Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
This patch teaches testutil how to read multi-line input files with
backspace-newline line continuation markers.
The patch also breaks up all the single-line arguments test input files into
multi-line files with lines shorter than 80 characters.
To try and ensure that people upgrading from old QEMU get guests
with the same PCI device ordering, change the way we assign addrs
to match QEMU's default order. This should make Windows less
annoyed.
* src/qemu/qemu_conf.c: Follow QEMU's default PCI ordering
logic when assigning addresses
* tests/*.args: Update for changed PCI addresses
We already use the '-nodefaults' command line arg with QEMU to stop
it adding any default devices to guests. Unfortunately, QEMU will
load global config files from /etc/qemu that may also add default
devices. These aren't blocked by '-nodefaults', so we need to also
add the '-nodefconfig' arg to prevent that.
Unfortunately these global config files are also used to define
custom CPU models. So in blocking global hardware device addition
we also block definitions of new CPU models. Libvirt doesn't know
about these custom CPU models though, so it would never make use
of them anyway. Thus blocking them via -nodefconfig isn't a show
stopping problem. We would need to expand libvirt's own CPU model
XML database to support these instead.
* src/qemu/qemu_conf.c: Add '-nodefconfig' if available
* tests/qemuxml2argvdata/: Add '-nodefconfig' to all data files which
have '-nodefaults' present
Replace
-balloon virtio
With
-device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3
This allows it to get correct assigned PCI address as declared in
previous patch
* src/qemu/qemu_conf.c: Convert Virtio ballon to -device and
give it an explicit PCI address
* tests/qemuxml2argvdata/qemuxml2argv-*args: Add in virtio balloon
where appropriate
The previous syntax was severely limited in its options
-usbdevice disk:/home/berrange/output.img
The new syntax is the same as for other disk types
-drive file=/home/berrange/output.img,if=none,id=usb-1,index=1
-device usb-storage,drive=usb-1
Again, the index= arg is wrong here, and will be removed in a
later merge
