The unprivileged libvirtd does not have permission to create firewall
rules, or bridge devices, or do anything to the host network in
general. Historically we still activate the network driver though and
let the network start API call fail.
The startup code path which reloads firewall rules on active networks
would thus effectively be a no-op when unprivileged as it is impossible
for there to be any active networks
With the change to use a global set of firewall chains, however, we now
have code that is run unconditionally.
Ideally we would not register the network driver at all when
unprivileged, but the entanglement with the virt drivers currently makes
that impractical. As a temporary hack, we just make the firewall reload
into a no-op.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
During startup libvirtd creates top level chains for both ipv4
and ipv6 protocols. If this fails for any reason then startup
of virtual networks is blocked.
The default virtual network, however, only requires use of ipv4
and some servers have ipv6 disabled so it is expected that ipv6
chain creation will fail. There could equally be servers with
no ipv4, only ipv6.
This patch thus makes error reporting a little more fine grained
so that it works more sensibly when either ipv4 or ipv6 is
disabled on the server. Only the protocols that are actually
used by the virtual network have errors reported.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
During startup we create some top level chains in which all
virtual network firewall rules will be placed. The upfront
creation is done to avoid slowing down creation of individual
virtual networks by checking for chain existance every time.
There are some factors which can cause this upfront creation
to fail and while a message will get into the libvirtd log
this won't be seen by users who later try to start a virtual
network. Instead they'll just get a message saying that the
libvirt top level chain does not exist. This message is
accurate, but unhelpful for solving the root cause.
This patch thus saves any error during daemon startup and
reports it when trying to create a virtual network later.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The rbd_list method has been deprecated in Ceph >= 14.0.0
in favour of the new rbd_list2 method which populates an
array of structs.
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The rbd_list method has a quite unpleasant signature returning an
array of strings in a single buffer instead of an array. It is
being deprecated in favour of rbd_list2. To maintain clarity of
code when supporting both APIs in parallel, split the rbd_list
code out into a separate method.
In splitting this we now honour the rbd_list failures.
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
After this, newly added enums will not automatically show up in
driver output unless the driver code specifically sets report=true
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Set report=true for all enums currently formatted in the XML
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Set report=true for all enums currently formatted in the XML
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Set report=true for all enums currently formatted in the XML
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
virCapsEnum report is an internal bool indicating whether we
should format the enum in the XML at all. This is unused for
now but will be handled in future patches.
We use a plain bool instead of tristate because the case here
is a bit different than the explicit @supported output. We
already report the equivalent of supported=YES|NO based on
what enum values are filled in. This adds report=false to
handle the ABSENT case.
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Change domcaps to skip formatting XML if the default
TRISTATE_BOOL_ABSENT is found. Now when domcaps is extended, driver
XML output won't change until an explicit TRISTATE_BOOL value is set
in driver code.
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Upcoming changes will make outputting these subelements optional.
While we are here drop the useless interleave: since this is an output
only format the elements are always in the same order
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
<hostdev> and <features> are not supported. <loader>, <graphics>,
and <video> are supported conditionally
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
None of the <feature> bits are supported, and the <loader> piece
is only conditionally supported
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Only gic->supported needs an explicit BOOL_NO setting, all other
'supported' values are handling things correctly
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Switch most 'supported' handling to use virTristateBool, so eventually
we can handle the ABSENT state.
For now the XML formatter treats ABSENT the same as FALSE, so there's
no functional output change. This will be addressed in later patches
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Similar to the macros we have for formatting enums, add a macro to
simplify formatting the pattern:
<FOO supported='yes|no'/>
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
The 'full' test verifies the output of a virDomainCapsPtr built
by hand. It has the following problems:
The domcaps test suite nowadays has 3 hypervisor driver implementations
which should give us plenty of opportunity to get full domcaps coverage.
I don't think this test has much value. And it has the following issues:
- Requires manual intervention to test new domcaps XML, which is easy
to miss, for example gic bits aren't covered there.
- The SET_ALL_BITS trick it uses to fill in enums will output
values that are never reported by any driver implementation
(strings like 'default')
Let's remove it
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
The 'empty' demonstrates XML generated when only bare minimum caps
data has been filled in. This will demonstrate changes that alter
the default XML output.
Acked-by: Michal Privoznik <mprivozn@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
We already document how to generate them, so might as well
go the extra mile and document the remaining steps.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Acked-by: Michal Privoznik <mprivozn@redhat.com>
In 0eca80e60 _class was renamed to klass for variety of struct
members. However, gather_usb_cap() was missed out in this rename
leaving FreeBSD build broken.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This code originates from:
commit d0aa10fdd6
Author: Daniel P. Berrange <berrange@redhat.com>
Date: Tue Mar 3 12:03:44 2009 +0000
QEMU security driver usage for sVirt support (James Morris, Dan Walsh, Daniel Berrange)
Originally in the qemudDomainGetSecurityLabel function. It doesn't
appear to have done anything useful back then either. The other two
instances look like copy+paste
Reviewed-by: Ján Tomko <jtomko@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
In d16f803d78 we've tried to solve an issue that after wiping an
image its format might have changed (e.g. from qcow2 to raw) but
libvirt wasn't probing the image format. We fixed this by calling
virStorageBackendRefreshVolTargetUpdate() which is what
refreshPool() would end up calling. But this shortcut is not good
enough because the function is called only for local types of
volumes (like dir, fs, netfs). But now that more backends support
volume wiping we have to call the function with more caution.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
So far we have two branches: either we zero BLOCK_PER_PACKET
(currently 128) block at once, or if we're close to the last block
then we zero out one block at the time. This is very suboptimal.
We know how many block are there left. Might as well just write
them all at once.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
This command is fully async. Note that users can use virsh event to be
notified of the guest actually removing the device.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
Mention that successful return does not equal to device being detached
similarly as we do at the API level.
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Erik Skultety <eskultet@redhat.com>
This info can be useful to filter devices visible
to mgmt clients so that they won't see devices that
unsafe/not meaningful to pass thru.
Provide class info the way it is provided by udev or
kernel that is as single 6-digit hexadecimal.
Class element is not optional. I guess this should not
break users that use virNodeDeviceCreateXML because
they probably specify only scsi_host capability on
input and then node device driver gets other capabilities
from udev after device appeared.
HAL driver does not get support for the new element in
this patch.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Vim treats *.h files as cpp ones with respect to syntax highlighting.
Thus "class" in _virNodeDevCapPCIDev highlighted mistakenly.
This can be fixed by filetype detection code tunables but it
is more convinient to skip this tuning by every project member.
Let's just use "klass" as field name instead of _class or class
and add syntax rule.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Commit [1] moved snapshot list functions declaration into
its own file but missed a fix for vz driver.
[1] 9b75154c : snapshot: Break out virDomainSnapshotObjList into its own file
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Only active pools can be refreshed. But our completer offers just
all pool, even inactive ones.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
If pool refresh failed, then the internal table of volumes is
probably left in inconsistent or incomplete state anyways. Clear
it out then. This has an advantage that we can move the
virStoragePoolObjClearVols() from those very few backends that
do call it.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
This is a wrapper over refreshPool() call as at all places we are
doing basically the same. Might as well have a single function to
call.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
In bf5cf610f2 I've fixed a problem where iscsi-direct
backend was reporting only the last LUN. The fix consisted of
moving virStoragePoolObjClearVols() one level up. However, as it
turns out, storage driver already calls it before calling
refreshPool callback (which is
virStorageBackendISCSIDirectRefreshPool() in this case).
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
If virStorageBackendISCSIDirectVolWipeZero() fails, it has
already reported an error which is probably specific enough. Do
not overwrite it with some generic one.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
This function reports error for one of the two error paths. This
is unfortunate as a caller see this function failing but doesn't
know right away if an error was reported.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Pavel Hrdina <phrdina@redhat.com>
Now that we no longer support the weird "redhat+systemd"
configuration, we can make our code slightly simpler.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Despite the misleading name, these were supposed to be used
with a System V style init; however, none of the platforms we
target is using that kind of init anymore: almost all Linux
distributions have switched to systemd, those that haven't
(such as Gentoo and Alpine) are mostly using OpenRC with
custom init scripts, and the BSDs have been doing their own
thing all along.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Not a single one of the platforms we target still uses Upstart, and
the Upstart project itself has been abandoned for several years now.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
We're gonna drop support for non-systemd init scripts soon,
and we don't want Travis CI builds to break when we do.
Since we have init system auto-detection, we can just rely on
that and stop passing --with-init-script to configure entirely.
Signed-off-by: Andrea Bolognani <abologna@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
snapshot_conf.h was mixing three separate types: the snapshot
definition, the snapshot object, and the snapshot object list.
Separate out the snapshot object list code into its own file, and
update includes for affected clients.
This is just code motion, but done in preparation of sharing a lot of
the object list code with checkpoints.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
The next patch will require access to the helper functions
virDomainSnapshotDefFormatInternal and
virDomainSnapshotRedefineValidate from two different files; make the
file split easier by exporting these functions.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
snapshot_conf.h was mixing three separate types: the snapshot
definition, the snapshot object, and the snapshot object list.
Separate out the snapshot object code into its own file, which
includes moving a typedef to avoid circular inclusions.
Mostly straight code motion, although I fixed a comment along
the way, now that virDomainSnapshotForEachDescendent now
guarantees a topological visit (missed in b647d219).
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
It's easier to locate a typedef if they are stored in sorted order;
do so mechanically via:
$ sed -i '/typedef struct/ {N; N; s/\n//g}' src/conf/virconftypes.h
$ # sorting the lines
$ sed -i '/typedef struct/ s/;/;\n/g' src/conf/virconftypes.h
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Ján Tomko <jtomko@redhat.com>
