Currently we only allow /dev/random and /dev/hwrng as host input
for <rng><backend model='random'/> device. This was added after
various upstream discussions in commit 4932ef45
However this restriction has generated quite a few complaints over
the years, so a new discussion was initiated:
http://www.redhat.com/archives/libvir-list/2016-April/msg00987.html
Several people suggested removing the restriction, and nobody really
spoke up to defend it. So this patch drops the path restriction
entirely
https://bugzilla.redhat.com/show_bug.cgi?id=1074464
This controller provides a single PCIe port on a new root. It is
similar to pci-expander-bus, intended to provide a bus that can be
associated with a guest-identifiable NUMA node, but is for
machinetypes with PCIe rather than PCI (e.g. q35-based machinetypes).
Aside from PCIe vs. PCI, the other main difference is that a
pci-expander-bus has a companion pci-bridge that is automatically
attached along with it, but pcie-expander-bus has only a single port,
and that port will only connect to a pcie-root-port, or to a
pcie-switch-upstream-port. In order for the bus to be of any use in
the guest, it must have either a pcie-root-port or a
pcie-switch-upstream-port attached (and one or more
pcie-switch-downstream-ports attached to the
pcie-switch-upstream-port).
This is a standard PCI root bus (not a bridge) that can be added to a
440fx-based domain. Although it uses a PCI slot, this is *not* how it
is connected into the PCI bus hierarchy, but is only used for
control. Each pci-expander-bus provides 32 slots (0-31) that can
accept hotplug of standard PCI devices.
The usefulness of pci-expander-bus relative to a pci-bridge is that
the NUMA node of the bus can be specified with the <node> subelement
of <target>. This gives guest-side visibility to the NUMA node of
attached devices (presuming that management apps only assign a device
to a bus that has a NUMA node number matching the node number of the
device on the host).
Each pci-expander-bus also has a "busNr" attribute. The expander-bus
itself will take the busNr specified, and all buses that are connected
to this bus (including the pci-bridge that is automatically added to
any expander bus of model "pxb" (see the next commit)) will use
busNr+1, busNr+2, etc, and the pci-root (or the expander-bus with next
lower busNr) will use bus numbers lower than busNr.
This is especially useful for "bus", since the bus of a device's pci
address is matched to the "index" of a controller to determine which
bus it will be connected to, and "index" is always specified in
decimal - being able to specify both in decimal at least makes it
easier to assure a device is being assigned to the correct bus when it
is added. For the other attributes, it is just a convenience.
(MB: the parser already allows for any of these attributes to be given
in decimal, and there are even examples floating around on the
internet that give them in decimal rather than hex (written in the
days before virsh did schema validation on all XML). This only updates
the schema to match the parser.)
nwfilter.rng defines uint16range and uint32range, but in a different
manner (it also allows a variable name as the value, rather than just
a decimal or hex number). I wanted to add uint16range to
basictypes.rng, but my desired definition was parallel to those for
uint8range and uint24range which are defined in basictypes.rng - they
*don't* allow a variable name for the value.
The simplest path to make everyone happy is to make the "plain"
versions in basictypes.rng have simpler names - "uint8", "uint16", and
"uint24". This patch renames uint8range and uint24range to uint8 and
uint24, while the next patch will add uint16.
The pcie-switch-downstream-port and pcie-root-port controllers have
only a single slot, numbered 0, and the greate majority of all guest
PCI devices are plugged into function 0 of whatever slot they're
using. The parser makes these optional, setting them to 0 when not
specified, and it's logical for the schema to also make them optional.
This patch adds new xml element, and so we can have the option of
also having perf events enabled immediately at startup.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Message-id: 1459171833-26416-6-git-send-email-qiaowei.ren@intel.com
This patch adds support for "vpindex", "runtime", "synic",
"stimer", and "vendor_id" features available in qemu 2.5+.
- When Hyper-V "vpindex" is on, guest can use MSR HV_X64_MSR_VP_INDEX
to get virtual processor ID.
- Hyper-V "runtime" enlightement feature allows to use MSR
HV_X64_MSR_VP_RUNTIME to get the time the virtual processor consumes
running guest code, as well as the time the hypervisor spends running
code on behalf of that guest.
- Hyper-V "synic" stands for Synthetic Interrupt Controller, which is
lapic extension controlled via MSRs.
- Hyper-V "stimer" switches on Hyper-V SynIC timers MSR's support.
Guest can setup and use fired by host events (SynIC interrupt and
appropriate timer expiration message) as guest clock events
- Hyper-V "reset" allows guest to reset VM.
- Hyper-V "vendor_id" exposes hypervisor vendor id to guest.
Signed-off-by: Nikolay Shirokovskiy <nshirokovskiy@virtuozzo.com>
Signed-off-by: John Ferlan <jferlan@redhat.com>
When reading in an XML definition for a SCSI target device, the name
property of struct scsi_target refers to the @target element.
Let's fix this obvious typo and also extend the XML schema to provide
validation.
Signed-off-by: Bjoern Walk <bwalk@linux.vnet.ibm.com>
Most hypervisors use Hardware Assisted Paging by default and don't
require specifying the feature in domain conf. But some hypervisors
support disabling HAP on a per-domain basis. To enable HAP by default
yet provide a knob to disable it, extend the <hap> feature with a
'state=on|off' attribute, similar to <pvspinlock> and <vmport> features.
In the absence of <hap>, the hypervisor default (on) is used. <hap>
without the state attribute would be the same as <hap state='on'/> for
backwards compatibility. And of course <hap state='off'/> disables hap.
Signed-off-by: Jim Fehlig <jfehlig@suse.com>
If we expose this information, which is one byte in every PCI config
file, we let all mgmt apps know whether the device itself is an endpoint
or not so it's easier for them to decide whether such device can be
passed through into a VM (endpoint) or not (*-bridge).
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1317531
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
The docs claims the cache attribute of the disk <driver>
element supports 'default' as one of its permissible values,
but such configuration fails virt-xml-validate. Add 'default'
as one of the cache attribute choices in domaincommon.rng.
Extend the chardev source XML so that there is a new optional
<log/> element, which is applicable to all character device
backend types. For example, to log output of a TCP backed
serial port
<serial type='tcp'>
<source mode='connect' host='127.0.0.1' service='9999'/>
<protocol type='raw'/>
<log file='/var/log/libvirt/qemu/demo-serial0.log' append='on'/>
<target port='0'/>
</serial>
Not all hypervisors will support use of logfiles.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
This parameter represents top level period cgroup
that limits whole domain enforcement period for a quota
Signed-off-by: Alexander Burluka <aburluka@virtuozzo.com>
This attribute is used to extend secondary PCI bar and expose it to the
guest as 64bit memory. It works like this: attribute vram is there to
set size of secondary PCI bar and guest sees it as 32bit memory,
attribute vram64 can extend this secondary PCI bar. If both attributes
are used, guest sees two memory bars, both address the same memory, with
the difference that the 32bit bar can address only the first part of the
whole memory.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1260749
Signed-off-by: Pavel Hrdina <phrdina@redhat.com>
Add Spice graphics gl attribute. qemu 2.6 should have -spice gl=on argument to
enable opengl rendering context (patches on the ML). This is necessary to
actually enable virgl rendering.
Add a qemuxml2argv test for virtio-gpu + spice with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
This change allows to use "host" as a GIC version in the domain XML.
Since we'll need to update the virGICVersion enumeration to support
new GIC versions anyway, it makes sense to be a bit more strict in
the schema as well and reject values that are not in the enumeration.
Add a new storage pool source device attribute 'part_separator=[yes|no]'
in order to allow a 'disk' storage pool using a device mapper multipath
device to not add the "p" partition separator to the generated device
name when libvirt_parthelper is run.
This will allow libvirt to find device mapper multipath devices which were
configured in /etc/multipath.conf to use 'user_friendly_names' or custom
'alias' names for the LUN.
Excessive memory balloon inflation can cause invocation of OOM-killer,
when Linux is under severe memory pressure. QEMU memballoon device
has a feature to release some memory at the last moment before some
process will be get killed by OOM-killer.
Introduce a new optional balloon device attribute 'autodeflate' to
enable or disable this feature.
Allow <name> and <uuid> anywhere under <domain>, not just at the top:
error:XML document failed to validate against schema: Unable to validate
doc against /usr/share/libvirt/schemas/domain.rng
Expecting an element name, got nothing
Invalid sequence in interleave
Element domain failed to validate content
Introduced with the first RelaxNG schema in commit c642103.
https://bugzilla.redhat.com/show_bug.cgi?id=1292131
Currently, there is no possibility for user to specify desired behaviour of
output to file - truncate or append. This patch adds an ability to explicitly
specify that user wants to preserve file's content on reopen.
Signed-off-by: Dmitry Mishin <dim@virtuozzo.com>
Using more than 4TiB of memory per NUMA node would not be possible to
express in the XML without violating the schema. Not that such boxes
would be common, but we should use a longer type at this point.
The pattern is not necessary since libvirt redefines the type already in
basictypes.rng with the same pattern.
To be used by the family of virtio input devices:
<input type='mouse' bus='virtio'/>
<input type='tablet' bus='virtio'/>
<input type='keyboard' bus='virtio'/>
https://bugzilla.redhat.com/show_bug.cgi?id=1231114
qemu 2.5 provides virtio video device. It can be used with -device
virtio-vga for primary devices, or -device virtio-gpu for non-vga
devices. However, only the primary device (VGA) is supported with this
patch.
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=1195176
Signed-off-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
'model' attribute was added to a panic device but only one panic
device is allowed. This patch changes panic device presence
from 'optional' to 'zeroOrMore'.
Libvirt already has two types of panic devices - pvpanic and pSeries firmware.
This patch introduces the 'model' attribute and a new type of panic device.
'isa' model is for ISA pvpanic device.
'pseries' model is a default value for pSeries guests.
'hyperv' model is the new type. It's used for Hyper-V crash.
Schema and docs are updated for the new attribute.
Adjust the config code so that it does not enforce that target memory
node is specified. To avoid breakage, adjust the qemu memory hotplug
config checker to disallow such config for now.
Adds a new interface type using UDP sockets, this seems only applicable
to QEMU but have edited tree-wide to support the new interface type.
The interface type required the addition of a "localaddr" (local
address), this then maps into the following xml and qemu call.
<interface type='udp'>
<mac address='52:54:00:5c:67:56'/>
<source address='127.0.0.1' port='11112'>
<local address='127.0.0.1' port='22222'/>
</source>
<model type='virtio'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x07' function='0x0'/>
</interface>
QEMU call:
-net socket,udp=127.0.0.1:11112,localaddr=127.0.0.1:22222
Notice the xml "local" entry becomes the "localaddr" for the qemu call.
reference:
http://lists.gnu.org/archive/html/qemu-devel/2011-11/msg00629.html
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
This patch adds feature for lxc containers to inherit namespaces.
This is very similar to what lxc-tools or docker provides. Look
for "man lxc-start" and you will find that you can pass command
args as [ --share-[net|ipc|uts] name|pid ]. Or check out docker
networking option in which you can give --net=container:NAME_or_ID
as an option for sharing +namespace.
>From this patch you can add extra libvirt option to share
namespace in following way.
<lxc:namespace>
<lxc:sharenet type='netns' value='red'/>
<lxc:shareipc type='pid' value='12345'/>
<lxc:shareuts type='name' value='container1'/>
</lxc:namespace>
The netns option is specific to sharenet. It can be used to
inherit from existing network namespace.
Co-authored: Daniel P. Berrange <berrange@redhat.com>
This controller can be connected only to a port on a
pcie-switch-upstream-port. It provides a single hotpluggable port that
will accept any PCI or PCIe device, as well as any device requiring a
pcie-*-port (the only current example of such a device is the
pcie-switch-upstream-port).
This controller can be connected only to a pcie-root-port or a
pcie-switch-downstream-port (which will be added in a later patch),
which is the reason for the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_PORT. A pcie-switch-upstream-port provides
32 ports (slot=0 to slot=31) on the downstream side, which can only
have pci controllers of model "pcie-switch-downstream-port" plugged
into them, which is the reason for the other new connect type
VIR_PCI_CONNECT_TYPE_PCIE_SWITCH.
This controller can be connected (at domain startup time only - not
hotpluggable) only to a port on the pcie root complex ("pcie-root" in
libvirt config), hence the new connect type
VIR_PCI_CONNECT_TYPE_PCIE_ROOT. It provides a hotpluggable port that
will accept any PCI or PCIe device.
New attributes must be added to the controller <target> subelement for
this - chassis and port are guest-visible option values that will be
set by libvirt with values derived from the controller's index and pci
address information.
There are some configuration options to some types of pci controllers
that are currently automatically derived from other parts of the
controller's configuration. For example, in qemu a pci-bridge
controller has an option that is called "chassis_nr"; up until now
libvirt has always set chassis_nr to the index of the pci-bridge. So
this:
<controller type='pci' model='pci-bridge' index='2'/>
will always result in:
-device pci-bridge,chassis_nr=2,...
on the qemu commandline. In the future we may decide there is a better
way to derive that option, but even in that case we will need for
existing domains to retain the same chassis_nr they were using in the
past - that is something that is visible to the guest so it is part of
the guest ABI and changing it would lead to problems for migrating
guests (or just guests with very picky OSes).
The <target> subelement has been added as a place to put the new
"chassisNr" attribute that will be filled in by libvirt when it
auto-generates the chassisNr; it will be saved in the config, then
reused any time the domain is started:
<controller type='pci' model='pci-bridge' index='2'>
<model type='pci-bridge'/>
<target chassisNr='2'/>
</controller>
The one oddity of all this is that if the controller configuration
is changed (for example to change the index or the pci address
where the controller is plugged in), the items in <target> will
*not* be re-generated, which might lead to conflict. I can't
really see any way around this, but fortunately if there is a
material conflict qemu will let us know and we will pass that on
to the user.
This new subelement is used in PCI controllers: the toplevel
*attribute* "model" of a controller denotes what kind of PCI
controller is being described, e.g. a "dmi-to-pci-bridge",
"pci-bridge", or "pci-root". But in the future there will be different
implementations of some of those types of PCI controllers, which
behave similarly from libvirt's point of view (and so should have the
same model), but use a different device in qemu (and present
themselves as a different piece of hardware in the guest). In an ideal
world we (i.e. "I") would have thought of that back when the pci
controllers were added, and used some sort of type/class/model
notation (where class was used in the way we are now using model, and
model was used for the actual manufacturer's model number of a
particular family of PCI controller), but that opportunity is long
past, so as an alternative, this patch allows selecting a particular
implementation of a pci controller with the "name" attribute of the
<model> subelement, e.g.:
<controller type='pci' model='dmi-to-pci-bridge' index='1'>
<model name='i82801b11-bridge'/>
</controller>
In this case, "dmi-to-pci-bridge" is the kind of controller (one that
has a single PCIe port upstream, and 32 standard PCI ports downstream,
which are not hotpluggable), and the qemu device to be used to
implement this kind of controller is named "i82801b11-bridge".
Implementing the above now will allow us in the future to add a new
kind of dmi-to-pci-bridge that doesn't use qemu's i82801b11-bridge
device, but instead uses something else (which doesn't yet exist, but
qemu people have been discussing it), all without breaking existing
configs.
(note that for the existing "pci-bridge" type of PCI controller, both
the model attribute and <model> name are 'pci-bridge'. This is just a
coincidence, since it turns out that in this case the device name in
qemu really is a generic 'pci-bridge' rather than being the name of
some real-world chip)
This patch provides support for the new watchdog model "diag288".
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
This patch provides support for a new watchdog action "inject-nmi" which
allows to define an inject of a non-maskable interrupt into a guest.
Signed-off-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Reviewed-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Currently the grammar uses "none" for a "valid" Disk Storage Pool
format type; however, virStoragePoolFormatDisk uses "unknown" so
virt-xml-validate will fail to validate when "unknown" is found
Defining a domain with a SCSI disk attached via a hostdev
tag and a source address unit value longer than two digits
causes an error when editing the domain with virsh edit,
even if no changes are made to the domain definition.
The error suggests invalid XML, somewhere:
# virsh edit lmb_guest
error: XML document failed to validate against schema:
Unable to validate doc against /usr/local/share/libvirt/schemas/domain.rng
Extra element devices in interleave
Element domain failed to validate content
The virt-xml-validate tool fails with a similar error:
# virt-xml-validate lmb_guest.xml
Relax-NG validity error : Extra element devices in interleave
lmb_guest.xml:17: element devices: Relax-NG validity error :
Element domain failed to validate content
lmb_guest.xml fails to validate
The hostdev tag requires a source address to be specified,
which includes bus, target, and unit address attributes.
According to the SCSI Architecture Model spec (section
4.9 of SAM-2), a LUN address is 64 bits and thus could be
up to 20 decimal digits long. Unfortunately, the XML
schema limits this string to just two digits. Similarly,
the target field can be up to 32 bits in length, which
would be 10 decimal digits.
# lsscsi -xx
[0:0:19:0x4022401100000000] disk IBM 2107900 3.44 /dev/sda
# lsscsi
[0:0:19:1074872354]disk IBM 2107900 3.44 /dev/sda
# cat lmb_guest.xml
<domain type='kvm'>
<name>lmb_guest</name>
<memory unit='MiB'>1024</memory>
...trimmed...
<devices>
<controller type='scsi' model='virtio-scsi' index='0'/>
<hostdev mode='subsystem' type='scsi'>
<source>
<adapter name='scsi_host0'/>
<address bus='0' target='19' unit='1074872354'/>
</source>
</hostdev>
...trimmed...
Since the reference unit and target fields are used in
several places in the XML schema, create a separate one
specific for SCSI Logical Units that will permit the
greater length. This permits both the validation utility
and the virsh edit command to succeed when a hostdev
tag is included.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
Reviewed-by: Stefan Zimmermann <stzi@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1220527
This type of information defines attributes of a system
baseboard. With one exception: board type is yet not implemented
in qemu so it's not introduced here either.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Commit id '887dd362' added support for a netfs pool format type 'cifs'
and 'gluster' in order to add rng support for Samba and glusterfs netfs
pools. Originally, the CIFS type support was added as part of commit
id '61fb6979'. Eventually commit id 'b325be12' fixed the gluster rng
definition to match expectations.
As it turns out the CIFS rng needed a similar change since the directory
path is not an absDirPath, rather just a dirPath will be required.
https://bugzilla.redhat.com/show_bug.cgi?id=1228007
When attaching a scsi volume lun via the attach-device --config or
--persistent options, there was no translation of the source pool
like there was for the live path, thus the attempt to modify the config
would fail since not enough was known about the disk.
I see no reason to duplicate this list of architectures. This also allows
more guest architectures to be used with libvirt (like the mips64el qemu
machine I am trying to run).
Signed-off-by: James Cowgill <james410@cowgill.org.uk>
The network name is currently of type "deviceName" but it should be
"text" as name is defined in the network.rng.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
The XML parser sets a default <mode> if none is explicitly passed in.
This is then used at pool/vol creation time, and unconditionally reported
in the XML.
The problem with this approach is that it's impossible for other code
to determine if the user explicitly requested a storage mode. There
are some cases where we want to make this distinction, but we currently
can't.
Handle <mode> parsing like we handle <owner>/<group>: if no value is
passed in, set it to -1, and adjust the internal consumers to handle
it.
As of netcf-0.2.8, netcf supports configuring multipl IPv4 addresses,
as well as simultaneously configuring dhcp and static IPv4 addresses,
on a single interface. This patch updates libvirt's interface.rng to
allow such configurations.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1223688
https://bugzilla.redhat.com/show_bug.cgi?id=998813
Like usb-serial, the pci-serial device allows a serial device to be
attached to PCI bus. An example XML looks like this:
<serial type='dev'>
<source path='/dev/ttyS2'/>
<target type='pci-serial' port='0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</serial>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Two new domain configuration XML elements are added to enable/disable
the protected key management operations for a guest:
<domain>
...
<keywrap>
<cipher name='aes|dea' state='on|off'/>
</keywrap>
...
</domain>
Signed-off-by: Tony Krowiak <akrowiak@linux.vnet.ibm.com>
Signed-off-by: Viktor Mihajlovski <mihajlov@linux.vnet.ibm.com>
Signed-off-by: Daniel Hansel <daniel.hansel@linux.vnet.ibm.com>
Reviewed-by: Boris Fiuczynski <fiuczy@linux.vnet.ibm.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Some platforms, like aarch64, don't have APIC but GIC. So there's
no reason to have <apic/> feature turned on. However, we are
still missing <gic/> feature. This commit introduces the feature
to XML parser and formatter, adds documentation and updates RNG
schema.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
A new feature that can be turned on or off.
The QEMU machine vmport option allows to set the VMWare IO port
emulation. This emulation is useful for absolute pointer input when the
guest has vmware input drivers, and is enabled by default for kvm.
However it is unnecessary for Spice-enabled VM, since the agent already
handles absolute pointer and multi-monitors. Furthermore, it prevents
Spice from switching to relative input since the regular ps/2 pointer
driver is replaced by the vmware driver. It is thus advised to disable
vmport when using a Spice VM. This will permit the Spice client to
switch from absolute to relative pointer, as it may be required for
certain games or applications.
The phyp driver stuffed it into a DomainDefPtr during its attachdevice
routine, but the value is never advertised via capabilities so it should
be safe to drop.
Have the phyp driver use OSTYPE_LINUX, which is what it advertises via
capabilities.
Adding a new XML element 'iothreadids' in order to allow defining
specific IOThread ID's rather than relying on the algorithm to assign
IOThread ID's starting at 1 and incrementing to iothreads count.
This will allow future patches to be able to add new IOThreads by
a specific iothread_id and of course delete any exisiting IOThread.
Each iothreadids element will have 'n' <iothread> children elements
which will have attribute "id". The "id" will allow for definition
of any "valid" (eg > 0) iothread_id value.
On input, if any <iothreadids> <iothread>'s are provided, they will
be marked so that we only print out what we read in.
On input, if no <iothreadids> are provided, the PostParse code will
self generate a list of ID's starting at 1 and going to the number
of iothreads defined for the domain (just like the current algorithm
numbering scheme). A future patch will rework the existing algorithm
to make use of the iothreadids list.
On output, only print out the <iothreadids> if they were read in.
The PortNumber data type is declared to derive from 'short'.
Unfortunately this is an signed type, so validates the range
[-32,768, 32,767] which excludes valid port numbers between
32767 and 65535.
We can't use 'unsignedShort', since we need -1 to be a valid
port number too.
This change is to use 'int' and set an explicit max boundary
instead of relying on the data types' built-in max.
One of the existing tests is changed to use a high port number
to validate the schema.
https://bugzilla.redhat.com/show_bug.cgi?id=1214664
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
According to docs, using 'lun' as a value for device attribute is only valid
with disk types 'block' and 'network'. However current RNG schema also allows
a combination type='file' device='lun' which results in a successfull
xml validation, but fails at qemuBuildCommandLine.
Besides fixing the RNG schema, this patch also adds a qemuxml2argvtest
for this case.
https://bugzilla.redhat.com/show_bug.cgi?id=1210669
The <inbound/> element to <bandwidth/> has several attributes from
which two are mandatory. Well, from two at least one has to be
present: @average or @floor or both. Instead of inventing crazy RNG
schema, let's make all the attributes optional there and rely on our
parsing code to correctly handle the situation.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
On IRC, Hydrar pointed a problem where 'virsh edit' failed on
his domain created through an ISCSI pool managed by virt-manager,
all because the XML included a block device with colons in the
name.
* docs/schemas/basictypes.rng (absFilePath): Add colon as safe.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.xml: New file.
* tests/qemuxml2argvdata/qemuxml2argv-disk-iscsi.args: Likewise.
* tests/qemuxml2argvtest.c (mymain): Test it.
Signed-off-by: Eric Blake <eblake@redhat.com>
When using QEMU's 9pfs the target "dir" element is not necessarily an
absolute path but merely an arbitrary identifier. So validation in that
case currently fails with the misleading
$ virt-xml-validate /tmp/test.xml
Relax-NG validity error : Extra element devices in interleave
/tmp/test.xml:24: element devices: Relax-NG validity error : Element domain failed to validate content
/tmp/test.xml fails to validate
This patch adds code that parses and formats configuration for memory
devices.
A simple configuration would be:
<memory model='dimm'>
<target>
<size unit='KiB'>524287</size>
<node>0</node>
</target>
</memory>
A complete configuration of a memory device:
<memory model='dimm'>
<source>
<pagesize unit='KiB'>4096</pagesize>
<nodemask>1-3</nodemask>
</source>
<target>
<size unit='KiB'>524287</size>
<node>1</node>
</target>
</memory>
This patch preemptively forbids use of the <memory> device in individual
drivers so the users are warned right away that the device is not
supported.
Add a XML element that will allow to specify maximum supportable memory
and the count of memory slots to use with memory hotplug.
To avoid possible confusion and misuse of the new element this patch
also explicitly forbids the use of the maxMemory setting in individual
drivers's post parse callbacks. This limitation will be lifted when the
support is implemented.
Wikipedia's list of common misspellings [1] has a machine-readable
version. This patch fixes those misspellings mentioned in the list
which don't have multiple right variants (as e.g. "accension", which can
be both "accession" and "ascension"), such misspellings are left
untouched. The list of changes was manually re-checked for false
positives.
[1] https://en.wikipedia.org/wiki/Wikipedia:Lists_of_common_misspellings/For_machines
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Midonet is an opensource virtual networking that over lays the IP
network between hypervisors. Currently, such networks can be made
with the openvswitch virtualport type.
This patch, defines the schema and documentation that will serve
as basis for the follow up patches that will add support to libvirt
for using Midonet virtual ports for its interfaces. The schema
definition requires that the port profile expresses its interfaceid
as part of the port profile. For that reason, this is part of the
patch too.
Signed-off-by: Antoni Segura Puimedon <toni+libvirt@midokura.com>
All the devices we have format their address as its last sub-element, so
let's change memballoon to follow suit. Also adjust RNG to allow any
order of them so 'virsh edit' doesn't shout at us.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Now that the size of guest's memory can be inferred from the NUMA
configuration (if present) make it optional to specify <memory>
explicitly.
To make sure that memory is specified add a check that some form of
memory size was specified. One side effect of this change is that it is
no longer possible to specify 0KiB as memory size for the VM, but I
don't think it would be any useful to do so. (I can imagine embedded
systems without memory, just registers, but that's far from what libvirt
is usually doing).
Forbidding 0 memory for guests also fixes a few corner cases where 0 was
not interpreted correctly and caused failures. (Arguments for numad when
using automatic placement, size of the balloon). This fixes problems
described in https://bugzilla.redhat.com/show_bug.cgi?id=1161461
Test case changes are added to verify that the schema change and code
behave correctly.
Our code supports that for ages. When using a <filterref/> to an
<interface/> several parameters can be passed to the filter. Later,
when building firewall rules, parameters are substituted for their
values. However, our RNG schema allowed only one parameter to be
passed.
Reported-by: Brian Rak <brak@gameservers.com>
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
Adding functionality to libvirt that will allow it
query the ethtool interface for the availability
of certain NIC HW offload features
Here is an example of the feature XML definition:
<device>
<name>net_eth4_90_e2_ba_5e_a5_45</name>
<path>/sys/devices/pci0000:00/0000:00:03.0/0000:08:00.1/net/eth4</path>
<parent>pci_0000_08_00_1</parent>
<capability type='net'>
<interface>eth4</interface>
<address>90:e2:ba:5e:a5:45</address>
<link speed='10000' state='up'/>
<feature name='rx'/>
<feature name='tx'/>
<feature name='sg'/>
<feature name='tso'/>
<feature name='gso'/>
<feature name='gro'/>
<feature name='rxvlan'/>
<feature name='txvlan'/>
<feature name='rxhash'/>
<capability type='80203'/>
</capability>
</device>
Signed-off-by: Ján Tomko <jtomko@redhat.com>
In commit edd1295e1d I've introduced an
XML element that allows to configure state of the network interface
link. Somehow the RNG schema hunk ended up in a weird place in the
network schema definition. Move it to the right place and add a test
case.
Note that the link state is set up via the monitor at VM startup so I
originally didn't think of adding a test case.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1173468
The element wasn't declared under the interleave thus it was required
always to be first. This made it inconvenient when pasting new stuff to
the XML manually in the "wrong" place.
The "virtio-mmio" is perfectly valid address type which we parse and
format correctly, but it's missing in our RNG schemas, hence editing a
domain with device having such address fails the validation.
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
At least Xen supports backend drivers in another domain (aka "driver
domain"). This patch introduces an XML config option for specifying the
backend domain name for <disk> and <interface> devices. E.g.
<disk>
<backenddomain name='diskvm'/>
...
</disk>
<interface type='bridge'>
<backenddomain name='netvm'/>
...
</interface>
In the future, same option will be needed for USB devices (hostdev
objects), but for now libxl doesn't have support for PVUSB.
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Add an XML attribute to allow disabling merge of rx buffers
on the host:
<interface ...>
...
<model type='virtio'/>
<driver ...>
<host mrg_rxbuf='off'/>
</driver>
</interface>
https://bugzilla.redhat.com/show_bug.cgi?id=1186886
In order for QEMU vCPU (and other) threads to run with RT scheduler,
libvirt needs to take care of that so QEMU doesn't have to run privileged.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178986
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
In our RNG schema we do allow multiple (different) seclabels per-domain,
but don't allow this for devices, yet we neither have a check in our XML parser,
nor in a post-parse callback. In that case we should allow multiple
(different) seclabels for devices as well.
There are some interface types (notably 'server' and 'client')
which instead of allowing the default set of elements and
attributes (like the rest do), try to enumerate only the elements
they know of. This way it's, however, easy to miss something. For
instance, the <address/> element was not mentioned at all. This
resulted in a strange behavior: when such interface was added
into XML, the address was automatically generated by parsing
code. Later, the formatted XML hasn't passed the RNG schema. This
became more visible once we've turned on the XML validation on
domain XML changes: appending an empty line at the end of
formatted XML (to trick virsh think the XML had changed) made
libvirt to refuse the very same XML it formatted.
Instead of trying to find each element and attribute we are
missing in the schema, lets just allow all the elements and
attributes like we're doing that for the rest of types. It's no
harm if the schema is wider than our parser allows.
Signed-off-by: Michal Privoznik <mprivozn@redhat.com>
https://bugzilla.redhat.com/show_bug.cgi?id=1130390
The listen address is not mandatory for <interface type='server'>
but when it's not specified, we've been formatting it as:
-netdev socket,listen=(null):5558,id=hostnet0
which failed with:
Device 'socket' could not be initialized
Omit the address completely and only format the port in the listen
attribute.
Also fix the schema to allow specifying a model.
This adds a new "localOnly" attribute on the domain element of the
network xml. With this set to "yes", DNS requests under that domain
will only be resolved by libvirt's dnsmasq, never forwarded upstream.
This was how it worked before commit f69a6b987d, and I found that
functionality useful. For example, I have my host's NetworkManager
dnsmasq configured to forward that domain to libvirt's dnsmasq, so I can
easily resolve guest names from outside. But if libvirt's dnsmasq
doesn't know a name and forwards it to the host, I'd get an endless
forwarding loop. Now I can set localOnly="yes" to prevent the loop.
Signed-off-by: Josh Stone <jistone@redhat.com>
Ploop is a pseudo device which makeit possible to access
to an image in a file as a block device. Like loop devices,
but with additional features, like snapshots, write tracker
and without double-caching.
It used in PCS for containers and in OpenVZ. You can manage
ploop devices and images with ploop utility
(http://git.openvz.org/?p=ploop).
Signed-off-by: Dmitry Guryanov <dguryanov@parallels.com>
QEMU supports feature specification with -cpu host and we just skip
using that. Since QEMU developers themselves would like to use this
feature, this patch modifies the code to work.
Resolves: https://bugzilla.redhat.com/show_bug.cgi?id=1178850
Signed-off-by: Martin Kletzander <mkletzan@redhat.com>
Make use of the ebtables functionality to be able to filter certain
parameters of icmpv6 packets. Extend the XML parser for icmpv6 types,
type ranges, codes, and code ranges. Extend the nwfilter documentation,
schema, and test cases.
Being able to filter icmpv6 types and codes helps extending the DHCP
snooper for IPv6 and filtering at least some parameters of IPv6's NDP
(Neighbor Discovery Protocol) packets. However, the filtering will not
be as good as the filtering of ARP packets since we cannot
check on IP addresses in the payload of the NDP packets.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
