The current MSI-X implementation completely ignores the values found
in the Vector Control register related to a specific vector, and never
updates the Pending Bit Array.
According to the PCI specification, MSI-X vectors can be masked
through the Vector Control register on bit 0. If this bit is set,
the device should not inject any MSI message. When the device
runs into such situation, it must not inject the interrupt, but
instead it must update the bit corresponding to the vector number
in the Pending Bit Array.
Later on, if/when the Vector Control register is updated, and if
the bit 0 is flipped from 0 to 1, the device must look into the PBA
to find out if there was a pending interrupt for this specific
vector. If that's the case, an MSI message is injected and the
bit from the PBA is cleared.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
As mentioned in the PCI specification:
If a dedicated Base Address register is not feasible, it is
recommended that a function isolate the MSI-X structures from
the non-MSI-X structures with aligned 8 KB ranges rather than
the mandatory aligned 4 KB ranges.
That's why this patch ensures that each structure present on the
BAR is 8KiB aligned.
It also fixes the MSI-X table and PBA sizes so that they can support
up to 2048 vectors, as specified for MSI-X.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to factorize the complexity brought by closures, this commit
merges IrqClosure and MsixClosure into a generic InterruptDelivery one.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
In order to allow virtio-pci devices to use MSI-X messages instead
of legacy pin based interrupts, this patch implements the MSI-X
support for cloud-hypervisor. The VMM code and virtio-pci bits have
been modified based on the "msix" module previously added to the pci
crate.
Fixes#12
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Because we cannot always assume the irq fd will be the way to send
an IRQ to the guest, this means we cannot make the assumption that
every virtio device implementation should expect an EventFd to
trigger an IRQ.
This commit organizes the code related to virtio devices so that it
now expects a Rust closure instead of a known EventFd. This lets the
caller decide what should be done whenever a device needs to trigger
an interrupt to the guest.
The closure will allow for other type of interrupt mechanism such as
MSI to be implemented. From the device perspective, it could be a
pin based interrupt or an MSI, it does not matter since the device
will simply call into the provided callback, passing the appropriate
Queue as a reference. This design keeps the device model generic.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Most of the code is taken from crosvm(bbd24c5) but is modified to
be adapted to the current VirtioDevice definition and epoll
implementation.
A new command option '--rng' is provided and it gives one the option
to override the entropy source which is /dev/urandom by default.
Signed-off-by: Chao Peng <chao.p.peng@linux.intel.com>
In order to provide connectivity through network interface between
host and guest, this patch introduces the virtio-net backend.
This code is based on Firecracker commit
d4a89cdc0bd2867f821e3678328dabad6dd8b767
It is a trimmed down version of the original files as it removes the
rate limiter support. It has been ported to support vm-memory crate
and the epoll handler has been modified in order to run a dedicated
epoll loop from the device itself. This epoll loop runs in its own
dedicated thread.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
As it is necessary to return the interrupt EventFD and the queue EventFD
to the transport layer upon reset the activate function has been
modified to clone these descriptors as well as the underlying disk
itself.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
If the driver triggers a reset by writing zero into the status register
then reset the underlying device if supported. A device reset also
requires resetting various aspects of the queue.
In order to be able to do a subsequent reactivate it is required to
reclaim certain resources (interrupt and queue EventFDs.) If a device
reset is requested by the driver but the underlying device does not
support it then generate an error as the driver would not be able to
configure it anyway.
Signed-off-by: Rob Bradford <robert.bradford@intel.com>
Add the BSD and Apache license.
Make all crosvm references point to the BSD license.
Add the right copyrights and identifier to our VMM code.
Add Intel copyright to the vm-virtio and pci crates.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
After the virtio-blk device support has been introduced in the
previous commit, the vmm need to rely on this new device to boot
from disk images instead of initrd built into the kernel.
In order to achieve the proper support of virtio-blk, this commit
had to handle a few things:
- Register an ioevent fd for each virtqueue. This important to be
notified from the virtio driver that something has been written
on the queue.
- Fix the retrieval of 64bits BAR address. This is needed to provide
the right address which need to be registered as the notification
address from the virtio driver.
- Fix the write_bar and read_bar functions. They were both assuming
to be provided with an address, from which they were trying to
find the associated offset. But the reality is that the offset is
directly provided by the Bus layer.
- Register a new virtio-blk device as a virtio-pci device from the
vm.rs code. When the VM is started, it expects a block device to
be created, using this block device as the VM rootfs.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
This commit introduces the virtio-blk backend implementation, which is
the first device implementing the VirtioDevice trait.
Signed-off-by: Sebastien Boeuf <sebastien.boeuf@intel.com>
Copied from crosvm 107edb3e with one main modification: VirtioPciDevice
implements BusDevice.
We need this modification because it is the only way for us to be able
to add a VirtioPciDevice to the MMIO bus. Bus insertion takes a
BusDevice. The fact that VirtioPciDevice implements PciDevice which
itself implements BusDevice does not mean that Rust will automatically
downcast a VirtioPciDevice into a BusDevice.
crosvm works around that issue by having the PCI, virtio and BusDevice
implementations in the same crate.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copied from Firecracker 17a9089d for the queue implementation and from
crosvm 107edb3e for the device Trait. The device trait has some PCI
specific methods hence its crosvm origin.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
