We pass over the address/port start/end values many times so we put
them in structs.
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
Let users set the port range to be used for forward mode NAT:
...
<forward mode='nat'>
<nat>
<port start='1024' end='65535'/>
</nat>
</forward>
...
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
Support setting which public ip to use for NAT via attribute
address in subelement <nat> in <forward>:
...
<forward mode='nat'>
<address start='1.2.3.4' end='1.2.3.10'/>
</forward>
...
This will construct an iptables line using:
'-j SNAT --to-source <start>-<end>'
instead of:
'-j MASQUERADE'
Signed-off-by: Natanael Copa <ncopa@alpinelinux.org>
Signed-off-by: Laine Stump <laine@laine.org>
The conditional setting of cmdout in networkBuildDhcpDaemonCommandLine()
caused Coverity to complain that 'cmd' could be leaked if !cmdout. Since
the function is local and only called with cmdout being passed those checks
have been removed.
The fetch of 'ipdef' in networkRefreshDhcpDaemon() when the loop to fill
in ipv4def fails to find an ipv4 address with dhcp defined. The filled in
ipdef value was not used. Code was made unnecessary with commit it 2d5cd1.
The bandwidth plug and unplug functions were assuming that an
interface's bandwidth setting was always specified directly in the
domain's <interface> definition, but that's not necessarily true - it
could have been obtained from a <portgroup> definition in the network
definition. This patch fixes those functions to use
virDomainNetGetActualBandwidth(), which gets the bandwidth pointer
from iface->data.network.actual if it exists, otherwise returns
iface->bandwidth.
Remove extraneous check for 'netdef' when dereferencing for vlan.nTags.
Prior code would already check if netdef was NULL.
Coverity complained about a path where the 'vlan' was potentially valid,
but a prior checks may not have allocated 'iface->data.network.actual',
so like other paths it needs to be allocated on the fly.
Move the copying of vlan up earlier in networkAllocateActualDevice, so
that actual.type gets properly set.
Since the first assignment to vlan is redundant except in the case of
jumping immediately to validate from the start of the function,
eliminate its initial setting at the top of the function in favor of
calling the helper function virDomainNetGetActualVlan() (which doesn't
depend on the local vlan pointer being initialized) down at validate:
Signed-off-by: Laine Stump <laine@redhat.com>
If addition of rules in networkAddIptablesRules() failed the real error
was masked by error reported when trying to clean up the remaining
rules.
With this patch the original error message is saved and set back after
the removal is complete.
Commit 0211fd6e04 introduced regression
where newly defined networks were not made persistent.
This patch makes the network persistent on each successful definition.
This is yet another refinement to the fix for CVE-2012-3411:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
It turns out that it would be very intrusive to correctly backport the
entire --bind-dynamic option to older dnsmasq versions
(e.g. dnsmasq-2.48 that is used on RHEL6.x and CentOS 6.x), but very
simple to patch those versions to just use SO_BINDTODEVICE on all
their listening sockets (SO_BINDTODEVICE also has the desired effect
of permitting only traffic that was received on the interface(s) where
dnsmasq was set to listen.)
This patch modifies the dnsmasq capabilities detection to detect the
string:
--bind-interfaces with SO_BINDTODEVICE
in the output of "dnsmasq --version", and in that case realize that
using the old --bind-interfaces option is just as safe as
--bind-dynamic (and therefore *not* forbid creation of networks that
use public IP address ranges).
If -bind-dynamic is available, it is still preferred over
--bind-interfaces.
Note that this patch does no harm in upstream, or in any distro's
downstream if it happens to end up there, but builds for distros that
have a new enough dnsmasq to support --bind-dynamic do *NOT* need to
specifically backport this patch; it's only required for distro
releases that have dnsmasq too old to have --bind-dynamic (and those
distros will need to add the SO_BINDTODEVICE patch to dnsmasq,
*including the extra string in the --version output*, as well.
Somehow I managed to push the changes to this file with improper
indentation. This patch just re-indents, reformats the comment lines,
and re-groups a couple of multi-line strings so that they fit within
80 columns. The resulting binary should be identical.
A forgotten "!" in recently-modified code at the top of
networkRefreshDaemon() meant an improper early return, which led to 1)
dnsmasq config files not being updated from the newly modified config,
and 2) dnsmasq not being sent a SIGHUP so that it could learn about
the changes to the config.
virNetworkDefGetIpByIndex() returns NULL if there are no ip objects of
the requested type, and if there are no IP elements, then dnsmasq
shouldn't be running, so we can return early. Otherwise we should
rewrite the config files and send a SIGHUP.
This patch resolves the problem reported in:
https://bugzilla.redhat.com/show_bug.cgi?id=886663
The source of the problem was the fix for CVE 2011-3411:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
which was originally committed upstream in commit
753ff83a50. That commit improperly
removed the "--except-interface lo" from dnsmasq commandlines when
--bind-dynamic was used (based on comments in the latter bug).
It turns out that the problem reported in the CVE could be eliminated
without removing "--except-interface lo", and removing it actually
caused each instance of dnsmasq to listen on localhost on port 53,
which created a new problem:
If another instance of dnsmasq using "bind-interfaces" (instead of
"bind-dynamic") had already been started (or if another instance
started later used "bind-dynamic"), this wouldn't have any immediately
visible ill effects, but if you tried to start another dnsmasq
instance using "bind-interfaces" *after* starting any libvirt
networks, the new dnsmasq would fail to start, because there was
already another process listening on port 53.
(Subsequent to the CVE fix, another patch changed the network driver
to put dnsmasq options in a conf file rather than directly on the
dnsmasq commandline, but preserved the same options.)
This patch changes the network driver to *always* add
"except-interface=lo" to dnsmasq conf files, regardless of whether we use
bind-dynamic or bind-interfaces. This way no libvirt dnsmasq instances
are listening on localhost (and the CVE is still fixed).
The actual code change is miniscule, but must be propogated through all
of the test files as well.
I noticed that /var/lib/libvirt/dnsmasq/*.conf used the wrong word;
it was intended to match the wording in src/util/xml.c.
* src/network/bridge_driver.c (networkDnsmasqConfContents): Fix typo.
* tests/networkxml2confdata/*.conf: Update accordingly.
Currently, we are only keeping a inactive XML configuration
in status dir. This is no longer enough as we need to keep
this class_id attribute so we don't overwrite old entries
when the daemon restarts. However, since there has already
been release which has just <network/> as root element,
and we want to keep things compatible, detect that loaded
status file is older one, and don't scream about it.
Network should be notified if we plug in or unplug an
interface, so it can perform some action, e.g. set/unset
network part of QoS. However, we are doing this in very
early stage, so iface->ifname isn't filled in yet. So
whenever we want to report an error, we must use a different
identifier, e.g. the MAC address.
These classes can borrow unused bandwidth. Basically,
only egress qdsics can have classes, therefore we can
do this kind of traffic shaping only on host's outgoing,
that is domain's incoming traffic.
This patch changes how parameters are passed to dnsmasq. Instead of
being on the command line, the parameters are put into a file (one
parameter per line) and a commandline --conf-file= specifies the
location of the file. The file is located in the same directory as
the leases file.
Putting the dnsmasq parameters into a configuration file
allows them to be examined and more easily understood than
examining the command lines displayed by "ps ax". This is
especially true when a number of networks have been started.
When the use of dnsmasq was originally done, the required command line
was simple, but it has gotten more complicated over time and will
likely become even more complicated in the future.
Note: The test conf files have all been renamed .conf instead of
.argv, and tests/networkxml2xmlargvdata was moved to
tests/networkxml2xmlconfdata.
The DHCPv6 support includes IPV6 dhcp-range and dhcp-host for one
IPv6 subnetwork on one interface. This support will only work
if dnsmasq version >= 2.64; otherwise an error occurs if
dhcp-range or dhcp-host is specified for an IPv6 address.
Essentially, this change provides the same DHCP support for IPv6
that has been available for IPv4.
With dnsmasq >= 2.64, support for the RA service is also now provided
by dnsmasq (radvd is no longer used/started). (Although at least one
version of dnsmasq prior to 2.64 "supported" IPv6 Router
Advertisement, there were bugs (fixed in 2.64) that rendered it
unusable.)
Documentation and the network schema has been updated
to reflect the new support.
The attributes of a <network> element's <forward> element were
previously stored directly in the virNetworkDef object, but
virNetworkUpdateForward() needs to operate on a <forward> in
isolation, so this patchs pulls out all those attributes into a
separate virNetworkForwardDef struct (and shortens their names
appropriately). This new object is contained in the virNetworkDef, not
pointed to by it, so there is no extra memory management.
This patch makes no functional changes, it only changes, e.g.,
"nForwardIfs" to "forward.nifs".
Since there is only a single virNetworkDNSDef for any virNetworkDef,
and it's trivial to determine whether or not it contains any real
data, it's much simpler (and fits more uniformly with the parse
function calling sequence of the parsers for many other objects that
are subordinates of virNetworkDef) if virNetworkDef *contains* an
virNetworkDNSDef rather than pointing to one.
Since it is now just a part of another object rather than its own
object, it no longer makes sense to have a *Free() function, so that
is changed to a *Clear() function.
More importantly though, ParseXML and Clear functions are needed for
the individual items contained in a virNetworkDNSDef (srv, txt, and
host records), but none of them have a *Clear(), and only two of the
three had *ParseXML() functions (both of which used a non-uniform
arglist). Those problems are cleared up by this patch - it splits the
higher-level Clear function into separate functions for each of the
three, creates a parse for txt records, and cleans up the srv and host
parsers, so we now have all the utility functions necessary to
implement virNetworkDefUpdateDNS(Host|Srv|Txt).
This shortens the name of the structs for srv and txt, and their
instances in virNetworkDNSDef, to be more compact and uniform with the
naming of the dns host array. It also changes the type of ntxts, etc
from unsigned int to size_t, so that they can be used directly as args
to VIR_*_ELEMENT.
This resolves: https://bugzilla.redhat.com/show_bug.cgi?id=767057
It was possible to define a network with <forward mode='bridge'> that
had both a bridge device and a forward device defined. These two are
mutually exclusive by definition (if you are using a bridge device,
then this is a host bridge, and if you have a forward dev defined,
this is using macvtap). It was also possible to put <ip>, <dns>, and
<domain> elements in this definition, although those aren't supported
by the current driver (although it's conceivable that some other
driver might support that).
The items that are invalid by definition, are now checked in the XML
parser (since they will definitely *always* be wrong), and the others
are checked in networkValidate() in the network driver (since, as
mentioned, it's possible that some other network driver, or even this
one, could some day support setting those).
This patch adds the capability for virtual guests to do IPv6
communication via a virtual network interface with no IPv6 (gateway)
addresses specified. This capability has always been enabled by
default for IPv4, but disabled for IPv6 for security concerns, and
because it requires the ip6tables command to be operational (which
isn't the case on a system with the ipv6 module completely disabled).
This patch adds a new attribute "ipv6" at the toplevel of a <network>
object. If ipv6='yes', the extra ip6tables rules required to permite
inter-guest communications are added when the network is started. If
it is 'no', or not present, those rules will not be added; thus the
default behavior doesn't change, so there should be no compatibility
issues with any existing installations.
Note that virtual guests cannot communication with the virtualization
host via this interface, because the following kernel tunable has
been set:
net.ipv6.conf.<bridge_interface_name>.disable_ipv6 = 1
This assures that the bridge interface will not have an IPv6
link-local (fe80::) address.
To control this behavior so that it is not enabled by default, the parameter
ipv6='yes' on the <network> statement has been added.
Documentation related to this patch has been updated.
The network schema has also been updated.
Currently to deal with auto-shutdown libvirtd must periodically
poll all stateful drivers. Thus sucks because it requires
acquiring both the driver lock and locks on every single virtual
machine. Instead pass in a "inhibit" callback to virStateInitialize
which drivers can invoke whenever they want to inhibit shutdown
due to existance of active VMs.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
The only important state that should prevent libvirtd shutdown
is from running VMs. Networks, host devices, network filters
and storage pools are all long lived resources that have no
significant in-memory state. They should not block shutdown.
This bug resolves CVE-2012-3411, which is described in the following
bugzilla report:
https://bugzilla.redhat.com/show_bug.cgi?id=833033
The following report is specifically for libvirt on Fedora:
https://bugzilla.redhat.com/show_bug.cgi?id=874702
In short, a dnsmasq instance run with the intention of listening for
DHCP/DNS requests only on a libvirt virtual network (which is
constructed using a Linux host bridge) would also answer queries sent
from outside the virtualization host.
This patch takes advantage of a new dnsmasq option "--bind-dynamic",
which will cause the listening socket to be setup such that it will
only receive those requests that actually come in via the bridge
interface. In order for this behavior to actually occur, not only must
"--bind-interfaces" be replaced with "--bind-dynamic", but also all
"--listen-address" options must be replaced with a single
"--interface" option. Fully:
--bind-interfaces --except-interface lo --listen-address x.x.x.x ...
(with --listen-address possibly repeated) is replaced with:
--bind-dynamic --interface virbrX
Of course libvirt can't use this new option if the host's dnsmasq
doesn't have it, but we still want libvirt to function (because the
great majority of libvirt installations, which only have mode='nat'
networks using RFC1918 private address ranges (e.g. 192.168.122.0/24),
are immune to this vulnerability from anywhere beyond the local subnet
of the host), so we use the new dnsmasqCaps API to check if dnsmasq
supports the new option and, if not, we use the "old" option style
instead. In order to assure that this permissiveness doesn't lead to a
vulnerable system, we do check for non-private addresses in this case,
and refuse to start the network if both a) we are using the old-style
options, and b) the network has a publicly routable IP
address. Hopefully this will provide the proper balance of not being
disruptive to those not practically affected, and making sure that
those who *are* affected get their dnsmasq upgraded.
(--bind-dynamic was added to dnsmasq in upstream commit
54dd393f3938fc0c19088fbd319b95e37d81a2b0, which was included in
dnsmasq-2.63)
In order to optionally take advantage of new features in dnsmasq when
the host's version of dnsmasq supports them, but still be able to run
on hosts that don't support the new features, we need to be able to
detect the version of dnsmasq running on the host, and possibly
determine from the help output what options are in this dnsmasq.
This patch implements a greatly simplified version of the capabilities
code we already have for qemu. A dnsmasqCaps device can be created and
populated either from running a program on disk, reading a file with
the concatenated output of "dnsmasq --version; dnsmasq --help", or
examining a buffer in memory that contains the concatenated output of
those two commands. Simple functions to retrieve capabilities flags,
the version number, and the path of the binary are also included.
bridge_driver.c creates a single dnsmasqCaps object at driver startup,
and disposes of it at driver shutdown. Any time it must be used, the
dnsmasqCapsRefresh method is called - it checks the mtime of the
binary, and re-runs the checks if the binary has changed.
networkxml2argvtest.c creates 2 "artificial" dnsmasqCaps objects at
startup - one "restricted" (doesn't support --bind-dynamic) and one
"full" (does support --bind-dynamic). Some of the test cases use one
and some the other, to make sure both code pathes are tested.
The virStateInitialize method and several cgroups methods were
using an 'int privileged' parameter or similar for dual-state
values. These are better represented with the bool type.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
bridge_driver.h: silence gcc warnings:
statement with no effect [-Wunused-value]
unused variable 'net' [-Wunused-variable]
virdrivermoduletest.c: don't require network driver module
if it hasn't been built.
The libvirt coding standard is to use 'function(...args...)'
instead of 'function (...args...)'. A non-trivial number of
places did not follow this rule and are fixed in this patch.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
When assigning the new persistent definition for a transient network
(thus making it persistent) the network needs to be marked persistent
before actually atempting to assign the definition.
Until now, the network undefine API was able to undefine only inactive
networks. The restriction doesn't make sense any more so this patch
implements changing networks to transient.
When a transient network was created some of the checks weren't run on
the definition allowing to start invalid networks.
This patch splits out code to the network validation function and
re-uses that code when creating transient networks.
The network driver didn't care about config files when a network was
destroyed, just when it was undefined leaving behind files for transient
networks.
This patch splits out the cleanup code to a helper function that handles
the cleanup if the inactive network object is being removed and re-uses
this code when getting rid of inactive networks.
The hosts file was created in the network definition function. This
patch moves the place the file is being created to the point where
dnsmasq is being started.
