Creating a large domain could potentially be time consuming. Use the
recently added job functions and unlock the virDomainObj while
the create operation is in progress.
Signed-off-by: Katerina Koukiou <k.koukiou@gmail.com>
Follows the pattern used in the libxl driver for managing multiple,
simultaneous jobs within the driver.
Signed-off-by: Katerina Koukiou <k.koukiou@gmail.com>
Usage of this keyword in front of function declaration that is exported via a
header file is unnecessary, since internally, this has been the default for most
compilers for quite some time.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
SRIOV VFs used in macvtap passthrough mode can take advantage of the
SRIOV card's transparent vlan tagging. All the code was there to set
the vlan tag, and it has been used for SRIOV VFs used for hostdev
interfaces for several years, but for some reason, the vlan tag for
macvtap passthrough devices was stubbed out with a -1.
This patch moves a bit of common validation down to a lower level
(virNetDevReplaceNetConfig()) so it is shared by hostdev and macvtap
modes, and updates the macvtap caller to actually send the vlan config
instead of -1.
Commit 36025c552 tried to improve error reporting for <disk type="lun">
but reused the code in LXC which doesn't care about the actual disk
type. The error messages would then contain a bogous hint that the
config for the 'lun' device is invalid which might not be the case.
Re-do the relevant portion of the commit with the original message.
For disks sources described by a libvirt volume we don't need to do a
complicated check since virStorageTranslateDiskSourcePool already
correctly determines the actual disk type.
Replace the checks using a new accessor that does not open-code the
whole logic.
Admin API needs a way of addressing specific clients. Unlike servers, which we
are happy to address by names both because its name reflects its purpose (to
some extent) and we only have two of them (so far), naming clients doesn't make
any sense, since a) each client is an anonymous, i.e. not recognized after a
disconnect followed by a reconnect, b) we can't predict what kind of requests
it's going to send to daemon, and c) the are loads of them comming and going,
so the only viable option is to use an ID which is of a reasonably wide data
type.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Modeled after the qemuDomainDiskPrivatePtr logic, create a privateData
pointer in the _virDomainHostdevDef to allow storage of private data
for a hypervisor in order to at least temporarily store auth/secrets
data for usage during qemuBuildCommandLine.
NB: Since the qemu_parse_command (qemuParseCommandLine) code is not
expecting to restore the auth/secret data, there's no need to add
code to handle this new structure there.
Updated copyrights for modules touched. Some didn't have updates in a
couple years even though changes have been made.
Signed-off-by: John Ferlan <jferlan@redhat.com>
This reverts commit afee47d07c, which
added support to lxc for the "peer" attribute in domain interface <ip>
elements.
It's being removed temporarily for the release of libvirt 1.3.4
because the feature doesn't work, and there are concerns that it may
need to be modified in an externally visible manner which could create
backward compatibility problems.
It isn't implemented and does not work:
error: internal error: guest failed to start: /usr/lib/libvirt/libvirt_lxc: option '--veth' requires an argument
syntax: /usr/lib/libvirt/libvirt_lxc [OPTIONS] ...
We previously threw an explicit error, but this changed in
22cff52a2b , which I suspect was
untested for LXC
So in glibc-2.23 sys/sysmacros.h is no longer included from sys/types.h
and we don't build because of the usage of major/minor/makedev macros.
Autoconf already has AC_HEADER_MAJOR macro that check where exactly
these functions/macros are defined, so let's use that.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
We include the file in plenty of places. This is mostly due to
historical reasons. The only place that needs something from the
header file is storage_backend_fs which opens _PATH_MOUNTED. But
it gets the file included indirectly via mntent.h. At no other
place in our code we need _PATH_.*. Drop the include and
configure check then.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since servers know their name, there is no need to supply such
information twice. Also defeats inconsistencies.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
At first I did not want to do this, but after trying to implement some
newer feaures in the admin API I realized we need that to make our lives
easier. On the other hand they are not saved redundantly and the
virNetServer objects are still kept in a hash table.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Introduce a helper to check supported device and domain config and move
the memory hotplug checks to it.
The advantage of this approach is that by default all new features are
considered unsupported by all hypervisors unless specifically changed
rather than the previous approach where every hypervisor would need to
declare that a given feature is unsupported.
This is an error message I've just seen. Fix it by initializing
@inode.
CC lxc/libvirt_driver_lxc_impl_la-lxc_process.lo
lxc/lxc_process.c: In function 'virLXCProcessMonitorInitNotify':
lxc/lxc_process.c:767:23: error: 'inode' may be used uninitialized in this function [-Werror=maybe-uninitialized]
virDomainAuditInit(vm, initpid, inode);
^
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since the daemon can manage and add (at fresh start) multiple servers,
we also should be able to add them from a JSON state file in case of a
daemon restart, so post exec restart support for multiple servers is also
provided. Patch also updates virnetdaemontest accordingly.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
When adding disk images to ACL we may call those functions on NFS
shares. In that case we might get an EACCES, which isn't really relevant
since NFS would not hold a block device. This patch adds a flag that
allows to stop reporting an error on EACCES to avoid spaming logs.
Currently there's no functional change.
Since commit 47e5b5ae virCgroupAllowDevice allows to pass -1 as either
the minor or major device number and it automatically uses '*' in place
of that. Reuse the new approach through the code and drop the duplicated
functions.
The virStringListLength function does not ever modify the passed
string list. It merely counts the items in it. Make sure that we
reflect this bit in the function header.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
(crobinso: fix up spacing and squash in sheepdog bit suggested
by Andrea)
So, systemd-machined has this philosophy that machine names are like
hostnames and hence should follow the same rules. But we always allowed
international characters in domain names. Thus we need to modify the
machine name we are passing to systemd.
In order to change some machine names that we will be passing to systemd,
we also need to call TerminateMachine at the end of a lifetime of a
domain. Even for domains that were started with older libvirt. That
can be achieved thanks to virSystemdGetMachineNameByPID(). And because
we can change machine names, we can get rid of the inconsistent and
pointless escaping of domain names when creating machine names.
So this patch modifies the naming in the following way. It creates the
name as <drivername>-<id>-<name> where invalid hostname characters are
stripped out of the name and if the resulting name is longer, it
truncates it to 64 characters. That way we can start domains we
couldn't start before. Well, at least on systemd.
To make it work all together, the machineName (which is needed only with
systemd) is saved in domain's private data. That way the generation is
moved to the driver and we don't need to pass various unnecessary
arguments to cgroup functions.
The only thing this complicates a bit is the scope generation when
validating a cgroup where we must check both old and new naming, so a
slight modification was needed there.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1282846
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The virDomainObjFormat and virDomainSaveStatus methods
both call into virDomainDefFormat, so should be providing
a non-NULL virCapsPtr instance.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
virDomainSaveConfig calls virDomainDefFormat which was setting the caps
to NULL, thus keeping the old behaviour (i.e. not looking at
netprefix). This patch adds the virCapsPtr to the function and allows
the configuration to be saved and skipping interface names that were
registered with virCapabilitiesSetNetPrefix().
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
And use the newly added caps->host.netprefix (if it exists) for
interface names that match the autogenerated target names.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
On the host when we start a container, it will be
placed in a cgroup path of
/machine.slice/machine-lxc\x2ddemo.scope
under /sys/fs/cgroup/*
Inside the containers' namespace we need to setup
/sys/fs/cgroup mounts, and currently will bind
mount /machine.slice/machine-lxc\x2ddemo.scope on
the host to appear as / in the container.
While this may sound nice, it confuses applications
dealing with cgroups, because /proc/$PID/cgroup
now does not match the directory in /sys/fs/cgroup
This particularly causes problems for systems and
will make it create repeated path components in
the cgroup for apps run in the container eg
/machine.slice/machine-lxc\x2ddemo.scope/machine.slice/machine-lxc\x2ddemo.scope/user.slice/user-0.slice/session-61.scope
This also causes any systemd service that uses
sd-notify to fail to start, because when systemd
receives the notification it won't be able to
identify the corresponding unit it came from.
In particular this break rabbitmq-server startup
Future kernels will provide proper cgroup namespacing
which will handle this problem, but until that time
we should not try to play games with hiding parent
cgroups.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
'free' on fedora23 wants to use the Slab field for calculated used
memory. The equation is:
used = MemTotal - MemFree - (Cached + Slab) - Buffers
We already set Cached and Buffers to 0, do the same for Slab and its
related values
https://bugzilla.redhat.com/show_bug.cgi?id=1300781
'free' on Fedora 23 will use MemAvailable to calculate its 'available'
field, but we are passing through the host's value. Set it to match
MemFree, which is what 'free' will do for older linux that don't have
MemAvailable
https://bugzilla.redhat.com/show_bug.cgi?id=1300781
We virtualize bits of /proc/meminfo by replacing host values with
values specific to the container.
However for calculating the final size of the returned data, we are
using the size of the original file and not the altered copy, which
could give garbelled output.
Some of the protocol files already include handing of the missing int
types such as xdr_uint64_t, some don't. To fix it everywhere, move out
of the appropriate defines to the utils/virxdrdefs.h file and include
it where needed.
Signed-off-by: Roman Bogorodskiy <bogorodskiy@gmail.com>
Commit id '71ce4759' altered the cgroup processing with respect to the
call to virCgroupAddTask being moved out from lower layers into the calling
layers especially for qemu processing of emulator and vcpu threads. The
movement affected lxc insomuch as it is possible for a code path to
return a NULL cgroup *and* a 0 return status via virCgroupNewPartition
failure when virCgroupNewIgnoreError succeeded when virCgroupNewMachineManual
returns. Coverity pointed out that would cause virCgroupAddTask to core.
This patch will check for a NULL cgroup as well as the negative return
and just return the NULL cgroup to the caller (as it would have previously)
virCgroupNewMachine used to add the pidleader to the newly created
machine cgroup. Do not do this implicit anymore.
Signed-off-by: Henning Schild <henning.schild@siemens.com>
For the multiqueue on macvtaps we are going to need to open
the device multiple times. Currently, this is not supported.
Rework the function, so that upper layers can be reworked too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So yet again one of integer arguments that we use as a boolean.
Since the argument count of the function is unbearably long
enough, lets turn those booleans into flags.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This change ensures to call driver specific post-parse code to modify
domain definition after parsing hypervisor config the same way we do
after parsing XML.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Instead of creating symlinks, bind mount the devices to
/dev/pts/XY.
Using bind mounts it is no longer needed to add pts devices
to files like /etc/securetty.
Signed-off-by: Richard Weinberger <richard@nod.at>
Userspace does not expect that the initial console
is a controlling TTY. systemd can deal with that, others not.
On sysv init distros getty will fail to spawn a controlling on
/dev/console or /dev/tty1. Which will cause to whole container
to reboot upon ctrl-c.
This patch changes the behavior of libvirt to match the kernel
behavior where the initial TTY is also not controlling.
The only user visible change should be that a container with
bash as PID 1 would complain. But this matches exactly the kernel
be behavior with init=/bin/bash.
To get a controlling TTY for bash just run "setsid /bin/bash".
Signed-off-by: Richard Weinberger <richard@nod.at>
