impl): Don't auto-generate.
* src/driver.h (virDrvDomainGetSchedulerParametersFlags): New
callback.
Commit 824dcaff was a regression (thankfully unreleased) for any
client code that used 'struct _virSchedParameter' directly rather
than the preferred virSchedParameter typedef. Adding a #define
avoids even that API change, while rearranging the file makes it
clear what the old vs. new API is.
* include/libvirt/libvirt.h.in: Rearrange older names to the
bottom and improve documentation on preferred names.
(virDomainGetSchedulerParameters, virDomainSetSchedulerParameters)
(virDomainSetSchedulerParametersFlags)
(virDomainSetBlkioParameters, virDomainGetBlkioParameters)
(virDomainSetMemoryParameters, virDomainGetMemoryParameters):
Use newer type names.
* python/libvirt-override.c: Adjust code generation to cope.
Suggested by Daniel P. Berrange.
This is the API agreed on in:
https://www.redhat.com/archives/libvir-list/2011-May/msg00026.html
(with a slight name change to use "...begin" rather than
"...start"). This implements transactional changes to the host network
config. When a transaction is begun with ncf_change_begin(), all other
netcf APIs will continue to work as they always have, but a snapshot
of the existing config will be taken, allowing reversion (rollback,
using ncf_change_rollback()) to the exact state of config at the time
ncf_change_begin() was called. Alternately, if it's determined that
the new changes are acceptable, ncf_change_commit() can be called,
which will eliminate the snapshot and make the changes permanent.
As a failsafe measure, if neither ncf_change_commit() or
ncf_change_rollback() is called by the next time the system reboots,
the netcf-transaction initscript will be automatically called to
rollback the changes.
The new flags allow to pick current state, config or the live
parameter, with current being the existing API default (0).
This also hooks this to --config, --live, --current parameters for
the memtune virsh command
* include/libvirt/libvirt.h.in: defines the new flags
* tools/virsh.c: adds support at virsh level
* tools/virsh.pod: updates virsh documentation
There are two pieces of information which are desirable for
migration, which cannot be supplied by applications
- The explicit QEMU migration URI, while using Peer2Peer
migration
- An override for the target VM XML
This introduces two new public APIs to support these extra
parameters. There is no need for extra wire protocool changes,
since this is supported by the v3 migration enhancements
* include/libvirt/libvirt.h.in,
src/libvirt.c, src/libvirt_public.syms: Add virDomainMigrate2
and virDomainMigrateToURI2
The new type is identical to the three old types that it replaces,
and by creating a common type, this allows future patches to share
common code that manipulates typed parameters.
This change is backwards-compatible in API (recompilation works
without any edits) and ABI (an older client that has not been
recompiled uses the same layout) for code using only public
names; only code using private names (those beginning with _)
will have to adapt.
* include/libvirt/libvirt.h.in (virTypedParameterType)
(VIR_TYPED_PARAM_FIELD_LENGTH, _virTypedParameter): New enum,
macro, and type.
(virSchedParameter, virBlkioParameter, virMemoryParameter):
Rewrite in terms of a common type, while keeping all old public
names for backwards compatibility.
(struct _virSchedParameter, struct _virBlkioParameter)
(struct _virMemoryParameter): Delete - these are private names.
* python/generator.py (enum): Cope with the refactoring.
Add public API for taking screenshots of current domain console.
* include/libvirt/libvirt.h.in: add virDomainScreenshot
* src/libvirt_public.syms: Export new symbol
This patch introduces VIR_DOMAIN_MEM_CURRENT flag and
modifies virDomainSetMemoryFlags function to support it.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
New APIs are added allowing streaming of content to/from
storage volumes.
* include/libvirt/libvirt.h.in: Add virStorageVolUpload and
virStorageVolDownload APIs
* src/driver.h, src/libvirt.c, src/libvirt_public.syms: Stub
code for new APIs
* src/storage/storage_driver.c, src/esx/esx_storage_driver.c:
Add dummy entries in driver table for new APIs
The Open Nebula driver has been unmaintained since it was first
introduced. The only commits have been for tree-wide cleanups.
It also has a major design flaw, in that it only knows about guests
that it has created itself, which makes it of very limited use.
Discussions wrt evolution of the VMWare ESX driver, concluded that
it should limit itself to single-node ESX operation and not try to
manage the multi-node architecture of VirtualCenter. Open Nebula
is a cluster like Virtual Center, not a single node system, so
the same reasoning applies.
The DeltaCloud project includes an Open Nebula driver and is a much
better fit architecturally, since it is explicitly targetting the
distributed multihost cluster scenario.
Thus this patch deletes the libvirt Open Nebula driver with the
recommendation that people use DeltaCloud for managing it instead.
* configure.ac: Remove probe for xmlrpc & --with-one arg
* daemon/Makefile.am, daemon/libvirtd.c, src/Makefile.am: Remove
ONE driver build
* src/opennebula/one_client.c, src/opennebula/one_client.h,
src/opennebula/one_conf.c, src/opennebula/one_conf.h,
src/opennebula/one_driver.c, src/opennebula/one_driver.c: Delete
files
* autobuild.sh, libvirt.spec.in, mingw32-libvirt.spec.in: Remove
build rules for Open Nebula
* docs/drivers.html.in, docs/sitemap.html.in: Remove reference
to OpenNebula
* docs/drvone.html.in: Delete file
It is possible to set a migration speed limit when starting
migration. This new API allows the speed limit to be changed
on the fly to adjust to changing conditions
* src/driver.h, src/libvirt.c, src/libvirt_public.syms,
include/libvirt/libvirt.h.in: Add virDomainMigrateSetMaxSpeed
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/vmware/vmware_driver.c, src/xen/xen_driver.c,
src/libxl/libxl_driver.c: Stub new API
Add a new xen driver based on libxenlight [1], which is the primary
toolstack starting with Xen 4.1.0. The driver is stateful and runs
privileged only.
Like the existing xen-unified driver, the libxenlight driver is
accessed with xen:// URI. Driver selection is based on the status
of xend. If xend is running, the libxenlight driver will not load
and xen:// connections are handled by xen-unified. If xend is not
running *and* the libxenlight driver is available, xen://
connections are deferred to the libxenlight driver.
V6:
- Address several code style issues noted by Daniel Veillard
- Make drive work with xen:/// URI
- Hold domain object reference while domain is injected in
libvirt event loop. Race found and fixed by Markus Groß.
V5:
- Ensure events are unregistered when domain private data
is destroyed. Discovered and fixed by Markus Groß.
V4:
- Handle restart of libvirtd, reconnecting to previously
started domains
- Rebased to current master
- Tested against Xen 4.1 RC7-pre (c/s 22961:c5d121fd35c0)
V3:
- Reserve vnc port within driver when autoport=yes
V2:
- Update to Xen 4.1 RC6-pre (c/s 22940:5a4710640f81)
- Rebased to current master
- Plug memory leaks found by Stefano Stabellini and valgrind
- Handle SHUTDOWN_crash domain death event
[1] http://lists.xensource.com/archives/html/xen-devel/2009-11/msg00436.html
* Correct the documentation for cgroup: the swap_hard_limit indicates
mem+swap_hard_limit.
* Change cgroup private apis to: virCgroupGet/SetMemSwapHardLimit
Signed-off-by: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED uses INT64_MAX but stdint.h
was not and should not be included. Therefore, libvirt.h was
not self-contained.
Instead of including stdint.h specify the value directly.
This patch introduces a new libvirt API (virDomainSetMemoryFlags) and
a flag (virDomainMemoryModFlags).
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Not all applications have an existing event loop they need
to integrate with. Forcing them to implement the libvirt
event loop integration APIs is an undue burden. This just
exposes our simple poll() based implementation for apps
to use. So instead of calling
virEventRegister(....callbacks...)
The app would call
virEventRegisterDefaultImpl()
And then have a thread somewhere calling
static bool quit = false;
....
while (!quit)
virEventRunDefaultImpl()
* daemon/libvirtd.c, tools/console.c,
tools/virsh.c: Convert to public event loop APIs
* include/libvirt/libvirt.h.in, src/libvirt_private.syms: Add
virEventRegisterDefaultImpl and virEventRunDefaultImpl
* src/util/event.c: Implement virEventRegisterDefaultImpl
and virEventRunDefaultImpl using poll() event loop
* src/util/event_poll.c: Add full error reporting
* src/util/virterror.c, include/libvirt/virterror.h: Add
VIR_FROM_EVENTS
The new virConnectGetSysinfo() API allows one to get the system
information associated to a connection host, providing the same
data as a guest that uses <os><smbios mode='host'/></os>, and in
a format that can be pasted into the guest and edited when using
<os><smbios mode='sysinfo'/></os>.
* include/libvirt/libvirt.h.in (virConnectGetSysinfo): Declare.
* src/libvirt_public.syms: Export new symbol.
Currently users who want to use virDomainQemuMonitorCommand() API or
it's virsh equivalent has to use the same protocol as libvirt uses for
communication to qemu. Since the protocol is QMP with current qemu and
HMP much more usable for humans, one ends up typing something like the
following:
virsh qemu-monitor-command DOM \
'{"execute":"human-monitor-command","arguments":{"command-line":"info kvm"}}'
which is not a very convenient way of debugging qemu.
This patch introduces --hmp option to qemu-monitor-command, which says
that the provided command is in HMP. If libvirt uses QMP to talk with
qemu, the command will automatically be converted into QMP. So the
example above is simplified to just
virsh qemu-monitor-command --hmp DOM "info kvm"
Also the result is converted from
{"return":"kvm support: enabled\r\n"}
to just plain HMP:
kvm support: enabled
If libvirt talks to qemu in HMP, --hmp flag is obviously a noop.
Display or set unlimited values for memory parameters. Unlimited is
represented by INT64_MAX in memory cgroup.
Signed-off-by: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Reported-by: Justin Clift <jclift@redhat.com>
Fix glitch in commit cddd2a06 (thankfully post-0.8.6, so no
released version has the glitch).
Document and try to workaround glitch in commit 46e9b0f (in 0.8.0),
which invalidated 6 virErrorNumber values dating as far back as 0.7.1.
My audit did not find any other glitches until pre-0.1.0 days. I'm
not sure how to add a syntax-check off the top of my head, but
hopefully the explicit numbering will make people think twice about
renumbering in the future.
* include/libvirt/virterror.h (virErrorDomain): Avoid inserting
new values in the middle, and add explicit numbering to help avoid
this in the future.
(virErrorNumber): Add explicit numbering, and document the snafu.
* src/remote/remote_driver.c (remoteIO): Compensate for the snafu.
The nodeinfo structure includes
nodes : the number of NUMA cell, 1 for uniform mem access
sockets : number of CPU socket per node
cores : number of core per socket
threads : number of threads per core
which does not work well for NUMA topologies where each node does not
consist of integral number of CPU sockets.
We also have VIR_NODEINFO_MAXCPUS macro in public libvirt.h which
computes maximum number of CPUs as (nodes * sockets * cores * threads).
As a result, we can't just change sockets to report total number of
sockets instead of sockets per node. This would probably be the easiest
since I doubt anyone is using the field directly. But because of the
macro, some apps might be using sockets indirectly.
This patch leaves sockets to be the number of CPU sockets per node (and
fixes qemu driver to comply with this) on machines where sockets can be
divided by nodes. If we can't divide sockets by nodes, we behave as if
there was just one NUMA node containing all sockets. Apps interested in
NUMA should consult capabilities XML, which is what they probably do
anyway.
This way, the only case in which apps that care about NUMA may break is
on machines with funky NUMA topology. And there is a chance libvirt
wasn't able to start any guests on those machines anyway (although it
depends on the topology, total number of CPUs and kernel version).
Nothing changes at all for apps that don't care about NUMA.
introduce new public API "virDomainIsUpdated"
* src/conf/domain_conf.h (new member "updated" for "virDomainObj")
* src/libvirt_public.syms
* include/libvirt/libvirt.h.in
To avoid the need for duplicating implementations of virStream
drivers, provide a generic implementation that can handle any
FD based stream. This code is copied from the existing impl
in the QEMU driver, with the locking moved into the stream
impl, and addition of a read callback
The FD stream code will refuse to operate on regular files or
block devices, since those can't report EAGAIN properly when
they would block on I/O
* include/libvirt/virterror.h, include/libvirt/virterror.h: Add
VIR_FROM_STREAM error domain
* src/qemu/qemu_driver.c: Remove code obsoleted by the new
generic streams driver.
* src/fdstream.h, src/fdstream.c, src/fdstream.c,
src/libvirt_private.syms: Generic reusable FD based streams
To enable virsh console (or equivalent) to be used remotely
it is necessary to provide remote access to the /dev/pts/XXX
pseudo-TTY associated with the console/serial/parallel device
in the guest. The virStream API provide a bi-directional I/O
stream capability that can be used for this purpose. This
patch thus introduces a virDomainOpenConsole API that uses
the stream APIs.
* src/libvirt.c, src/libvirt_public.syms,
include/libvirt/libvirt.h.in, src/driver.h: Define the
new virDomainOpenConsole API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c, src/xenapi/xenapi_driver.c: Stub
API entry point
QEMU allows forcing a CDROM eject even if the guest has locked the device.
Expose this via a new UpdateDevice flag, VIR_DOMAIN_DEVICE_MODIFY_FORCE.
This has been requested for RHEV:
https://bugzilla.redhat.com/show_bug.cgi?id=626305
v2: Change flag name, bool cleanups
Move existing routines about virSysinfoDef to an util module,
add a new entry point virSysinfoRead() to read the host values
with dmidecode
* src/conf/domain_conf.c src/conf/domain_conf.h src/util/sysinfo.c
src/util/sysinfo.h: move to a new module, add virSysinfoRead()
* src/Makefile.am: handle the new module build
* src/libvirt_private.syms: new internal symbols
* include/libvirt/virterror.h src/util/virterror.c: defined a new
error code for that module
* po/POTFILES.in: add new file for translations
Integrate with libaudit.so for auditing of important operations.
libvirtd gains a couple of config entries for auditing. By
default it will enable auditing, if its enabled on the host.
It can be configured to force exit if auditing is disabled
on the host. It will can also send audit messages via libvirt
internal logging API
Places requiring audit reporting can use the VIR_AUDIT
macro to report data. This is a no-op unless auditing is
enabled
* autobuild.sh, mingw32-libvirt.spec.in: Disable audit
on mingw
* configure.ac: Add check for libaudit
* daemon/libvirtd.aug, daemon/libvirtd.conf,
daemon/test_libvirtd.aug, daemon/libvirtd.c: Add config
options to enable auditing
* include/libvirt/virterror.h, src/util/virterror.c: Add
VIR_FROM_AUDIT source
* libvirt.spec.in: Enable audit
* src/util/virtaudit.h, src/util/virtaudit.c: Simple internal
API for auditing messages
API agreed on in
https://www.redhat.com/archives/libvir-list/2010-September/msg00456.html,
but modified for enum names to be consistent with virDomainDeviceModifyFlags.
* include/libvirt/libvirt.h.in (virDomainVcpuFlags)
(virDomainSetVcpusFlags, virDomainGetVcpusFlags): New
declarations.
* src/libvirt_public.syms: Export new symbols.
* include/libvirt/libvirt.h.in: some of the function type description
were broken so they could not be automatically documented
* src/util/event.c docs/apibuild.py: event.c exports one public API
so it needs to be scanned too, avoid a few warnings
Add proper documentation to the new VIR_DOMAIN_MEMORY_* macros in
libvirt.h.in to placate apibuild.py.
Mark args as unused in for libvirt_virDomain{Get,Set}MemoryParameters
in the Python bindings and add both to the libvirtMethods array.
Update remote_protocol-structs to placate make syntax-check.
Undo unintended modifications in vboxDomainGetInfo.
Update the function table of the VirtualBox and XenAPI drivers.
This patch adds a structure virMemoryParameter, it contains the name of
the
parameter and the type of the parameter along with a union.
dv:
+ rename enums to VIR_DOMAIN_MEMORY_PARAM_*
+ remove some extraneous tabs
v4:
+ Add unsigned int flags to the public api for future extensions
v3:
+ Protoype for virDomainGetMemoryParameters and dummy python binding.
v2:
+ Includes dummy python bindings for the library to build cleanly.
+ Define string constants like "hard_limit", etc.
+ re-order this patch.
After the recent libvirt-qemu library addition, VPATH builds fail with:
CC libvirt_qemu_la-libvirt-qemu.lo
In file included from ../../src/libvirt-qemu.c:29:
../../include/libvirt/libvirt-qemu.h:17:22: error: libvirt.h: No such file or directory
...
CCLD libvirt-qmeu.la
/usr/bin/ld: cannot open linker script file libvirt_qemu.syms: No such file or directory
This fixes both issues (there are still some documentation VPATH issues,
but those don't show up with 'make check').
* configure.ac (LIBVIRT_QEMU_SYMBOL_FILE): While libvirt.syms is
generated and lives in $(builddir), libvirt_qemu.syms is static
and lives in $(srcdir).
* include/libvirt/libvirt-qemu.h (includes): Pull in libvirt.h via
the public location, since this is a public header.
Add the library entry point for the new virDomainQemuMonitorCommand()
entry point. Because this is not part of the "normal" libvirt API,
it gets its own header file, library file, and will eventually
get its own over-the-wire protocol later in the series.
Changes since v1:
- Go back to using the virDriver table for qemuDomainMonitorCommand, due to
linking issues
- Added versioning information to the libvirt-qemu.so
Changes since v2:
- None
Changes since v3:
- Add LGPL header to libvirt-qemu.c
- Make virLibConnError and virLibDomainError macros instead of function calls
Changes since v4:
- Move exported symbols to libvirt_qemu.syms
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Unfortunately the NWFilter functions were outside of the
"extern C { ... }" declaration in include/libvirt/libvirt.h.in,
which means that they couldn't be properly used with C++. Move
them inside of the braces, which should fix the problem.
Signed-off-by: Chris Lalancette <clalance@redhat.com>
Support for live migration between hosts that do not share storage was
added to qemu-kvm release 0.12.1.
It supports two flags:
-b migration without shared storage with full disk copy
-i migration without shared storage with incremental copy (same base image
shared between source and destination).
I tested the live migration without shared storage (both flags) for native
and p2p with and without tunnelling. I also verified that the fix doesn't
affect normal migration with shared storage.
This introduces a new event type
VIR_DOMAIN_EVENT_ID_IO_ERROR_REASON
This event is the same as the previous VIR_DOMAIN_ID_IO_ERROR
event, but also includes a string describing the cause of
the event.
Thus there is a new callback definition for this event type
typedef void (*virConnectDomainEventIOErrorReasonCallback)(virConnectPtr conn,
virDomainPtr dom,
const char *srcPath,
const char *devAlias,
int action,
const char *reason,
void *opaque);
This is currently wired up to the QEMU block IO error events
* daemon/remote.c: Dispatch IO error events to client
* examples/domain-events/events-c/event-test.c: Watch for
IO error events
* include/libvirt/libvirt.h.in: Define new IO error event ID
and callback signature
* src/conf/domain_event.c, src/conf/domain_event.h,
src/libvirt_private.syms: Extend API to handle IO error events
* src/qemu/qemu_driver.c: Connect to the QEMU monitor event
for block IO errors and emit a libvirt IO error event
* src/remote/remote_driver.c: Receive and dispatch IO error
events to application
* src/remote/remote_protocol.x: Wire protocol definition for
IO error events
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c: Watch for BLOCK_IO_ERROR event
from QEMU monitor
Some applications need to be able to query a guest's disk info,
even for paths not managed by the storage pool APIs. This adds
a very simple API to get this information, modelled on the
virStorageVolGetInfo API, but with an extra field 'physical'.
Normally 'physical' and 'allocation' will be identical, but
in the case of a qcow2-like file stored inside a block device
'physical' will give the block device size, while 'allocation'
will give the qcow2 image size
* include/libvirt/libvirt.h.in: Define virDomainGetBlockInfo
virDomainManagedSave() is to be run on a running domain. Once the call
complete, as in virDomainSave() the domain is stopped upon completion,
but there is no restore counterpart as any order to start the domain
from the API would load the state from the managed file, similary if
the domain is autostarted when libvirtd starts.
Once a domain has restarted his managed save image is destroyed,
basically managed save image can only exist for a stopped domain,
for a running domain that would be by definition outdated data.
* include/libvirt/libvirt.h.in src/libvirt.c src/libvirt_public.syms:
adds the new entry points virDomainManagedSave(),
virDomainHasManagedSaveImage() and virDomainManagedSaveRemove()
* src/driver.h src/esx/esx_driver.c src/lxc/lxc_driver.c
src/opennebula/one_driver.c src/openvz/openvz_driver.c
src/phyp/phyp_driver.c src/qemu/qemu_driver.c src/vbox/vbox_tmpl.c
src/remote/remote_driver.c src/test/test_driver.c src/uml/uml_driver.c
src/xen/xen_driver.c: add corresponding new internal drivers entry
points
When a watchdog/IO error occurs, one of the possible actions that
QEMU might take is to pause the guest. In this scenario libvirt
needs to update its internal state for the VM, and emit a
lifecycle event:
VIR_DOMAIN_EVENT_SUSPENDED
with a detail being one of:
VIR_DOMAIN_EVENT_SUSPENDED_IOERROR
VIR_DOMAIN_EVENT_SUSPENDED_WATCHDOG
To future proof against possible QEMU support for multiple monitor
consoles, this patch also hooks into the 'STOPPED' event in QEMU
and emits a generic VIR_DOMAIN_EVENT_SUSPENDED_PAUSED event
* include/libvirt/libvirt.h.in: Add VIR_DOMAIN_EVENT_SUSPENDED_IOERROR
* src/qemu/qemu_driver.c: Update VM state to paused when IO error
or watchdog events occurrs
* src/qemu/qemu_monitor_json.c: Fix typo in disk IO event name
This flag is used in migration prepare step to send updated XML
definition of a guest.
Also ``virsh dumpxml --update-cpu [--inactive] guest'' command can be
used to see the updated CPU requirements.
This patch adds the implementation of the public API for the network
filtering (ACL) extensions to libvirt.c .
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
This patch adds extensions to libvirt's public API necessary for
controlling the new functionality from remote for example.
Signed-off-by: Stefan Berger <stefanb@us.ibm.com>
The current virDomainAttachDevice API can be (ab)used to change
the media of an existing CDROM/Floppy device. Going forward there
will be more devices that can be configured on the fly and overloading
virDomainAttachDevice for this is not too pleasant. This patch adds
a new virDomainUpdateDeviceFlags() explicitly just for modifying
existing devices.
* include/libvirt/libvirt.h.in: Add virDomainUpdateDeviceFlags
* src/driver.h: Internal API for virDomainUpdateDeviceFlags
* src/libvirt.c, src/libvirt_public.syms: Glue public API to
driver API
* src/esx/esx_driver.c, src/lxc/lxc_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c, src/uml/uml_driver.c,
src/vbox/vbox_tmpl.c, src/xen/xen_driver.c, src/xenapi/xenapi_driver.c: Add
stubs for new driver entry point
