When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
This patch was made in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=738095
In short, qemu's default for the rombar setting (which makes the
firmware ROM of a PCI device visible/not on the guest) was previously
0 (not visible), but they recently changed the default to 1
(visible). Unfortunately, there are some PCI devices that fail in the
guest when rombar is 1, so the setting must be exposed in libvirt to
prevent a regression in behavior (it will still require explicitly
setting <rom bar='off'/> in the guest XML).
rombar is forced on/off by adding:
<rom bar='on|off'/>
inside a <hostdev> element that defines a PCI device. It is currently
ignored for all other types of devices.
At the moment there is no clean method to determine whether or not the
rombar option is supported by QEMU - this patch uses the advice of a
QEMU developer to assume support for qemu-0.12+. There is currently a
patch in the works to put this information in the output of "qemu-kvm
-device pci-assign,?", but of course if we switch to keying off that,
we would lose support for setting rombar on all the versions of qemu
between 0.12 and whatever version gets that patch.
QEMU 0.13 introduced cache=unsafe for -drive, this patch exposes
it in the libvirt layer.
* Introduced a new QEMU capability flag ($prefix_CACHE_UNSAFE),
as even if $prefix_CACHE_V2 is set, we can't know if unsafe
is supported.
* Improved the reliability of qemu cache type detection.
It is important to be able to attach USB redirected devices to a
particular controller (one that supports USB2 for instance).
Without this patch, only the default bus was used.
<redirdev bus='usb' type='spicevmc'>
<address type='usb' bus='0' port='4'/>
</redirdev>
I got confused when 'virsh domblkinfo dom disk' required the
path to a disk (which can be ambiguous, since a single file
can back multiple disks), rather than the unambiguous target
device name that I was using in disk snapshots. So, in true
developer fashion, I went for the best of both worlds - all
interfaces that operate on a disk (aka block) now accept
either the target name or the unambiguous path to the backing
file used by the disk.
* src/conf/domain_conf.h (virDomainDiskIndexByName): Add
parameter.
(virDomainDiskPathByName): New prototype.
* src/libvirt_private.syms (domain_conf.h): Export it.
* src/conf/domain_conf.c (virDomainDiskIndexByName): Also allow
searching by path, and decide whether ambiguity is okay.
(virDomainDiskPathByName): New function.
(virDomainDiskRemoveByName, virDomainSnapshotAlignDisks): Update
callers.
* src/qemu/qemu_driver.c (qemudDomainBlockPeek)
(qemuDomainAttachDeviceConfig, qemuDomainUpdateDeviceConfig)
(qemuDomainGetBlockInfo, qemuDiskPathToAlias): Likewise.
* src/qemu/qemu_process.c (qemuProcessFindDomainDiskByPath):
Likewise.
* src/libxl/libxl_driver.c (libxlDomainAttachDeviceDiskLive)
(libxlDomainDetachDeviceDiskLive, libxlDomainAttachDeviceConfig)
(libxlDomainUpdateDeviceConfig): Likewise.
* src/uml/uml_driver.c (umlDomainBlockPeek): Likewise.
* src/xen/xend_internal.c (xenDaemonDomainBlockPeek): Likewise.
* docs/formatsnapshot.html.in: Update documentation.
* tools/virsh.pod (domblkstat, domblkinfo): Likewise.
* docs/schemas/domaincommon.rng (diskTarget): Tighten pattern on
disk targets.
* docs/schemas/domainsnapshot.rng (disksnapshot): Update to match.
* tests/domainsnapshotxml2xmlin/disk_snapshot.xml: Update test.
As discussed here:
https://www.redhat.com/archives/libvir-list/2011-August/msg00361.htmlhttps://www.redhat.com/archives/libvir-list/2011-August/msg00552.html
Adds snapshot attribute and transient sub-element:
<devices>
<disk type=... snapshot='no|internal|external'>
...
<transient/>
</disk>
</devices>
* docs/schemas/domaincommon.rng (snapshot): New define.
(disk): Add snapshot and persistent attributes.
* docs/formatdomain.html.in: Document them.
* src/conf/domain_conf.h (virDomainDiskSnapshot): New enum.
(_virDomainDiskDef): New fields.
* tests/qemuxml2argvdata/qemuxml2argv-disk-transient.xml: New
test of rng, no args counterpart until qemu support is complete.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.args: New
file, snapshot attribute does not affect args.
* tests/qemuxml2argvdata/qemuxml2argv-disk-snapshot.xml: Likewise.
* tests/qemuxml2argvtest.c (mymain): Run new test.
This patch will probably cause merge conflicts to those trying
to do backports. The end goal is simple - domaincommon.rng
should be the state of domain.rng pre-patch, with a few lines
tweaked in the header, while domain.rng post-patch is now just
a shell that includes domaincommon.rng and sets the <start>.
* docs/schemas/domain.rng: Move guts...
* docs/schemas/domaincommon.rng: ...to new file.
* docs/schemas/domainsnapshot.rng: Allow new xml.
* docs/schemas/Makefile.am (schema_DATA): Distribute new file.
* tests/domainsnapshotxml2xmlout/full_domain.xml: New test.
* libvirt.spec.in (%files client): Ship new file. Sort lines.
* mingw32-libvirt.spec.in: Likewise.
