AFAIK there aren't any cases where we will/should hit the old code
path for our supported qemu versions, so drop the old code.
Massive test suite churn follows
Reviewed-by: Andrea Bolognani <abologna@redhat.com>
Signed-off-by: Cole Robinson <crobinso@redhat.com>
Our test data used a lot of different qemu binary paths and some
of them were based on downstream systems.
Note that there is one file where I had to add "accel=kvm" because
the qemuargv2xml code parses "/usr/bin/kvm" as virt type="kvm".
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Per-domain directories were introduced in order to be able to
completely separate security labels for each domain (commit
f1f68ca334). However when the domain
name is long (let's say a ridiculous 110 characters), we cannot
connect to the monitor socket because on length of UNIX socket address
is limited. In order to get around this, let's shorten it in similar
fashion and in order to avoid conflicts, throw in an ID there as well.
Also save that into the status XML and load the old status XMLs
properly (to clean up after older domains). That way we can change it
in the future.
The shortening can be seen in qemuxml2argv tests, for example in the
hugepages-pages2 case.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Just recently, qemu forbade specifying format for sourceless
disks (qemu commit 39c4ae941ed992a3bb5). It kind of makes sense.
If there's no file to open, why specify its format. Anyway, I
have a domain like this:
<disk type='file' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hda' bus='ide'/>
<readonly/>
<address type='drive' controller='0' bus='0' target='0' unit='0'/>
</disk>
and obviously I am unable to start it. Therefore, a fix on our
side is needed too.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
As of QEMU 0.10.0 the -drive format= parameter was added,
so the QEMU driver can assume it is always available.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Back in
commit bd6c46fa0c
Author: Juerg Haefliger <juerg.haefliger@hp.com>
Date: Mon Jan 31 06:42:57 2011 -0500
tests: handle backspace-newline pairs in test input files
all the test argv files were line wrapped so that the args
were less than 80 characters.
The way the line wrapping was done turns out to be quite
undesirable, because it often leaves multiple parameters
on the same line. If we later need to add or remove
individual parameters, then it leaves us having to redo
line wrapping.
This commit changes the line wrapping so that every
single "-param value" is one its own new line. If the
"value" is still too long, then we break on ',' or ':'
or ' ' as needed.
This means that when we come to add / remove parameters
from the test files line, the patch diffs will only
ever show a single line added/removed which will greatly
simplify review work.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
On my machine, a guest fails to boot if it has a sound card, but not
graphical device/display is configured, because pulseaudio fails to
initialize since it can't access $HOME.
A workaround is removing the audio device, however on ARM boards there
isn't any option to do that, so -nographic always fails.
Set QEMU_AUDIO_DRV=none if no <graphics> are configured. Unfortunately
this has massive test suite fallout.
Add a qemu.conf parameter nographics_allow_host_audio, that if enabled
will pass through QEMU_AUDIO_DRV from sysconfig (similar to
vnc_allow_host_audio)
When support for was added for PCI multifunction cards (in commit
9f8baf, first included in libvirt 0.9.3), it was done by always
turning on the multifunction bit for all PCI devices. Since that time
it has been realized that this is not an ideal solution, and that the
multifunction bit must be selectively turned on. For example, see
https://bugzilla.redhat.com/show_bug.cgi?id=728174
and the discussion before and after
https://www.redhat.com/archives/libvir-list/2011-September/msg01036.html
This patch modifies multifunction support so that the multifunction=on
option is only added to the qemu commandline for a device if its PCI
<address> definition has the attribute "multifunction='on'", e.g.:
<address type='pci' domain='0x0000' bus='0x00'
slot='0x04' function='0x0' multifunction='on'/>
In practice, the multifunction bit should only be turned on if
function='0' AND other functions will be used in the same slot - it
usually isn't needed for functions 1-7 (although there are apparently
some exceptions, e.g. the Intel X53 according to the QEMU source
code), and should never be set if only function 0 will be used in the
slot. The test cases have been changed accordingly to illustrate.
With this patch in place, if a user attempts to assign multiple
functions in a slot without setting the multifunction bit for function
0, libvirt will issue an error when the domain is defined, and the
define operation will fail. In the future, we may decide to detect
this situation and automatically add multifunction=on to avoid the
error; even then it will still be useful to have a manual method of
turning on multifunction since, as stated above, there are some
devices that excpect it to be turned on for all functions in a slot.
A side effect of this patch is that attempts to use the same PCI
address for two different devices will now log an error (previously
this would cause the domain define operation to fail, but there would
be no log message generated). Because the function doing this log was
almost completely rewritten, I didn't think it worthwhile to make a
separate patch for that fix (the entire patch would immediately be
obsoleted).
