Only one IPv4 DHCP definition is supported. Originally the code checked
for a multiple definition and returned an error, but the new domain
definition was already added to networks. This patch moves the check
before the newly defined network is added to active networks.
*src/network/bridge_driver.c: networkDefine(): - move multiple IPv4
addresses check before
definition is used.
The virDomainNetGetActualBridgeName and virDomainNetGetActualDirectDev
methods both return strings that point to data in the virDomainDefPtr
struct, and should therefore not be freed. The return values should
thus be 'const char *' not 'char *'.
* src/conf/domain_conf.c, src/conf/domain_conf.h: Mark const
* src/network/bridge_driver.c: Update to use a const char *
Move the ifaceMacvtapLinkDump and ifaceGetNthParent functions
into virnetdevvportprofile.c since they are specific to that
code. This avoids polluting the headers with the Linux specific
netlink data types
* src/util/interface.c, src/util/interface.h: Move
ifaceMacvtapLinkDump and ifaceGetNthParent functions and delete
remaining file
* src/util/virnetdevvportprofile.c: Add ifaceMacvtapLinkDump
and ifaceGetNthParent functions
* src/network/bridge_driver.c, src/nwfilter/nwfilter_gentech_driver.c,
src/nwfilter/nwfilter_learnipaddr.c, src/util/virnetdevmacvlan.c:
Remove include of interface.h
To match up with the existing virNetDevSetIPv4Address, rename
ifaceGetIPAddress to virNetDevGetIPv4Address
* util/interface.h, util/interface.c: Rename API
* network/bridge_driver.c: Update for API rename
In preparation for code re-organization, rename the Macvtap
management APIs to have the following patterns
virNetDevMacVLanXXXXX - macvlan/macvtap interface management
virNetDevVPortProfileXXXX - virtual port profile management
* src/util/macvtap.c, src/util/macvtap.h: Rename APIs
* src/conf/domain_conf.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/qemu/qemu_command.h,
src/qemu/qemu_driver.c, src/qemu/qemu_hotplug.c,
src/qemu/qemu_migration.c, src/qemu/qemu_process.c,
src/qemu/qemu_process.h: Update for renamed APIs
The src/util/network.c file is a dumping ground for many different
APIs. Split it up into 5 pieces, along functional lines
- src/util/virnetdevbandwidth.c: virNetDevBandwidth type & helper APIs
- src/util/virnetdevvportprofile.c: virNetDevVPortProfile type & helper APIs
- src/util/virsocketaddr.c: virSocketAddr and APIs
- src/conf/netdev_bandwidth_conf.c: XML parsing / formatting
for virNetDevBandwidth
- src/conf/netdev_vport_profile_conf.c: XML parsing / formatting
for virNetDevVPortProfile
* src/util/network.c, src/util/network.h: Split into 5 pieces
* src/conf/netdev_bandwidth_conf.c, src/conf/netdev_bandwidth_conf.h,
src/conf/netdev_vport_profile_conf.c, src/conf/netdev_vport_profile_conf.h,
src/util/virnetdevbandwidth.c, src/util/virnetdevbandwidth.h,
src/util/virnetdevvportprofile.c, src/util/virnetdevvportprofile.h,
src/util/virsocketaddr.c, src/util/virsocketaddr.h: New pieces
* daemon/libvirtd.h, daemon/remote.c, src/conf/domain_conf.c,
src/conf/domain_conf.h, src/conf/network_conf.c,
src/conf/network_conf.h, src/conf/nwfilter_conf.h,
src/esx/esx_util.h, src/network/bridge_driver.c,
src/qemu/qemu_conf.c, src/rpc/virnetsocket.c,
src/rpc/virnetsocket.h, src/util/dnsmasq.h, src/util/interface.h,
src/util/iptables.h, src/util/macvtap.c, src/util/macvtap.h,
src/util/virnetdev.h, src/util/virnetdevtap.c,
tools/virsh.c: Update include files
Rename the virVirtualPortProfileParams struct to be
virNetDevVPortProfile, and rename the APIs to match
this prefix.
* src/util/network.c, src/util/network.h: Rename port profile
APIs
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/conf/network_conf.c, src/conf/network_conf.h,
src/network/bridge_driver.c, src/qemu/qemu_hotplug.c,
src/util/macvtap.c, src/util/macvtap.h: Update for
renamed APIs/structs
steps to reproduce:
1. having a network xml file(named default.xml) like this one:
<network>
<name>default</name>
<uuid>c5322c4c-81d0-4985-a363-ad6389780d89</uuid>
<bridge name="virbr0" />
<forward/>
<ip address="192.168.122.1" netmask="255.255.255.0">
<dhcp>
<range start="192.168.122.2" end="192.168.122.254" />
</dhcp>
</ip>
</network>
in /etc/libvirt/qemu/networks/, and mark it as autostart:
$ ls -l /etc/libvirt/qemu/networks/autostart
total 0
lrwxrwxrwx 1 root root 14 Oct 12 14:02 default.xml -> ../default.xml
2. start libvirtd and the device virbr0 is not automatically up.
The reason is that the function virNetDevExists is now returns 1 if
the device exists, comparing to the former one returns 0 if the device
exists. But with only this fix will cause a segmentation fault(the same
steps as above) that is fixed by the second chunk of code.
The socket address APIs in src/util/network.h either take the
form virSocketAddrXXX, virSocketXXX or virSocketXXXAddr.
Sanitize this so everything is virSocketAddrXXXX, and ensure
that the virSocketAddr parameter is always the first one.
* src/util/network.c, src/util/network.h: Santize socket
address API naming
* src/conf/domain_conf.c, src/conf/network_conf.c,
src/conf/nwfilter_conf.c, src/network/bridge_driver.c,
src/nwfilter/nwfilter_ebiptables_driver.c,
src/nwfilter/nwfilter_learnipaddr.c,
src/qemu/qemu_command.c, src/rpc/virnetsocket.c,
src/util/dnsmasq.c, src/util/iptables.c,
src/util/virnetdev.c, src/vbox/vbox_tmpl.c: Update for
API renaming
Following the renaming of the bridge management APIs, we can now
split the source file into 3 corresponding pieces
* src/util/virnetdev.c: APIs for any type of network interface
* src/util/virnetdevbridge.c: APIs for bridge interfaces
* src/util/virnetdevtap.c: APIs for TAP interfaces
* src/util/virnetdev.c, src/util/virnetdev.h,
src/util/virnetdevbridge.c, src/util/virnetdevbridge.h,
src/util/virnetdevtap.c, src/util/virnetdevtap.h: Copied
from bridge.{c,h}
* src/util/bridge.c, src/util/bridge.h: Split into 3 pieces
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/openvz/openvz_driver.c, src/qemu/qemu_command.c,
src/qemu/qemu_conf.h, src/uml/uml_conf.c, src/uml/uml_conf.h,
src/uml/uml_driver.c: Update #include directives
The existing brXXX APIs in src/util/bridge.h are renamed to
follow one of three different conventions
- virNetDevXXX - operations for any type of interface
- virNetDevBridgeXXX - operations for bridge interfaces
- virNetDevTapXXX - operations for tap interfaces
* src/util/bridge.h, src/util/bridge.c: Rename all APIs
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Update for API renaming
Currently every caller of the brXXX APIs has to store the returned
errno value and then raise an error message. This results in
inconsistent error messages across drivers, additional burden on
the callers and makes the error reporting inaccurate since it is
hard to distinguish different scenarios from 1 errno value.
* src/util/bridge.c: Raise errors instead of returning errnos
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/qemu/qemu_command.c, src/uml/uml_conf.c,
src/uml/uml_driver.c: Remove error reporting code
The bridge management APIs in src/util/bridge.c require a brControl
object to be passed around. This holds the file descriptor for the
control socket. This extra object complicates use of the API for
only a minor efficiency gain, which is in turn entirely offset by
the need to fork/exec the brctl command for STP configuration.
This patch removes the 'brControl' object entirely, instead opening
the control socket & closing it again within the scope of each method.
The parameter names for the APIs are also made to consistently use
'brname' for bridge device name, and 'ifname' for an interface
device name. Finally annotations are added for non-NULL parameters
and return check validation
* src/util/bridge.c, src/util/bridge.h: Remove brControl object
and update API parameter names & annotations.
* src/lxc/lxc_driver.c, src/network/bridge_driver.c,
src/uml/uml_conf.h, src/uml/uml_conf.c, src/uml/uml_driver.c,
src/qemu/qemu_command.c, src/qemu/qemu_conf.h,
src/qemu/qemu_driver.c: Remove reference to 'brControl' object
This patch is a fix for:
https://bugzilla.redhat.com/show_bug.cgi?id=743176
which was discovered by Dan Berrange while making bandwidth
configuration work for LXC guests.
Background: Although virtportprofile data from a network portgroup is
only applicable for direct mode interfaces, the code that copies
bandwidth data from the portgroup was also only being executed in the
case of direct mode interfaces. The result was that interfaces using
traditional virtual networks (forward mode='nat|route|none'), and
those using a host bridge for forwarding, would not pick up bandwidth
data from a portgroup defined in the network.
This patch moves that code outside the conditional, so that bandwidth
information is *alway* copied from the appropriate portgroup (unless
the <interface> definition itself already has bandwidth information,
which would take precedence over what's in the portgroup anyway).
Code altered so that it is consistent with the associated comment. The
'autoconf' variable is forced to zero.
Signed-off-by: Neil Wilson <neil@brightbox.co.uk>
In some cases the caller of virPidFileRead might like extra checks
to determine whether the pid just read is really the one they are
expecting. This adds virPidFileReadIfAlive which will check whether
the pid is still alive with kill(0, -1), and (on linux only) will
look at /proc/$PID/path
* libvirt_private.syms, util/virpidfile.c, util/virpidfile.h: Add
virPidFileReadIfValid and virPidFileReadPathIfValid
* network/bridge_driver.c: Use new APIs to check PID validity
The functions for manipulating pidfiles are in util/util.{c,h}.
We will shortly be adding some further pidfile related functions.
To avoid further growing util.c, this moves the pidfile related
functions into a dedicated virpidfile.{c,h}. The functions are
also all renamed to have 'virPidFile' as their name prefix
* util/util.h, util/util.c: Remove all pidfile code
* util/virpidfile.c, util/virpidfile.h: Add new APIs for pidfile
handling.
* lxc/lxc_controller.c, lxc/lxc_driver.c, network/bridge_driver.c,
qemu/qemu_process.c: Add virpidfile.h include and adapt for API
renames
This addresses https://bugzilla.redhat.com/show_bug.cgi?id=713728
When "defining" a new network (or one that exists but isn't currently
active) the new definition is stored in network->def, but for a
network that already exists and is active, the new definition is
stored in network->newDef, and then moved over to network->def as soon
as the network is destroyed.
However, the code that writes the dhcp and dns hosts files used by
dnsmasq was always using network->def for its information, even when
the new data was actually in network->newDef, so the hosts files
always lagged one edit behind the definition.
This patch changes the code to keep the pointer to the new definition
after it's been assigned into the network, and use it directly
(regardless of whether it's stored in network->newDef or network->def)
to construct the hosts files.
Coverity complained that 395 out of 409 virAsprintf calls are
checked, and therefore assumed that the remaining cases are bugs
waiting to happen. But in each of these cases, a failed virAsprintf
will properly set the target string to NULL, and pass on that
failure to the caller, without wasting efforts to check the call.
Adding the ignore_value silences Coverity.
* src/conf/domain_audit.c (virDomainAuditGetRdev): Ignore
virAsprintf return value, when it behaves like we need.
* src/network/bridge_driver.c (networkDnsmasqLeaseFileNameDefault)
(networkRadvdConfigFileName, networkBridgeDummyNicName)
(networkRadvdPidfileBasename): Likewise.
* src/util/storage_file.c (absolutePathFromBaseFile): Likewise.
* src/openvz/openvz_driver.c (openvzGenerateContainerVethName):
Likewise.
* src/util/command.c (virCommandTranslateStatus): Likewise.
This is in response to:
https://bugzilla.redhat.com/show_bug.cgi?id=723862
which points out that a guest on an "isolated" network could
potentially exploit the DNS forwarding provided by dnsmasq to create a
communication channel to the outside.
This patch eliminates that possibility by adding the "--no-resolv"
argument to the dnsmasq commandline, which tells dnsmasq to not
forward on any requests that it can't resolve itself (by looking at
its own static hosts files and runtime list of dhcp clients), but to
instead return a failure for those requests.
This shouldn't cause any undesirable change from current
behavior, even in the case where a guest is currently configured with
multiple interfaces, one of them being connected to an isolated
network, and another to a network that does have connectivity to the
outside. If the isolated network's DNS server is queried for a name
it doesn't know, it will return "Refused" rather than "Unknown", which
indicates to the guest that it should query other servers, so it then
queries the connected DNS server, and gets the desired response.
Every DomainNetDef has a bandwidth, as does every portgroup.
Whenever a DomainNetDef of type NETWORK is about to be used, a call is
made to networkAllocateActualDevice(). This function chooses the "best"
bandwidth object and places it in the DomainActualNetDef.
From that point on, whenever some code needs to use the bandwidth data
for the interface, it's retrieved with virDomainNetGetActualBandwidth(),
which will always return the "best" info as determined in the
previous step.
Although most functions in libvirt return 0 on success and < 0 on
failure, there are a few functions lingering around that return errno
(a positive value) on failure, and sometimes code calling those
functions incorrectly assumes the <0 standard. I noticed one of these
the other day when auditing networkStartDhcpDaemon after Guido Gunther
found a place where success was improperly returned on failure (that
patch has been acked and is pending a push). The problem was that it
expected the return value from virFileReadPid to be < 0 on failure,
but it was actually positive (it was also neglected to set the return
code in this case, similar to the bug found by Guido).
This all led to the fact that *all* of the virFile*Pid functions in
util.c are returning errno on failure. This patch remedies that
problem by changing them all to return -errno on failure, and makes
any necessary changes to callers of the functions. (In the meantime, I
also properly set the return code on failure of virFileReadPid in
networkStartDhcpDaemon).
The new listenNetwork attribute needs to learn an IP address based on a
named network. This patch provides a function networkGetNetworkAddress
which provides that.
Some networks have an IP address explicitly in their configuration
(ie, those with a forward type of "none", "route", or "nat"). For
those, we can just return the IP address from the config.
The rest will have a physical device associated with them (either via
<bridge name='...'/>, <forward ... dev='...'/>, or possibly via a pool
of interfaces inside the network's <forward> element) and we will need
to ask the kernel for a current IP address of that device (via the
newly added ifaceGetIPAddress)
If networkGetNetworkAddress encounters an error while trying to learn
the address for a network, it will return -1. In the case that libvirt
has been compiled without the network driver, the call is a macro
which reduces to -2. This allows differentiating between a failure of
the network driver, and its complete absence.
The network driver needs to assign physical devices for use by modes
that use macvtap, keeping track of which physical devices are in use
(and how many instances, when the devices can be shared). Three calls
are added:
networkAllocateActualDevice - finds a physical device for use by the
domain, and sets up the virDomainActualNetDef accordingly.
networkNotifyActualDevice - assumes that the domain was already
running, but libvirtd was restarted, and needs to be notified by each
already-running domain about what interfaces they are using.
networkReleaseActualDevice - decrements the usage count of the
allocated physical device, and frees the virDomainActualNetDef to
avoid later accidentally using the device.
bridge_driver.[hc] - the new APIs. When WITH_NETWORK is false, these
functions are all #defined to be "0" in the .h file (effectively
becoming a NOP) to prevent link errors.
qemu_(command|driver|hotplug|process).c - add calls to the above APIs
in the appropriate places.
tests/Makefile.am - we need to include libvirt_driver_network.la
whenever libvirt_driver_qemu.la is linked, to avoid unreferenced
symbols (in functions that are never called by the test
programs...)
Previously all networks were composed of bridge devices created and
managed by libvirt, and the same operations needed to be done for all
of them when they were started and stopped (create and start the
bridge device, configure its MAC address and IP address, add iptables
rules). The new network types are (for now at least) managed outside
of libvirt, and the network object is used only to contain information
about the network, which is then used as each individual guest
connects itself.
This means that when starting/stopping one of these new networks, we
really want to do nothing, aside from marking the network as
active/inactive.
This has been setup as toplevel Start/Shutdown functions that do the
small bit of common stuff, then have a switch statement to execute
network type-specific start/shutdown code, then do a bit more common
code. The type-specific functions called for the new host bridge and
macvtap based types are currently empty.
In the future these functions may actually do something, and we will
surely add more functions that are similarly patterned. Once
everything has settled, we can make a table of "sub-driver" function
pointers for each network type, and store a pointer to that table in
the network object, then we can replace the switch statements with
calls to functions in the table.
The final step in this will be to add a new table (and corresponding
new functions) for new network types as they are added.
The network XML is updated in the following ways:
1) The <forward> element can now contain a list of forward interfaces:
<forward .... >
<interface dev='eth10'/>
<interface dev='eth11'/>
<interface dev='eth12'/>
<interface dev='eth13'/>
</forward>
The first of these takes the place of the dev attribute that is
normally in <forward> - when defining a network you can specify
either one, and on output both will be present. If you specify
both on input, they must match.
2) In addition to forward modes of 'nat' and 'route', these new modes
are supported:
private, passthrough, vepa - when this network is referenced by a
domain's interface, it will have the same effect as if the
interface had been defined as type='direct', e.g.:
<interface type='direct'>
<source mode='${mode}' dev='${dev}>
...
</interface>
where ${mode} is one of the three new modes, and ${dev} is an interface
selected from the list given in <forward>.
bridge - if a <forward> dev (or multiple devs) is defined, and
forward mode is 'bridge' this is just like the modes 'private',
'passthrough', and 'vepa' above. If there is no forward dev
specified but a bridge name is given (e.g. "<bridge
name='br0'/>"), then guest interfaces using this network will use
libvirt's "host bridge" mode, equivalent to this:
<interface type='bridge'>
<source bridge='${bridge-name}'/>
...
</interface>
3) A network can have multiple <portgroup> elements, which may be
selected by the guest interface definition (by adding
"portgroup='${name}'" in the <source> element along with the
network name). Currently a portgroup can only contain a
virtportprofile, but the intent is that other configuration items
may be put there int the future (e.g. bandwidth config). When
building a guest's interface, if the <interface> XML itself has no
virtportprofile, and if the requested network has a portgroup with
a name matching the name given in the <interface> (or if one of the
network's portgroups is marked with the "default='yes'" attribute),
the virtportprofile from that portgroup will be used by the
interface.
4) A network can have a virtportprofile defined at the top level,
which will be used by a guest interface when connecting in one of
the 'direct' modes if the guest interface XML itself hasn't
specified any virtportprofile, and if there are also no matching
portgroups on the network.
Some callers expected virFileMakePath to set errno, some expected
it to return an errno value. Unify this to return 0 on success and
-1 on error. Set errno to report detailed error information.
Also optimize virFileMakePath if stat fails with an errno different
from ENOENT.
networkSaveDnsmasqHostsfile was added in 8fa9c22142 (Apr 2010).
It has a force flag. If the dnsmasq hostsfile already exists force
needs to be true to overwrite it. networkBuildDnsmasqArgv sets force
to false, networkDefine sets it to true. This results in the
hostsfile being written only in networkDefine in the common case.
If no error occurred networkSaveDnsmasqHostsfile returns true and
networkBuildDnsmasqArgv adds the --dhcp-hostsfile to the dnsmasq
command line.
networkSaveDnsmasqHostsfile was changed in 89ae9849f7 (24 Jun 2011)
to return a new dnsmasqContext instead of reusing one. This change broke
the logic of the force flag as now networkSaveDnsmasqHostsfile returns
NULL on error, but the early return -- if force was not set and the
hostsfile exists -- returns 0. This turned the early return in an error
case and networkBuildDnsmasqArgv didn't add the --dhcp-hostsfile option
anymore if the hostsfile already exists. It did because networkDefine
created the hostsfile already.
Then 9d4e2845d4 fixed the return 0 case in networkSaveDnsmasqHostsfile
but didn't apply the force option correctly to the new addnhosts file.
Now force doesn't control an early return anymore, but influences the
handling of the hostsfile context creation and dnsmasqSave is always
called now. This commit also added test cases that reveal several
problems. First, the tests now calls functions that try to write the
dnsmasq config files to disk. If someone runs this tests as root this
might overwrite actively used dnsmasq config files, this is a no-go. Also
the tests depend on configure --localstatedir, this needs to be fixed as
well, because it makes the tests fail when localstatedir is different
from /var.
This patch does several things to fix this:
1) Move dnsmasqContext creation and saving out of networkBuildDnsmasqArgv
to the caller to separate the command line generation from the config
file writing. This makes the command line generation testable without the
risk of interfering with system files, because the tests just don't call
dnsmasqSave.
2) This refactoring of networkSaveDnsmasqHostsfile makes the force flag
useless as the saving happens somewhere else now. This fixes the wrong
usage of the force flag in combination with then newly added addnhosts
file by removing the force flag.
3) Adapt the wrong test cases to the correct behavior, by adding the
missing --dhcp-hostsfile option. Both affected tests contain DHCP host
elements but missed the necessary --dhcp-hostsfile option.
4) Rename networkSaveDnsmasqHostsfile to networkBuildDnsmasqHostsfile,
because it doesn't save the dnsmasqContext anymore.
5) Move all directory creations in dnsmasq context handling code from
the *New functions to dnsmasqSave to avoid directory creations in system
paths in the test cases.
6) Now that networkBuildDnsmasqArgv doesn't create the dnsmasqContext
anymore the test case can create one with the localstatedir that is
expected by the tests instead of the configure --localstatedir given one.
If a domain name is defined for a network, add the --expand-hosts
option to the dnsmasq commandline. This results in the domain being
added to any hostname that is defined in a dns <host> element and
contains no '.' characters (i.e. it is an "unqualified"
hostname). Since PTR records are automatically created for any name
defined in <host>, the result of a PTR request will change from the
unqualified name to the qualified name.
This also has the same effect on any hostnames that dnsmasq reads
from the host's /etc/hosts file.
(In the case of guest hostnames that were learned by dnsmasq via DHCP
requests, they were already getting the domain name added on, even
without --expand-hosts).
Convert networkDnsmasqLeaseFileName to a replaceable function pointer
that allow the testsuite to use a version of that function that is not
depending on configure --localstatedir.
This fixes 5 of 6 test failures, when configure --localstatedir isn't
set to /var.
This commit introduces names definition for the DNS hosts file using
the following syntax:
<dns>
<host ip="192.168.1.1">
<name>alias1</name>
<name>alias2</name>
</host>
</dns>
Some of the improvements and fixes were done by Laine Stump so
I'm putting him into the SOB clause again ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
The dnsmasq commandline was being built as a part of running
dnsmasq. This patch puts the commandline build into a separate
function (and exports it as a private API) making it possible to build
a dnsmasq commandline without executing it, so that we can write a
test program to verify that the proper commandlines are being created.
Signed-off-by: Michal Novotny <minovotn@redhat.com>
This commit introduces the <dns> element and <txt> record for the
virtual DNS network. The DNS TXT record can be defined using following
syntax in the network XML file:
<dns>
<txt name="example" value="example value" />
</dns>
Also, the Relax-NG scheme has been altered to allow the texts without
spaces only for the name element and some nitpicks about memory
free'ing have been fixed by Laine so therefore I'm adding Laine to the
SOB clause ;-)
Signed-off-by: Michal Novotny <minovotn@redhat.com>
Signed-off-by: Laine Stump <laine@laine.org>
Since we virEventRegisterDefaultImpl is now a public API, callers need
a way to invoke the default registered Handle and Timeout functions. We
already have general functions for these internally, so promote
them to the public API.
v2:
Actually add APIs to libvirt.h
Change all the driver struct initializers to use the
C99 style, leaving out unused fields. This will make
it possible to add new APIs without changing every
driver. eg change:
qemudDomainResume, /* domainResume */
qemudDomainShutdown, /* domainShutdown */
NULL, /* domainReboot */
qemudDomainDestroy, /* domainDestroy */
to
.domainResume = qemudDomainResume,
.domainShutdown = qemudDomainShutdown,
.domainDestroy = qemudDomainDestroy,
And get rid of any existing C99 style initializersr which
set NULL, eg change
.listPools = vboxStorageListPools,
.numOfDefinedPools = NULL,
.listDefinedPools = NULL,
.findPoolSources = NULL,
.poolLookupByName = vboxStoragePoolLookupByName,
to
.listPools = vboxStorageListPools,
.poolLookupByName = vboxStoragePoolLookupByName,
We were 31/73 on whether to translate; since less than 50% translated
and since VIR_INFO is less than VIR_WARN which also doesn't translate,
this makes sense.
* cfg.mk (sc_prohibit_gettext_markup): Add VIR_INFO, since it
falls between WARN and DEBUG.
* daemon/libvirtd.c (qemudDispatchSignalEvent, remoteCheckAccess)
(qemudDispatchServer): Adjust offenders.
* daemon/remote.c (remoteDispatchAuthPolkit): Likewise.
* src/network/bridge_driver.c (networkReloadIptablesRules)
(networkStartNetworkDaemon, networkShutdownNetworkDaemon)
(networkCreate, networkDefine, networkUndefine): Likewise.
* src/qemu/qemu_driver.c (qemudDomainDefine)
(qemudDomainUndefine): Likewise.
* src/storage/storage_driver.c (storagePoolCreate)
(storagePoolDefine, storagePoolUndefine, storagePoolStart)
(storagePoolDestroy, storagePoolDelete, storageVolumeCreateXML)
(storageVolumeCreateXMLFrom, storageVolumeDelete): Likewise.
* src/util/bridge.c (brProbeVnetHdr): Likewise.
* po/POTFILES.in: Drop src/util/bridge.c.
These VIR_XXXX0 APIs make us confused, use the non-0-suffix APIs instead.
How do these coversions works? The magic is using the gcc extension of ##.
When __VA_ARGS__ is empty, "##" will swallow the "," in "fmt," to
avoid compile error.
example: origin after CPP
high_level_api("%d", a_int) low_level_api("%d", a_int)
high_level_api("a string") low_level_api("a string")
About 400 conversions.
8 special conversions:
VIR_XXXX0("") -> VIR_XXXX("msg") (avoid empty format) 2 conversions
VIR_XXXX0(string_literal_with_%) -> VIR_XXXX(%->%%) 0 conversions
VIR_XXXX0(non_string_literal) -> VIR_XXXX("%s", non_string_literal)
(for security) 6 conversions
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
This matches the public API and helps to get rid of some special
case code in the remote generator.
Rename driver API functions and XDR protocol structs.
No functional change included outside of the remote generator.
We already have virAsprintf, so picking a similar name helps for
seeing a similar purpose. Furthermore, the prefix V before printf
generally implies 'va_list', even though this variant was '...', and
the old name got in the way of adding a new va_list version.
global rename performed with:
$ git grep -l virBufferVSprintf \
| xargs -L1 sed -i 's/virBufferVSprintf/virBufferAsprintf/g'
then revert the changes in ChangeLog-old.
This patch addresses:
https://bugzilla.redhat.com/show_bug.cgi?id=694382
In order to give each libvirt-created bridge a fixed MAC address,
commit 5754dbd56d, added code to create
a dummy tap device with guaranteed lowest MAC address and attach it to
the bridge. This tap device was given the name "${bridgename}-nic".
However, an interface device name must be IFNAMSIZ (15) characters or
less, so a valid ${bridgename} such as "verylongname123" (15
characters) would lead to an invalid tap device name
("verylongname123-nic" - 19 characters), and that in turn led to a
failure to bring up the network.
The solution is to shorten the part of the original name used to
generate the tap device name. However, simply truncating it is
insufficient, because the last few characters of an interface name are
often a number used to indicate one of a list of several similar
devices (for example, "verylongname123", "verylongname124", etc) and
simple truncation would lead to duplicate names (eg "verlongnam-nic"
and "verylongnam-nic"). So instead we take the first 8 characters of
$bridgename ("verylong" in the example), add on the final 3 bytes
("123"), then add "-nic" (so "verylong123-nic"). Not pretty, but it
is much more likely to generate a unique name, and is reproducible
(unlike, say, a random number).
This fixes: https://bugzilla.redhat.com/show_bug.cgi?id=696660
While starting a network, if brSetForwardDelay() fails, we go to err1
where we want to access macTapIfName variable which was just
VIR_FREE'd a few lines above. Instead, keep macTapIfName until we are
certain of success.
Currently libvirt's default logging is limited and it is difficult to
determine what was happening when a proglem occurred (especially on a
machines where one don't know the detail.) This patch helps to do that
by making additional logging available for the following events:
creating/defining/undefining domains
creating/defining/undefining/starting/stopping networks
creating/defining/undefining/starting/stopping storage pools
creating/defining/undefining/starting/stopping storage volumes.
* AUTHORS: add Naoya Horiguchi
* src/network/bridge_driver.c src/qemu/qemu_driver.c
src/storage/storage_driver.c: provide more VIR_INFO logging
This simplifies several callers that were repeating checks already
guaranteed by util.c, and makes other callers more robust to now
reject directories. remote_driver.c was over-strict - access(,R_OK)
is only needed to execute a script file; a binary only needs
access(,X_OK) (besides, it's unusual to see a file with x but not
r permissions, whether script or binary).
* cfg.mk (sc_prohibit_access_xok): New syntax-check rule.
(exclude_file_name_regexp--sc_prohibit_access_xok): Exempt one use.
* src/network/bridge_driver.c (networkStartRadvd): Fix offenders.
* src/qemu/qemu_capabilities.c (qemuCapsProbeMachineTypes)
(qemuCapsInitGuest, qemuCapsInit, qemuCapsExtractVersionInfo):
Likewise.
* src/remote/remote_driver.c (remoteFindDaemonPath): Likewise.
* src/uml/uml_driver.c (umlStartVMDaemon): Likewise.
* src/util/hooks.c (virHookCheck): Likewise.
This is detailed in:
https://bugzilla.redhat.com/show_bug.cgi?id=688957
Since radvd is executed by daemonizing it, the attempt to exec the
radvd binary doesn't happen until after libvirtd has already received
an exit code from the intermediate forked process, so no error is
detected or logged by __virExec().
We can't require radvd as a prerequisite for the libvirt package (many
installations don't use IPv6, so they don't need it), so instead we
add in a check to verify there is an executable radvd binary prior to
trying to exec it.
Normally dnsmasq will send a default route (the address of the host in
the network definition) to any client requesting an address via
DHCP. On an isolated network this makes no sense, as we have iptables
to prevent any traffic going out via that interface, so anything sent
that way would be dropped anyway.
This extra/unusable default route becomes problematic if you have
setup a guest with multiple network interfaces, with one connected to
an isolated network and another that provides connectivity to the
outside (example - one interface directly connecting to a physical
interface via macvtap, with a second connected to an isolated network
so that the host and guest can communicate (macvtap doesn't support
guest<->host communication without an external switch that supports
vepa, or reflecting all traffic back)). In this case, if the guest
chooses the default route of the isolated network, the guest will not
be able to get network traffic beyond the host.
To prevent dnsmasq from sending a default route, you can tell it to
send 0 bytes of data for the default route option (option number 3)
with --dhcp-option=3 (normally the data to send for the option would
follow the option number; no extra data means "don't send this option").
I have checked on RHEL5 (a good representative of the oldest supported
libvirt platforms) and its version of dnsmasq (2.45) does support
--dhcp-option, so this shouldn't create any compatibility problems.
By default, all dnsmasq processes share the same leases file. libvirt
also uses the --dhcp-lease-max option to control the maximum number of
leases allowed. The problem is that libvirt puts in a number equal to
the number of addresses in the range for the one network handled by a
single instance of dnsmasq, but dnsmasq checks the total number of
leases in the file (which could potentially contain many more).
The solution is to tell each instance of dnsmasq to create and use its
own leases file. (/var/lib/libvirt/network/<net-name>.leases).
This file is created by dnsmasq when it starts, but not deleted when
it exists. This is fine when the network is just being stopped, but if
the leases file was left around when a network was undefined, we could
end up with an ever-increasing number of dead files - instead, we
explicitly unlink the leases file when a network is undefined.
Note that Ubuntu carries a patch against an older version of libvirt for this:
hhttps://bugs.launchpad.net/ubuntu/+source/libvirt/+bug/713071
ttp://bazaar.launchpad.net/~serge-hallyn/ubuntu/maverick/libvirt/bugall/revision/109
I was certain I'd also seen discussion of this on libvir-list or
libvirt-users, but couldn't find it.
This fixes a regression introduced in commit ad48df, and reported on
the libvirt-users list:
https://www.redhat.com/archives/libvirt-users/2011-March/msg00018.html
The problem in that commit was that we began searching a list of ip
address definitions (rather than just having one) to look for a dhcp
range or static host; when we didn't find any, our pointer (ipdef) was
left at NULL, and when ipdef was NULL, we returned without starting up
dnsmasq.
Previously dnsmasq was started even without any dhcp ranges or static
entries, because it's still useful for DNS services.
Another problem I noticed while investigating was that, if there are
IPv6 addresses, but no IPv4 addresses of any kind, we would jump out
at an ever higher level in the call chain.
This patch does the following:
1) networkBuildDnsmasqArgv() = all uses of ipdef are protected from
NULL dereference. (this patch doesn't change indentation, to make
review easier. The next patch will change just the
indentation). ipdef is intended to point to the first IPv4 address
with DHCP info (or the first IPv4 address if none of them have any
dhcp info).
2) networkStartDhcpDaemon() = if the loop looking for an ipdef with
DHCP info comes up empty, we then grab the first IPv4 def from the
list. Also, instead of returning if there are no IPv4 defs, we just
return if there are no IP defs at all (either v4 or v6). This way a
network that is IPv6-only will still get dnsmasq listening for DNS
queries.
3) in networkStartNetworkDaemon() - we will startup dhcp not just if there
are any IPv4 addresses, but also if there are any IPv6 addresses.
This fixes https://bugzilla.redhat.com/show_bug.cgi?id=609463
The problem was that, since a bridge always acquires the MAC address
of the connected interface with the numerically lowest MAC, as guests
are started and stopped, it was possible for the MAC address to change
over time, and this change in the network was being detected by
Windows 7 (it sees the MAC of the default route change), so on each
reboot it would bring up a dialog box asking about this "new network".
The solution is to create a dummy tap interface with a MAC guaranteed
to be lower than any guest interface's MAC, and attach that tap to the
bridge as soon as it's created. Since all guest MAC addresses start
with 0xFE, we can just generate a MAC with the standard "0x52, 0x54,
0" prefix, and it's guaranteed to always win (physical interfaces are
never connected to these bridges, so we don't need to worry about
competing numerically with them).
Note that the dummy tap is never set to IFF_UP state - that's not
necessary in order for the bridge to take its MAC, and not setting it
to UP eliminates the clutter of having an (eg) "virbr0-nic" displayed
in the output of the ifconfig command.
I chose to not auto-generate the MAC address in the network XML
parser, as there are likely to be consumers of that API that don't
need or want to have a MAC address associated with the
bridge.
Instead, in bridge_driver.c when the network is being defined, if
there is no MAC, one is generated. To account for virtual network
configs that already exist when upgrading from an older version of
libvirt, I've added a %post script to the specfile that searches for
all network definitions in both the config directory
(/etc/libvirt/qemu/networks) and the state directory
(/var/lib/libvirt/network) that are missing a mac address, generates a
random address, and adds it to the config (and a matching address to
the state file, if there is one).
docs/formatnetwork.html.in: document <mac address.../>
docs/schemas/network.rng: add nac address to schema
libvirt.spec.in: %post script to update existing networks
src/conf/network_conf.[ch]: parse and format <mac address.../>
src/libvirt_private.syms: export a couple private symbols we need
src/network/bridge_driver.c:
auto-generate mac address when needed,
create dummy interface if mac address is present.
tests/networkxml2xmlin/isolated-network.xml
tests/networkxml2xmlin/routed-network.xml
tests/networkxml2xmlout/isolated-network.xml
tests/networkxml2xmlout/routed-network.xml: add mac address to some tests
I added a host definition to a network definition:
<network>
<name>Lokal</name>
<uuid>2074f379-b82c-423f-9ada-305d8088daaa</uuid>
<bridge name='virbr1' stp='on' delay='0' />
<ip address='192.168.180.1' netmask='255.255.255.0'>
<dhcp>
<range start='192.168.180.128' end='192.168.180.254' />
<host mac='23:74:00:03:42:02' name='somevm' ip='192.168.180.10' />
</dhcp>
</ip>
</network>
But due to the wrong if-statement the argument --dhcp-hostsfile doesn't get
added to the dnsmasq command. The patch below fixes it for me.
Running an instance of the router advertisement daemon (radvd) allows
guests using the virtual network to automatically acquire an IPv6
address and default route. Note that acquiring an address only works
for networks with a prefix length of exactly 64 - radvd is still run
in other circumstances, and still advertises routes, but autoconf will
not work because it requires exactly 64 bits of address info from the
network prefix.
This patch avoids a race condition with the pidfile by manually
daemonizing radvd rather than allowing it to daemonize itself, then
creating our own pidfile (in addition to radvd's own file, which is
unnecessary, but there is no way to tell radvd to not create it). This
is accomplished by exec'ing it with "--debug 1" in the commandline,
and using virCommand's features to fork, create a pidfile, and detach
from the newly forked process.
At this point everything is already in place to make IPv6 happen, we just
need to add a few rules, remove some checks for IPv4-only, and document
the changes to the XML on the website.
All of the iptables functions eventually call down to a single
bottom-level function, and fortunately, ip6tables syntax (for all the
args that we use) is identical to iptables format (except the
addresses), so all we need to do is:
1) Get an address family down to the lowest level function in each
case, either implied through an address, or explicitly when no
address is in the parameter list, and
2) At the lowest level, just decide whether to call "iptables" or
"ip6tables" based on the family.
The location of the ip6tables binary is determined at build time by
autoconf. If a particular target system happens to not have ip6tables
installed, any attempts to run it will generate an error, but that
won't happen unless someone tries to define an IPv6 address for a
network. This is identical behavior to IPv4 addresses and iptables.
This patch reorganizes the code in bridge_driver.c to account for the
concept of a single network with multiple IP addresses, without adding
in the extra variable of IPv6. A small bit of code has been
temporarily added that checks all given addresses to verify they are
IPv4 - this will be removed when full IPv6 support is turned on.
This commit adds support for IPv6 parsing and formatting to the
virtual network XML parser, including moving around data definitions
to allow for multiple <ip> elements on a single network, but only
changes the consumers of this API to accommodate for the changes in
API/structure, not to add any actual IPv6 functionality. That will
come in a later patch - this patch attempts to maintain the same final
functionality in both drivers that use the network XML parser - vbox
and "bridge" (the Linux bridge-based driver used by the qemu
hypervisor driver).
* src/libvirt_private.syms: Add new private API functions.
* src/conf/network_conf.[ch]: Change C data structure and
parsing/formatting.
* src/network/bridge_driver.c: Update to use new parser/formatter.
* src/vbox/vbox_tmpl.c: update to use new parser/formatter
* docs/schemas/network.rng: changes to the schema -
* there can now be more than one <ip> element.
* ip address is now an ip-addr (ipv4 or ipv6) rather than ipv4-addr
* new optional "prefix" attribute that can be used in place of "netmask"
* new optional "family" attribute - "ipv4" or "ipv6"
(will default to ipv4)
* define data types for the above
* tests/networkxml2xml(in|out)/nat-network.xml: add multiple <ip> elements
(including IPv6) to a single network definition to verify they are being
correctly parsed and formatted.
brSetInetAddress can only set a single IP address on the bridge, and
uses a method (ioctl(SIOCSETIFADDR)) that only works for IPv4. Replace
it and brSetInetNetmask with a single function that uses the external
"ip addr add" command to add an address/prefix to the interface - this
supports IPv6, and allows adding multiple addresses to the interface.
Although it isn't currently used in the code, we also add a
brDelInetAddress for completeness' sake.
Also, while we're modifying bridge.c, we change brSetForwardDelay and
brSetEnableSTP to use the new virCommand API rather than the
deprecated virRun, and also log an error message in bridge_driver.c if
either of those fail (previously the failure would be completely
silent).
IPv6 will use prefix exclusively, and IPv4 will also optionally be
able to use it, and the iptables functions really need a prefix
anyway, so use the new virNetworkDefPrefix() function to send prefixes
into iptables functions instead of netmasks.
Also, in a couple places where a netmask is actually needed, use the
new private API function for it rather than getting it directly. This
will allow for cases where no netmask or prefix is specified (it
returns the default for the current class of network.)
Some functions in this file were returning 1 on success and 0 on
failure, and others were returning 0 on success and -1 on
failure. Switch them all to return the libvirt-preferred 0/-1.
The functions in iptables.c all return -1 on failure, but all their
callers (which all happen to be in bridge_driver.c) assume that they
are returning an errno, and the logging is done accordingly. This
patch fixes all the error checking and logging to assume < 0 is an
error, and nothing else.
While not technically a double free (since VIR_FREE NULLs the
pointer), this is unnecessary extra code.
This crept in when the function was converted from virRun to virCommand.
The AUTHORS file has also been updated.
This is pretty straightforward - even though dnsmasq gets daemonized
and uses a pid file, those things are both handled by the dnsmasq
binary itself. And libvirt doesn't need any of the output of the
dnsmasq command either, so we just setup the args and call
virRun(). Mainly it was just a (mostly) mechanical job of replacing
the APPEND_ARG() macro (and some other *printfs()) with
virCommandAddArg*().
This patch adds a mode_t parameter to virFileWriteStr().
If mode is different from 0, virFileWriteStr() will try
to create the file if it doesn't exist.
* src/util/util.h (virFileWriteStr): Alter signature.
* src/util/util.c (virFileWriteStr): Allow file creation.
* src/network/bridge_driver.c (networkEnableIpForwarding)
(networkDisableIPV6): Adjust clients.
* src/node_device/node_device_driver.c
(nodeDeviceVportCreateDelete): Likewise.
* src/util/cgroup.c (virCgroupSetValueStr): Likewise.
* src/util/pci.c (pciBindDeviceToStub, pciUnBindDeviceFromStub):
Likewise.
During virtual network startup, the iptables rule that allows tftp
traffic is only added if network->def->tftproot is non-empty, but when
the virtual network is destroyed, we had been unconditionally trying
to delete the rule. This was harmless, except that it created a bogus
error message.
This patch conditionalizes the delete command in the same manner that
the insert command is already conditionalized.
When failing to start a virtual network, we have to cleanup,
tearing down any iptables rules. If the iptables rules were
not present yet though, this raises an error, which squashes
the original error we were handling.
* src/network/bridge_driver.c: When failing to start a virtual
network, don't squash the original error in cleanup
The network address was being set to 192.168.122.0 instead
of 192.168.122.0/24. Fix this by removing the unneccessary
'network' field from virNetworkDef and just pass the
network address and netmask into the iptables APIs directly.
* src/conf/network_conf.h, src/conf/network_conf.c: Remove
the 'network' field from virNEtworkDef.
* src/network/bridge_driver.c: Update for iptables API changes
* src/util/iptables.c, src/util/iptables.h: Require the
network address + netmask pair to be passed in
Instead of storing the IP address string in virNetwork related
structs, store the parsed virSocketAddr. This will make it
easier to add IPv6 support in the future, by letting driver
code directly check what address family is present
* src/conf/network_conf.c, src/conf/network_conf.h,
src/network/bridge_driver.c: Convert to use virSocketAddr
in virNetwork, instead of char *.
* src/util/bridge.c, src/util/bridge.h,
src/util/dnsmasq.c, src/util/dnsmasq.h,
src/util/iptables.c, src/util/iptables.h: Convert to
take a virSocketAddr instead of char * for any IP
address parameters
* src/util/network.h: Add macros to determine if an address
is set, and what address family is set.
The virSocketParse method was not doing any error reporting
which meant the true cause of the problem was lost. Remove
all error reporting from callers, and push it into virSocketParse
* src/util/network.c: Add error reporting to virSocketParse
* src/conf/domain_conf.c, src/conf/network_conf.c,
src/network/bridge_driver.c: Remove error reporting in
callers of virSocketParse
The virSocketParseAddr function was accepting any AF_* constant
and using that to set the ai_flags field in struct addrinfo.
This is invalid, since address families must go in the ai_family
field of the struct.
* src/util/network.c: Fix handling of address family
* src/conf/network_conf.c, src/network/bridge_driver.c: Pass
AF_UNSPEC instead of relying on it being 0.
Some operations on socket addresses need to know the length of
the sockaddr struct for the particular address family. This
info was being discarded when passing around virSocketAddr
instances. Turn it from a union into a struct containing
union+socklen_t fields, so length is always kept around.
* src/util/network.h: Add socklen_t field to virSocketAddr
* src/util/network.c, src/network/bridge_driver.c,
src/conf/domain_conf.c: Update to take account of new
struct definition.
For static-only DHCP, i.e. with no <range> but at least one <host>
element within <dhcp> element, we have to add "--dhcp-range IP,static"
option to dnsmasq to actually enable the service. Without this option,
dnsmasq will not respond to DHCP requests.
--dhcp-no-override description from dnsmasq man page:
Disable re-use of the DHCP servername and filename fields as
extra option space. If it can, dnsmasq moves the boot server and
filename information (from dhcp-boot) out of their dedicated
fields into DHCP options. This make extra space available in the
DHCP packet for options but can, rarely, confuse old or broken
clients. This flag forces "simple and safe" behaviour to avoid
problems in such a case.
It seems some virtual network card ROMs are this old/buggy so let's add
--dhcp-no-override as a workaround for them. We don't use extra DHCP
options so this should be safe. The option was added in dnsmasq-2.41,
which becomes the minimum required version.
We add --dhcp-lease-max=xxx argument when network->def->nranges > 0 but
we only allocate space for in the opposite case :-) I guess we are lucky
enough to miscount somewhere else so that we actually allocate more
space than we need since no-one has hit this bug so far.
This patch attempts to take advantage of a newly added netfilter
module to correct for a problem with some guest DHCP client
implementations when used in conjunction with a DHCP server run on the
host systems with packet checksum offloading enabled.
The problem is that, when the guest uses a RAW socket to read the DHCP
response packets, the checksum hasn't yet been fixed by the IP stack,
so it is incorrect.
The fix implemented here is to add a rule to the POSTROUTING chain of
the mangle table in iptables that fixes up the checksum for packets on
the virtual network's bridge that are destined for the bootpc port (ie
"dhcpc", ie port 68) port on the guest.
Only very new versions of iptables will have this support (it will be
in the next upstream release), so a failure to add this rule only
results in a warning message. The iptables patch is here:
http://patchwork.ozlabs.org/patch/58525/
A corresponding kernel module patch is also required (the backend of
the iptables patch) and that will be in the next release of the
kernel.
IPtables will seek to preserve the source port unchanged when
doing masquerading, if possible. NFS has a pseudo-security
option where it checks for the source port <= 1023 before
allowing a mount request. If an admin has used this to make the
host OS trusted for mounts, the default iptables behaviour will
potentially allow NAT'd guests access too. This needs to be
stopped.
With this change, the iptables -t nat -L -n -v rules for the
default network will be
Chain POSTROUTING (policy ACCEPT 95 packets, 9163 bytes)
pkts bytes target prot opt in out source destination
14 840 MASQUERADE tcp -- * * 192.168.122.0/24 !192.168.122.0/24 masq ports: 1024-65535
75 5752 MASQUERADE udp -- * * 192.168.122.0/24 !192.168.122.0/24 masq ports: 1024-65535
0 0 MASQUERADE all -- * * 192.168.122.0/24 !192.168.122.0/24
* src/network/bridge_driver.c: Add masquerade rules for TCP
and UDP protocols
* src/util/iptables.c, src/util/iptables.c: Add source port
mappings for TCP & UDP protocols when masquerading.
add iptables rules to allow TFTP from the virtual network if <tftp>
element is defined in the network definition.
Fedora bz#580215
* src/network/bridge_driver.c: open UDP port 69 for TFTP traffic if
tftproot is defined
The network driver is not doing correct checking for
duplicate UUID/name values. This introduces a new method
virNetworkObjIsDuplicate, based on the previously
written virDomainObjIsDuplicate.
* src/conf/network_conf.c, src/conf/network_conf.c,
src/libvirt_private.syms: Add virNetworkObjIsDuplicate,
* src/network/bridge_driver.c: Call virNetworkObjIsDuplicate
for checking uniqueness of uuid/names
Fedora bug https://bugzilla.redhat.com/show_bug.cgi?id=235961
If using the default virtual network, an easy way to lose guest network
connectivity is to install libvirt inside the VM. The autostarted
default network inside the guest collides with host virtual network
routing. This is a long standing issue that has caused users quite a
bit of pain and confusion.
On network startup, parse /proc/net/route and compare the requested
IP+netmask against host routing destinations: if any matches are found,
refuse to start the network.
v2: Drop sscanf, fix a comment typo, comment that function could use
libnl instead of /proc
v3: Consider route netmask. Compare binary data rather than convert to
string.
v4: Return to using sscanf, drop inet functions in favor of virSocket,
parsing safety checks. Don't make parse failures fatal, in case
expected format changes.
v5: Try and continue if we receive unexpected. Delimit parsed lines to
prevent scanning past newline
Approximately 60 messages were marked. Since these diagnostics are
intended solely for developers and maintainers, encouraging translation
is deemed to be counterproductive:
http://thread.gmane.org/gmane.comp.emulators.libvirt/25050/focus=25052
Run this command:
git grep -l VIR_WARN|xargs perl -pi -e \
's/(VIR_WARN0?)\s*\(_\((".*?")\)/$1($2/'
use /var/lib/libvirt/dnsmasq since /var/lib/libvirt/network is
unreadable by the dnsmasq binary
* src/network/bridge_driver.c: update DNSMASQ_STATE_DIR
* src/Makefile.am: create it on make install
* libvirt.spec.in: take the new directory into account
This patch makes libvirtd start the dnsmasq daemon with a
--dhcp-hostsfile option instead of --dhcp-host options for each
'//ip/dhcp/host' entries defined in network xml file.
the dnsmasq host file is stored into /var/lib/libvirt/network
* src/network/bridge_driver.c: define the directory for the hostfiles
and save/delete them to be used by dnsmasq
The virConnectPtr is no longer required for error reporting since
that is recorded in a thread local. Remove use of virConnectPtr
from all APIs in network_conf.{h,c} and update all callers to
match
* src/lxc/lxc_container.c src/lxc/lxc_controller.c src/lxc/lxc_driver.c
src/network/bridge_driver.c src/qemu/qemu_driver.c
src/uml/uml_driver.c: virFileMakePath returns 0 for success, or the
value of errno on failure, so error checking should be to test
if non-zero, not if lower than 0
I noticed some debug messages are printed with an empty lines after
them. This patch removes these empty lines from all invocations of the
following macros:
VIR_DEBUG
VIR_DEBUG0
VIR_ERROR
VIR_ERROR0
VIR_INFO
VIR_WARN
VIR_WARN0
Signed-off-by: Jiri Denemark <jdenemar@redhat.com>
Long ago we tried to use Fedora's lokkit utility in order to register
our iptables rules so that 'service iptables restart' would
automatically load our rules.
There was one fatal flaw - if the user had configured iptables without
lokkit, then we would clobber that configuration by running lokkit.
We quickly disabled lokkit support, but never removed it. Let's do
that now.
The 'my virtual network stops working when I restart iptables' still
remains. For all the background on this saga, see:
https://bugzilla.redhat.com/227011
* src/util/iptables.c: remove lokkit support
* configure.in: remove --enable-lokkit
* libvirt.spec.in: remove the dirs used only for saving rules for lokkit
* src/Makefile.am: ditto
* src/libvirt_private.syms, src/network/bridge_driver.c,
src/util/iptables.h: remove references to iptablesSaveRules
This is the expected behaviour, I think - reloading libvirtd should
be a subset of restarting it.
Note, we reload the rules after we've determined which networks
are active (because we only add the rules for active networks)
and before we start autostart networks (to avoid re-adding the
rules).
* src/network/bridge_driver.c: reload iptables rules on startup
Currently, when we add iptables rules, we keep them on a list so that
we can easily reload them on e.g. 'service libvirtd reload'.
However, we don't save this list to disk, so if libvirtd is restarted
we lose the ability to reload the rules.
The fix is simple - just re-add the damn things on reload.
Note, we delete the rules before re-adding them, just like the current
behaviour of iptRulesReload().
* src/network/bridge_driver.c: re-add the iptables rules on reload.
Introduce a number of new APIs to expose some boolean properties
of objects, which cannot otherwise reliably determined, nor are
aspects of the XML configuration.
* virDomainIsActive: Checking virDomainGetID is not reliable
since it is not possible to distinguish between error condition
and inactive domain for ID of -1.
* virDomainIsPersistent: Check whether a persistent config exists
for the domain
* virNetworkIsActive: Check whether the network is active
* virNetworkIsPersistent: Check whether a persistent config exists
for the network
* virStoragePoolIsActive: Check whether the storage pool is active
* virStoragePoolIsPersistent: Check whether a persistent config exists
for the storage pool
* virInterfaceIsActive: Check whether the host interface is active
* virConnectIsSecure: whether the communication channel to the
hypervisor is secure
* virConnectIsEncrypted: whether any network based commnunication
channels are encrypted
NB, a channel can be secure, even if not encrypted, eg if it does
not involve the network, like a UNIX socket, or pipe.
* include/libvirt/libvirt.h.in: Define public API
* src/driver.h: Define internal driver API
* src/libvirt.c: Implement public API entry point
* src/libvirt_public.syms: Export API symbols
* src/esx/esx_driver.c, src/lxc/lxc_driver.c,
src/interface/netcf_driver.c, src/network/bridge_driver.c,
src/opennebula/one_driver.c, src/openvz/openvz_driver.c,
src/phyp/phyp_driver.c, src/qemu/qemu_driver.c,
src/remote/remote_driver.c, src/test/test_driver.c,
src/uml/uml_driver.c, src/vbox/vbox_tmpl.c,
src/xen/xen_driver.c: Stub out driver tables
* src/network/bridge_driver.c: when exec'ing dnsmaq, if there are
DHCP ranges defined, then compute and pass the --dhcp-lease-max
deriving the maximum number of leases
The LXC driver was mistakenly returning -1 for lxcStartup()
in scenarios that are not an error. This caused the libvirtd
to quit for unprivileged users. This fixes the return code
of LXC driver, and also adds a "name" field to the virStateDriver
struct and logging to make it easier to find these problems
in the future
* src/driver.h: Add a 'name' field to state driver to allow
easy identification during failures
* src/libvirt.c: Log name of failed driver for virStateInit
failures
* src/lxc/lxc_driver.c: Don't return a failure code for
lxcStartup() if LXC is not available on this host, simply
disable the driver.
* src/network/bridge_driver.c, src/node_device/node_device_devkit.c,
src/node_device/node_device_hal.c, src/opennebula/one_driver.c,
src/qemu/qemu_driver.c, src/remote/remote_driver.c,
src/secret/secret_driver.c, src/storage/storage_driver.c,
src/uml/uml_driver.c, src/xen/xen_driver.c: Fill in name
field in virStateDriver struct
Rename virDomainIsActive to virDomainObjIsActive, and
virInterfaceIsActive to virInterfaceObjIsActive and finally
virNetworkIsActive to virNetworkObjIsActive.
* src/conf/domain_conf.c, src/conf/domain_conf.h,
src/conf/interface_conf.h, src/conf/network_conf.c,
src/conf/network_conf.h, src/lxc/lxc_driver.c,
src/network/bridge_driver.c, src/opennebula/one_driver.c,
src/openvz/openvz_driver.c, src/qemu/qemu_driver.c,
src/test/test_driver.c, src/uml/uml_driver.c: Update for
renamed APIs.
Nearly all of the methods in src/util/util.h have error codes that
must be checked by the caller to correct detect & report failure.
Add ATTRIBUTE_RETURN_CHECK to ensure compile time validation of
this
* daemon/libvirtd.c: Add explicit check on return value of virAsprintf
* src/conf/domain_conf.c: Add missing check on virParseMacAddr return
value status & report error
* src/network/bridge_driver.c: Add missing OOM check on virAsprintf
and report error
* src/qemu/qemu_conf.c: Add missing check on virParseMacAddr return
value status & report error
* src/security/security_selinux.c: Remove call to virRandomInitialize
that's done in libvirt.c already
* src/storage/storage_backend_logical.c: Add check & log on virRun
return status
* src/util/util.c: Add missing checks on virAsprintf/Run status
* src/util/util.h: Annotate all methods with ATTRIBUTE_RETURN_CHECK
if they return an error status code
* src/vbox/vbox_tmpl.c: Add missing check on virParseMacAddr
* src/xen/xm_internal.c: Add missing checks on virAsprintf
* tests/qemuargv2xmltest.c: Remove bogus call to virRandomInitialize()
This patch adds an optional attribute to the <bootp> tag, that
allows to specify a TFTP server address other than the address of
the DHCP server itself.
This can be used to forward the BOOTP settings of the host down to the
guest. This is something that configurations such as Xen's default
network achieve naturally, but must be done manually for NAT.
* docs/formatnetwork.html.in: Document new attribute.
* docs/schemas/network.rng: Add it to schema.
* src/conf/network_conf.h: Add it to struct.
* src/conf/network_conf.c: Add it to parser and pretty printer.
* src/network/bridge_driver.c: Put it in the dnsmasq command line.
* tests/networkxml2xmlin/netboot-proxy-network.xml
tests/networkxml2xmlout/netboot-proxy-network.xml
tests/networkxml2xmltest.c: add new tests
Currently, libvirtd will start a dnsmasq process for the virtual
network, but (aside from killing the dnsmasq process and replacing it),
there's no way to define tftp boot options.
This change introduces the appropriate tags to the dhcp configuration:
<network>
<name>default</name>
<bridge name="virbr%d" />
<forward/>
<ip address="192.168.122.1" netmask="255.255.255.0">
<tftp root="/var/lib/tftproot" />
<dhcp>
<range start="192.168.122.2" end="192.168.122.254" />
<bootp file="pxeboot.img"/>
</dhcp>
</ip>
</network>
When the attributes are present, these are passed to the
arguments to dnsmasq:
dnsmasq [...] --enable-tftp --tftp-root /srv/tftp --dhcp-boot pxeboot.img
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ^^^^^^^^^^^^^^^^^^^^^^^
from <tftp /> from <bootp />
At present, only local tftp servers are supported (ie, dnsmasq runs as
the tftp server), but we could improve this in future by adding a
server= attribute.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2009-09-21 Paolo Bonzini <pbonzini@redhat.com>
Jeremy Kerr <jk@ozlabs.org>
* docs/formatnetwork.html.in: Document new tags.
* docs/formatnetwork.html: Regenerate.
* docs/schemas/network.rng: Update.
* src/network_conf.c (virNetworkDefFree): Free new fields.
(virNetworkDHCPRangeDefParseXML): Parse <bootp>.
(virNetworkIPParseXML): New, parsing <dhcp> and <tftp>.
(virNetworkDefParseXML): Use virNetworkIPParseXML instead of
virNetworkDHCPRangeDefParseXML.
(virNetworkDefFormat): Pretty print new fields.
* src/network_conf.h (struct _virNetworkDef): Add netboot fields.
* src/network_driver.c (networkBuildDnsmasqArgv): Add
TFTP and BOOTP arguments.
* tests/Makefile.am (EXTRA_DIST): Add networkschemadata.
* tests/networkschematest: Look in networkschemadata.
* tests/networkschemadata/netboot-network.xml: New.
* daemon/default-network.xml: Move to src/network/default.xml
* daemon/libvirtd_qemu.aug, daemon/test_libvirtd_qemu.aug: Move
to src/qemu/
* src/qemu.conf: Move to src/qemu/qemu.conf
* daemon/Makefile.am: Remove rules for default-nmetwork.xml and
libvirtd_qemu.aug and test_libvirtd_qemu.aug. Fix typo in
uninstall-local that would install polkit again.
* src/Makefile.am: Add rules for installing network/default.xml
and the qemu/*.aug files. Add test case for QEMU augeas files.
Add uninstall-local rule for files/directories created during
install. Rename install-exec-local to install-data-local.
Only install qemu.conf if WITH_QEMU is set.
* tests/networkschematest: Update for XML location move
