By default, qemu user's home dir points to '/' which shouldn't be used
at all. We therefore pass the HOME variable from the current variable
iff not running as SUID, which means that for systemd we never set it.
This patch makes sure, that for system QEMU this is always set to
libDir/<driver>, session mode is left untouched.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
For session mode, only XDG_CACHE_HOME is set, because we want to remain
integrating with services in user session, but for system mode, this
would have become reading/writing to '/' which carries the obvious issue
with permissions (also, '/' is the wrong location in 99.9% cases anyway).
Signed-off-by: Erik Skultety <eskultet@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Add <controller type='scsi' model handling for virtio transitional
devices. Ex:
<controller type='scsi' model='virtio-transitional'/>
* "virtio-transitional" maps to qemu "virtio-scsi-pci-transitional"
* "virtio-non-transitional" maps to qemu "virtio-scsi-non-transitional"
The naming here doesn't match the pre-existing model=virtio-scsi.
The prescence of '-scsi' there seems kind of redundant as we have
type='scsi' already, so I decided to follow the pattern of other
patches and use virtio-transitional etc.
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
<input> devices lack the model= attribute which is used by
most other device types. To eventually support
virtio-input-host-pci-{non-}traditional in qemu, let's add
a standard model= attribute. This just adds the domain_conf
wiring
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
<filesystem> devices lack the model= attribute which is used by
most other device types. To eventually support
virtio-9p-pci-{non-}traditional in qemu, let's add a standard
model= attribute. The accepted values are:
- virtio
- virtio-transitional
- virtio-non-transitional
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
qemu vhost-scsi devices map to XML roughly like:
<hostdev mode='subsystem' type='scsi_host'>
<source protocol='vhost' wwpn=X/>
</hostdev>
To support vhost-scsi-pci-{non-}traditional in qemu, we
need to to extend the SCSI Host hostdev XML to handle
model= value. This matches the XML model= format used
for mediated devices. This is just the domain_conf bits
and some XML test cases.
Use of virtio-X naming here does not match the hostdev
protocol=vhost nor does it match the qemu vhost-X device
naming, however it's more consistent with all other
model= names in this area, and also matches the
inconsistency of <vsock> devices which use model=virtio
but map to vhost-vsock on the qemu commandline
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Add new <disk> model values for virtio transitional devices. When
combined with bus='virtio':
* "virtio-transitional" maps to qemu "virtio-blk-pci-transitional"
* "virtio-non-transitional" maps to qemu "virtio-blk-pci-non-transitional"
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
<disk> devices lack the model= attribute which is used by
most other device types. bus= mostly acts as one, but it
serves other purposes too like determing what target=
prefix to use, and for matching against controller type=
values.
Extending bus= to handle additional virtio transitional
devices will complicate apps lives, and it isn't a clean
mapping anyways. So let's bite the bullet and add a new
<disk model=X/> attribute, and wire up common handling
for virtio and virtio-{non-}transitional
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
