Commit Graph

7 Commits

Author SHA1 Message Date
Laine Stump
30a6f91686 network: allow configuring firewalld zone for virtual network bridge device
Since we're setting the zone anyway, it will be useful to allow
setting a different (custom) zone for each network. This will be done
by adding a "zone" attribute to the "bridge" element, e.g.:

   ...
   <bridge name='virbr0' zone='myzone'/>
   ...

If a zone is specified in the config and it can't be honored, this
will be an error.

Signed-off-by: Laine Stump <laine@laine.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
2019-02-01 12:57:13 -05:00
Ján Tomko
d8bd24a9ec Remove the space before the slash in network XML
This matches the style we use elsewhere and allows
nat-network-dns-srv-record{,-minimal}.xml to be tested in
network XML -> XML test.
2013-08-28 08:05:46 +02:00
Peter Krempa
ab4bf20ead util: Change virMacAddrFormat to lowercase hex characters
The domain XML generator creates the mac addres strings with lowercase
strings with a separate piece of code. This patch changes the formating
helper to do the same stuff to allow using it to normalize a string
provided by the user. After this change some of the tests that are
outputing the mac address will need to be changed.
2013-04-02 15:53:43 +02:00
Laine Stump
40fd7073be conf: support abstracted interface info in network XML
The network XML is updated in the following ways:

1) The <forward> element can now contain a list of forward interfaces:

     <forward .... >
       <interface dev='eth10'/>
       <interface dev='eth11'/>
       <interface dev='eth12'/>
       <interface dev='eth13'/>
     </forward>

   The first of these takes the place of the dev attribute that is
   normally in <forward> - when defining a network you can specify
   either one, and on output both will be present. If you specify
   both on input, they must match.

2) In addition to forward modes of 'nat' and 'route', these new modes
   are supported:

     private, passthrough, vepa - when this network is referenced by a
     domain's interface, it will have the same effect as if the
     interface had been defined as type='direct', e.g.:

        <interface type='direct'>
          <source mode='${mode}' dev='${dev}>
          ...
        </interface>

     where ${mode} is one of the three new modes, and ${dev} is an interface
     selected from the list given in <forward>.

     bridge - if a <forward> dev (or multiple devs) is defined, and
     forward mode is 'bridge' this is just like the modes 'private',
     'passthrough', and 'vepa' above. If there is no forward dev
     specified but a bridge name is given (e.g. "<bridge
     name='br0'/>"), then guest interfaces using this network will use
     libvirt's "host bridge" mode, equivalent to this:

       <interface type='bridge'>
          <source bridge='${bridge-name}'/>
          ...
       </interface>

3) A network can have multiple <portgroup> elements, which may be
   selected by the guest interface definition (by adding
   "portgroup='${name}'" in the <source> element along with the
   network name). Currently a portgroup can only contain a
   virtportprofile, but the intent is that other configuration items
   may be put there int the future (e.g. bandwidth config). When
   building a guest's interface, if the <interface> XML itself has no
   virtportprofile, and if the requested network has a portgroup with
   a name matching the name given in the <interface> (or if one of the
   network's portgroups is marked with the "default='yes'" attribute),
   the virtportprofile from that portgroup will be used by the
   interface.

4) A network can have a virtportprofile defined at the top level,
   which will be used by a guest interface when connecting in one of
   the 'direct' modes if the guest interface XML itself hasn't
   specified any virtportprofile, and if there are also no matching
   portgroups on the network.
2011-07-21 14:46:53 -04:00
Laine Stump
5754dbd56d Give each virtual network bridge its own fixed MAC address
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=609463

The problem was that, since a bridge always acquires the MAC address
of the connected interface with the numerically lowest MAC, as guests
are started and stopped, it was possible for the MAC address to change
over time, and this change in the network was being detected by
Windows 7 (it sees the MAC of the default route change), so on each
reboot it would bring up a dialog box asking about this "new network".

The solution is to create a dummy tap interface with a MAC guaranteed
to be lower than any guest interface's MAC, and attach that tap to the
bridge as soon as it's created. Since all guest MAC addresses start
with 0xFE, we can just generate a MAC with the standard "0x52, 0x54,
0" prefix, and it's guaranteed to always win (physical interfaces are
never connected to these bridges, so we don't need to worry about
competing numerically with them).

Note that the dummy tap is never set to IFF_UP state - that's not
necessary in order for the bridge to take its MAC, and not setting it
to UP eliminates the clutter of having an (eg) "virbr0-nic" displayed
in the output of the ifconfig command.

I chose to not auto-generate the MAC address in the network XML
parser, as there are likely to be consumers of that API that don't
need or want to have a MAC address associated with the
bridge.

Instead, in bridge_driver.c when the network is being defined, if
there is no MAC, one is generated. To account for virtual network
configs that already exist when upgrading from an older version of
libvirt, I've added a %post script to the specfile that searches for
all network definitions in both the config directory
(/etc/libvirt/qemu/networks) and the state directory
(/var/lib/libvirt/network) that are missing a mac address, generates a
random address, and adds it to the config (and a matching address to
the state file, if there is one).

docs/formatnetwork.html.in: document <mac address.../>
docs/schemas/network.rng: add nac address to schema
libvirt.spec.in: %post script to update existing networks
src/conf/network_conf.[ch]: parse and format <mac address.../>
src/libvirt_private.syms: export a couple private symbols we need
src/network/bridge_driver.c:
    auto-generate mac address when needed,
    create dummy interface if mac address is present.
tests/networkxml2xmlin/isolated-network.xml
tests/networkxml2xmlin/routed-network.xml
tests/networkxml2xmlout/isolated-network.xml
tests/networkxml2xmlout/routed-network.xml: add mac address to some tests
2011-02-17 13:36:32 -05:00
Laine Stump
008abeeeb9 make the <dhcp> element optional in network.rng
In practice this has always been optional, but the RNG has shown it as
mandatory, and since all the examples for make check had it, it was
never noticed. One of the existing test cases has been changed to
check for this.

I also noticed that the dhcp/host/ip was still defined as <text/>,
but should really be <ref name='ipv4-addr'/>
2010-12-23 15:53:44 -05:00
Cole Robinson
6d8331fd58 tests: Add network XML to XML tests. 2009-10-16 10:52:26 -04:00