A new type to track USB addresses.
Every <controller type='usb' index='i'/> is represented by an
object of type virDomainUSBAddressHub located at buses[i].
Each of these hubs has up to 'nports' ports.
If a port is occupied, it has the corresponding bit set in
the 'ports' bitmap, e.g. port 1 would have the 0th bit set.
If there is a hub on this port, then hubs[i] will point
to this hub.
In preparation to tracking which USB addresses are occupied.
Introduce two helper functions for printing the port path
as a string and appending it to a virBuffer.
We had both and the only difference was that the latter also included
information about multifunction setting. The problem with that was that
we couldn't use functions made for only one of the structs (e.g.
parsing). To consolidate those two structs, use the one in virpci.h,
include that in domain_conf.h and add the multifunction member in it.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
There are two places in qemu_domain_address.c where we have a switch
statement to convert PCI controller models
(VIR_DOMAIN_CONTROLLER_MODEL_PCI*) into the connection type flag that
is matched when looking for an upstream connection for that model of
controller (VIR_PCI_CONNECT_TYPE_*). This patch makes a utility
function in conf/domain_addr.c to do that, so that when a new PCI
controller is added, we only need to add the new model-->connect-type
in a single place.
The flags used to determine which devices could be plugged into which
controllers were quite confusing, as they tried to create classes of
connections, then put particular devices into possibly multiple
classes, while sometimes setting multiple flags for the controllers
themselves. The attempt to have a single flag indicate, e.g. that a
root-port or a switch-downstream-port could connect was not only
confusing, it was leading to a situation where it would be impossible
to specify exactly the right combinations for a new controller.
The solution is for the VIR_PCI_CONNECT_TYPE_* flags to have a 1:1
correspondence with each type of PCI controller, plus a flag for a PCI
endpoint device and another for a PCIe endpoint device (the only
exception to this is that pci-bridge and pcie-expander-bus controllers
have their upstream connection classified as
VIR_PCI_CONNECT_TYPE_PCI_DEVICE since they can be plugged into
*exactly* the same ports as any endpoint device). Each device then
has a single flag for connect type (plus the HOTPLUG flag if that
device can e hotplugged), and each controller sets the CONNECT bits
for all controllers that can be plugged into it, as well as for either
type of endpoint device that can be plugged in (and the HOTPLUG flag
if it can accept hotplugged devices).
With this change, it is *slightly* easier to understand the matching
of connections (as long as you remember that the flag for a
device/upstream-facing connection of a controller is the same as that
device's type, while the flags for a controller's downstream
connections is the OR of all device types that can be plugged into
that controller). More importantly, it will be possible to correctly
specify what can be plugged into a pcie-switch-expander-bus, when
support for it is added.
We only support hotplugging SCSI controllers.
The USB and virtio-serial related code was never reachable because
this function was only called for VIR_DOMAIN_CONTROLLER_TYPE_SCSI
controllers.
This reverts commit ee0d97a and parts of commits 16db8d2
and d6d54cd1.
This controller can be connected only to a pcie-root-port or a
pcie-switch-downstream-port (which will be added in a later patch),
which is the reason for the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_PORT. A pcie-switch-upstream-port provides
32 ports (slot=0 to slot=31) on the downstream side, which can only
have pci controllers of model "pcie-switch-downstream-port" plugged
into them, which is the reason for the other new connect type
VIR_PCI_CONNECT_TYPE_PCIE_SWITCH.
This controller can be connected (at domain startup time only - not
hotpluggable) only to a port on the pcie root complex ("pcie-root" in
libvirt config), hence the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_ROOT. It provides a hotpluggable port that
will accept any PCI or PCIe device.
New attributes must be added to the controller <target> subelement for
this - chassis and port are guest-visible option values that will be
set by libvirt with values derived from the controller's index and pci
address information.
When support for the pcie-root and dmi-to-pci-bridge buses on a Q35
machinetype was added, I was concerned that even though qemu at the
time allowed plugging a PCI device into a PCIe port, that it might not
be supported in the future. To prevent painful backtracking in the
possible future where this happened, I disallowed such connections
except in a few specific cases requested by qemu developers (indicated
in the code with the flag VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG).
Now that a couple years have passed, there is a clear message from
qemu that there is no danger in allowing PCI devices to be plugged
into PCIe ports. This patch eliminates
VIR_PCI_CONNECT_TYPE_EITHER_IF_CONFIG and changes the code to always
allow PCI->PCIe or PCIe->PCI connection *when the PCI address is
specified in the config. (For newly added devices that haven't yet
been given a PCI address, the auto-placement still prefers using the
correct type of bus).
Create a sorted array of virtio-serial controllers.
Each of the elements contains the controller index
and a bitmap of available ports.
Buses are not tracked, because they aren't supported by QEMU.
Move sharable PCI handling functions to domain_addr.[ch], and
change theirs prefix from 'qemu' to 'vir':
- virDomainPCIAddressAsString;
- virDomainPCIAddressBusSetModel;
- virDomainPCIAddressEnsureAddr;
- virDomainPCIAddressFlagsCompatible;
- virDomainPCIAddressGetNextSlot;
- virDomainPCIAddressReleaseSlot;
- virDomainPCIAddressReserveAddr;
- virDomainPCIAddressReserveNextSlot;
- virDomainPCIAddressReserveSlot;
- virDomainPCIAddressSetFree;
- virDomainPCIAddressSetGrow;
- virDomainPCIAddressSlotInUse;
- virDomainPCIAddressValidate;
The only change here is function names, the implementation itself
stays untouched.
Extract common allocation code from DomainPCIAddressSetCreate
into virDomainPCIAddressSetAlloc.
Introduce new files (domain_addr.[ch]) to provide
an API for domain device handling that could be
shared across the drivers.
A list of data types were extracted and moved there:
qemuDomainPCIAddressBus -> virDomainPCIAddressBus
qemuDomainPCIAddressBusPtr -> virDomainPCIAddressBusPtr
_qemuDomainPCIAddressSet -> virDomainPCIAddressSet
qemuDomainPCIAddressSetPtr -> virDomainPCIAddressSetPtr
qemuDomainPCIConnectFlags -> virDomainPCIConnectFlags
Also, move the related definitions and macros.
