Firewall and network filtering in libvirt

There are three pieces of libvirt functionality which do network filtering of some type.

At a high level they are:

The virtual network driver

The typical configuration for guests is to use bridging of the physical NIC on the host to connect the guest directly to the LAN. In RHEL6 there is also the possibility of using macvtap/sr-iov and VEPA connectivity. None of this stuff plays nicely with wireless NICs, since they will typically silently drop any traffic with a MAC address that doesn't match that of the physical NIC.

Thus the virtual network driver in libvirt was invented. This takes the form of an isolated bridge device (ie one with no physical NICs enslaved). The TAP devices associated with the guest NICs are attached to the bridge device. This immediately allows guests on a single host to talk to each other and to the host OS (modulo host IPtables rules).

libvirt then uses iptables to control what further connectivity is available. There are three configurations possible for a virtual network at time of writing:

The latter 'forward' case requires the virtual network be on a separate sub-net from the main LAN, and that the LAN admin has configured routing for this subnet. In the future we intend to add support for IP subnetting and/or proxy-arp. This allows for the virtual network to use the same subnet as the main LAN and should avoid need for the LAN admin to configure special routing.

Libvirt will optionally also provide DHCP services to the virtual network using DNSMASQ. In all cases, we need to allow DNS/DHCP queries to the host OS. Since we can't predict whether the host firewall setup is already allowing this, we insert 4 rules into the head of the INPUT chain 

target     prot opt in     out     source               destination
ACCEPT     udp  --  virbr0 *       0.0.0.0/0            0.0.0.0/0           udp dpt:53
ACCEPT     tcp  --  virbr0 *       0.0.0.0/0            0.0.0.0/0           tcp dpt:53
ACCEPT     udp  --  virbr0 *       0.0.0.0/0            0.0.0.0/0           udp dpt:67
ACCEPT     tcp  --  virbr0 *       0.0.0.0/0            0.0.0.0/0           tcp dpt:67

Note we have restricted our rules to just the bridge associated with the virtual network, to avoid opening undesirable holes in the host firewall wrt the LAN/WAN.

The next rules depend on the type of connectivity allowed, and go in the main FORWARD chain:

The network filter driver

This driver provides a fully configurable network filtering capability that leverages ebtables, iptables and ip6tables. This was written by the libvirt guys at IBM and although its XML schema is defined by libvirt, the conceptual model is closely aligned with the DMTF CIM schema for network filtering:

http://www.dmtf.org/standards/cim/cim_schema_v2230/CIM_Network.pdf

The filters are managed in libvirt as a top level, standalone object. This allows the filters to then be referenced by any libvirt object that requires their functionality, instead tieing them only to use by guest NICs. In the current implementation, filters can be associated with individual guest NICs via the libvirt domain XML format. In the future we might allow filters to be associated with the virtual network objects. Further we're expecting to define a new 'virtual switch' object to remove the complexity of configuring bridge/sriov/vepa networking modes. This make also end up making use of network filters.

There are a new set of virsh commands for managing network filters:

There are equivalently named C APIs for each of these commands.

As with all objects libvirt manages, network filters are configured using an XML format. At a high level the format looks like this: 

<filter name='no-spamming' chain='XXXX'>
  <uuid>d217f2d7-5a04-0e01-8b98-ec2743436b74</uuid>

  <rule ...>
    ....
  </rule>

  <filterref filter='XXXX'/>
</filter>

Every filter has a name and UUID which serve as unique identifiers. A filter can have zero-or-more <rule> elements which are used to actually define network controls. Filters can be arranged into a DAG, so zero-or-more <filterref/> elements are also allowed. Cycles in the graph are not allowed.

The <rule> element is where all the interesting stuff happens. It has three attributes, an action, a traffic direction and an optional priority. eg: 

<rule action='drop' direction='out' priority='500'>

Within the rule there are a wide variety of elements allowed, which do protocol specific matching. Supported protocols currently include mac, arp, rarp, ip, ipv6, tcp/ip, icmp/ip, igmp/ip, udp/ip, udplite/ip, esp/ip, ah/ip, sctp/ip, tcp/ipv6, icmp/ipv6, igmp/ipv6, udp/ipv6, udplite/ipv6, esp/ipv6, ah/ipv6, sctp/ipv6. Each protocol defines what is valid inside the <rule> element. The general pattern though is: 

<protocol match='yes|no' attribute1='value1' attribute2='value2'/>

So, eg a TCP protocol, matching ports 0-1023 would be expressed as:

<tcp match='yes' srcportstart='0' srcportend='1023'/>

Attributes can included references to variables defined by the object using the rule. So the guest XML format allows each NIC to have a MAC address and IP address defined. These are made available to filters via the variables $IP and $MAC.

So to define a filter that prevents IP address spoofing we can simply match on source IP address != $IP like this: 

<filter name='no-ip-spoofing' chain='ipv4'>
  <rule action='drop' direction='out'>
    <ip match='no' srcipaddr='$IP' />
  </rule>
</filter>

I'm not going to go into details on all the other protocol matches you can do, because it'll take far too much space. You can read about the options here.

Out of the box in RHEL6/Fedora rawhide, libvirt ships with a set of default useful rules: 

# virsh nwfilter-list
UUID                                  Name
----------------------------------------------------------------
15b1ab2b-b1ac-1be2-ed49-2042caba4abb  allow-arp
6c51a466-8d14-6d11-46b0-68b1a883d00f  allow-dhcp
7517ad6c-bd90-37c8-26c9-4eabcb69848d  allow-dhcp-server
3d38b406-7cf0-8335-f5ff-4b9add35f288  allow-incoming-ipv4
5ff06320-9228-2899-3db0-e32554933415  allow-ipv4
db0b1767-d62b-269b-ea96-0cc8b451144e  clean-traffic
f88f1932-debf-4aa1-9fbe-f10d3aa4bc95  no-arp-spoofing
772f112d-52e4-700c-0250-e178a3d91a7a  no-ip-multicast
7ee20370-8106-765d-f7ff-8a60d5aaf30b  no-ip-spoofing
d5d3c490-c2eb-68b1-24fc-3ee362fc8af3  no-mac-broadcast
fb57c546-76dc-a372-513f-e8179011b48a  no-mac-spoofing
dba10ea7-446d-76de-346f-335bd99c1d05  no-other-l2-traffic
f5c78134-9da4-0c60-a9f0-fb37bc21ac1f  no-other-rarp-traffic
7637e405-4ccf-42ac-5b41-14f8d03d8cf3  qemu-announce-self
9aed52e7-f0f3-343e-fe5c-7dcb27b594e5  qemu-announce-self-rarp

Most of these are just building blocks. The interesting one here is 'clean-traffic'. This pulls together all the building blocks into one filter that you can then associate with a guest NIC. This stops the most common bad things a guest might try, IP spoofing, arp spoofing and MAC spoofing. To look at the rules for any of these just do: 

virsh nwfilter-dumpxml FILTERNAME|UUID

They are all stored in /etc/libvirt/nwfilter, but don't edit the files there directly. Use virsh nwfilter-define to update them. This ensures the guests have their iptables/ebtables rules recreated.

To associate the clean-trafffic filter with a guest, edit the guest XML config and change the <interface> element to include a <filterref> and also specify the whitelisted <ip address/> the guest is allowed to use: 

<interface type='bridge'>
  <mac address='52:54:00:56:44:32'/>
  <source bridge='br1'/>
  <ip address='10.33.8.131'/>
  <target dev='vnet0'/>
  <model type='virtio'/>
  <filterref filter='clean-traffic'/>
</interface>

If no <ip address> is included, the network filter driver will activate its 'learning mode'. This uses libpcap to snoop on network traffic the guest sends and attempts to identify the first IP address it uses. It then locks traffic to this address. Obviously this isn't entirely secure, but it does offer some protection against the guest being trojaned once up and running. In the future we intend to enhance the learning mode so that it looks for DHCPOFFERS from a trusted DHCP server and only allows the offered IP address to be used.

Now, how is all this implemented...?

The network filter driver uses a combination of ebtables, iptables and ip6tables, depending on which protocols are referenced in a filter. The out of the box 'clean-traffic' filter rules only require use of ebtables. If you want to do matching at tcp/udp/etc protocols (eg to add a new filter 'no-email-spamming' to block port 25), then iptables will also be used.

The driver attempts to keep its rules separate from those that the host admin might already have configured. So the first thing it does with ebtables, is to add two hooks in POSTROUTING and PREROUTING chains, to redirect traffic to custom chains. These hooks match on the TAP device name of the guest NIC, so they should not interact badly with any administrator defined rules: 

Bridge chain: PREROUTING, entries: 1, policy: ACCEPT
-i vnet0 -j libvirt-I-vnet0

Bridge chain: POSTROUTING, entries: 1, policy: ACCEPT
-o vnet0 -j libvirt-O-vnet0

To keep things managable and easy to follow, the driver will then create further sub-chains for each protocol then it needs to match against: 

Bridge chain: libvirt-I-vnet0, entries: 5, policy: ACCEPT
-p IPv4 -j I-vnet0-ipv4
-p ARP -j I-vnet0-arp
-p 0x8035 -j I-vnet0-rarp
-p 0x835 -j ACCEPT
-j DROP

Bridge chain: libvirt-O-vnet0, entries: 4, policy: ACCEPT
-p IPv4 -j O-vnet0-ipv4
-p ARP -j O-vnet0-arp
-p 0x8035 -j O-vnet0-rarp
-j DROP

Finally, here comes the actual implementation of the filters. This example shows the 'clean-traffic' filter implementation. I'm not going to explain what this is doing now. :-) 

Bridge chain: I-vnet0-ipv4, entries: 2, policy: ACCEPT
-s ! 52:54:0:56:44:32 -j DROP
-p IPv4 --ip-src ! 10.33.8.131 -j DROP

Bridge chain: O-vnet0-ipv4, entries: 1, policy: ACCEPT
-j ACCEPT

Bridge chain: I-vnet0-arp, entries: 6, policy: ACCEPT
-s ! 52:54:0:56:44:32 -j DROP
-p ARP --arp-mac-src ! 52:54:0:56:44:32 -j DROP
-p ARP --arp-ip-src ! 10.33.8.131 -j DROP
-p ARP --arp-op Request -j ACCEPT
-p ARP --arp-op Reply -j ACCEPT
-j DROP

Bridge chain: O-vnet0-arp, entries: 5, policy: ACCEPT
-p ARP --arp-op Reply --arp-mac-dst ! 52:54:0:56:44:32 -j DROP
-p ARP --arp-ip-dst ! 10.33.8.131 -j DROP
-p ARP --arp-op Request -j ACCEPT
-p ARP --arp-op Reply -j ACCEPT
-j DROP

Bridge chain: I-vnet0-rarp, entries: 2, policy: ACCEPT
-p 0x8035 -s 52:54:0:56:44:32 -d Broadcast --arp-op Request_Reverse --arp-ip-src 0.0.0.0 --arp-ip-dst 0.0.0.0 --arp-mac-src 52:54:0:56:44:32 --arp-mac-dst 52:54:0:56:44:32 -j ACCEPT
-j DROP

Bridge chain: O-vnet0-rarp, entries: 2, policy: ACCEPT
-p 0x8035 -d Broadcast --arp-op Request_Reverse --arp-ip-src 0.0.0.0 --arp-ip-dst 0.0.0.0 --arp-mac-src 52:54:0:56:44:32 --arp-mac-dst 52:54:0:56:44:32 -j ACCEPT
-j DROP

NB, we would have liked to include the prefix 'libvirt-' in all of our chain names, but unfortunately the kernel limits names to a very short maximum length. So only the first two custom chains can include that prefix. The others just include the TAP device name + protocol name.

If I define a new filter 'no-spamming' and then add this to the 'clean-traffic' filter, I can illustrate how iptables usage works: 

# cat > /root/spamming.xml <<EOF
<filter name='no-spamming' chain='root'>
  <uuid>d217f2d7-5a04-0e01-8b98-ec2743436b74</uuid>
  <rule action='drop' direction='out' priority='500'>
    <tcp dstportstart='25' dstportend='25'/>
  </rule>
</filter>
EOF
# virsh nwfilter-define /root/spamming.xml
# virsh nwfilter-edit clean-traffic

...add <filterref filter='no-spamming'/>

All active guests immediately have their iptables/ebtables rules rebuilt.

The network filter driver deals with iptables in a very similar way. First it separates out its rules from those the admin may have defined, by adding a couple of hooks into the INPUT/FORWARD chains: 

Chain INPUT (policy ACCEPT 13M packets, 21G bytes)
target           prot opt in     out     source               destination
libvirt-host-in  all  --  *      *       0.0.0.0/0            0.0.0.0/0

Chain FORWARD (policy ACCEPT 5532K packets, 3010M bytes)
target           prot opt in     out     source               destination
libvirt-in       all  --  *      *       0.0.0.0/0            0.0.0.0/0
libvirt-out      all  --  *      *       0.0.0.0/0            0.0.0.0/0
libvirt-in-post  all  --  *      *       0.0.0.0/0            0.0.0.0/0

These custom chains then do matching based on the TAP device name, so they won't open holes in the admin defined matches for the LAN/WAN (if any). 

Chain libvirt-host-in (1 references)
  target     prot opt in     out     source               destination
  HI-vnet0   all  --  *      *       0.0.0.0/0            0.0.0.0/0           [goto] PHYSDEV match --physdev-in vnet0

Chain libvirt-in (1 references)
  target     prot opt in     out     source               destination
  FI-vnet0   all  --  *      *       0.0.0.0/0            0.0.0.0/0           [goto] PHYSDEV match --physdev-in vnet0

Chain libvirt-in-post (1 references)
  target     prot opt in     out     source               destination
  ACCEPT     all  --  *      *       0.0.0.0/0            0.0.0.0/0           PHYSDEV match --physdev-in vnet0

Chain libvirt-out (1 references)
  target     prot opt in     out     source               destination
  FO-vnet0   all  --  *      *       0.0.0.0/0            0.0.0.0/0           [goto] PHYSDEV match --physdev-out vnet0

Finally, we can see the interesting bit which is the actual implementation of my filter to block port 25 access: 

Chain FI-vnet0 (1 references)
  target     prot opt in     out     source               destination
  DROP       tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           tcp dpt:25

Chain FO-vnet0 (1 references)
  target     prot opt in     out     source               destination
  DROP       tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           tcp spt:25

Chain HI-vnet0 (1 references)
  target     prot opt in     out     source               destination
  DROP       tcp  --  *      *       0.0.0.0/0            0.0.0.0/0           tcp dpt:25

One thing in looking at this you may notice is that if there are many guests all using the same filters, we will be duplicating the iptables rules over and over for each guest. This is merely a limitation of the current rules engine implementation. At the libvirt object modelling level you can clearly see we've designed the model so filter rules are defined in one place, and indirectly referenced by guests. Thus it should be possible to change the implementation in the future so we can share the actual iptables/ebtables rules for each guest to create a more scalable system. The stuff in current libvirt is more or less the very first working implementation we've had of this, so there's not been much optimization work done yet.

Also notice that at the XML level we don't expose the fact we are using iptables or ebtables at all. The rule definition is done in terms of network protocols. Thus if we ever find a need, we could plug in an alternative implementation that calls out to a different firewall implementation instead of ebtables/iptables (providing that implementation was suitably expressive of course)

Finally, in terms of problems we have in deployment. The biggest problem is that if the admin does service iptables restart all our work gets blown away. We've experimented with using lokkit to record our custom rules in a persistent config file, but that caused different problem. Admins who were not using lokkit for their config found that all their own rules got blown away. So we threw away our lokkit code. Instead we document that if you run service iptables restart, you need to send SIGHUP to libvirt to make it recreate its rules.

More in depth documentation on this is here.