So far, we are allowing /dev/vfio/vfio in the devices cgroup
unconditionally (and creating it in the namespace too). Even if
domain has no hostdev assignment configured. This is potential
security hole. Therefore, when starting the domain (or
hotplugging a hostdev) create & allow /dev/vfio/vfio too (if
needed).
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Since these two functions are nearly identical (with
qemuSetupHostdevCgroup actually calling virCgroupAllowDevicePath)
we can have one function call the other and thus de-duplicate
some code.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
The bare fact that mnt namespace is available is not enough for
us to allow/enable qemu namespaces feature. There are other
requirements: we must copy all the ACL & SELinux labels otherwise
we might grant access that is administratively forbidden or vice
versa.
At the same time, the check for namespace prerequisites is moved
from domain startup time to qemu.conf parser as it doesn't make
much sense to allow users to start misconfigured libvirt just to
find out they can't start a single domain.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
These functions do not need to see the whole virDomainDiskDef.
Moreover, they are going to be called from places where we don't
have access to the full disk definition. Sticking with
virStorageSource is more than enough.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
So far we allow to set MTU for libvirt networks. However, not all
domain interfaces have to be plugged into a libvirt network and
even if they are, they might want to have a different MTU (e.g.
for testing purposes).
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1405269
If a secret was not provided for what was determined to be a LUKS
encrypted disk (during virStorageFileGetMetadata processing when
called from qemuDomainDetermineDiskChain as a result of hotplug
attach qemuDomainAttachDeviceDiskLive), then do not attempt to
look it up (avoiding a libvirtd crash) and do not alter the format
to "luks" when adding the disk; otherwise, the device_add would
fail with a message such as:
"unable to execute QEMU command 'device_add': Property 'scsi-hd.drive'
can't find value 'drive-scsi0-0-0-0'"
because of assumptions that when the format=luks that libvirt would have
provided the secret to decrypt the volume.
Access to unlock the volume will thus be left to the application.
When attaching a device to a domain that's using separate mount
namespace we must maintain /dev entries in order for qemu process
to see them.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When attaching a device to a domain that's using separate mount
namespace we must maintain /dev entries in order for qemu process
to see them.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When attaching a device to a domain that's using separate mount
namespace we must maintain /dev entries in order for qemu process
to see them.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
When attaching a device to a domain that's using separate mount
namespace we must maintain /dev entries in order for qemu process
to see them.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Prime time. When it comes to spawning qemu process and
relabelling all the devices it's going to touch, there's inherent
race with other applications in the system (e.g. udev). Instead
of trying convincing udev to not touch libvirt managed devices,
we can create a separate mount namespace for the qemu, and mount
our own /dev there. Of course this puts more work onto us as we
have to maintain /dev files on each domain start and device
hot(un-)plug. On the other hand, this enhances security also.
From technical POV, on domain startup process the parent
(libvirtd) creates:
/var/lib/libvirt/qemu/$domain.dev
/var/lib/libvirt/qemu/$domain.devpts
The child (which is going to be qemu eventually) calls unshare()
to create new mount namespace. From now on anything that child
does is invisible to the parent. Child then mounts tmpfs on
$domain.dev (so that it still sees original /dev from the host)
and creates some devices (as explained in one of the previous
patches). The devices have to be created exactly as they are in
the host (including perms, seclabels, ACLs, ...). After that it
moves $domain.dev mount to /dev.
What's the $domain.devpts mount there for then you ask? QEMU can
create PTYs for some chardevs. And historically we exposed the
host ends in our domain XML allowing users to connect to them.
Therefore we must preserve devpts mount to be shared with the
host's one.
To make this patch as small as possible, creating of devices
configured for domain in question is implemented in next patches.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
qemuDomainObjExitAgent is unsafe.
First it accesses domain object without domain lock.
Second it uses outdated logic that goes back to commit 79533da1 of
year 2009 when code was quite different. (unref function
instead of unreferencing only unlocked and disposed object
in case of last reference and leaved unlocking to the caller otherwise).
Nowadays this logic may lead to disposing locked object
i guess.
Another problem is that the callers of qemuDomainObjEnterAgent
use domain object again (namely priv->agent) without domain lock.
This patch address these two problems.
qemuDomainGetAgent is dropped as unused.
Detect on reconnect to a running qemu VM whether the alias of a
hotpluggable memory device (dimm) does not match the dimm slot number
where it's connected to. This is necessary as qemu is actually
considering the alias as machine ABI used to connect the backend object
to the dimm device.
This will require us to keep them consistent so that we can reliably
restore them on migration. In some situations it was currently possible
to create a mismatched configuration and qemu would refuse to restore
the migration stream.
To avoid breaking existing VMs we'll need to keep the old algorithm
though.
Add the secret object so the 'passwordid=' can be added if the command line
if there's a secret defined in/on the host for TCP chardev TLS objects.
Preparation for the secret involves adding the secinfo to the char source
device prior to command line processing. There are multiple possibilities
for TCP chardev source backend usage.
Add test for at least a serial chardev as an example.
Adding a field to the domain's private vcpu object to hold the halted
state information.
Adding two functions in support of the halted state:
- qemuDomainGetVcpuHalted: retrieve the halted state from a
private vcpu object
- qemuDomainRefreshVcpuHalted: obtain the per-vcpu halted states
via qemu monitor and store the results in the private vcpu objects
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Reviewed-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Reviewed-by: Hao QingFeng <haoqf@linux.vnet.ibm.com>
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Add an optional "tls='yes|no'" attribute for a TCP chardev.
For QEMU, this will allow for disabling the host config setting of the
'chardev_tls' for a domain chardev channel by setting the value to "no" or
to attempt to use a host TLS environment when setting the value to "yes"
when the host config 'chardev_tls' setting is disabled, but a TLS environment
is configured via either the host config 'chardev_tls_x509_cert_dir' or
'default_tls_x509_cert_dir'
Signed-off-by: John Ferlan <jferlan@redhat.com>
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Commit id '5f2a132786' should have placed the data in the host source
def structure since that's also used by smartcard, redirdev, and rng in
order to provide a backend tcp channel. The data in the private structure
will be necessary in order to provide the secret properly.
This also renames the previous names from "Chardev" to "ChrSource" for
the private data structures and API's
Modeled after the qemuDomainHostdevPrivatePtr (commit id '27726d8c'),
create a privateData pointer in the _virDomainChardevDef to allow storage
of private data for a hypervisor in order to at least temporarily store
secret data for usage during qemuBuildCommandLine.
NB: Since the qemu_parse_command (qemuParseCommandLine) code is not
expecting to restore the secret data, there's no need to add code
code to handle this new structure there.
Signed-off-by: John Ferlan <jferlan@redhat.com>
This improves commit 706b5b6277 in a way that we check qemu capabilities
instead of what architecture we are running on to detect whether we can
use *virtio-vga* model or not. This is not a case only for arm/aarch64.
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Sometimes adding a separate variable to access vm->privateData is not
necessary. Add a macro that will do the typecasting rather than having
to add a temp variable to force the compiler to typecast it.
Put it into qemuDomainPrepareShmemChardev() so it can be used later.
Also don't fill in the path unless the server option is enabled.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
When migration fails, we need to poke QEMU monitor to check for a reason
of the failure. We did this using query-migrate QMP command, which is
not supposed to return any meaningful result on the destination side.
Thus if the monitor was still functional when we detected the migration
failure, parsing the answer from query-migrate always failed with the
following error message:
"info migration reply was missing return status"
This irrelevant message was then used as the reason for the migration
failure replacing any message we might have had.
Let's use harmless query-status for poking the monitor to make sure we
only get an error if the monitor connection is broken.
https://bugzilla.redhat.com/show_bug.cgi?id=1374613
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
The vcpu order information is extracted only for hotpluggable entities,
while vcpu definitions belonging to the same hotpluggable entity need
to all share the order information.
We also can't overwrite it right away in the vcpu info detection code as
the order is necessary to add the hotpluggable vcpus enabled on boot in
the correct order.
The helper will store the order information in places where we are
certain that it's necessary.
Introduce a new migration cookie flag that will be used for any
configurations that are not compatible with libvirt that would not
support the specific vcpu hotplug approach. This will make sure that old
libvirt does not fail to reproduce the configuration correctly.
Similarly to devices the guest may allow unplug of the VCPU if libvirt
is down. To avoid problems, refresh the vcpu state on reconnect. Don't
mess with the vcpu state otherwise.
Now that the monitor code gathers all the data we can extract it to
relevant places either in the definition or the private data of a vcpu.
As only thread id is broken for TCG guests we may extract the rest of
the data and just skip assigning of the thread id. In case where qemu
would allow cpu hotplug in TCG mode this will make it work eventually.
Validate the presence of the thread id according to state of the vCPU
rather than just checking the vCPU count. Additionally put the new
validation code into a separate function so that the information
retrieval can be split from the validation.
Until now we simply errored out when the translation from pool+volume
failed. However, we should instead check whether that disk is needed or
not since there is an option for that.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1168453
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Dropping the caching of ccw address set.
The cached set is not required anymore, because the set is now being
recalculated from the domain definition on demand, so the cache
can be deleted.
Dropping the caching of virtio serial address set.
The cached set is not required anymore, because the set is now being
recalculated from the domain definition on demand, so the cache
can be deleted.
Credit goes to Cole Robinson.
Introduce a helper to help determine if a disk src could be possibly used
for a disk secret... Going to need this for hot unplug.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Put it into separate function called qemuDomainPrepareChannel() and call
it from the new qemuProcessPrepareDomain().
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Along with the virtlogd addition of the log file appending API implement
a helper for logging one-shot entries to the log file including the
fallback approach of using direct file access.
This will be used for noting the shutdown of the qemu proces and
possibly other actions such as VM migration and other critical VM
lifecycle events.
Based on some digital archaeology performed by jtomko, it's been determined
that the persistentAddrs variable is no longer necessary...
The variable was added by:
commit 141dea6bc7
CommitDate: 2010-02-12 17:25:52 +0000
Add persistence of PCI addresses to QEMU
Where it was set to 0 on domain startup if qemu did not support the
QEMUD_CMD_FLAG_DEVICE capability, to clear the addresses at shutdown,
because QEMU might make up different ones next time.
As of commit f5dd58a608
CommitDate: 2012-07-11 11:19:05 +0200
qemu: Extended qemuDomainAssignAddresses to be callable from
everywhere.
this was broken, when the persistentAddrs = 0 assignment was moved
inside qemuDomainAssignPCIAddresses and while it pretends to check
for !QEMU_CAPS_DEVICE, its parent qemuDomainAssignAddresses is only
called if QEMU_CAPS_DEVICE is present.
Extract information for all disks and update tray state and source only
for removable drives. Additionally store whether a drive is removable
and whether it has a tray.
Extract whether a given drive has a tray and whether there is no image
inserted.
Negative logic for the image insertion is chosen so that the flag is set
only if we are certain of the fact.
Rather than returning a "char *" indicating perhaps some sized set of
characters that is NUL terminated, alter the function to return 0 or -1
for success/failure and add two parameters to handle returning the
buffer and it's size.
The function no longer encodes the returned secret, rather it returns
the unencoded secret forcing callers to make the necessary adjustments.
Alter the callers to handle the adjusted model.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Extract the relevant parts of the existing checker and reuse them for
blockcopy since copying to a non-block device creates an invalid
configuration.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1209802
Add the data structure and infrastructure to support an initialization
vector (IV) secrets. The IV secret generation will need to have access
to the domain private master key, so let's make sure the prepare disk
and hostdev functions can accept that now.
Anywhere that needs to make a decision over which secret type to use
in order to fill in or use the IV secret has a switch added.
Signed-off-by: John Ferlan <jferlan@redhat.com>
A recent review of related changes noted that we should split the creation
(or generation) of the master key into the qemuProcessPrepareDomain and leave
the writing of the master key for qemuProcessPrepareHost.
Made the adjustment and modified some comments to functions that have
changed calling parameters, but didn't change the intro doc.
Signed-off-by: John Ferlan <jferlan@redhat.com>
From a review after push, add the "_TYPE" into the name.
Also use qemuDomainSecretInfoType in the struct rather than int
with the comment field containing the struct name
Signed-off-by: John Ferlan <jferlan@redhat.com>
Similar to the qemuDomainSecretDiskPrepare, generate the secret
for the Hostdev's prior to call qemuProcessLaunch which calls
qemuBuildCommandLine. Additionally, since the secret is not longer
added as part of building the command, the hotplug code will need
to make the call to add the secret in the hostdevPriv.
Since this then is the last requirement to pass a virConnectPtr
to qemuBuildCommandLine, we now can remove that as part of these
changes. That removal has cascading effects through various callers.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Modeled after the qemuDomainDiskPrivatePtr logic, create a privateData
pointer in the _virDomainHostdevDef to allow storage of private data
for a hypervisor in order to at least temporarily store auth/secrets
data for usage during qemuBuildCommandLine.
NB: Since the qemu_parse_command (qemuParseCommandLine) code is not
expecting to restore the auth/secret data, there's no need to add
code to handle this new structure there.
Updated copyrights for modules touched. Some didn't have updates in a
couple years even though changes have been made.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Rather than needing to pass the conn parameter to various command
line building API's, add qemuDomainSecretPrepare just prior to the
qemuProcessLaunch which calls qemuBuilCommandLine. The function
must be called after qemuProcessPrepareHost since it's expected
to eventually need the domain masterKey generated during the prepare
host call. Additionally, future patches may require device aliases
(assigned during the prepare domain call) in order to associate
the secret objects.
The qemuDomainSecretDestroy is called after the qemuProcessLaunch
finishes in order to clear and free memory used by the secrets
that were recently prepared, so they are not kept around in memory
too long.
Placing the setup here is beneficial for future patches which will
need the domain masterKey in order to generate an encrypted secret
along with an initialization vector to be saved and passed (since
the masterKey shouldn't be passed around).
Finally, since the secret is not added during command line build,
the hotplug code will need to get the secret into the private disk data.
Signed-off-by: John Ferlan <jferlan@redhat.com>
Introduce a new private structure to hold qemu domain auth/secret data.
This will be stored in the qemuDomainDiskPrivate as a means to store the
auth and fetched secret data rather than generating during building of
the command line.
The initial changes will handle the current username and secret values
for rbd and iscsi disks (in their various forms). The rbd secret is
stored as a base64 encoded value, while the iscsi secret is stored as
a plain text value. Future changes will store encoded/encrypted secret
data as well as an initialization vector needed to be given to qemu
in order to decrypt the encoded password along with the domain masterKey.
The inital assumption will be that VIR_DOMAIN_SECRET_INFO_PLAIN is
being used.
Although it's expected that the cleanup of the secret data will be
done immediately after command line generation, reintroduce the object
dispose function qemuDomainDiskPrivateDispose to handle removing
memory associated with the structure for "normal" cleanup paths.
Signed-off-by: John Ferlan <jferlan@redhat.com>
When creating the master key, we used mode 0600 (which we should) but
because we were creating it as root, the file is not readable by any
qemu running as non-root. Fortunately, it's just a matter of labelling
the file. We are generating the file path few times already, so let's
label it in the same function that has access to the path already.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Similarly to the DEVICE_DELETED event we will be able to tell when
unplug of certain device types will be rejected by the guest OS. Wire up
the device deletion signalling code to allow handling this.
Add a masterKey and masterKeyLen to _qemuDomainObjPrivate to store a
random domain master key and its length in order to support the ability
to encrypt/decrypt sensitive data shared between libvirt and qemu. The
key will be base64 encoded and written to a file to be used by the
command line building code to share with qemu.
New API's from this patch:
qemuDomainGetMasterKeyFilePath:
Return a path to where the key is located
qemuDomainWriteMasterKeyFile: (private)
Open (create/trunc) the masterKey path and write the masterKey
qemuDomainMasterKeyReadFile:
Using the master key path, open/read the file, and store the
masterKey and masterKeyLen. Expected use only from qemuProcessReconnect
qemuDomainGenerateRandomKey: (private)
Generate a random key using available algorithms
The key is generated either from the gnutls_rnd function if it
exists or a less cryptographically strong mechanism using
virGenerateRandomBytes
qemuDomainMasterKeyRemove:
Remove traces of the master key, remove the *KeyFilePath
qemuDomainMasterKeyCreate:
Generate the domain master key and save the key in the location
returned by qemuDomainGetMasterKeyFilePath.
This API will first ensure the QEMU_CAPS_OBJECT_SECRET is set
in the capabilities. If not, then there's no need to generate
the secret or file.
The creation of the key will be attempted from qemuProcessPrepareHost
once the libDir directory structure exists.
The removal of the key will handled from qemuProcessStop just prior
to deleting the libDir tree.
Since the key will not be written out to the domain object XML file,
the qemuProcessReconnect will read the saved file and restore the
masterKey and masterKeyLen.
The paths have the domain ID in them. Without cleaning them, they would
contain the same ID even after multiple restarts. That could cause
various problems, e.g. with access.
Add function qemuDomainClearPrivatePaths() for this as a counterpart of
qemuDomainSetPrivatePaths().
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
If use of virtlogd is enabled, then use it for backing the
character device log files too. This avoids the possibility
of a guest denial of service by writing too much data to
the log file.
With a very old QEMU which doesn't support events we need to explicitly
call qemuMigrationSetOffline at the end of migration to update our
internal state. On the other hand, if we talk to QEMU using QMP, we
should just wait for the STOP event and let the event handler update the
state and trigger a libvirt event.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When SPICE graphics is configured for a domain but we did not ask the
client to switch to the destination, we should not wait for
SPICE_MIGRATE_COMPLETED event (which will never come).
https://bugzilla.redhat.com/show_bug.cgi?id=1151723
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Stopping a domain without a job risks a race condition with another
thread which started a job a which does not expect anyone else to be
messing around with the same domain object.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Our existing virHashForEach method iterates through all items disregarding the
fact, that some of the iterators might have actually failed. Errors are usually
dispatched through an error element in opaque data which then causes the
original caller of virHashForEach to return -1. In that case, virHashForEach
could return as soon as one of the iterators fail. This patch changes the
iterator return type and adjusts all of its instances accordingly, so the
actual refactor of virHashForEach method can be dealt with later.
Signed-off-by: Erik Skultety <eskultet@redhat.com>
So, systemd-machined has this philosophy that machine names are like
hostnames and hence should follow the same rules. But we always allowed
international characters in domain names. Thus we need to modify the
machine name we are passing to systemd.
In order to change some machine names that we will be passing to systemd,
we also need to call TerminateMachine at the end of a lifetime of a
domain. Even for domains that were started with older libvirt. That
can be achieved thanks to virSystemdGetMachineNameByPID(). And because
we can change machine names, we can get rid of the inconsistent and
pointless escaping of domain names when creating machine names.
So this patch modifies the naming in the following way. It creates the
name as <drivername>-<id>-<name> where invalid hostname characters are
stripped out of the name and if the resulting name is longer, it
truncates it to 64 characters. That way we can start domains we
couldn't start before. Well, at least on systemd.
To make it work all together, the machineName (which is needed only with
systemd) is saved in domain's private data. That way the generation is
moved to the driver and we don't need to pass various unnecessary
arguments to cgroup functions.
The only thing this complicates a bit is the scope generation when
validating a cgroup where we must check both old and new naming, so a
slight modification was needed there.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1282846
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The virDomainSnapshotDefFormat calls into virDomainDefFormat,
so should be providing a non-NULL virCapsPtr instance. On the
qemu driver we change qemuDomainSnapshotWriteMetadata to also
include caps since it calls virDomainSnapshotDefFormat.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
While this is no functional change, whole channel definition is
going to be needed very soon. Moreover, while touching this obey
const correctness rule in qemuAgentOpen() - so far it was passed
regular pointer to channel config even though the function is
expected to not change pointee at all. Pass const pointer
instead.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The structure actually contains migration statistics rather than just
the status as the name suggests. Renaming it as
qemuMonitorMigrationStats removes the confusion.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add qemuDomainHasVCpuPids to do the checking and replace in place checks
with it.
We no longer need checking whether the thread contains fake data
(vcpupids[0] == vm->pid) as in b07f3d821d
and 65686e5a81 this was removed.
Currently the QEMU monitor is given an FD to the logfile. This
won't work in the future with virtlogd, so it needs to use the
qemuDomainLogContextPtr instead, but it shouldn't directly
access that object either. So define a callback that the
monitor can use for reporting errors from the log file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The qemuDomainTaint APIs currently expect to be passed a log file
descriptor. Change them to instead use a qemuDomainLogContextPtr
to hide the implementation details.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Convert the places which create/open log files to use the new
qemuDomainLogContextPtr object instead.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Introduce a qemuDomainLogContext object to encapsulate
handling of I/O to/from the domain log file. This will
hide details of the log file implementation from the
rest of the driver, making it easier to introduce
support for virtlogd later.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
There are two pretty similar functions qemuProcessReadLog and
qemuProcessReadChildErrors. Both read from the QEMU log file
and try to strip out libvirt messages. The latter then reports
an error, while the former lets the callers report an error.
Re-write qemuProcessReadLog so that it uses a single read
into a dynamically allocated buffer. Then introduce a new
qemuProcessReportLogError that calls qemuProcessReadLog
and reports an error.
Convert all callers to use qemuProcessReportLogError.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
We only started an async job for incoming migration from another host.
When we were starting a domain from scratch or restoring from a saved
state (migration from file) we didn't set any async job. Let's introduce
a new QEMU_ASYNC_JOB_START for these cases.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
If mlock is required either due to use of VFIO hostdevs or due to the
fact that it's enabled it needs to be tweaked prior to adding new memory
or after removing a module. Add a helper to determine when it's
necessary and reuse it both on hotplug and hotunplug.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1273491
Extract the size determination into a separate function and reuse it
across the memory device alignment functions. Since later we will need
to decide the alignment size according to architecture let's pass def to
the functions.
I always felt like this function is qemu specific rather than
libvirt-wide. Other drivers may act differently on virDomainDef
change and in fact may require talking to underlying hypervisor
even if something else's than disk->src has changed. I know that
the function is still incomplete, but lets break that into two
commits that are easier to review. This one is pure code
movement.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This new private API should return true iff sources of two disks
differs in sense that qemu should be instructed to change the
disk backend. For instance, ejecting a CDROM is such case, or
pointing disk into a different ISO location, and so on.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Rather than have different usages of STR function in order to determine
whether the domain is s390-ccw or s390-ccw-virtio, make a single API
which will check the machine.os prefix. Then use the function.
Since we already support the MIGRATION event, we just need to make sure
the domain condition is signalled whenever a p2p connection drops or the
domain is paused due to IO error and we can avoid waking up every 50 ms
to check whether something happened.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Since QEMU commit ea96bc6 [1]:
i386: drop FDC in pc-q35-2.4+ if neither it nor floppy drives are wanted
the floppy controller is no longer implicit.
Specify it explicitly on the command line if the machine type version
is 2.4 or later.
Note that libvirt's floppy drives do not result in QEMU implying the
controller, because libvirt uses if=none instead of if=floppy.
https://bugzilla.redhat.com/show_bug.cgi?id=1227880
[1] http://git.qemu.org/?p=qemu.git;a=commitdiff;h=ea96bc6
QEMU_CAPS_SEAMLESS_MIGRATION capability says QEMU supports
SPICE_MIGRATE_COMPLETED event. Thus we can just drop all code which
polls query-spice and replace it with waiting for the event.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
By switching block jobs to use domain conditions, we can drop some
pretty complicated code in NBD storage migration.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
When qemu does not support the balloon event the current memory size
needs to be queried. Since there are two places that implement the same
logic, split it out into a function and reuse.
Instead of redoing the same filtering over and over everytime we need to
walk through all disks which are being migrated.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add 'thread_id' to the virDomainIOThreadIDDef as a means to store the
'thread_id' as returned from the live qemu monitor data.
Remove the iothreadpids list from _qemuDomainObjPrivate and replace with
the new iothreadids 'thread_id' element.
Rather than use the default numbering scheme of 1..number of iothreads
defined for the domain, use the iothreadid's list for the iothread_id
Since iothreadids list keeps track of the iothread_id's, these are
now used in place of the many places where a for loop would "know"
that the ID was "+ 1" from the array element.
The new tests ensure usage of the <iothreadid> values for an exact number
of iothreads and the usage of a smaller number of <iothreadid> values than
iothreads that exist (and usage of the default numbering scheme).
When the guest agent channel gets hotplugged to a VM, libvirt would
still report that "QEMU guest agent is not configured" rather than
stating that the connection was not established yet.
Currently the code won't be able to connect to the agent after hotplug
but that will change in a later patch.
As the qemuFindAgentConfig() helper is quite helpful in this case move
it to a more usable place and export it.
virDomainGetJobStats is able to report statistics of a completed
migration, however to get usable downtime and total time statistics both
hosts have to keep synchronized time. To provide at least some
estimation of the times even when NTP daemons are not running on both
hosts we can just ignore the time needed to transfer a migration cookie
to the destination host. The result will be also inaccurate but a bit
more predictable. The total/down time will just be at least what we
report.
https://bugzilla.redhat.com/show_bug.cgi?id=1213434
This is basically turning qemuDomObjEndAPI into a more general
function. Other drivers which gets a reference to domain objects may
benefit from this function too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This needs to specified in way too many places for a simple validation
check. The ostype/arch/virttype validation checks later in
DomainDefParseXML should catch most of the cases that this was covering.
Instead of always using controller 0 and incrementing port number,
respect the maximum port numbers of controllers and use all of them.
Ports for virtio consoles are quietly reserved, but not formatted
(neither in XML nor on QEMU command line).
Also rejects duplicate virtio-serial addresses.
https://bugzilla.redhat.com/show_bug.cgi?id=890606https://bugzilla.redhat.com/show_bug.cgi?id=1076708
Test changes:
* virtio-auto.args
Filling out the port when just the controller is specified.
switched from using
maxport + 1
to:
first free port on the controller
* virtio-autoassign.args
Filling out the address when no <address> is specified.
Started using all the controllers instead of 0, also discards
the bus value.
* xml -> xml output of virtio-auto
The port assignment is no longer done as a part of XML parsing,
so the unspecified values stay 0.
This is very helpful when we want to log and report why we could not
acquire a state change lock. Reporting what job keeps it locked helps
with understanding the issue. Moreover, after calling
virDomainGetControlInfo, it's possible to tell whether libvirt is just
stuck somewhere within the API (or it just forgot to cleanup the job) or
whether libvirt is waiting for QEMU to reply.
The error message will look like the following:
# virsh resume cd
error: Failed to resume domain cd
error: Timed out during operation: cannot acquire state change lock
(held by remoteDispatchDomainSuspend)
https://bugzilla.redhat.com/show_bug.cgi?id=853839
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Add support to start qemu instance with 'pc-dimm' device. Thanks to the
refactors we are able to reuse the existing function to determine the
parameters.
When using 'dimm' memory devices with qemu, some of the information
like the slot number and base address need to be reloaded from qemu
after process start so that it reflects the actual state. The state then
allows to use memory devices across migrations.
The memory sizes in qemu are aligned up to 1 MiB boundaries. There are
two places where this was done once for the total size and then for
individual NUMA cell sizes.
Add a function that will align the sizes in one place so that it's clear
where the sizes are aligned.
Surprisingly we did not grab a VM job when a block job finished and we'd
happily rewrite the backing chain data. This made it possible to crash
libvirt when queueing two backing chains tightly and other badness.
To fix it, add yet another handler to the helper thread that handles
monitor events that require a job.
Depending on the context, either error out if the domain
has disappeared in the meantime, or just ignore the value
to allow marking the function as ATTRIBUTE_RETURN_CHECK.
The domain might disappear during the time in monitor when
the virDomainObjPtr is unlocked, so the caller needs to check
if it's still alive.
Since most of the callers are going to need it, put the
check inside qemuDomainObjExitMonitor and return -1 if
the domain died in the meantime.
There is one problem that causes various errors in the daemon. When
domain is waiting for a job, it is unlocked while waiting on the
condition. However, if that domain is for example transient and being
removed in another API (e.g. cancelling incoming migration), it get's
unref'd. If the first call, that was waiting, fails to get the job, it
unref's the domain object, and because it was the last reference, it
causes clearing of the whole domain object. However, when finishing the
call, the domain must be unlocked, but there is no way for the API to
know whether it was cleaned or not (unless there is some ugly temporary
variable, but let's scratch that).
The root cause is that our APIs don't ref the objects they are using and
all use the implicit reference that the object has when it is in the
domain list. That reference can be removed when the API is waiting for
a job. And because each domain doesn't do its ref'ing, it results in
the ugly checking of the return value of virObjectUnref() that we have
everywhere.
This patch changes qemuDomObjFromDomain() to ref the domain (using
virDomainObjListFindByUUIDRef()) and adds qemuDomObjEndAPI() which
should be the only function in which the return value of
virObjectUnref() is checked. This makes all reference counting
deterministic and makes the code a bit clearer.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
When requested in a later patch, the QMP command results are now
examined recursively. As qemu_driver will eventually have to
read items out of the hash table as stored by this patch, the
computation of backing alias string is done in a shared location.
* src/qemu/qemu_domain.h (qemuDomainStorageAlias): New prototype.
* src/qemu/qemu_domain.c (qemuDomainStorageAlias): Implement it.
* src/qemu/qemu_monitor_json.c
(qemuMonitorJSONGetOneBlockStatsInfo)
(qemuMonitorJSONBlockStatsUpdateCapacityOne): Perform recursion.
(qemuMonitorJSONGetAllBlockStatsInfo)
(qemuMonitorJSONBlockStatsUpdateCapacity): Update callers.
Signed-off-by: Eric Blake <eblake@redhat.com>
Move entering the job into the thread to simplify the program flow. Also
as the code holds a separate reference to the domain object some
conditions can be simplified.
After this patch qemuDomainObjTransferJob is no longer needed so this
patch removes it.
https://bugzilla.redhat.com/show_bug.cgi?id=1160084
As of b6d4dad11b (1.2.5) we are trying to keep the status of FSFreeze
in the guest. Even though I've tried to fixed couple of corner cases
(6ea54769ba), it occurred to me just recently, that the approach is
broken by design. Firstly, there are many other ways to talk to
qemu-ga (even through libvirt) that filesystems can be thawed (e.g.
qemu-agent-command) without libvirt noticing. Moreover, there are
plenty of ways to thaw filesystems without even qemu-ga noticing (yes,
qemu-ga keeps internal track of FSFreeze status). So, instead of
keeping the track ourselves, or asking qemu-ga for stale state, it's
the best to let qemu-ga deal with that (and possibly let guest kernel
propagate an error).
Moreover, there's one bug with the following approach, if fsfreeze
command failed, we've executed fsthaw subsequently. So issuing
domfsfreeze in virsh gave the following result:
virsh # domfsfreeze gentoo
Froze 1 filesystem(s)
virsh # domfsfreeze gentoo
error: Unable to freeze filesystems
error: internal error: unable to execute QEMU agent command 'guest-fsfreeze-freeze': The command guest-fsfreeze-freeze has been disabled for this instance
virsh # domfsfreeze gentoo
Froze 1 filesystem(s)
virsh # domfsfreeze gentoo
error: Unable to freeze filesystems
error: internal error: unable to execute QEMU agent command 'guest-fsfreeze-freeze': The command guest-fsfreeze-freeze has been disabled for this instance
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
New qemu added a new event that is emitted when a virtio serial channel
is opened in the guest OS. This allows us to update the state of the
port in the output-only XML element.
This patch implements the monitor callbacks and necessary handlers to
update the state in the definition.
NIC_RX_FILTER_CHANGED is sent by qemu any time a NIC driver in the
guest modified the NIC's RX Filter (for example, if the MAC address of
the NIC is changed by the guest).
This patch doesn't do anything useful with that event; it just sets up
all the plumbing to get news of the event into a worker thread with
all proper locking/reference counting, and provide an easy place to
add in desired functionality.
See src/qemu/EVENTHANDLERS.txt for information/instructions on adding
a libvirt-internal handler for a qemu event (using
NIC_RX_FILTER_CHANGED as an example).
Request erroring out from the backing chain traveller and drop qemu's
internal backing chain integrity tester.
The backing chain traveller reports errors by itself with possibly more
detail than qemuDiskChainCheckBroken ever could.
We also need to make sure that we reconnect to existing qemu instances
even at the cost of losing the backing chain info (this really should be
stored in the XML rather than reloaded from disk, but that needs some
work).
Total time of a migration and total downtime transfered from a source to
a destination host do not count with the transfer time to the
destination host and with the time elapsed before guest CPUs are
resumed. Thus, source libvirtd remembers when migration started and when
guest CPUs were paused. Both timestamps are transferred to destination
libvirtd which uses them to compute total migration time and total
downtime. Obviously, this requires the time to be synchronized between
the two hosts. The reported times are useless otherwise but they would
be equally useless if we didn't do this recomputation so don't lose
anything by doing it.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
virDomainGetJobStats gains new VIR_DOMAIN_JOB_STATS_COMPLETED flag that
can be used to fetch statistics of a completed job rather than a
currently running job.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Job statistics data were tracked in several structures and variables.
Let's make a new qemuDomainJobInfo structure which can be used as a
single source of statistics data as a preparation for storing data about
completed a job.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
During a QEMU live migration several warning messages about job
handling could be written to syslog on the destination host:
"entering monitor without asking for a nested job is dangerous"
The messages are written because the job handling during migration
uses hard coded asyncJob values in several places that are incorrect.
This patch passes the required asyncJob value around and prevents
the warnings as well as any issues that the warnings may be referring
to.
https://bugzilla.redhat.com/show_bug.cgi?id=1130089
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
As we are doing with the enum structures, a cleanup in "src/qemu/"
directory was done now. All the enums that were defined in the
header files were converted to typedefs in this directory. This
patch includes all the adjustments to remove conflicts when you do
this kind of change. "Enum-to-typedef"'s conversions were made in
"src/qemu/qemu_{capabilities, domain, migration, hotplug}.h".
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
In "src/conf/domain_conf.h" there are many enum declarations. The
cleanup in this header filer was started, but it wasn't enough and
there are many other files that has enum variables declared. So, the
commit was starting to be big. This commit finish the cleanup in this
header file and in other files that has enum variables, parameters,
or functions declared.
Signed-off-by: Julio Faracco <jcfaracco@gmail.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Currently, we don not acquire any job when removing a device after
DEVICE_DELETED event was received from QEMU. This means that if there is
another API running at the time DEVICE_DELETED is delivered and the API
acquired a job, we may happily change the definition of the domain the
API is working with whenever it unlocks the domain object (e.g., to talk
with its monitor). That said, we have to acquire a job before finishing
device removal to make things safe. However, doing so in the main event
loop would cause a deadlock so we need to move most of the event handler
into a separate thread.
Another good reason for both acquiring a job and handling the event in a
separate thread is that we currently remove a device backend immediately
after removing its frontend while we should only remove the backend once
we already received DEVICE_DELETED event. That is, we will have to talk
to QEMU monitor from the event handler.
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Introduce new files (domain_addr.[ch]) to provide
an API for domain device handling that could be
shared across the drivers.
A list of data types were extracted and moved there:
qemuDomainPCIAddressBus -> virDomainPCIAddressBus
qemuDomainPCIAddressBusPtr -> virDomainPCIAddressBusPtr
_qemuDomainPCIAddressSet -> virDomainPCIAddressSet
qemuDomainPCIAddressSetPtr -> virDomainPCIAddressSetPtr
qemuDomainPCIConnectFlags -> virDomainPCIConnectFlags
Also, move the related definitions and macros.
Adds 'quiesced' status into qemuDomainObjPrivate that tracks whether
FSFreeze is requested in the domain.
It modifies error code from qemuDomainSnapshotFSFreeze and
qemuDomainSnapshotFSThaw, so that a caller can know whether the command is
actually sent to the guest agent. If the error is caused before sending a
freeze command, a counterpart thaw command shouldn't be sent either, not to
confuse fsfreeze status tracking.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
Currently, there's just one place where we care if hook script is
changing the domain XML: migration hook for incoming migration. In
all other places where a hook script is executed, we don't read the
XML back from the script.
Anyway, the hook script can alter domain XML and hence we should taint
it if the script did.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
The code took into account only the global permissions. The domains now
support per-vm DAC labels and per-image DAC labels. Use the most
specific label available.
Couple of codepaths shared the same code which can be moved out to a
function and on one of such places, qemuMigrationConfirmPhase(), the
domain was resumed even if it wasn't running before the migration
started.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1057407
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1019053
When we migrate vms concurrently, there's a chance that libvirtd on
destination assigns the same port for different migrations, which will
lead to migration failure during prepare phase on destination. So we use
virPortAllocator here to solve the problem.
Signed-off-by: Wang Yufei <james.wangyufei@huawei.com>
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=994364
Whenever we check for ABI stability, we have new xml (e.g. provided by
user, or obtained from snapshot, whatever) which we compare to old xml
and see if ABI won't break. However, if the new xml was produced via
virDomainGetXMLDesc(..., VIR_DOMAIN_XML_MIGRATABLE) it lacks some
devices, e.g. 'pci-root' controller. Hence, the ABI stability check
fails even though it is stable. Moreover, we can't simply fix
virDomainDefCheckABIStability because removing the correct devices is
task for the driver. For instance, qemu driver wants to remove the usb
controller too, while LXC driver doesn't. That's why we need special
qemu wrapper over virDomainDefCheckABIStability which removes the
correct devices from domain XML, produces MIGRATABLE xml and calls the
check ABI stability function.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This function is to guess the correct limit for maximal memory
usage by qemu for given domain. This can never be guessed
correctly, not to mention all the pains and sleepless nights this
code has caused. Once somebody discovers algorithm to solve the
Halting Problem, we can compute the limit algorithmically. But
till then, this code should never see the light of the release
again.
*src/util/virstoragefile.c: Add a helper function to get
the first name of missing backing files, if the name is NULL,
it means the diskchain is not broken.
*src/qemu/qemu_domain.c: qemuDiskChainCheckBroken(disk) to
check if its chain is broken
In case libvirtd is asked to unplug a device but the device is actually
unplugged later when libvirtd is not running, we need to detect that and
remove such device when libvirtd starts again and reconnects to running
domains.
Add monitor callback API domainGuestPanic, that implements
'destroy', 'restart' and 'preserve' events of the 'on_crash'
in the XML when domain crashed.
Convert input XML to migratable before using it in
qemuDomainSaveImageOpen.
XML in the save image is migratable, i.e. doesn't contain implicit
controllers. If these controllers were in a non-default order in the
input XML, the ABI check would fail. Removing and re-adding these
controllers fixes it.
https://bugzilla.redhat.com/show_bug.cgi?id=834196
POSIX says pthread_t is opaque. We can't guarantee if it is scaler
or a pointer, nor what size it is; and BSD differs from Linux.
We've also had reports of gcc complaining on attempts to cast it,
if we use a cast to the wrong type (for example, pointers have to be
cast to void* or intptr_t before being narrowed; while casting a
function return of scalar pthread_t to void* triggers a different
warning).
Give up on casts, and use unions to get at decent bits instead. And
rather than futz around with figuring which 32 bits of a potentially
64-bit pointer are most likely to be unique, convert the rest of
the code base to use 64-bit values when using a debug id.
Based on a report by Guido Günther against kFreeBSD, but with a
fix that doesn't regress commit 4d970fd29 for FreeBSD.
* src/util/virthreadpthread.c (virThreadSelfID, virThreadID): Use
union to get at a decent bit representation of thread_t bits.
* src/util/virthread.h (virThreadSelfID, virThreadID): Alter
signature.
* src/util/virthreadwin32.c (virThreadSelfID, virThreadID):
Likewise.
* src/qemu/qemu_domain.h (qemuDomainJobObj): Alter type of owner.
* src/qemu/qemu_domain.c (qemuDomainObjTransferJob)
(qemuDomainObjSetJobPhase, qemuDomainObjReleaseAsyncJob)
(qemuDomainObjBeginNestedJob, qemuDomainObjBeginJobInternal): Fix
clients.
* src/util/virlog.c (virLogFormatString): Likewise.
* src/util/vireventpoll.c (virEventPollInterruptLocked):
Likewise.
Signed-off-by: Eric Blake <eblake@redhat.com>
Instead of calling virCgroupForDomain every time we need
the virCgrouPtr instance, just do it once at Vm startup
and cache a reference to the object in qemuDomainObjPrivatePtr
until shutdown of the VM. Removing the virCgroupPtr from
the QEMU driver state also means we don't have stale mount
info, if someone mounts the cgroups filesystem after libvirtd
has been started
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This patch implements the devices post parse callback and uses it to fill
the default qemu network card model into the XML if none is specified.
Libvirt assumes that the network card model for qemu is the "rtl8139".
Record this in the XML using the new callback to avoid user
confusion.
This commit adds the QEMU driver support for CCW addresses. The
current QEMU only allows virtio devices to be attached to the
CCW bus. We named the new capability indicating that support
QEMU_CAPS_VIRTIO_CCW accordingly.
The fact that CCW devices can only be assigned to domains with a
machine type of s390-ccw-virtio requires a few extra checks for
machine type in qemu_command.c on top of querying
QEMU_CAPS_VIRTIO_{CCW|S390}.
The majority of the new functions deals with CCW address generation
and management.
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
The virCaps structure gathered a ton of irrelevant data over time that.
The original reason is that it was propagated to the XML parser
functions.
This patch aims to create a new data structure virDomainXMLConf that
will contain immutable data that are used by the XML parser. This will
allow two things we need:
1) Get rid of the stuff from virCaps
2) Allow us to add callbacks to check and add driver specific stuff
after domain XML is parsed.
This first attempt removes pointers to private data allocation functions
to this new structure and update all callers and function that require
them.
This reverts the hack done in
commit 568a6cda27
Author: Jiri Denemark <jdenemar@redhat.com>
Date: Fri Feb 15 15:11:47 2013 +0100
qemu: Avoid deadlock in autodestroy
since we now have a fix which avoids the deadlock scenario
entirely
qemuProcessStart expects to be run with a job already set and every
caller except for qemuMigrationPrepareAny use it correctly. This bug can
be observed in libvirtd logs during incoming migration as
warning : qemuDomainObjEnterMonitorInternal:979 : This thread seems
to be the async job owner; entering monitor without asking for a
nested job is dangerous
This migration cookie is meant for two purposes. The first is to be sent
in begin phase from source to destination to let it know we support new
implementation of VIR_MIGRATE_NON_SHARED_{DISK,INC} so destination can
start NBD server. Then, the second purpose is, destination can let us
know, on which port the NBD server is running.
As a side effect, this also fixes reporting disk migration process.
It was added to memory migration progress, which was wrong. Disk
progress has dedicated fields in virDomainJobInfo structure.
With the majority of fields in the virQEMUDriverPtr struct
now immutable or self-locking, there is no need for practically
any methods to be using the QEMU driver lock. Only a handful
of helper APIs in qemu_conf.c now need it
To avoid confusion between 'virCapsPtr' and 'qemuCapsPtr'
do some renaming of various fucntions/variables. All
instances of 'qemuCapsPtr' are renamed to 'qemuCaps'. To
avoid that clashing with the 'qemuCaps' typedef though,
rename the latter to virQEMUCaps.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The functionality provided in virchrdev.c (previously virconsole.c) is
applicable to other types of character devices besides consoles, such
as channels. This patch is just code motion, renaming things such as
"console" or "pty", instead using more general terms such as
"character device" or "device path".
Replace the following names
* struct qemu_snap_remove with virQEMUSnapRemovePtr
* struct qemu_snap_reparent with virQEMUSnapReparentPtr
* struct qemu_save_header with virQEMUSaveHeaderPtr
* enum qemu_save_formats with virQEMUSaveFormat
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Remove the obsolete 'qemud' naming prefix and underscore
based type name. Introduce virQEMUDriverPtr as the replacement,
in common with LXC driver naming style
Currently, if user calls virDomainAbortJob we just issue
'migrate_cancel' and hope for the best. However, if user calls
the API in wrong phase when migration hasn't been started yet
(perform phase) the cancel request is just ignored. With this
patch, the request is remembered and as soon as perform phase
starts, migration is cancelled.
The new external system checkpoints will require an async job while the
snapshot is taken. This patch adds QEMU_ASYNC_JOB_SNAPSHOT to track this
job type.
Technically, we should not be re-probing any file that qemu might
be currently writing to. As such, we should cache the backing
file chain prior to starting qemu. This patch adds the cache,
but does not use it until the next patch.
Ultimately, we want to also store the chain in domain XML, so that
it is remembered across libvirtd restarts, and so that the only
kosher way to modify the backing chain of an offline domain will be
through libvirt API calls, but we aren't there yet. So for now, we
merely invalidate the cache any time we do a live operation that
alters the chain (block-pull, block-commit, external disk snapshot),
as well as tear down the cache when the domain is not running.
* src/conf/domain_conf.h (_virDomainDiskDef): New field.
* src/conf/domain_conf.c (virDomainDiskDefFree): Clean new field.
* src/qemu/qemu_domain.h (qemuDomainDetermineDiskChain): New
prototype.
* src/qemu/qemu_domain.c (qemuDomainDetermineDiskChain): New
function.
* src/qemu/qemu_driver.c (qemuDomainAttachDeviceDiskLive)
(qemuDomainChangeDiskMediaLive): Pre-populate chain.
(qemuDomainSnapshotCreateSingleDiskActive): Uncache chain before
snapshot.
* src/qemu/qemu_process.c (qemuProcessHandleBlockJob): Update
chain after block pull.
Using VIR_DOMAIN_XML_MIGRATABLE flag, one can request domain's XML
configuration that is suitable for migration or save/restore. Such XML
may contain extra run-time stuff internal to libvirt and some default
configuration may be removed for better compatibility of the XML with
older libvirt releases.
This flag may serve as an easy way to get the XML that can be passed
(after desired modifications) to APIs that accept custom XMLs, such as
virDomainMigrate{,ToURI}2 or virDomainSaveFlags.
https://www.gnu.org/licenses/gpl-howto.html recommends that
the 'If not, see <url>.' phrase be a separate sentence.
* tests/securityselinuxhelper.c: Remove doubled line.
* tests/securityselinuxtest.c: Likewise.
* globally: s/; If/. If/
The current qemu capabilities are stored in a virBitmapPtr
object, whose type is exposed to callers. We want to store
more data besides just the flags, so we need to move to a
struct type. This object will also need to be reference
counted, since we'll be maintaining a cache of data per
binary. This change introduces a 'qemuCapsPtr' virObject
class. Most of the change is just renaming types and
variables in all the callers
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This has several benefits:
1. Future snapshot-related code has a definite place to go (and I
_will_ be adding some)
2. Snapshot errors now use the VIR_FROM_DOMAIN_SNAPSHOT error
classification, which has been underutilized (previously only in
libvirt.c)
* src/conf/domain_conf.h, domain_conf.c: Split...
* src/conf/snapshot_conf.h, snapshot_conf.c: ...into new files.
* src/Makefile.am (DOMAIN_CONF_SOURCES): Build new files.
* po/POTFILES.in: Mark new file for translation.
* src/vbox/vbox_tmpl.c: Update caller.
* src/esx/esx_driver.c: Likewise.
* src/qemu/qemu_command.c: Likewise.
* src/qemu/qemu_domain.h: Likewise.
Previously, qemu did not respond to monitor commands during migration if
the limit was too high. This prevented us from raising the limit
earlier. The qemu issue seems to be fixed (according to my testing) and
we may remove the 32Mb/s limit.
Switch virDomainObjPtr to use the virObject APIs for reference
counting. The main change is that virObjectUnref does not return
the reference count, merely a bool indicating whether the object
still has any refs left. Checking the return value is also not
mandatory.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Per the FSF address could be changed from time to time, and GNU
recommends the following now: (http://www.gnu.org/licenses/gpl-howto.html)
You should have received a copy of the GNU General Public License
along with Foobar. If not, see <http://www.gnu.org/licenses/>.
This patch removes the explicit FSF address, and uses above instead
(of course, with inserting 'Lesser' before 'General').
Except a bunch of files for security driver, all others are changed
automatically, the copyright for securify files are not complete,
that's why to do it manually:
src/security/security_selinux.h
src/security/security_driver.h
src/security/security_selinux.c
src/security/security_apparmor.h
src/security/security_apparmor.c
src/security/security_driver.c
When we added the default USB controller into domain XML, we efficiently
broke migration to older versions of libvirt that didn't support USB
controllers at all (0.9.4 and earlier) even for domains that don't use
anything that the older libvirt can't provide. We still want to present
the default USB controller in any XML seen by a user/app but we can
safely remove it from the domain XML used during migration. If we are
migrating to a new enough libvirt, it will add the controller XML back,
while older libvirt won't be confused with it although it will still
tell qemu to create the controller.
Similar approach can be used in the future whenever we find out we
always enabled some kind of device without properly advertising it in
domain XML.
In case an API fails with "cannot acquire state change lock", searching
for the API that possibly forgot to end its job is not always easy.
Let's keep track of the job owner and print it out for easier
identification.
As reported by Daniel Berrangé, we have a huge performance regression
for virDomainGetInfo() due to the change which makes virDomainEndJob()
save the XML status file every time it is called. Previous to that
change, 2000 calls to virDomainGetInfo() took ~2.5 seconds. After that
change, 2000 calls to virDomainGetInfo() take 2 *minutes* 45 secs.
We made the change to be able to recover from libvirtd restart in the
middle of a job. However, only destroy and async jobs are taken care of.
Thus it makes more sense to only save domain state XML when these jobs
are started/stopped.
Destination daemon should not rely on the client or source daemon
(depending on the type of migration) to call Finish when migration
fails, because the client may crash before it can do so. The domain
prepared for incoming migration is set to be destroyed (and migration
job cleaned up) when connection with the client closes but this is not
enough. If the associated qemu process crashes after Prepare step and
the domain is cleaned up before the connection gets closed, autodestroy
is not called for the domain and migration jobs remains set. In case the
domain is defined on destination host (i.e., it is not completely
removed once destroyed) we keep the job set for ever. To fix this, we
register a cleanup callback which is responsible to clean migration-in
job when a domain dies anywhere between Prepare and Finish steps. Note
that we can't blindly clean any job when spotting EOF on monitor since
normally an API is running at that time.
This reverts commit 61f2b6ba5f and most of
commit d8916dc8e2, which effectively
brings back commit ef1065cf5a written by
Jim Fehlig:
The qemu migration speed default is 32MiB/s as defined in migration.c
/* Migration speed throttling */
static int64_t max_throttle = (32 << 20);
There's no need to throttle migration when targeting a file, so set
migration speed to unlimited prior to migration, and restore to libvirt
default value after migration.
Default units is MB for migrate_set_speed monitor command, so
(INT64_MAX / (1024 * 1024)) is used for unlimited migration speed.
This was reverted because migration to file could not be canceled and
even monitored since qemu was not processing any monitor commands until
the migration finished. This is now different as we make sure the
file descriptor we pass to qemu is able to properly report EAGAIN.
Recent qemu changes might have helped as well.
I tested managedsave with this patch in and indeed, it is 10x faster
while I can still monitor its progress.
When host-model and host-passthrouh CPU modes were introduced, qemu
driver was properly modify to update guest CPU definition during
migration so that we use the right CPU at the destination. However,
similar treatment is needed for (managed)save and snapshots since they
need to save the exact CPU so that a domain can be properly restored.
To avoid repetition of such situation, all places that need live XML
share the code which generates it.
As a side effect, this patch fixes error reporting from
qemuDomainSnapshotWriteMetadata().
This patch fixes console corruption, that happens if two concurrent
sessions are opened for a single console on a domain. Result of this
corruption was that each of the console streams recieved just a part
of the data written to the pipe so every console rendered unusable.
New helper function for safe console handling is used to establish the
console stream connection. This function ensures that no other libvirt
client is using the console (with the ability to disconnect consoles of
libvirt clients) and that no UUCP style lockfile is placed on the PTY
device.
* src/qemu/qemu_domain.h
- add data structure to domain's private data dealing with
console connections
* src/qemu/qemu_domain.c:
- allocate/free domain's console data structure
* src/qemu/qemu_driver.c
- use the new helper function for console handling
There is now a standard QEMU guest agent that can be installed
and given a virtio serial channel
<channel type='unix'>
<source mode='bind' path='/var/lib/libvirt/qemu/f16x86_64.agent'/>
<target type='virtio' name='org.qemu.guest_agent.0'/>
</channel>
The protocol that runs over the guest agent is JSON based and
very similar to the JSON monitor. We can't use exactly the same
code because there are some odd differences in the way messages
and errors are structured. The qemu_agent.c file is based on
a combination and simplification of qemu_monitor.c and
qemu_monitor_json.c
* src/qemu/qemu_agent.c, src/qemu/qemu_agent.h: Support for
talking to the agent for shutdown
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add thread
helpers for talking to the agent
* src/qemu/qemu_process.c: Connect to agent whenever starting
a guest
* src/qemu/qemu_monitor_json.c: Make variable static
In commit 6f84e110 I mistakenly set default migration speed to
33554432 Mb! The units of migMaxBandwidth is Mb, with conversion
handled in qemuMonitor{JSON,Text}SetMigrationSpeed().
Also, remove definition of QEMU_DOMAIN_FILE_MIG_BANDWIDTH_MAX since
it is no longer used after reverting commit ef1065cf.
When destroying a domain qemuDomainDestroy kills its qemu process and
starts a new job, which means it unlocks the domain object and locks it
again after some time. Although the object is usually unlocked for a
pretty short time, chances are another thread processing an EOF event on
qemu monitor is able to lock the object first and does all the cleanup
by itself. This leads to wrong shutoff reason and lifecycle event detail
and virDomainDestroy API incorrectly reporting failure to destroy an
inactive domain.
Reported by Charlie Smurthwaite.
This patch implements on_missing feature in qemu driver.
Upon qemu startup process an accessibility of CDROMs
and floppy disks is checked. The source might get dropped
if unavailable and on_missing is set accordingly.
No event is emit thought. Look for follow up patch.
Destination libvirtd remembers the original name in the prepare phase
and clears it in the finish phase. The original name is used when
comparing domain name in migration cookie.
Currently, qemuDomainGetXMLDesc and qemudDomainGetInfo check for
outstanding synchronous job before (eventual) monitor entering.
However, there can be already async job set, e.g. migration.
This patch is mostly code motion - moving some functions out
of qemu_driver and into qemu_domain so they can be reused by
multiple qemu_* files (since qemu_driver.h must not grow).
It also adds a new helper function, qemuDomainRemoveInactive,
which will be used in the next patch.
* src/qemu/qemu_domain.h (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll)
(qemuDomainRemoveInactive): New prototypes.
(struct qemu_snap_remove): New struct.
* src/qemu/qemu_domain.c (qemuDomainRemoveInactive)
(qemuDomainSnapshotDiscardAllMetadata): New functions.
(qemuFindQemuImgBinary, qemuDomainSnapshotWriteMetadata)
(qemuDomainSnapshotForEachQcow2, qemuDomainSnapshotDiscard)
(qemuDomainSnapshotDiscardAll): Move here...
* src/qemu/qemu_driver.c (qemuFindQemuImgBinary)
(qemuDomainSnapshotWriteMetadata, qemuDomainSnapshotForEachQcow2)
(qemuDomainSnapshotDiscard, qemuDomainSnapshotDiscardAll): ...from
here.
(qemuDomainUndefineFlags): Update caller.
* src/conf/domain_conf.c (virDomainRemoveInactive): Doc fixes.
gcc warns when building libvirt 0.9.5 on a 32-bit machine:
qemu/qemu_migration.c: In function 'qemuMigrationToFile':
qemu/qemu_migration.c:2727:38: error: large integer implicitly truncated to unsigned type [-Woverflow]
* src/qemu/qemu_domain.h (QEMU_DOMAIN_FILE_MIG_BANDWIDTH_MAX): Cap
to long when building for 32-bit platform.
The maximum bandwidth that can be consumed when migrating a domain
is better classified as an operational vs configuration parameter of
the dommain. As such, store this parameter in qemuDomainObjPrivate
structure.
This patch creates an optional BeginJob queue size limit. When
active, all other attempts above level will fail. To set this
feature assign desired value to max_queued variable in qemu.conf.
Setting it to 0 turns it off.
Currently, we attempt to run sync job and async job at the same time. It
means that the monitor commands for two jobs can be run in any order.
In the function qemuDomainObjEnterMonitorInternal():
if (priv->job.active == QEMU_JOB_NONE && priv->job.asyncJob) {
if (qemuDomainObjBeginNestedJob(driver, obj) < 0)
We check whether the caller is an async job by priv->job.active and
priv->job.asynJob. But when an async job is running, and a sync job is
also running at the time of the check, then priv->job.active is not
QEMU_JOB_NONE. So we cannot check whether the caller is an async job
in the function qemuDomainObjEnterMonitorInternal(), and must instead
put the burden on the caller to tell us when an async command wants
to do a nested job.
Once the burden is on the caller, then only async monitor enters need
to worry about whether the VM is still running; for sync monitor enter,
the internal return is always 0, so lots of ignore_value can be dropped.
* src/qemu/THREADS.txt: Reflect new rules.
* src/qemu/qemu_domain.h (qemuDomainObjEnterMonitorAsync): New
prototype.
* src/qemu/qemu_process.h (qemuProcessStartCPUs)
(qemuProcessStopCPUs): Add parameter.
* src/qemu/qemu_migration.h (qemuMigrationToFile): Likewise.
(qemuMigrationWaitForCompletion): Make static.
* src/qemu/qemu_domain.c (qemuDomainObjEnterMonitorInternal): Add
parameter.
(qemuDomainObjEnterMonitorAsync): New function.
(qemuDomainObjEnterMonitor, qemuDomainObjEnterMonitorWithDriver):
Update callers.
* src/qemu/qemu_driver.c (qemuDomainSaveInternal)
(qemudDomainCoreDump, doCoreDump, processWatchdogEvent)
(qemudDomainSuspend, qemudDomainResume, qemuDomainSaveImageStartVM)
(qemuDomainSnapshotCreateActive, qemuDomainRevertToSnapshot):
Likewise.
* src/qemu/qemu_process.c (qemuProcessStopCPUs)
(qemuProcessFakeReboot, qemuProcessRecoverMigration)
(qemuProcessRecoverJob, qemuProcessStart): Likewise.
* src/qemu/qemu_migration.c (qemuMigrationToFile)
(qemuMigrationWaitForCompletion, qemuMigrationUpdateJobStatus)
(qemuMigrationJobStart, qemuDomainMigrateGraphicsRelocate)
(doNativeMigrate, doTunnelMigrate, qemuMigrationPerformJob)
(qemuMigrationPerformPhase, qemuMigrationFinish)
(qemuMigrationConfirm): Likewise.
* src/qemu/qemu_hotplug.c: Drop unneeded ignore_value.
qemuMigrationUpdateJobStatus (called in a loop by migration
and save tasks) uses qemuDomainObjEnterMonitorWithDriver;
however, that function ended up starting a nested job without
releasing the driver.
Since no one else is making nested calls, we can inline the
internal functions to properly track driver_locked.
* src/qemu/qemu_domain.h (qemuDomainObjBeginNestedJob)
(qemuDomainObjBeginNestedJobWithDriver)
(qemuDomainObjEndNestedJob): Drop unused prototypes.
* src/qemu/qemu_domain.c (qemuDomainObjEnterMonitorInternal):
Reflect driver lock to nested job.
(qemuDomainObjBeginNestedJob)
(qemuDomainObjBeginNestedJobWithDriver)
(qemuDomainObjEndNestedJob): Drop unused functions.
The compiler might optimize based on our declaration that something
is unused. Putting that declaration in the header risks getting
out of sync with the actual implementation, so it belongs better
only in the .c files. We were mostly compliant, and a new syntax
check will help us in the future.
* cfg.mk (sc_avoid_attribute_unused_in_header): New syntax check.
* src/nodeinfo.h (nodeGetCPUStats, nodeGetMemoryStats): Delete
attribute already present in .c file.
* src/qemu/qemu_domain.h (qemuDomainEventFlush): Likewise.
* src/util/virterror_internal.h (virReportErrorHelper): Parameters
are actually used by .c file.
* src/xenxs/xen_sxpr.h (xenFormatSxprDisk): Adjust prototype.
* src/xenxs/xen_sxpr.c (xenFormatSxprDisk): Delete unused argument.
(xenFormatSxpr): Adjust caller.
* src/xen/xend_internal.c (xenDaemonAttachDeviceFlags)
(xenDaemonUpdateDeviceFlags): Likewise.
Suggested by Daniel Veillard.
Asynchronous jobs may take long time to finish and may consist of
several phases which we need to now about to help with recovery/rollback
after libvirtd restarts.
Query commands are safe to be called during long running jobs (such as
migration). This patch makes them all work without the need to
special-case every single one of them.
The patch introduces new job.asyncCond condition and associated
job.asyncJob which are dedicated to asynchronous (from qemu monitor
point of view) jobs that can take arbitrarily long time to finish while
qemu monitor is still usable for other commands.
The existing job.active (and job.cond condition) is used all other
synchronous jobs (including the commands run during async job).
Locking schema is changed to use these two conditions. While asyncJob is
active, only allowed set of synchronous jobs is allowed (the set can be
different according to a particular asyncJob) so any method that
communicates to qemu monitor needs to check if it is allowed to be
executed during current asyncJob (if any). Once the check passes, the
method needs to normally acquire job.cond to ensure no other command is
running. Since domain object lock is released during that time, asyncJob
could have been started in the meantime so the method needs to recheck
the first condition. Then, normal jobs set job.active and asynchronous
jobs set job.asyncJob and optionally change the list of allowed job
groups.
Since asynchronous jobs only set job.asyncJob, other allowed commands
can still be run when domain object is unlocked (when communicating to
remote libvirtd or sleeping). To protect its own internal synchronous
commands, the asynchronous job needs to start a special nested job
before entering qemu monitor. The nested job doesn't check asyncJob, it
only acquires job.cond and sets job.active to block other jobs.
Avoid re-formatting the pidfile path everytime we need it. Create
it once when starting the guest, and preserve it until the guest
is shutdown.
* src/libvirt_private.syms, src/util/util.c,
src/util/util.h: Add virFileReadPidPath
* src/qemu/qemu_domain.h: Add pidfile field
* src/qemu/qemu_process.c: Store pidfile path in qemuDomainObjPrivate
The drivers were accepting domain configs without checking if those
were actually meant for them. For example the LXC driver happily
accepts configs with type QEMU.
Add a check for the expected domain types to the virDomainDefParse*
functions.
For controlled shutdown we issue a 'system_powerdown' command
to the QEMU monitor. This triggers an ACPI event which (most)
guest OS wire up to a controlled shutdown. There is no equiv
ACPI event to trigger a controlled reboot. This patch attempts
to fake a reboot.
- In qemuDomainObjPrivatePtr we have a bool fakeReboot
flag.
- The virDomainReboot method sets this flag and then
triggers a normal 'system_powerdown'.
- The QEMU process is started with '-no-shutdown'
so that the guest CPUs pause when it powers off the
guest
- When we receive the 'POWEROFF' event from QEMU JSON
monitor if fakeReboot is not set we invoke the
qemuProcessKill command and shutdown continues
normally
- If fakeReboot was set, we spawn a background thread
which issues 'system_reset' to perform a warm reboot
of the guest hardware. Then it issues 'cont' to
start the CPUs again
* src/qemu/qemu_command.c: Add -no-shutdown flag if
we have JSON support
* src/qemu/qemu_domain.h: Add 'fakeReboot' flag to
qemuDomainObjPrivate struct
* src/qemu/qemu_driver.c: Fake reboot using the
system_powerdown command if JSON support is available
* src/qemu/qemu_monitor.c, src/qemu/qemu_monitor.h,
src/qemu/qemu_monitor_json.c, src/qemu/qemu_monitor_json.h,
src/qemu/qemu_monitor_text.c, src/qemu/qemu_monitor_text.h: Add
binding for system_reset command
* src/qemu/qemu_process.c: Reset the guest & start CPUs if
fakeReboot is set
The QEMU integrates with the lock manager instructure in a number
of key places
* During startup, a lock is acquired in between the fork & exec
* During startup, the libvirtd process acquires a lock before
setting file labelling
* During shutdown, the libvirtd process acquires a lock
before restoring file labelling
* During hotplug, unplug & media change the libvirtd process
holds a lock while setting/restoring labels
The main content lock is only ever held by the QEMU child process,
or libvirtd during VM shutdown. The rest of the operations only
require libvirtd to hold the metadata locks, relying on the active
QEMU still holding the content lock.
* src/qemu/qemu_conf.c, src/qemu/qemu_conf.h,
src/qemu/libvirtd_qemu.aug, src/qemu/test_libvirtd_qemu.aug:
Add config parameter for configuring lock managers
* src/qemu/qemu_driver.c: Add calls to the lock manager
Update the qemuDomainMigrateBegin method so that it accepts
an optional incoming XML document. This will be validated
for ABI compatibility against the current domain config,
and if this check passes, will be passed back out for use
by the qemuDomainMigratePrepare method on the target
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h,
src/qemu/qemu_migration.c: Allow custom XML to be passed
Originally most of libvirt domain-specific calls were blocking
during a migration.
A new mechanism to allow specific calls (blkstat/blkinfo) to be
executed in such condition has been implemented.
In the long term it'd be desirable to get a more general
solution to mark further APIs as migration safe, without needing
special case code.
* src/qemu/qemu_migration.c: add some additional job signal
flags for doing blkstat/blkinfo during a migration
* src/qemu/qemu_domain.c: add a condition variable that can be
used to efficiently wait for the migration code to clear the
signal flag
* src/qemu/qemu_driver.c: execute blkstat/blkinfo using the
job signal flags during migration
As well as taint warnings going to the main libvirt log,
add taint warnings to the per-domain logfile
Domain id=3 is tainted: high-privileges
Domain id=3 is tainted: disk-probing
Domain id=3 is tainted: shell-scripts
Domain id=3 is tainted: custom-monitor
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Enhance
qemuDomainTaint to also log to the domain logfile
* src/qemu/qemu_driver.c: Pass -1 for logFD to taint methods to
auto-append to logfile
* src/qemu/qemu_process.c: Pass open logFD at startup for taint
methods
The qemuDomainAppendLog method allows writing a formatted string
to the end of the domain logfile, optionally opening it if needed.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainAppendLog
Move the qemuProcessLogReadFD and qemuProcessLogFD methods
into qemu_domain.c, renaming them to qemuDomainCreateLog
and qemuDomainOpenLog.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainCreateLog and qemuDomainOpenLog.
* src/qemu/qemu_process.c: Remove qemuProcessLogFD
and qemuProcessLogReadFD
Wire up logging of VM tainting to the QEMU driver
- If running QEMU as root user/group or without capabilities
being cleared
- If passing custom QEMU command line args
- If issuing custom QEMU monitor commands
- If using a network interface config with an associated
shell script
- If using a disk config relying on format probing
The warnings, per-VM appear in the main libvirtd logs
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: high-privileges
11:56:17.571: 10832: warning : qemuDomainObjTaint:712 : Domain id=1 name='l2' uuid=c7a3edbd-edaf-9455-926a-d65c16db1802 is tainted: disk-probing
The taint flags are reset when the VM is stopped.
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Helper APIs
for logging taint warnings
* src/qemu/qemu_driver.c: Log tainting with custom QEMU monitor
commands and disk/net hotplug with unsupported configs
* src/qemu/qemu_process.c: Log tainting at startup based on
unsupported configs
To cope with the QEMU binary being changed while a VM is running,
it is neccessary to persist the original qemu capabilities at the
time the VM is booted.
* src/qemu/qemu_capabilities.c, src/qemu/qemu_capabilities.h: Add
an enum for a string rep of every capability
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Support for
storing capabilities in the domain status XML
* src/qemu/qemu_process.c: Populate & free QEMU capabilities at
domain startup
Enhance the QEMU migration monitoring loop, so that it can get
a signal to change migration speed on the fly
* src/qemu/qemu_domain.h: Add signal for changing speed on the fly
* src/qemu/qemu_driver.c: Wire up virDomainMigrateSetSpeed driver
* src/qemu/qemu_migration.c: Support signal for changing speed
The introduction of the v3 migration protocol, along with
support for migration cookies, will significantly expand
the size of the migration code. Move it all to a separate
file to make it more manageable
The functions are not moved 100%. The API entry points
remain in the main QEMU driver, but once the public
virDomainPtr is resolved to the internal virDomainObjPtr,
all following code is moved.
This will allow the new v3 API entry points to call into the
same shared internal migration functions
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
qemuDomainFormatXML helper method
* src/qemu/qemu_driver.c: Remove all migration code
* src/qemu/qemu_migration.c, src/qemu/qemu_migration.h: Add
all migration code.
Move the qemudStartVMDaemon and qemudShutdownVMDaemon
methods into a separate file, renaming them to
qemuProcessStart, qemuProcessStop. All helper methods
called by these are also moved & renamed to match
* src/Makefile.am: Add qemu_process.c/.h
* src/qemu/qemu_command.c: Add qemuDomainAssignPCIAddresses
* src/qemu/qemu_command.h: Add VNC port min/max
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add
domain event queue helpers
* src/qemu/qemu_driver.c, src/qemu/qemu_driver.h: Remove
all QEMU process startup/shutdown functions
* src/qemu/qemu_process.c, src/qemu/qemu_process.h: Add
all QEMU process startup/shutdown functions
To allow the APIs to be used from separate files, move the domain
lock / job helper code into qemu_domain.c
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: Add domain lock
/ job code
* src/qemu/qemu_driver.c: Remove domain lock / job code
Move the code for handling the QEMU virDomainObjPtr private
data, and custom XML namespace into a separate file
* src/qemu/qemu_domain.c, src/qemu/qemu_domain.h: New file
for private data & namespace code
* src/qemu/qemu_driver.c, src/qemu/qemu_driver.h: Remove
private data & namespace code
* src/qemu/qemu_driver.h, src/qemu/qemu_command.h: Update
includes
* src/Makefile.am: Add src/qemu/qemu_domain.c
