Make it obvious to 'dumpxml' readers what unit we are using,
since our default of KiB for memory (1024) differs from qemu's
default of MiB; and differs from our use of bytes for storage.
Tests were updated via:
$ find tests/*data tests/*out -name '*.xml' | \
xargs sed -i 's/<\(memory\|currentMemory\|hard_limit\|soft_limit\|min_guarantee\|swap_hard_limit\)>/<\1 unit='"'KiB'>/"
$ find tests/*data tests/*out -name '*.xml' | \
xargs sed -i 's/<\(capacity\|allocation\|available\)>/<\1 unit='"'bytes'>/"
followed by a few fixes for the stragglers.
Note that with this patch, the RNG for <memory> still forbids
validation of anything except unit='KiB', since the code silently
ignores the attribute; a later patch will expand <memory> to allow
scaled input in the code and update the RNG to match.
* docs/schemas/basictypes.rng (unit): Add 'bytes'.
(scaledInteger): New define.
* docs/schemas/storagevol.rng (sizing): Use it.
* docs/schemas/storagepool.rng (sizing): Likewise.
* docs/schemas/domaincommon.rng (memoryKBElement): New define; use
for memory elements.
* src/conf/storage_conf.c (virStoragePoolDefFormat)
(virStorageVolDefFormat): Likewise.
* src/conf/domain_conf.h (_virDomainDef): Document unit used
internally.
* src/conf/storage_conf.h (_virStoragePoolDef, _virStorageVolDef):
Likewise.
* tests/*data/*.xml: Update all tests.
* tests/*out/*.xml: Likewise.
* tests/define-dev-segfault: Likewise.
* tests/openvzutilstest.c (testReadNetworkConf): Likewise.
* tests/qemuargv2xmltest.c (blankProblemElements): Likewise.
* src/conf/domain_conf.h: Add new member "target" to struct
_virDomainDeviceDriveAddress.
* src/conf/domain_conf.c: Parse and format "target"
* Lots of tests (.xml) in tests/domainsnapshotxml2xmlout,
tests/qemuxml2argvdata, tests/qemuxml2xmloutdata, and
tests/vmx2xmldata/ are modified for newly introduced
attribute "target" for address of "drive" type.
When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
