Starting a qemu VM with a memory module that has the base address
specified results in the following error:
error: internal error: early end of file from monitor: possible problem:
2015-03-26T03:45:52.338891Z qemu-kvm: -device pc-dimm,node=0,memdev=memdimm0,
id=dimm0,slot=0,base=4294967296: Property '.base' not found
The correct property name for the base address is 'addr'.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
QEMU 2.3 adds these new models to cover Haswell and Broadwell CPUs with
updated microcode. Luckily, they also reverted former the machine type
specific changes to existing models. And since these changes were never
released, we don't need to hack around them in libvirt.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add support to start qemu instance with 'pc-dimm' device. Thanks to the
refactors we are able to reuse the existing function to determine the
parameters.
This patch adds code that parses and formats configuration for memory
devices.
A simple configuration would be:
<memory model='dimm'>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
</memory>
A complete configuration of a memory device:
<memory model='dimm'>
<source>
<pagesize unit='KiB'>4096</pagesize>
<nodemask>1-3</nodemask>
</source>
<target>
<size unit='KiB'>524287</size>
<node>1</node>
</target>
</memory>
This patch preemptively forbids use of the <memory> device in individual
drivers so the users are warned right away that the device is not
supported.
To enable memory hotplug the maximum memory size and slot count need to
be specified. As qemu supports now other units than mebibytes when
specifying memory, use the new interface in this case.
Midonet is an opensource virtual networking that over lays the IP
network between hypervisors. Currently, such networks can be made
with the openvswitch virtualport type.
This patch, defines the schema and documentation that will serve
as basis for the follow up patches that will add support to libvirt
for using Midonet virtual ports for its interfaces. The schema
definition requires that the port profile expresses its interfaceid
as part of the port profile. For that reason, this is part of the
patch too.
Signed-off-by: Antoni Segura Puimedon <toni+libvirt@midokura.com>
Now that the size of guest's memory can be inferred from the NUMA
configuration (if present) make it optional to specify <memory>
explicitly.
To make sure that memory is specified add a check that some form of
memory size was specified. One side effect of this change is that it is
no longer possible to specify 0KiB as memory size for the VM, but I
don't think it would be any useful to do so. (I can imagine embedded
systems without memory, just registers, but that's far from what libvirt
is usually doing).
Forbidding 0 memory for guests also fixes a few corner cases where 0 was
not interpreted correctly and caused failures. (Arguments for numad when
using automatic placement, size of the balloon). This fixes problems
described in https://bugzilla.redhat.com/show_bug.cgi?id=1161461
Test case changes are added to verify that the schema change and code
behave correctly.
Use the NUMA total instead of the configured size both in XML and for
uses in the code once NUMA is enabled for a domain.
One test case change is necessary as the rounding of the individual cell
sizes was not matching the rounding of the total size.
Commit 5aee81a0 introduced a new test for disk-serial. The test fails
on i686 arch because there is no need to add "-cpu qemu32" to command
line. To fix the test update emulator in XML to "/usr/bin/qemu" so we
don't add the "-cpu qemu32" to command while running the test on i686 or
x86_64 host.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
We don't usually do tests purely for one change, but one change was
special because when users will migrate to OVMF/AAVMF, commit 18f9f69b
makes their lives easier by allowing them to interleave <type/> inside
<os/>. It would be nice of us to keep the possibility of them pasting
the loader and nvram elements wherever it is valid, hence this test.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Commit 3e4b783e fixed an issue with RNG schema where this address type
was missing, this commit adds a test for it.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
We have something like pvpanic device. However, in some cases it does
not have any address assigned, in which case we produce this ugly XML
(still valid though):
<devices>
<emulator>/usr/bin/qemu</emulator>
...
<panic>
</panic>
</devices>
Lets format "<panic/>" instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There was a mess in the way how we store unlimited value for memory
limits and how we handled values provided by user. Internally there
were two possible ways how to store unlimited value: as 0 value or as
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED. Because we chose to store memory
limits as unsigned long long, we cannot use -1 to represent unlimited.
It's much easier for us to say that everything greater than
VIR_DOMAIN_MEMORY_PARAM_UNLIMITED means unlimited and leave 0 as valid
value despite that it makes no sense to set limit to 0.
Remove unnecessary function virCompareLimitUlong. The update of test
is to prevent the 0 to be miss-used as unlimited in future.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1146539
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Since the APIs support just one element per namespace and while
modifying an element all duplicates would be removed, let's do this
right away in the post parse callback.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1190590
In commit edd1295e1d I've introduced an
XML element that allows to configure state of the network interface
link. Somehow the RNG schema hunk ended up in a weird place in the
network schema definition. Move it to the right place and add a test
case.
Note that the link state is set up via the monitor at VM startup so I
originally didn't think of adding a test case.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1173468
https://bugzilla.redhat.com/show_bug.cgi?id=1142631
This patch resolves a situation where the same "<target dev='$name'...>"
can be used for multiple disks in the domain.
While the $name is "mostly" advisory regarding the expected order that
the disk is added to the domain and not guaranteed to map to the device
name in the guest OS, it still should be unique enough such that other
domblk* type operations can be performed.
Without the patch, the domblklist will list the same Target twice:
$ virsh domblklist $dom
Target Source
------------------------------------------------
sda /var/lib/libvirt/images/file.qcow2
sda /var/lib/libvirt/images/file.img
Additionally, getting domblkstat, domblkerror, domblkinfo, and other block*
type calls will not be able to reference the second target.
Fortunately, hotplug disallows adding a "third" sda value:
$ qemu-img create -f raw /var/lib/libvirt/images/file2.img 10M
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sda
error: Failed to attach disk
error: operation failed: target sda already exists
$
BUT, it since 'sdb' doesn't exist one would get the following on the same
hotplug attempt, but changing to use 'sdb' instead of 'sda'
$ virsh attach-disk $dom /var/lib/libvirt/images/file2.img sdb
error: Failed to attach disk
error: internal error: unable to execute QEMU command 'device_add': Duplicate ID 'scsi0-0-1' for device
$
Since we cannot fix this issue at parsing time, the best that can be done so
as to not "lose" a domain is to make the check prior to starting the guest
with the results as follows:
$ virsh start $dom
error: Failed to start domain $dom
error: XML error: target 'sda' duplicated for disk sources '/var/lib/libvirt/images/file.qcow2' and '/var/lib/libvirt/images/file.img'
$
Running 'make check' found a few more instances in the tests where this
duplicated target dev value was being used. These also exhibited some
duplicated 'id=' values (negating the uniqueness argument of aliases) in
the corresponding .args file and of course the *xmlout version of a few
input XML files.
Well, not that we are not formatting invalid XML, rather than not as
beautiful as we can:
<cpu mode='host-passthrough'>
</cpu>
If there are no children, let's use the singleton element.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Since s390 does not support usb the default creation of a usb controller
for a domain should not occur.
Also adjust s390 test cases by removing usb device instances since
usb devices are no longer created by default for s390 the s390
test cases need to be adjusted.
Signed-off-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
The mask was stored both as a bitmap and as a string. The string is used
for XML output only. Remove the string, as it can be reconstructed from
the bitmap.
The test change is necessary as the bitmap formatter doesn't "optimize"
using the '^' operator.
So, when building the '-numa' command line, the
qemuBuildMemoryBackendStr() function does quite a lot of checks to
chose the best backend, or to check if one is in fact needed. However,
it returned that backend is needed even for this little fella:
<numatune>
<memory mode="strict" nodeset="0,2"/>
</numatune>
This can be guaranteed via CGroups entirely, there's no need to use
memory-backend-ram to let qemu know where to get memory from. Well, as
long as there's no <memnode/> element, which explicitly requires the
backend. Long story short, we wouldn't have to care, as qemu works
either way. However, the problem is migration (as always). Previously,
libvirt would have started qemu with:
-numa node,memory=X
in this case and restricted memory placement in CGroups. Today, libvirt
creates more complicated command line:
-object memory-backend-ram,id=ram-node0,size=X
-numa node,memdev=ram-node0
Again, one wouldn't find anything wrong with these two approaches.
Both work just fine. Unless you try to migrated from the older libvirt
into the newer one. These two approaches are, unfortunately, not
compatible. My suggestion is, in order to allow users to migrate, lets
use the older approach for as long as the newer one is not needed.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
In order for QEMU vCPU (and other) threads to run with RT scheduler,
libvirt needs to take care of that so QEMU doesn't have to run privileged.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178986
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In our RNG schema we do allow multiple (different) seclabels per-domain,
but don't allow this for devices, yet we neither have a check in our XML parser,
nor in a post-parse callback. In that case we should allow multiple
(different) seclabels for devices as well.
Move the alias name right after the object type for rng-egd backend so
that we can later use the JSON to commandline generator to create the
command line.
Libvirt didn't prefix the random number generator backend object alias
with any string thus the device alias and object alias were identical.
To avoid possible problems, rename the alias for the backend object and
tweak tests to comply with the change.
Signed-off-by: Luyao Huang <lhuang@redhat.com>
Signed-off-by: Peter Krempa <pkrempa@redhat.com>
It is only supported for virtio adapters.
Silently drop it if it was specified for other models,
as is done for other virtio attributes.
Also mention this in the documentation.
https://bugzilla.redhat.com/show_bug.cgi?id=1147195
Change done by commit f309db1f4d wrongly
assumes that qemu can start with a combination of NUMA nodes specified
with the "memdev" option and the appropriate backends, and the legacy
way by specifying only "mem" as a size argument. QEMU rejects such
commandline though:
$ /usr/bin/qemu-system-x86_64 -S -M pc -m 1024 -smp 2 \
-numa node,nodeid=0,cpus=0,mem=256 \
-object memory-backend-ram,id=ram-node1,size=12345 \
-numa node,nodeid=1,cpus=1,memdev=ram-node1
qemu-system-x86_64: -numa node,nodeid=1,cpus=1,memdev=ram-node1: qemu: memdev option must be specified for either all or no nodes
To fix this issue we need to check if any of the nodes requires the new
definition with the backend and if so, then all other nodes have to use
it too.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1182467
QEMU's command line visitor as well as the JSON interface take bytes by
default for memory object sizes. Convert mebibytes to bytes so that we
can later refactor the existing code for hotplug purposes.
QEMU's qapi visitor code allows yes/on/y for true and no/off/n for false
value of boolean properities. Unify the used style so that we can
generate it later and fix test cases.
https://bugzilla.redhat.com/show_bug.cgi?id=1170492
In one of our previous commits (dc8b7ce7) we've done a functional
change even though it was intended as pure refactor. The problem is,
that the following XML:
<vcpu placement='static' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
gets translated into this one:
<vcpu placement='auto' current='2'>6</vcpu>
<cputune>
<emulatorpin cpuset='1-3'/>
</cputune>
<numatune>
<memory mode='strict' placement='auto'/>
</numatune>
We should not change the vcpu placement mode. Moreover, we're doing
something similar in case of emulatorpin and iothreadpin. If they were
set, but vcpu placement was auto, we've mistakenly removed them from
the domain XML even though we are able to set them independently on
vcpus.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
There are some interface types (notably 'server' and 'client')
which instead of allowing the default set of elements and
attributes (like the rest do), try to enumerate only the elements
they know of. This way it's, however, easy to miss something. For
instance, the <address/> element was not mentioned at all. This
resulted in a strange behavior: when such interface was added
into XML, the address was automatically generated by parsing
code. Later, the formatted XML hasn't passed the RNG schema. This
became more visible once we've turned on the XML validation on
domain XML changes: appending an empty line at the end of
formatted XML (to trick virsh think the XML had changed) made
libvirt to refuse the very same XML it formatted.
Instead of trying to find each element and attribute we are
missing in the schema, lets just allow all the elements and
attributes like we're doing that for the rest of types. It's no
harm if the schema is wider than our parser allows.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1130390
The listen address is not mandatory for <interface type='server'>
but when it's not specified, we've been formatting it as:
-netdev socket,listen=(null):5558,id=hostnet0
which failed with:
Device 'socket' could not be initialized
Omit the address completely and only format the port in the listen
attribute.
Also fix the schema to allow specifying a model.
QEMU supports feature specification with -cpu host and we just skip
using that. Since QEMU developers themselves would like to use this
feature, this patch modifies the code to work.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178850
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Well, apparently it's possible for a patch to sneak in through
review process and break 'make check'. It happened just lately
with 0e502466ac which changed the default of vgamem_mb for
qxl device. However, there were left some domain XMLs within our
test suite relying on the old default. These should be updated to
match the change.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Libvirt BZ: https://bugzilla.redhat.com/show_bug.cgi?id=1175397
QEMU BZ: https://bugzilla.redhat.com/show_bug.cgi?id=1170093
In qemu there are two interesting arguments:
1) -numa to create a guest NUMA node
2) -object memory-backend-{ram,file} to tell qemu which memory
region on which host's NUMA node it should allocate the guest
memory from.
Combining these two together we can instruct qemu to create a
guest NUMA node that is tied to a host NUMA node. And it works
just fine. However, depending on machine type used, there might
be some issued during migration when OVMF is enabled (see QEMU
BZ). While this truly is a QEMU bug, we can help avoiding it. The
problem lies within the memory backend objects somewhere. Having
said that, fix on our side consists on putting those objects on
the command line if and only if needed. For instance, while
previously we would construct this (in all ways correct) command
line:
-object memory-backend-ram,size=256M,id=ram-node0 \
-numa node,nodeid=0,cpus=0,memdev=ram-node0
now we create just:
-numa node,nodeid=0,cpus=0,mem=256
because the backend object is obviously not tied to any specific
host NUMA node.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1173507
It occurred to me that OpenStack uses the following XML when not using
regular huge pages:
<memoryBacking>
<hugepages>
<page size='4' unit='KiB'/>
</hugepages>
</memoryBacking>
However, since we are expecting to see huge pages only, we fail to
startup the domain with following error:
libvirtError: internal error: Unable to find any usable hugetlbfs
mount for 4 KiB
While regular system pages are not huge pages technically, our code is
prepared for that and if it helps OpenStack (or other management
applications) we should cope with that.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Add attribute to set vgamem_mb parameter of QXL device for QEMU. This
value sets the size of VGA framebuffer for QXL device. Default value in
QEMU is 8MB so reuse it also in libvirt to not break things.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
So far we didn't have any option to set video memory size for qemu video
devices. There was only the vram (ram for QXL) attribute but it was valid
only for the QXL video device.
To provide this feature to users QEMU has a dedicated device attribute
called 'vgamem_mb' to set the video memory size. We will use the 'vram'
attribute for setting video memory size for other QEMU video devices.
For the cirrus device we will ignore the vram value because it has
hardcoded video size in QEMU.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
QEMU has two different type of QXL display device. The first "qxl-vga"
is for primary video device and second "qxl" is for secondary video
device.
There are also two different ways how to specify those devices on qemu
command line, the first one and obsolete is using "-vga" option and the
current new one is using "-device" option. The "-vga" could be used only
to setup primary video device, so the "-vga qxl" equal to
"-device qxl-vga". Unfortunately the "-vga qxl" doesn't support setting
additional parameters for the device and "-global" option must be used
for this purpose. It's mandatory to use "-global qxl-vga...." to set the
parameters of primary video device previously defined with "-vga qxl".
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
The vram attribute was introduced to set the video memory but it is
usable only for few hypervisors excluding QEMU/KVM and the old XEN
driver. Only in case of QEMU the vram was used for QXL.
This patch updates the documentation to reflect current code in libvirt
and also changes the cases when we will set the default vram attribute.
It also fixes existing strange default value for VGA devices 9MB to 16MB
because the video ram should be rounded to power of two.
The change of default value could affect migrations but I found out that
QEMU always round the video ram to power of two internally so it's safe
to change the default value to the next closest power of two and also
silently correct every domain XML definition. And it's also safe because
we don't pass the value to QEMU.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1076098
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
To be able to express some use cases of the RBD backing with libvirt, we
need to be able to specify a config file for the RBD client to qemu as
that is one of the commonly used options.
Some storage systems have internal support for snapshots. Libvirt should
be able to select a correct snapshot when starting a VM.
This patch adds a XML element to select a storage source snapshot for
the RBD protocol which supports this feature.
To track state of virtio channels this patch adds a new output-only
attribute called 'state' to the <target> element of virtio channels.
This will be later populated with the guest state of the channel.
The recent commit to add support for block_set_io_throttle parameters
from version 1.7 of qemu did not add any tests - this adds the tests
Signed-off-by: John Ferlan <jferlan@redhat.com>
CPU numa topology implicitly allows memory specification in 'KiB'.
Enabling this to accept the 'unit' in which memory needs to be specified.
This now allows users to specify memory in units of choice, and
lists the same in 'KiB' -- just like other 'memory' elements in XML.
<numa>
<cell cpus='0-3' memory='1024' unit='MiB' />
<cell cpus='4-7' memory='1024' unit='MiB' />
</numa>
Also augment test cases to correctly model NUMA memory specification.
This adds the tag 'unit="KiB"' for memory attribute in NUMA cells.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This introduces a testcase for PowerPC compat mode cpu specification.
Signed-off-by: Prerna Saxena <prerna@linux.vnet.ibm.com>
Reviewed-by: Michal Privoznik <mprivozn@redhat.com>
Extending the iothread disk support from pci to pci and ccw.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
There was no check for 'nodeset' attribute in numatune-related
elements. This patch adds validation that any nodeset specified does
not exceed maximum host node.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
The mode attribute is required for the source element of vhost-user.
Thus virDomainNetDefFormat should always generate a xml with it and not
only when the mode is server.
The commit fixes the issue. And it adds a vhostuser interface in
'client' mode to qemuxml2argv-net-vhostuser.(args|xml) to test this
usecase.
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
This new attribute will control whether or not libvirt will pay
attention to guest notifications about changes to network device mac
addresses and receive filters. The default for this is 'no' (for
security reasons). If it is set to 'yes' *and* the specified device
model and connection support it (currently only macvtap+virtio) then
libvirt will watch for NIC_RX_FILTER_CHANGED events, and when it
receives one, it will issue a query-rx-filter command, retrieve the
result, and modify the host-side macvtap interface's mac address and
unicast/multicast filters accordingly.
The functionality behind this attribute will be in a later patch. This
patch merely adds the attribute to the top-level of a domain's
<interface> as well as to <network> and <portgroup>, and adds
documentation and schema/xml2xml tests. Rather than adding even more
test files, I've just added the net attribute in various applicable
places of existing test files.
This patch implements support for the ivshmem device in QEMU.
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
This patch adds parsing/formatting code as well as documentation for
shared memory devices. This will currently be only accessible in QEMU
using it's ivshmem device, but is designed as generic as possible to
allow future expansion for other hypervisors.
In the devices section in the domain XML users may specify:
- For shmem device using a server:
<shmem name='shmem0'>
<server path='/tmp/socket-ivshmem0'/>
<size unit='M'>32</size>
<msi vectors='32' ioeventfd='on'/>
</shmem>
- For ivshmem device not using an ivshmem server:
<shmem name='shmem1'>
<size unit='M'>32</size>
</shmem>
Most of the configuration is made optional so it also allows
specifications like:
<shmem name='shmem1/>
<shmem name='shmem2'>
<server/>
</shmem>
Signed-off-by: Maxime Leroy <maxime.leroy@6wind.com>
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Right now when building the qemu command line, we try to do various
unconditional validations of the guest CPU against the host CPU. However
this checks are overly applied. The only time we should use the checks
are:
- The user requests host-model/host-passthrough, or
- When KVM is requsted. CPU features requested in TCG mode are always
emulated by qemu and are independent of the host CPU, so no host CPU
checks should be performed.
Right now if trying to specify a CPU for arm on an x86 host, it attempts
to do non-sensical validation and falls over.
Switch all the test cases that were intending to test CPU validation to
use KVM, so they continue to test the intended code.
Amend some aarch64 XML tests with a CPU model, to ensure things work
correctly.
Add options for tuning segment offloading:
<driver>
<host csum='off' gso='off' tso4='off' tso6='off'
ecn='off' ufo='off'/>
<guest csum='off' tso4='off' tso6='off' ecn='off' ufo='off'/>
</driver>
which control the respective host_ and guest_ properties
of the virtio-net device.
We are not detecting the presence of FIPS from QEMU, but from procfs and
that means it's not QEMU capability. It was decided that we will pass
this flag to QEMU even if it's not supported by old QEMU binaries.
This patch also reverts changes done by commit a21cfb0f to
qemucapabilitestest and implements a new test case in qemuxml2argvtest.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1135431
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1135396
There are two ways how to tell qemu to use huge pages. The first one
is suitable for domains with NUMA nodes: the path to hugetlbfs mount
is appended to NUMA node definition on the command line. The second
one is suitable for UMA domains: here there's this global '-mem-path'
argument that accepts path to the hugetlbfs mount point. However, the
latter case was not used for all the cases that it should be. For
instance:
<memoryBacking>
<hugepages>
<page size='2048' unit='KiB' nodeset='0'/>
</hugepages>
</memoryBacking>
didn't trigger the '-mem-path' so the huge pages - despite being
configured - were not used at all.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of 136ad4974 it is possible to specify different huge pages per
guest NUMA node. However, there's no check if nodeset specified in
./hugepages/page contains only those guest NUMA nodes that exist.
In other words with current code it is possible to define meaningless
combination:
<memoryBacking>
<hugepages>
<page size='1048576' unit='KiB' nodeset='0,2-3'/>
<page size='2048' unit='KiB' nodeset='1,4'/>
</hugepages>
</memoryBacking>
<vcpu placement='static'>4</vcpu>
<cpu>
<numa>
<cell id='0' cpus='0' memory='1048576'/>
<cell id='1' cpus='1' memory='1048576'/>
<cell id='2' cpus='2' memory='1048576'/>
<cell id='3' cpus='3' memory='1048576'/>
</numa>
</cpu>
Notice the node 4 in <hugepages/>?
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
For tuning the network, alternative devices
for creating tap and vhost devices can be specified via:
<backend tap='/dev/net/tun' vhost='/dev/net-vhost'/>
We already are checking for negative value, reporting an error, but
using wrong function and the check only succeeds when a value that
cannot be converted to number successfully is encountered. This patch
provides just a minor change in call of the right version
of function virStrToLong.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1138539
I noticed this with the recent iothread pinning code, but the
problem existed longer than that. The XML validation required
users to supply <cputune> children in a strict order, even though
there was no conceptual reason why they can't occur in any order.
docs/ changes best viewed with -w
* docs/schemas/domaincommon.rng (cputune): Add interleave.
* tests/qemuxml2argvdata/qemuxml2argv-cputune-iothreads.xml: Swap
up order, copying canonical form...
* tests/qemuxml2xmloutdata/qemuxml2xmlout-cputune-iothreads.xml:
...here.
* tests/qemuxml2xmltest.c (mymain): Mark the difference.
Signed-off-by: Eric Blake <eblake@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1101574
Add an option 'iothreadpin' to the <cpuset> to allow for setting the
CPU affinity for each IOThread.
The iothreadspin will mimic the vcpupin with respect to being able to
assign each iothread to a specific CPU, although iothreads ids start
at 1 while vcpu ids start at 0. This matches the iothread naming scheme.
QEMU now supports UEFI with the following command line:
-drive file=/usr/share/OVMF/OVMF_CODE.fd,if=pflash,format=raw,unit=0,readonly=on \
-drive file=/usr/share/OVMF/OVMF_VARS.fd,if=pflash,format=raw,unit=1 \
where the first line reflects <loader> and the second one <nvram>.
Moreover, these two lines obsolete the -bios argument.
Note that UEFI is unusable without ACPI. This is handled properly now.
Among with this extension, the variable file is expected to be
writable and hence we need security drivers to label it.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Up to now, users can configure BIOS via the <loader/> element. With
the upcoming implementation of UEFI this is not enough as BIOS and
UEFI are conceptually different. For instance, while BIOS is ROM, UEFI
is programmable flash (although all writes to code section are
denied). Therefore we need new attribute @type which will
differentiate the two. Then, new attribute @readonly is introduced to
reflect the fact that some images are RO.
Moreover, the OVMF (which is going to be used mostly), works in two
modes:
1) Code and UEFI variable store is mixed in one file.
2) Code and UEFI variable store is separated in two files
The latter has advantage of updating the UEFI code without losing the
configuration. However, in order to represent the latter case we need
yet another XML element: <nvram/>. Currently, it has no additional
attributes, it's just a bare element containing path to the variable
store file.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
To date, anyone performing a block copy and pivot ends up with
the destination being treated as <disk type='file'>. While this
works for data access for a block device, it has at least one
noticeable shortcoming: virDomainGetBlockInfo() reports allocation
differently for block devices visited as files (the size of the
device) than for block devices visited as <disk type='block'>
(the maximum sector used, as reported by qemu); and this difference
is significant when trying to manage qcow2 format on block devices
that can be grown as needed.
Of course, the more powerful virDomainBlockCopy() API can already
express the ability to set the <disk> type. But a new API can't
be backported, while a new flag to an existing API can; and it is
also rather inconvenient to have to resort to the full power of
generating XML when just adding a flag to the older call will do
the trick. So this patch enhances blockcopy to let the user flag
when the resulting XML after the copy must list the device as
type='block'.
* include/libvirt/libvirt.h.in (VIR_DOMAIN_BLOCK_REBASE_COPY_DEV):
New flag.
* src/libvirt.c (virDomainBlockRebase): Document it.
* tools/virsh-domain.c (opts_block_copy, blockJobImpl): Add
--blockdev option.
* tools/virsh.pod (blockcopy): Document it.
* src/qemu/qemu_driver.c (qemuDomainBlockRebase): Allow new flag.
(qemuDomainBlockCopy): Remember the flag, and make sure it is only
used on actual block devices.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
This commit is rather big. Firstly, the in memory config
representation is adjusted like if security_driver was set to "none".
The rest is then just adaptation to the new code that will generate
different seclabels.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
For virtio-blk-pci disks with the disk iothread attribute that are
running the correct emulator, add the "iothread=iothread#" to the
-device command line in order to enable iothreads for the disk as
long as the command is available, the disk iothread value provided is
valid, and is supported for the disk device being added
Add a new capability to ensure the iothreads feature exists for the qemu
emulator being run - requires the "query-iothreads" QMP command. Using the
domain XML add correspoding command argument in order to generate the
threads. The iothreads will use a name space "iothread#" where, the
future patch to add support for using an iothread to a disk definition to
merely define which of the available threads to use.
Add tests to ensure the xml/argv processing is correct. Note that no
change was made to qemuargv2xmltest.c as processing the -object element
would require knowing more than just iothreads.
QEMU 2.1 added support for the kvm=off option to the -cpu command,
allowing the KVM hypervisor signature to be hidden from the guest.
This enables disabling of some paravirualization features in the
guest as well as allowing certain drivers which test for the
hypervisor to load. Domain XML syntax is as follows:
<domain type='kvm>
...
<features>
...
<kvm>
<hidden state='on'/>
</kvm>
</features>
...
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When trying to set numatune mode directly using virsh numatune command,
correct error is raised, however numatune structure was not deallocated,
thus resulting in creating an empty numatune element in the guest XML,
if none was present before. Running the same command aftewards results
in a successful change with broken XML structure. Patch fixes the
deallocation problem as well as checking for invalid attribute
combination VIR_DOMAIN_NUMATUNE_PLACEMENT_AUTO + a nonempty nodeset.
Resolves https://bugzilla.redhat.com/show_bug.cgi?id=1129998
https://bugzilla.redhat.com/show_bug.cgi?id=1128751
There's this <driver/> element under <interface/> which can have
several attributes. However, the driver element is currently formated
only if the driver's name or txmode has been specified. This makes
only a little sense as we parse even partial <driver/>, for instance:
<interface type='user'>
<mac address='52:54:00:e5:48:58'/>
<model type='virtio'/>
<driver ioeventfd='on' event_idx='on' queues='5'/>
</interface>
But such XML would never get formatted back.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Introduce a new structure to handle an iSCSI host device based on the
existing virDomainHostdevSubsysSCSI by adding a "protocol='iscsi'" to
the <source/> element. The existing scsi_host subsystem RNG was modified
to read an optional "protocol='adapter'", although it won't be written
out nor is it documented as an option (by choice).
The new hostdev structure mimics the existing <disk/> element for an
iSCSI device (network) device. New XML is:
<hostdev mode='subsystem' type='scsi' managed='yes'>
<source protocol='iscsi' name='iqn.1992-01.com.example'>
<host name='example.org' port='3260'/>
<auth username='myname'>
<secret type='iscsi' usage='mycluster_myname'/>
</auth>
</source>
<address type='drive' controller='0' bus='0' target='2' unit='5'/>
</hostdev>
The controller element will mimic the existing scsi_host code insomuch
as when 'lsi' and 'virtio-scsi' are used.
A future patch is going to wire up qemu active block commit jobs;
but as they have similar events and are canceled/pivoted in the
same way as block copy jobs, it is easiest to track all bookkeeping
for the commit job by reusing the <mirror> element. This patch
adds domain XML to track which job was responsible for creating a
mirroring situation, and adds a job='copy' attribute to all
existing uses of <mirror>. Along the way, it also massages the
qemu monitor backend to read the new field in order to generate
the correct type of libvirt job (even though it requires a
future patch to actually cause a qemu event that can be reported
as an active commit). It also prepares to update persistent XML
to match changes made to live XML when a copy completes.
* docs/schemas/domaincommon.rng: Enhance schema.
* docs/formatdomain.html.in: Document it.
* src/conf/domain_conf.h (_virDomainDiskDef): Add a field.
* src/conf/domain_conf.c (virDomainBlockJobType): String conversion.
(virDomainDiskDefParseXML): Parse job type.
(virDomainDiskDefFormat): Output job type.
* src/qemu/qemu_process.c (qemuProcessHandleBlockJob): Distinguish
active from regular commit.
* src/qemu/qemu_driver.c (qemuDomainBlockCopy): Set job type.
(qemuDomainBlockPivot, qemuDomainBlockJobImpl): Clean up job type
on completion.
* tests/qemuxml2xmloutdata/qemuxml2xmlout-disk-mirror-old.xml:
Update tests.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Likewise.
* tests/qemuxml2argvdata/qemuxml2argv-disk-active-commit.xml: New
file.
* tests/qemuxml2xmltest.c (mymain): Drive new test.
Signed-off-by: Eric Blake <eblake@redhat.com>
Doing a blockcopy operation across a libvirtd restart is not very
robust at the moment. In particular, we are clearing the <mirror>
element prior to telling qemu to finish the job. Also, thanks to the
ability to request async completion, the user can easily regain
control prior to qemu actually finishing the effort, and they should
be able to poll the domain XML to see if the job is still going.
A future patch will fix things to actually wait until qemu is done
before modifying the XML to reflect the job completion. But since
qemu issues identical BLOCK_JOB_COMPLETE events regardless of whether
the job was cancelled (kept the original disk) or completed (pivoted
to the new disk), we have to track which of the two operations were
used to end the job. Furthermore, we'd like to avoid attempts to
end a job where we are already waiting on an earlier request to qemu
to end the job. Likewise, if we miss the qemu event (perhaps because
it arrived during a libvirtd restart), we still need enough state
recorded to be able to determine how to modify the domain XML once
we reconnect to qemu and manually learn whether the job still exists.
Although this patch doesn't actually fix the problem, it is a
preliminary step that makes it possible to track whether a job
has already begun steps towards completion.
* src/conf/domain_conf.h (virDomainDiskMirrorState): New enum.
(_virDomainDiskDef): Convert bool mirroring to new enum.
* src/conf/domain_conf.c (virDomainDiskDefParseXML)
(virDomainDiskDefFormat): Handle new values.
* src/qemu/qemu_process.c (qemuProcessHandleBlockJob): Adjust
client.
* src/qemu/qemu_driver.c (qemuDomainBlockPivot)
(qemuDomainBlockJobImpl): Likewise.
* docs/schemas/domaincommon.rng (diskMirror): Expose new values.
* docs/formatdomain.html.in (elementsDisks): Document it.
* tests/qemuxml2argvdata/qemuxml2argv-disk-mirror.xml: Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
Libvirt documents that the default entropy source for the 'random'
backend of a RNG device is /dev/random. Instead of storing and
propagating NULL across our code and checking it in multiple places fill
the default in the post parse callback and use that in the other places.
The previous commit 09d4d26 put the interleave at the wrong point;
it didn't allow interleaving with <memory>.
* docs/schema/domaincommon.rng (numatune): Fix interleave location.
* tests/qemuxml2argvdata/qemuxml2argv-numatune-memnode.xml: Adjust test.
Signed-off-by: Eric Blake <eblake@redhat.com>
