AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
As of QEMU 0.9.1 the -drive argument can be used to configure
all disks, so the QEMU driver can assume it is always available
and drop support for -hda/-cdrom/etc.
Many of the tests need updating because a great many were
running without CAPS_DRIVE set, so using the -hda legacy
syntax.
Fixing the tests uncovered a bug in the argv -> xml
convertor which failed to handle disk with if=floppy.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1027096
If there's the following snippet in the domain XML, the domain will be
lost upon the daemon restart (if the domain is started prior restart):
<seclabel type='dynamic' relabel='yes'/>
The problem is, the 'label', 'imagelabel' and 'baselabel' are parsed
whenever the VIR_DOMAIN_XML_INACTIVE is *not* present or the label is
static. The latter is not our case, obviously. So, when libvirtd starts
up, it finds domain state xml and parse it. During parsing, many XML
flags are enabled but VIR_DOMAIN_XML_INACTIVE. Hence, our parser tries
to extract 'label', 'imagelabel' and 'baselabel' from the XML which
fails for model='none'. Err, this model - even though not specified in
XML - can be taken from qemu wide config file: /etc/libvirtd/qemu.conf.
However, in order to know we are dealing with model='none' the code in
question must be moved forward a bit. Then a new check must be
introduced. This is what the first two chunks are doing.
But this alone is not sufficient. The domain state XML won't contain the
model attribute without slight modification. The model should be
inserted into the XML even if equal to 'none' and the state XML is being
generated - what if the origin (the @security_driver variable in
qemu.conf) changes during libvirtd restarts?
At the end, a test to catch this scenario is introduced.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
