Now that we dropped EPOLLET, we'll keep getting EPOLLRDHUP, and
possibly EPOLLIN, even if there's nothing to read anymore.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
EPOLLHUP just means we shut down one side of the connection on
*one* socket: remember, we have two sockets here.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
...throughput isn't everything: this leads (of course) to horrible
latency with small, sparse messages. As a consequence, there's no
need to set TCP_NODELAY either.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
If we're at the first message in a batch, it's safe to get the
window value from it, and there's no need to subtract anything for
a comparison on that's not even done -- we'll override it later in
any case if we find messages with a higher ACK sequence number.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
...tcp_handler_splice() doesn't guarantee we read all the available
data, the sending buffer might be full.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Checking it only when the cached value is smaller than the current
window of the receiver is not enough: it might shrink further while
the receiver window is growing.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
If pasta created the namespace, it's probably expected that processes
started in the same namespace are terminated once pasta exits. Scan
procfs namespace links for corresponding processes, send SIGQUIT and
SIGKILL (after one second) if found.
While at it, make the signal handler reap otherwise-zombies resulting
from clone().
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
If we couldn't write the whole batch of received packets to the socket,
and we have missing segments, we still need to request their
retransmission right away, otherwise it will take ages for the guest to
figure out we're missing them.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
...instead of waiting for the remote peer to do that -- it's
especially important in case we request retransmissions from the
guest, but it also helps speeding up slow start. This should
probably be a configurable behaviour in the future.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Seen with iperf3: a control connection is established, no data flows
for a while, all segments are acknowledged. The socket starts closing
it, and we immediately time out because the last ACK from tap was one
minute before that.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Seen with iperf3: the first packet from socket (data connection) is
65520 bytes and doesn't fit in the window.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Flooding a virtio-net interface connected to a socket back-end results
in a TX stall I'm still debugging. The stall goes away by setting a
higher value for x-txburst (256 by default).
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
This fixes a number of issues found with some heavier testing with
uperf and neper:
- in most closing states, we can still accept data, check for EPOLLIN
when appropriate
- introduce a new state, ESTABLISHED_SOCK_FIN_SENT, to track the fact
we already sent a FIN segment to the tap device, for proper sequence
number bookkeeping
- for pasta mode only: spliced connections also need tracking of
(inferred) FIN segments and clean half-pipe shutdowns
- streamline resetting epoll_wait bitmaps with a new function,
tcp_tap_epoll_mask(), instead of repeating the logic all over the
place
- set EPOLLET for tap connections too, whenever we are waiting for
EPOLLRDHUP or an event from the tap to proceed with data transfer,
to avoid useless loops with EPOLLIN set
- impose an additional limit on the sending window advertised to the
guest, given by SO_SNDBUF: it makes no sense to completely fill
the sending buffer and send a zero window: stop a bit before we
hit that
- handle *all* interrupted system calls as needed
- simplify the logic for reordering of out-of-order segments received
from tap: it's not a corner case, and the previous logic allowed
for deadloops
- fix comparison of seen IPv4 address when we get a new connection
from a socket directed to the configured guest address
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
...this allows processes running as the only group available in the
namespace to create ICMP Echo sockets.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Before introducing options, the default behaviour in passt mode was
to forward all ports, to run in foreground and to log to stderr.
Make it a bit more convenient to restore that at build time.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
This went lost in a recent rework: if the guest wants to connect
directly to the host, it can use the address of the default gateway.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Similarly to the handling introduced by commit "tcp: Proper error
handling for sendmmsg() to UNIX domain socket" for TCP, we need to
deal with partial sendmmsg() failures for UDP as well.
Here, we can lose messages, but we need to make sure that the last
message is delivered completely, otherwise qemu will fail to
reassemble further packets. For UDP, this is somewhat complicated
by the fact that one message might include multiple datagrams, and
we need to respect message boundaries: go through headers, and
calculate what we need to re-send, if anything.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
This enables CirrOS with udhcpc to set up a route to a gateway
that's not on the assigned subnet, together with:
https://bugs.launchpad.net/cirros/+bug/1190372
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
DHCP clients might try to resolve the assigned address to check if it's
already in use: don't resolve the configured IPv4 address.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Depending on the configuration, the host might have the same address.
Don't answer them to avoid a duplicate IP address detection.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
And while at it, remove some attributes that are not needed anymore
after introducing command line options.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Once we're past the IA_NA or IA_TA option itself, before we start
looking for IA_ADDR suboptions, we need to subtract the length
of the option we parsed so far, otherwise we might end up reading
past the end of the message, or miss some parts.
While at it, streamline calculations in dhcpv6_opt().
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
