The function only returns zero or aborts, so it might as well be void.
This has the added benefit of simplifying the code that calls it.
Signed-off-by: Matt Coleman <matt@datto.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Expose QEMU's 9pfs 'fmode' and 'dmode' options via attributes on the
'filesystem' node in the domain XML. These options control the creation
mode of files and directories, respectively, when using
accessmode=mapped.
Signed-off-by: Brian Turek <brian.turek@gmail.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
In v6.6.0-rc1~124 we've introduced a new mechanism for MAC
addresses for ESX: ignore all checks (type='static') that libvirt
or ESX would do (and possibly fail) for specified MAC address.
Accepted values for the @type attribute are "generated" and
"static". But the error message mentions a different attribute.
Fixes 454e5961ab
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1892130
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
It doesn't make much sense to configure the bucket count in the hash
table for each case specifically. Replace all calls of virHashCreate
with virHashNew which has a pre-set size and remove virHashCreate
completely.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
This patch adds new schema and adds support for parsing and formatting
domain configurations that include vdpa devices.
vDPA network devices allow high-performance networking in a virtual
machine by providing a wire-speed data path. These devices require a
vendor-specific host driver but the data path follows the virtio
specification.
When a device on the host is bound to an appropriate vendor-specific
driver, it will create a chardev on the host at e.g. /dev/vhost-vdpa-0.
That chardev path can then be used to define a new interface with
type='vdpa'.
Signed-off-by: Jonathon Jongsma <jjongsma@redhat.com>
Reviewed-by: Laine Stump <laine@redhat.com>
These XML attributes have been mandatory since the introduction of SEV
support to libvirt. This design decision was based on QEMU's
requirement for these to be mandatory for migration purposes, as
differences in these values across platforms must result in the
pre-migration checks failing (not that migration with SEV works at the
time of this patch).
Expecting the user to specify these is cumbersome and the same XML
cannot be re-used across different revisions of SEV. Since
we have SEV platform information saved in QEMU capabilities, we can
make the attributes optional and should fill them in automatically
in the QEMU driver right before starting it.
Resolves: https://gitlab.com/libvirt/libvirt/-/issues/57
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
In fee8a61d29 a new attribute to <memballoon/> was introduced:
free-page-reporting. We don't really like hyphens in attribute
names. Use camelCase instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
This will add the proper documentation and parser support for the free page
reporting feature that is introduced in QEMU 5.1.
Signed-off-by: Nico Pache <npache@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
This adds a new value to virConnectCompareCPUFlags,
"VIR_CONNECT_CPU_VALIDATE_XML", that governs XML document validation in
virCPUDefParseXML.
In src/conf/cpu_conf.c, include configmake.h for PKGDATADIR and
virfile.h for virFileFindResource.
Signed-off-by: Tim Wiederhake <twiederh@redhat.com>
Reviewed-by: Peter Krempa <pkrempa@redhat.com>
If we use g_new0 there's no need for the 'cleanup' label as there's
nothing to fail after the allocation.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
All these lines were moved over from the now-defunct
virDomainNetDefClear(), which required all pointers to be cleared
after free, but virDomainNetDefFree() doesn't have that restriction -
after free'ing the pointers are never again referenced, so g_free() is
safe.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
This function is no longer used anywhere except virDomainNetDefFree(),
so just inline its contents there.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Allow to match with CCW addresses in addition to PCI addresses
(and MAC addresses).
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Add an abort() on the class/object allocation failures so that
virStorageSourceNew() always returns a virStorageSource and remove
checks from all callers.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The alignment for the pSeries NVDIMM does not depend on runtime
constraints. This means that it can be done in device parse
time, instead of runtime, allowing the domain XML to reflect
what the auto-alignment would do when the domain starts.
This brings consistency between the NVDIMM size reported by the
domain XML and what the guest sees, without impacting existing
guests that are using an unaligned size - they'll work as usual,
but the domain XML will be updated with the actual size of the
NVDIMM.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
We'll use the auto-alignment function during parse time, in
domain_conf.c. Let's move the function to that file, renaming
it to virDomainNVDimmAlignSizePseries(). This will also make it
clearer that, although QEMU is the only driver that currently
supports it, pSeries NVDIMM restrictions aren't tied to QEMU.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Introduce 'isa' controller type. In domain XML it looks this way:
...
<controller type='isa' index='0'>
<address type='pci' domain='0x0000' bus='0x00' slot='0x01'
function='0x0'/>
</controller>
...
Currently, this is needed for the bhyve driver to allow choosing a
specific PCI address for that. In bhyve, this controller is used to
attach serial ports and a boot ROM.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The backend for the SCSI host device is a storage source. While the
definition doesn't look like that it's converted to a storage source
when the VM is running.
Add the storage source to the definition object and also parse/format
its private data which will be used for internal state storage while
the VM is running.
Note that the virStorageSourcePtr may not be allocated all the time so
the private data parser allocates it if there is any private data
present.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Use XPath instead of iterating through the nodes.
Few error messages were modified so that the parser can be written in a
simpler way.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Use XPath to get the host list instead of iterating through the nodes.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
There's just one caller for the function. Move the code into the caller.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
By default Xen only allows guests to write "known safe" values into PCI
configuration space, yet many devices require writes to other areas of
the configuration space in order to operate properly. To allow writing
any values Xen supports the 'permissive' setting, see xl.cfg(5) man page.
This change models Xen's permissive setting by adding a writeFiltering
attribute on the <source> element of a PCI hostdev. When writeFiltering
is set to 'no', the Xen permissive setting will be enabled and guests
will be able to write any values into the device's configuration space.
The permissive setting remains disabled in the absense of the
writeFiltering attribute, of if it is explicitly set to 'yes'.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
Signed-off-by: Simon Gaiser <simon@invisiblethingslab.com>
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Since the macro no longer includes the 'ignore_value'
statement, stop putting another empty statement after it.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Allow to map sound playback and recording devices to host devices
using "<audio type='oss'/>" OSS audio backend.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Introduce a new device element "<audio>" which allows
to map guest sound device specified using the "<sound>"
element to specific audio backend.
Example:
<sound model='ich7'>
<audio id='1'/>
</sound>
<audio id='1' type='oss'>
<input dev='/dev/dsp0'/>
<output dev='/dev/dsp0'/>
</audio>
This block maps to OSS audio backend on the host using
/dev/dsp0 device for both input (recording)
and output (playback).
OSS is the only backend supported so far.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Add 'ich7' sound model. This is a preparation for sound support in
bhyve, as 'ich7' is the only model it supports.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Back when macvtap support was added in commit 315baab944 in Feb. 2010
(libvirt-0.7.7), it was setup to autogenerate a name for the device if
one wasn't supplied, in the pattern "macvtap%d" (or "macvlan%d"),
similar to the way an unspecified standard tap device name will lead
to an autogenerated "vnet%d".
As a matter of fact, in commit ca1b7cc8e4 added in May 2010, the code
was changed to *always* ignore a supplied device name for macvtap
interfaces by deleting *any* name immediately during the <interface>
parsing (this was intended to prevent one domain which had failed to
completely start from deleting the macvtap device of another domain
which had subsequently been provided the same device name (this will
seem mildly ironic later). This was later fixed to only clear the
device name when inactive XML was being parsed. HOWEVER - this was
only done if the xml was <interface type='direct'> - autogenerated
names were not cleared for <interface type='network'> (which could
also result in a macvtap device).
Although the names of "vnetX" tap devices had always been
automatically cleared when parsing <interface> (see commit d1304583d
from July 2008 (!)), at the time macvtap support was added, both vnetX
and macvtapX device names were always included when formatting the
XML.
Then in commit a8be259d0c (July 2011, libvirt-0.9.4), <interface>
formatting was changed to also clear out "vnetX" device names during
XML formatting as well. However the same treatment wasn't given to
"macvtapX".
Now in 2020, there has been a report that a failed migration leads to
the macvtap device of some other unrelated guest on the destination
host losing its network connectivity. It was determined that this was
due to the domain XML in the migration containing a macvtap device
name, e.g. "macvtap0", that was already in use by the other guest on
the destination. Normally this wouldn't be a problem, because libvirt
would see that the device was already in use, and then find a
different unused name. But in this case, other external problems were
causing the migration to fail prior to selecting a macvtap device and
successfully opening it, and during error recovery, qemuProcessStop()
was called, which went through all def->nets objects and (if they were
macvtap) deleted the device specified in net->ifname; since libvirt
hadn't gotten to the point of replacing the incoming "macvtap0" with
the name of a device it actually created for this guest, that meant
that "macvtap0" was deleted, *even though it was currently in use by a
different guest*!
Whew!
So, it turns out that when formatting "migratable" XML, "vnetX"
devices are omitted, just as when formatting "inactive" XML. By making
the code in both interface parsing and formatting consistent for
"vnetX", "macvtapX", and "macvlanX", we can thus make sure that the
autogenerated (and unneeded / completely *not* wanted) macvtap device
name will not be sent with the migration XML. This way when a
migration fails, net->ifname will be NULL, and libvirt won't have any
device to try and (erroneously) delete.
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Commit <2020c6af8a8e4bb04acb629d089142be984484c8> fixed an issue with
QEMU driver by reporting offline CPUs as well. However, doing so it
introduced a regression into libxl and test drivers by completely
ignoring the passed `hostcpus` variable.
Move the virHostCPUGetAvailableCPUsBitmap() out of the helper into QEMU
driver so it will not affect other drivers which gets the number of host
CPUs differently.
This was uncovered by running libvirt-dbus test suite which counts on
the fact that test driver has hard-coded host definition and must not
depend on the host at all.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
and stop erroneously equating NULL with "". The latter means that the
element has empty content, while the former means there was an error
during parsing (either internal with the parser, or the content of the
XML was bad).
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
virDomainBlkioDeviceParseXML() calls xmlNodeGetContent() multiple
times in a loop, but can easily be refactored to call it once for all
element nodes, and then use the result of that one call in each of the
(mutually exclusive) blocks that previously each had their own call to
xmlNodeGetContent.
This is being done in order to reduce the number of changes needed in
an upcoming patch that will eliminate the lack of checking for NULL on
return from xmlNodeGetContent().
As part of the simplification, the while() loop has been changed into
a for() so that we can use "continue" without bypassing the
"node = node->next".
Signed-off-by: Laine Stump <laine@redhat.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
We already allow controlling the initiator IQN for iSCSI based disks.
Add the same for host devices.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
These variables are only used for assignment and have
no other effect.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
The shmem 'name' specifies the shared memory path in '/dev/shm/',
however, we may need to change it to avoid filename conflict
when VM migrate to other host. This patch remove shmem name
consistency check.
Signed-off-by: Wang Xin <wangxinxin.wang@huawei.com>
Reviewed-by: Martin Kletzander <mkletzan@redhat.com>
Role(master or peer) controls how the domain behaves on migration.
For more details about migration with ivshmem, see
https://git.qemu.org/?p=qemu.git;a=blob_plain;f=docs/system/ivshmem.rst;hb=HEAD
It's a optional attribute in libvirt, and qemu will choose default
role for ivshmem device if the user is not specified.
With device property 'role', the value can be 'master' or 'peer'.
- 'master' (means 'master=on' in qemu), the guest will copy
the shared memory on migration to the destination host.
- 'peer' (means 'master=off' in qemu), the migration is disabled.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Signed-off-by: Yang Hang <yanghang44@huawei.com>
Signed-off-by: Wang Xin <wangxinxin.wang@huawei.com>
Reviewed-by: Martin Kletzander <mkletzan@redhat.com>
When trying to parse an XML with overlapping iothread scheduler
settings, the error message was rather confusing:
error: iothreadssched attributes 'vcpus' must not overlap
Pass the correct element name.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Pass the scheduler element name instead of trying to reconstructing
it from the attribute name.
This has the benefit of not mixing '%s' with regular text in
translatable strings as well as preventing the confusion when
the 's' marking the plural in the element name ('vcpus') is taken
as a first letter of the 'sched' suffix.
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Fixes: 7ea55a481d
Fixes: 99c5fe0e7c
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
virDomainThreadSchedParseHelper is used for parsing both iothread
and vcpu scheduling settings. Rename its 'name' attribute to
make it obvious this refers to the attribute name, not the name of
the element (which is currently constructed from the attribute name).
Signed-off-by: Ján Tomko <jtomko@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
This is only used in the ESX driver where, when set to "no", it will
ignore all the checks libvirt does about the origin of the MAC address
(whether or not it's in a VMWare OUI) and forward the original one to
the ESX server telling it not to check it either.
This allows keeping a deterministic MAC address which can be useful for
licensed software which might dislike changes.
Signed-off-by: Bastien Orivel <bastien.orivel@diateam.net>
VMX conversion parts rewritten to apply on top of previously merged
support for type='generated|static'
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
