https://bugzilla.redhat.com/show_bug.cgi?id=998813
Implementation is pretty straight-forward. Of course, not all qemus
out there supports the device, so new capability is introduced and
checked prior each use of the device.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Ivshmem is supported by QEMU since 0.13 release.
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Quite a long time ago, (apparently between qemu 0.12 and 0.13) qemu
quietly began supporting the optional specification of a domain in the
host-side address of all pci passthrough commands (by simply
prepending it to the bus:slot.function format, as
"dddd:bb:ss.f"). Since machines with multiple PCI domains are very
rare, this never came up in practice, so libvirt was never updated to
support it.
This patch takes the first step to supporting specification of a non-0
domain in the host-side address of PCI devices being assigned to a
domain, by adding a capability bit to indicate support
"QEMU_CAPS_HOST_PCI_MULTIDOMAIN", and detect it. Since this support
was added in a version prior to the minimum version required for
QMP-style capabilities detection, the capability is always enabled for
any qemu that uses QMP for capabilities detection. For older qemus,
the only clue that a domain can be specified in the host pci address
is the presence of the string "[seg:]" in the help string for
-pcidevice. (Ironically, libvirt will not be modified to support
specification of domain for -pcidevice, since any qemu new enough for
us to care about also supports "-device pci-assign" or "-device
vfio-pci", which are greatly preferred).
Add a new backend for any character device. This backend uses channel
in spice connection. This channel is similar to spicevmc, but
all-purpose in contrast to spicevmc.
Apart from spicevmc, spiceport-backed chardev will not be formatted
into the command-line if there is no spice to use (with test for that
as well). For this I moved the def->graphics counting to the start
of the function so its results can be used in rest of the code even in
the future.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The support for <boot rebootTimeout="12345"/> was added before we were
checking for qemu command line options in QMP, so we haven't properly
adapted virQEMUCaps when using it and thus we report unsupported
option with new enough qemu.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1042690
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Map the new <panic> device in XML to the '-device pvpanic' command
line of qemu. Clients can then couple the <panic> device and the
<on_crash> directive to control behavior when the guest reports
a panic to qemu.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
This resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=888635
(which was already closed as CANTFIX because the qemu "-boot strict"
commandline option wasn't available at the time).
Problem: you couldn't have a domain that used PXE to boot, but also
had an un-bootable disk device *even if that disk wasn't listed in the
boot order*, because if PXE timed out (e.g. due to the bridge
forwarding delay), the BIOS would move on to the next target, which
would be the unbootable disk device (again - even though it wasn't
given a boot order), and get stuck at a "BOOT DISK FAILURE, PRESS ANY
KEY" message until a user intervened.
The solution available since sometime around QEMU 1.5, is to add
"-boot strict=on" to *every* qemu command. When this is done, if any
devices have a boot order specified, then QEMU will *only* attempt to
boot from those devices that have an explicit boot order, ignoring the
rest.
This test is there to ensure that our capabilities detection code isn't
broken somehow.
How to gather test data:
Firstly, the data is split into two separate files. The former (with
suffix .replies) contains all the qemu replies. This is very fragile as
introducing a new device can mean yet another monitor command and hence
edit of this file in the future. But there's no better way of doing
this. To get this data simply turn on debug logs and copy all the
QEMU_MONITOR_IO_PROCESS lines. But be careful to not copy incomplete
ones (yeah, we report some incomplete lines too). Long story short, at
the libvirtd startup, a dummy qemu is spawn to get all the capabilities.
The latter (with suffix .caps) contains capabilities XML. Just start a
domain and copy the corresponding part from its state XML file.
Including <qemuCaps> tag.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
